Procurement Of Inductive Proximity Barrel Type Sensor & Float Switch
2
Inductive proximity barrel type sensor 1) Type- Inductive proximity barrel type sensor. 2)Connection- M12x1-Male, 4-pole & Connector, M12x1-Male, 4-pin. 3) Load Capacitance max. at Ue -1 µF. 4)Operating voltage Ub- 10...30 VDC. 5) Switching frequency- 3000 Hz. 6) Output Resistance Ra- 100.0 k Ohm +2D. 7) Rated Insulation voltage Ui- 250 V AC. 8) Rated operating current Ie- 200 mA. 9) Dimension- Ø 12 x 65mm. 10) Mounting quasi shielded rated operating distance- 8 mm. Make-TELEMECHANIQUE/SICK/OMRON/BALLUFF
3
Inductive proximity barrel type sensor 1) Type- Inductive proximity barrel type sensor. 2)Connection- M12x1-Male, 4-pole & Connector, M12x1-Male, 4-pin. 3) Load Capacitance max. at Ue -1 µF. 4)Operating voltage Ub- 10...30 VDC. 5) Switching frequency- 2500 Hz. 6) Output Resistance Ra- 100.0 k Ohm +2D. 7) Rated Insulation voltage Ui- 250 V AC. 8) Rated operating current Ie- 200 mA. 9) Dimension- Ø 12 x 70mm. 10) Mounting quasi shielded rated operating distance- 4 mm. Make-TELEMECHANIQUE/SICK/OMRON/BALLUFF
4
Float Switch \"General specification for Float Switch Sensor for Water Level Controller with 3 MeterWire: Float Switch Sensor for Water Level Controller with 3 Meter Wire: 1. Endurance: =500,000times of wire and Plastic Body Electrical 2. Rated voltage: 250V and Rated current: 8A/Contacts: NO+NC andWeight: 660 g 3. Cable: 3 Meter (customized wire length is available)/ A float switch is a device used to detectthe level of liquid within a tank. The switch may be used in a pump, an indicator, an alarm, or other devices andUse: Water Level, liquid level Controller INSTRUCTIONS, for INSTALLATION Insert the cable in the counterweight (yellow color part), from the conical part and rotate it. 4.Thus causing the plastic ring inserted in theopening to become detached (if necessary this operation can be facilitated with the use of a screwdriver). Thering should then be positioned in the point where it is desired to block the counterweight. Force the counterweighton the ring by rotating it using a slight pressure 5. Item Dimensions LxWxH 24 x 12 x 9 Centimeters 6. BallMaterial Type Plastic 7. Breaking Strength 660.00 grams 8. Capacity 660.00 grams 9. ISO Range : 9 10. InsideDiameter 9 centimeters 11. Item Depth 12-centimeters 12. Item Shape Round 13. Colour:- Yellow\"Consignee ACOS OF CONCERNED DEPOT Delhi 23.00 Numbers3. T AND CF.O.RDescriptionDestinationDelivery PeriodDescription Delivery /Completion Rate of SupplyFor all items Completion : Within 30 DaysPayment TermsS.No DescriptionPayment Terms1 100% payment against receipt, inspection and acceptance of material by the consignee at destination.Statutory Variation ClauseS.No Description1 Statutory Variation in taxes and duties, or fresh imposition of taxes and duties by State/ Central Governments inrespect of the items stipulated in the contract (and not the raw materials thereof), within the original deliveryperiod stipulated in the contract, or last unconditionally extended delivery period shall be to DMRCs account.Only such variation shall be admissible which takes place after the submission of bid. No claim on account ofstatutory variation in respect of existing tax/duty will be accepted unless the tenderer has clearly indicated in hisoffer the rate of tax/duty considered in his quoted rate. No claim on account of statutory variation shall beadmissible on account of misclassification by the supplier/ contractor.Option ClauseS.No Description1 The purchaser shall be entitled to vary the order quantity upto +/-25% anytime within the delivery period(including extended delivery period) on the same terms and conditions. The increase in quantity with respect tothe tender quantity can be done even at the time of ordering and the tenderer shall be bound to accept thequantity so ordered on the basis of his original offer. The purchaser shall be entitled to exercise +/-25% optionclause in one or more than one instalment as long as the total variation in quantity does not exceed the limit of25% of ordered quantity.4. ELIGIBILITY CONDITIONSSpecial Eligibility CriteriaS.No. Description Confirmation Remarks DocumentsRequired Allowed UploadingPage 2 of 4 Run Date/Time: 19/05/2023 11:16:08STORES/DMRCTENDER DOCUMENTTender No DMRCGEN11024604 Closing Date/Time 02/06/2023 15:001 As per tender Yes Yes Not Allowed5. COMPLIANCE CONDITIONSCommercial-ComplianceS.No. Description Confirmation Remarks DocumentsRequired Allowed Uploading1 Please enter the percentage of local content in the material being offered. No Yes AllowedPlease enter 0 for fully imported items, and 100 for fully indigenous items. (Optional)The definition and calculation of local content shall be in accordance withthe Make in India policy as incorporated in the tender conditions.2 All the participating tenderers are mandatorily required to submit a Yes Yes Allowedcertificate of their compliance in regard to restrictions of procurement from (Mandatory)the bidders of countries sharing land borders with India as per the formatincluded in Appendix-1.General InstructionsS.No. Description Confirmation Remarks DocumentsRequired Allowed Uploading1 As per Tender No No Not AllowedSpecial ConditionsS.No. Description Confirmation Remarks DocumentsRequired Allowed Uploading1 As per Tender No No Not Allowed2 The purchaser reserves the right to reject or accept any offer in whole or No No Not Allowedpart without assigning any reason.UndertakingsS.No. Description Confirmation Remarks DocumentsRequired Allowed Uploading1 The bidder confirms that Rates and other financial terms quoted in relevant No No Not Allowedcolumns of financial bid will only be ruling terms for acceptance , and suchterms quoted anywhere else should be ignored. [Denial of this condition notrecommended]S.No. Description Confirmation Remarks DocumentsRequired Allowed Uploading1 Firm shall deliver the material at various depot of DMRC. Yes Yes Not AllowedS.No. Description Confirmation Remarks DocumentsRequired Allowed Uploading1 Firm shall provide the HSN code for the items. Yes Yes Allowed(Optional)S.No. Description Confirmation Remarks DocumentsRequired Allowed Uploading1 12 months from the date of Supply. Yes Yes Allowed(Optional)6. DOCUMENTS ATTACHED WITH TENDERS.No. Document Name Document Description1 Appendix1.pdf Appendix 1Page 3 of 4 Run Date/Time: 19/05/2023 11:16:08STORES/DMRCTENDER DOCUMENTTender No DMRCGEN11024604 Closing Date/Time 02/06/2023 15:00The tenderers in their bid shall indicate the details of their GST Jurisdictional Assessing Officers (Designation, Address &email id). In case of a contract award, a copy of Purchase Order shall be immediately forwarded by Purchaser to theGST Jurisdictional assessing officer mentioned in Tenderers bidThis tender complies with Public Procurement Policy (Make in India) Order 2017, dated 15/06/2017, issued byDepartment of Industrial Promotion and Policy, Ministry of Commerce, circulated vide Railway Board letter no.2015/RS(G)/779/5 dated 03/08/2017 and 27/12/2017 and amendments/ revisions thereof.As a Tender Inviting Authority, the undersigned has ensured that the issue of this tender does not violate provisions ofGFR regarding procurement through GeM.Digitally Signed By Dy.CMM/DMRC ( NAVNEET KUMAR )
5
Float Switch Sensor for Water Level Controller with 3 Meter Wire: 1. Endurance: =500,000times of wire and Plastic Body Electrical 2. Rated voltage: 250V and Rated current: 8A/Contacts: NO+NC andWeight: 660 g 3. Cable: 3 Meter (customized wire length is available)/ A float switch is a device used to detectthe level of liquid within a tank. The switch may be used in a pump, an indicator, an alarm, or other devices andUse: Water Level, liquid level Controller INSTRUCTIONS, for INSTALLATION Insert the cable in the counterweight (yellow color part), from the conical part and rotate it. 4.Thus causing the plastic ring inserted in theopening to become detached (if necessary this operation can be facilitated with the use of a screwdriver). Thering should then be positioned in the point where it is desired to block the counterweight. Force the counterweighton the ring by rotating it using a slight pressure 5. Item Dimensions LxWxH 24 x 12 x 9 Centimeters 6. BallMaterial Type Plastic 7. Breaking Strength 660.00 grams 8. Capacity 660.00 grams 9. ISO Range : 9 10. InsideDiameter 9 centimeters 11. Item Depth 12-centimeters 12. Item Shape Round 13. Colour:- Yellow\"
We takes all possible care for accurate & authentic tender information, however Users
are requested to refer Original source of Tender Notice / Tender Document published by
Tender Issuing Agency before taking any call regarding this tender.
