|
| 1 | Dismantling clearing away & carefully stacking materials - weathering course & pressed tiles. |
| 2 | Reinforced cement concrete 1:1½:3 ( One cement one and half sand and three broken granite metal ) using 20 mm ISS size HBG metal excluding cost of reinforcement steel and shuttering for centering but including cost and conveyance of all other materials to working site, laying concrete, compacting, curing, dewatering if necessary and finishing neatly etc. complete complying with standard specification. |
| 3 | Supplying fabricating and placing in position of mild steel or ribbed tar steel for reinforced cement concrete works including cost of steel binding wire all labour charges for cutting fabrication and placing of rods and other incidental charges etc., complete as per standard specification. |
| 4 | Brickworkin cementmortar1:5 (one cement and five sand)using second class chamberbricks of standerd size22cm x 11 cm x 7 cmincluding cost and conveyance of all materials to siteand labour charges etccompleteas perStandard specification. |
| 5 | Plastering with cement mortar 1: 5 mix (One cement and fivesand)12 mm thickincluding cost and conveyance of all materials, finishing, curing, and all labour charges etc. complete as per Standard specification. |
| 6 | Ceiling plastering with cement mortar 1: 3 mix (One cement and fivesand)20mm thickincluding cost and conveyance of all materials, finishing, curing, and all labour charges etc. complete as per Standard specification. |
| 7 | Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete. |
| 8 | Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing. The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete |
| 9 | Painting two coats with ready mixed plastic emulsion of first class quality paint and of approved colour over a priming coat including thorough scrapping clean removel of dirt,including cost of all materials and all labour charge etc complete as per standard specification. |
| 10 | Supply, fabrication and fixing in position of weldmesh grill for ventilators with wooden frame work alround including cost of all materials, labour, lead, lift etc., complete. |
| 11 | Providing and fixing pre-painted three track, three panel sliding system fabricated from roll formed sections made of galvanized steel colour coated (Base steel as per IS 513 \"D\" quality, galvanized as per IS 277 with zinc of 120 grams / sqm.) with total coated thickness of 0.58mm. Paint specification: Coated sections should be with primer coat of epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns.Dimensions of sections: Section for outer frame three track should be of 92mm x 44mm, section for shutter should be of 35mm x 49mm for window, section for euro groove should be of 25mm x 24mm and for lap strip should be 30mm x 41mm.Fixing details: The frame and shutter sections should be cut to length, joined with corner brackets made of glass filled nylon. Ethyl Propylene Diamine Monomer (EPDM) Gasket should be used all around glass. Accessories: Corner brackets made of glass filled nylon. Gasket made of Ethyl Propylene Diamine Monomer (EPDM). Locking system should be of single pin locking for windows. Single wheel rollers for windows should be provided. Glass: Glass shutter and fixed glass portion should be provided with a glass of 4mm pinhead glass. Window frame should be fixed to brick / concrete masonry by using nylon self-expanding caps and driving MS electro plated 80mm long screws into the caps through frames. |
| 12 | Wiring with 2 x 1.5sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150 x 100 x 113mm TW switch box for 5 A 3 pin non inter locking CS plug with painting of suitable colour with continuous earth wire connection of 15 SWG TC wire for open PVC plug point. (SD-37) |
| 13 | Supply and fixing of 40 W LED tube light fitting with ISI Mark with all accessoreis including cost of an LED light with accessories and fitting charges etc., complete. |
| 14 | GST Amount for providing Service to Government Contract Works for the Above construction works. (GST Amount is the Total GST Amount for total overall quoted amount above this row for this work) |
