Tender For Jet Pump Monoblock Pump Bare Pump Underwater Pump Vtpump India Mark - 2 And Mark - 3 Hand Pump Repairing And Spare Parts Rate For Zilha Parishad Bhandara

Sharing tender

Jet Pump Monoblock Pump Bare Pump Underwater Pump Vtpump India Mark - 2 And Mark - 3 Hand Pump Repairing And Spare Parts Rate For Zilha Parishad Bhandara , Jet Pump,Monoblock Pump, Bare Pump Underwater Pum All Submit Rate As Pergsda-Item Sheet , India Mark -2 & 3 Hand Pump Repairing Drive Out Thepipe Line With Diameter Of 65.0 M.M. , Drive Outthepipe Line With Diameter Of 65.0 M.M Which Fell In Well. , Drive Out Thepipe Line With Diameter Of 32.0 M.M From Whichfell In Well. , Drive Out Thepipe Line With Diameter Of 32.0 M.M From Well. , Repairing Of Jet Motor Pump & Pipelinedrive Out Inner Pipeline With Jet Assembly Of Jetpump From 1.0 Hp To 5.0 Hp Well. , To Fit The Inner And Outer Pipeline Of The Jet Pump In 1.0 Hp To5.0 Hp Well. , To Insert Inner Pipeline Of Jetpump In Well. (After Repairing.) , To Insert Inner & Outer Pipeline Of Jetpump In Well. (After Repairing.) , To Pull Out The Stucked, Fell Or Caught In Dreg Pump Set.( Contracter Use Their Own Tools.) , To Increse Or Reduse The Pipe Line Of Jet Pump Inh Well. ( For Every 3.0 M. ) , To Submit In The Officejet Pump, Motor Pipeline, Starter Panel Board Tin & Other Assesaries Of Laghu Panee Purwatha Yojna In Well. , New Pump Set (Upto 1.0 To 5.0 Hp) To Fit In Well, To Give Panel Wiring Arthig Test Report & Start After Electric Supply. (Z.P. Providespumpset Panel, Arthing Material G.I. Wire, Plate, Pipe Andother Assesaries.) , To Drive Out Motor And Pump From Jet Pump , To Fit1.0 Hp To 5.0 Hp Jet Motor Pump. , To Rewinding Electric Motor With Copper Wire , Above Rate Valid Forwithout Returning Old Copper Wire, 1.0 Hp To 5.0 Hp Open Pump Motor Rewinding. , To Open The Jet Motor, Over Oiling, Fitting And Testing , Roter Pump Shaft Turning And Polishing. , To Make Upper And Lower Bush Of Baring Cover Sit And Housing Of Jet Pump. , To Test Electric Pump On Site ( Transport And With Minor Repairing) , To Repaire Panel Board & Starter Of All Types Motor & Any Hp Control Panel Starter Minor Repairing To Fit Grif Set, Rottery Swich, Contracter Plate, Ampear Meter, Volt Meter, On-Off Switch, Fuse And Minor Wiring. , Starter Panel Board Main Repairing & To Fit Coilrelay, Single Phasing Preventer Water Label Guard & Totle Wiring Of 1.0 Hp To 10.0 Hp Pump. , Starter Panel Board Main Repairing & To Fit Coilrelay, Single Phasing , Preventer Water Label Guard & Totle Wiring Of 10.0 Hp To 30 Hp Pump. , Preventer Water Label Guard & Totle Wiring Of 31.0 Hp To 40 Hp Pump. , To Remove Tin Shed Flashing Of Pump If Necessary And Fit As It Is After Work. , To Remove Handpump With Pipeline For Flashing And Insert 10 Feet G.I.Pipeline Towards 32 M.M. Dimeter& Remove After Flashing And Fithandpump As It Is Before. , To Remove Handpump For Capacity Test And After Testing Fit As It Is Before. , Single Phase 1 Hp To 2 Hp Electric Pump Capacity Test For Regular Three Hour With Help Of Generator , Yieldtest 1 Hp To 2 Hp Electric Pump Capacity Test For Regular Three Hour With Help Of Generatorwith Necc Equip , Yieldtest 2 Hp To5 Hp Electric Pump Capacity Test For Regular Three Hour With Help Of Generatorwith Necc Equip , Yield Test 2 Hp To5 Hp Electric Pump Capacity Test For Regular Three Hour Withouthelpof Generatorwith Necc Equip , Spare Parts Of Jet Pump Baring Upper , Baring Lower , Empelor Key , Pump Bush , Air Fan ( With Pvc Pin) , Stand Nut Kit , Nut Bolt Kit , Air Cock , Pressure Regulating Volve , Pressure Regulating Difrom , Baring Plate Top / Bottom , Jet Assembly Packer Type Full , Packer Foot Volve , Packer Rubber Seal Set , Packer Backet Set , Gland Rope , Rubber Packing Set , Gland Rope Plate , Empelor , D) Other Material G. I. Coplling Heavy Duty , I) 32 M.M. , Ii) 40 M.M. , Iii) 50 M.M. , Iv) 65 M.M. , V) 75 M.M. , Vi) 100 M.M. , Vii) 125 M.M. , Viii) 150 M.M. , Bend Heavy Duty , I) 32 M.M. , Ii) 40 M.M. , Iii) 50 M.M. , Iv) 65 M.M. , V) 75 M.M. , Vi) 100 M.M. , Vii) 125 M.M. , Viii) 150 M.M. , 3) Foot Volve:I) 32 M.M. , Ii) 40 M.M. , Iii) 50 M.M. , Iv) 65 M.M. , V) 75 M.M. , Vi) 100 M.M. , Vii) 125 M.M. , Viii) 150 M.M. , Wooden Board 3 X 2 F X ½ “ , Iron Box 18 Guage Tin 3F X 2F X 1F , G.I.Pipe 1½“ / 1¼ “ Cutting Threding , G.I.Pipe 2“ Cutting Threding , G.I.Pipe 2½“ / 3 “ Cutting Threding , E)Submercible Pump Repairing: 1.0 Hp To 3.5 Hp , 4.0 Hp To 5.0 Hp , 6.0 Hp To 10.0 Hp , 11.0 Hp To 15.0 Hp , 16.0 Hp To 20.0 Hp , 21.0 Hp To 30.0 Hp , 31.0 Hp To 50.0 Hp , F) To Remove Motor Pump Set With Pipelinefrom Well: 1 Hp To 6.0 Hp , 7.0 Hp To 15 Hp , 16.0 Hp To 30.0 Hp , 31.0 Hp To 50.0 Hp , G) To Pull Out The Stuck, Fell Or Caught In Dreg Pump Set With Pipelinefrom Well: 1 Hp To 6.0 Hp , 2) 7.0 Hp To 15 Hp , 3)16.0 Hp To 30.0 Hp , 4)31.0 Hp To 50.0 Hp , H) To Fit Motor Pump In Well With Pipe Line: 1)1 Hp To 6.0 Hp , 2)7.0 Hp To 15 Hp , 3) 16.0 Hp To 30.0 Hp , 4) 31.0 Hp To 50.0 Hp , I) To Increase Or Reduse Pipeline Of Submercible Pump In Well Rate 3 Meter / Per Pipe: 1 Hp To 6.0 Hp , 7.0 Hp To 15 Hp , 16.0 Hp To 30.0 Hp , 31.0 Hp To 50.0 Hp , J) To Submit In The Officejet Pump, : 1 Hp To 7.5 Hp , 8.5 Hp To 15 Hp , 16.0 Hp To 30.0 Hp , 31.0 Hp To 50.0 Hp , K) New Pump Set (Upto 1.0 To 5.0 Hp) :1 Hp To 7.5 Hp , 8.5 Hp To 15 Hp , 16.0 Hp To 30.0 Hp , 31.0 Hp To 50.0 Hp , L) To Open Sub Motor, Repairing, Fitting And Testing.: 1 Hp To 7.5 Hp , 8.5 Hp To 15 Hp , 16.0 Hp To 30.0 Hp , 31.0 Hp To 50.0 Hp , M) To Open Sub Pump, Repairing, Fitting And Testing.:1)1 Hp To 7.5 Hp , 2) 8.5 Hp To 15 Hp , 3)16.0 Hp To 30.0 Hp , 4)31.0 Hp To 50.0 Hp , N) To Repaire Sub Motor And Sub Pump:To Sub Motor / Pump Bush Fitting Per , Damage Stater Repairing , Roter Shaft Turning And Polishing , Damage Roter Repairing (Rewinding) , Sub Pump Shaft Turning & Polishing , To Joint Cable With Kit , O) Sub Motor & Sub Pump Spare Parts1 To 5 Hp: I) Sub Motor Bush , Ii) Sub Pump Bush , Thirst Baring Block , Thirst Baring Full , Block , Ring , Upper Stage Casing , Lower Stage Casing , Middle Stage Casing , I) Empelor , Ii) Brass Empelor , Nekring , Defuser , Pump Key , Rubber Parts Kit , Submotor Base , Stenner , Male- Female Bush , Male- Famale Key , Nrv Stage Casing , Stud Big , Stud Small , Motor Bush Housing , I) Upper , Ii) Lower , Alen Srew , Ss Slivemotor /Pump , Ss Slive Cover , O) Sub Motor & Sub Pump Spare Parts1 To 7.5 Hp: I) Sub Motor Bush , Ii) Sub Pump Bush , Thirst Baring Block , Thirst Baring Full , Block , Ring , Upper Stage Casing , Lower Stage Casing , Middle Stage Casing , I) Empelor , Ii) Brass Empelor , Nekring , Defuser , Pump Key , Rubber Parts Kit , Submotor Base , Stenner , Male- Female Bush , Male- Famale Key , Nrv Stage Casing , Stud Big , Stud Small , Motor Bush Housing , I) Upper , Ii) Lower , Alen Srew , Ss Slivemotor /Pump , Ss Slive Cover , O) Sub Motor & Sub Pump Spare Parts 8 To15 Hp :I) Sub Motor Bush , Ii) Sub Pump Bush , Thirst Baring Block , Thirst Baring Full , Block , Ring , Upper Stage Casing , Lower Stage Casing , Middle Stage Casing , I) Empelor , Ii) Brass Empelor , Nekring , Defuser , Pump Key , Rubber Parts Kit , Submotor Base , Stenner , Male- Female Bush , Male- Famale Key , Nrv Stage Casing , Stud Big , Stud Small , Motor Bush Housing , I) Upper , Ii) Lower , Alen Srew , Ss Slivemotor /Pump , Ss Slive Cover , O) Sub Motor & Sub Pump Spare Parts16 To30 Hp: I) Sub Motor Bush , Ii) Sub Pump Bush , Thirst Baring Block , Thirst Baring Full , Block , Ring , Upper Stage Casing , Lower Stage Casing , Middle Stage Casing , I) Empelor , Ii) Brass Empelor , Nekring , Defuser , Pump Key , Rubber Parts Kit , Submotor Base , Stenner , Male- Female Bush , Male- Famale Key , Nrv Stage Casing , Stud Big , Stud Small , Motor Bush Housing , I) Upper , Ii) Lower , Alen Srew , Ss Slivemotor /Pump , Ss Slive Cover , 1)Three Ply Coreflat Flexible Submercible Cable: I) 1.5 Sq.M.M. , Ii) 2.5 Sq.M.M. , Iii) 4 Sq.M.M. , Iv) 6 Sq.M.M. , V) 10 Sq.M.M. , Vi) 1.5 Sq.M.M. , 1)Three Ply Coreflat : Arm Cable:I) 1.00 Sq.M.M. , Ii) 1.50 Sq.M.M. , Iii) 2.50 Sq.M.M. , Iv) 4.00 Sq.M.M. , V) 6.00 Sq.M.M. , Vi) 10.00 Sq.M.M. , Vii) 16.00 Sq.M.M. , Viii) 25.00 Sq.M.M. , Ix) 35.00 Sq.M.M. , X) 50.00 Sq.M.M. , Copper Wire P.V.C. Insulated & P.V.C. Coated: I) 3/20 , Copper Wire P.V.C. Insulated & P.V.C. Coated: Ii) 7/20 , Copper Wire P.V.C. Insulated & P.V.C. Coated: Iii) 7/16 , 27)New Pump Shaft I) 1.5 Hp To 6 Hp , 27)New Pump Shaft Ii) 7.5 Hp To 15 Hp , 27)New Pump Shaft Iii) 16 Hp To 30 Hp , Borewell Protecting Plate , Borewell Protecting Cover , P)25.0 Hp To 40 Hp V.T. Motor Pump Set Repairing 25Hp: Drive Out V.T. Motor From Well , V.T. Pump Fit In Well , Drive Out Colume Assembly With Pipeline From Well , To Fit Colume Assembly With Pipeline In Well , To Open V.T. Motor , V.T. Motor Fitting & Testing , Bowl Assembly Fitting & Testing , To Open Bowl Assembly , V.T. Pump Rewinding With Copper Wire. Withoutreturning Old Copper Wire , Allignment Checking & Repairing , I) Line Shaft , Ii) Colume Pipe , Iii) Oil Tube , Cutting & Threading , I) Line Shaft (R.H./L.H) , Ii) Colume Pipe (R.H./L.H) , Iii) Oil Tube (R.H./L.H) , To Fit New Flage, Threading Coller, Welding,Nutboltin Colume Pipe , To Making ,Bearing Sheet On Lathe Machine , Bearing Plate Both Side , P)25.0 Hp To 40 Hp V.T. Motor Pump Set Repairing 35Hp: Drive Out V.T. Motor From Well , V.T. Pump Fit In Well , Drive Out Colume Assembly With Pipeline From Well , To Fit Colume Assembly With Pipeline In Well , To Open V.T. Motor , V.T. Motor Fitting & Testing , Bowl Assembly Fitting & Testing , To Open Bowl Assembly , V.T. Pump Rewinding With Copper Wire. Withoutreturning Old Copper Wire , Allignment Checking & Repairing , I) Line Shaft , Ii) Colume Pipe , Iii) Oil Tube , Cutting & Threading , I) Line Shaft (R.H./L.H) , Ii) Colume Pipe (R.H./L.H) , Iii) Oil Tube (R.H./L.H) , To Fit New Flage, Threading Coller, Welding,Nutboltin Colume Pipe , To Making ,Bearing Sheet On Lathe Machine , Bearing Plate Both Side , P)25.0 Hp To 40 Hp V.T. Motor Pump Set Repairing 40Hp : Drive Out V.T. Motor From Well , V.T. Pump Fit In Well , Drive Out Colume Assembly With Pipeline From Well , To Fit Colume Assembly With Pipeline In Well , To Open V.T. Motor , V.T. Motor Fitting & Testing , Bowl Assembly Fitting & Testing , To Open Bowl Assembly , V.T. Pump Rewinding With Copper Wire. Withoutreturning Old Copper Wire , Allignment Checking & Repairing , I) Line Shaft , Ii) Colume Pipe , Iii) Oil Tube , Cutting & Threading , I) Line Shaft (R.H./L.H) , Ii) Colume Pipe (R.H./L.H) , Iii) Oil Tube (R.H./L.H) , To Fit New Flage, Threading Coller, Welding,Nutboltin Colume Pipe , To Making ,Bearing Sheet On Lathe Machine , Bearing Plate Both Side , Q)25 Hp To 40 Hp V.T. Pum Spare Part 25Hp : 1) V.T. Motor Baring , I) Upper , Ii) Lower , Discharge & Sectioncase Baring Bush Gun Metal , Water Seal (Oil Water Separater) , Line Shaft , Oil Tube , T.T. Plate Cast Iron , Brain Rubber Bush (Spider) , Net (Cast Iron) , Nut Bolt ¾“ X 2 “ , Nut Bolt ¾“ X 6 “ , Rubber Shit , T.T. Plate Bush , Neck Ring (Gun Metal) , Impelor(Gun Metal) , Browl Assembly Casing , 6” Colume Pipe M.S. , 8” Colume Pipe M.S. , Transformer Oil , Pump Colet , Shaft Tube Oil 10 No. , Impelor Pump Shaft , Litern Ring , Gide Spider , Colume Pipe Coplling , Line Shaft Coplling , Oil Tube Baring , Glad Nut , Top Oil Tube , Spider Baring Bush , Guide Spider Rubber Bush With Sirclip , Rubber Bush/ Baring , Line Shaft Slive S.S. , Water Lubricating Tube , Stuffing Box Bush & With Gaskit , Stuffing Box Baring , Latern Ring , Sole Plate , Base Plate , Water Deflector , Q)25 Hp To 40 Hp V.T. Pum Spare Part 25Hp : 1) V.T. Motor Baring , I) Upper , Ii) Lower , Discharge & Sectioncase Baring Bush Gun Metal , Water Seal (Oil Water Separater) , Line Shaft , Oil Tube , T.T. Plate Cast Iron , Brain Rubber Bush (Spider) , Net (Cast Iron) , Nut Bolt ¾“ X 2 “ , Nut Bolt ¾“ X 6 “ , Rubber Shit , T.T. Plate Bush , Neck Ring (Gun Metal) , Impelor(Gun Metal) , Browl Assembly Casing , 6” Colume Pipe M.S. , 8” Colume Pipe M.S. , Transformer Oil , Pump Colet , Shaft Tube Oil 10 No. , Impelor Pump Shaft , Litern Ring , Gide Spider , Colume Pipe Coplling , Line Shaft Coplling , Oil Tube Baring , Glad Nut , Top Oil Tube , Spider Baring Bush , Guide Spider Rubber Bush With Sirclip , Rubber Bush/ Baring , Line Shaft Slive S.S. , Water Lubricating Tube , Stuffing Box Bush & With Gaskit , Stuffing Box Baring , Latern Ring , Sole Plate , Base Plate , Water Deflector , Q)25 Hp To 40 Hp V.T. Pum Spare Part 40Hp: 1) V.T. Motor Baring , I) Upper , Ii) Lower , Discharge & Sectioncase Baring Bush Gun Metal , Water Seal (Oil Water Separater) , Line Shaft , Oil Tube , T.T. Plate Cast Iron , Brain Rubber Bush (Spider) , Net (Cast Iron) , Nut Bolt ¾“ X 2 “ , Nut Bolt ¾“ X 6 “ , Rubber Shit , T.T. Plate Bush , Neck Ring (Gun Metal) , Impelor(Gun Metal) , Browl Assembly Casing , 6” Colume Pipe M.S. , 8” Colume Pipe M.S. , Transformer Oil , Pump Colet , Shaft Tube Oil 10 No. , Impelor Pump Shaft , Litern Ring , Gide Spider , Colume Pipe Coplling , Line Shaft Coplling , Oil Tube Baring , Glad Nut , Top Oil Tube , Spider Baring Bush , Guide Spider Rubber Bush With Sirclip , Rubber Bush/ Baring , Line Shaft Slive S.S. , Water Lubricating Tube , Stuffing Box Bush & With Gaskit , Stuffing Box Baring , Latern Ring , Sole Plate , Base Plate , Water Deflector , I) Drive Out 1 Hp To 3 Hp Monoblock Pump , Ii) Drive Out 4 Hp To 10 Hp Monoblock Pump , Ii) 2 To 3Hp Monoblock Motor Rewinding , Iii) 4 To 5Hp Monoblock Motor Rewinding , Iv) 6 To 7½Hp Monoblock Motor Rewinding , V) 8 To 10Hp Monoblock Motor Rewinding , Monoblock Pump Open, Repairing, Fitting & Testing I) 1 To 1½Hp , Monoblock Pump Open, Repairing, Fitting & Testing Ii) 2 To 5Hp , Monoblock Pump Open, Repairing, Fitting & Testingiii) 6 To 10Hp , Roter Pump Shaft Turning & Polishingi) 1 To 5 Hp , Roter Pump Shaft Turning & Polishingii) 6 To 10Hp , To Make Monoblock Pump Bush & Housing (Baring)I) 1 To 1½Hp , To Make Monoblock Pump Bush & Housing (Baring)Ii) 2 To 5Hp , To Make Monoblock Pump Bush & Housing (Baring)Iii) 6 To 10Hp , Tofit New Pump Set I) 1 To 1½Hp , Tofit New Pump Setii) 2 To 5Hp , Tofit New Pump Set Iii) 6 To 10Hp , T) Monoblock Pump Spare Partsbaring1 To 1½ Hp(Driving Side) , Baring (Driven Side) , Impelor Key , Pump Bush , Air Fan , Sturnut Key , Baring Plate Both Side1 Item , Water Seal , Gland Rope , Gland Bush , Gland Plate , Roter Fitted Shaft , Latern Ring , Impelor Brass , Impelor C.I. , Defuser , Baring Housing , Neck Ring , Foot Volve , Fluge (Dilevery/ Suction) , Shaft Sleve , Delivery Casing , Stater Fitted Motorbody , Spacer , Fan Cover , Water Deflector , T) Monoblock Pump Spare Parts 2 To 3 Hp Baring (Driving Side) , Baring (Driven Side) , Impelor Key , Pump Bush , Air Fan , Sturnut Key , Baring Plate Both Side1 Item , Water Seal , Gland Rope , Gland Bush , Gland Plate , Roter Fitted Shaft , Latern Ring , Impelor Brass , Impelor C.I. , Defuser , Baring Housing , Neck Ring , Foot Volve , Fluge (Dilevery/ Suction) , Shaft Sleve , Delivery Casing , Stater Fitted Motorbody , Spacer , Fan Cover , Water Deflector , T) Monoblock Pump Spare Parts 4 To 5 Hp Baring (Driving Side) , Baring (Driven Side) , Impelor Key , Pump Bush , Air Fan , Sturnut Key , Baring Plate Both Side1 Item , Water Seal , Gland Rope , Gland Bush , Gland Plate , Roter Fitted Shaft , Latern Ring , Impelor Brass , Impelor C.I. , Defuser , Baring Housing , Neck Ring , Foot Volve , Fluge (Dilevery/ Suction) , Shaft Sleve , Delivery Casing , Stater Fitted Motorbody , Spacer , Fan Cover , Water Deflector , T) Monoblock Pump Spare Partsbaring 6 To 7½Hp (Driving Side) , Baring (Driven Side) , Impelor Key , Pump Bush , Air Fan , Sturnut Key , Baring Plate Both Side1 Item , Water Seal , Gland Rope , Gland Bush , Gland Plate , Roter Fitted Shaft , Latern Ring , Impelor Brass , Impelor C.I. , Defuser , Baring Housing , Neck Ring , Foot Volve , Fluge (Dilevery/ Suction) , Shaft Sleve , Delivery Casing , Stater Fitted Motorbody , Spacer , Fan Cover , Water Deflector , T) Monoblock Pump Spare Partsbaring 8 To 10Hp(Driving Side) , Baring (Driven Side) , Impelor Key , Pump Bush , Air Fan , Sturnut Key , Baring Plate Both Side1 Item , Water Seal , Gland Rope , Gland Bush , Gland Plate , Roter Fitted Shaft , Latern Ring , Impelor Brass , Impelor C.I. , Defuser , Baring Housing , Neck Ring , Foot Volve , Fluge (Dilevery/ Suction) , Shaft Sleve , Delivery Casing , Stater Fitted Motorbody , Spacer , Fan Cover , Water Deflector , U) Bare Pump Repairingto Drive Out Bare Pump I) 10 To 20 Hp , Ii) 21 To 50 Hp , Bare Pump To Open, Repairing, Fitting & Testing I) 10 To 20 Hp , Ii) 21 To 50 Hp , Pump Shaft Turning & Polishing I) 10 To 20 Hp , Ii) 21 To 50 Hp , To Make Pump Bush & Housing (Baring) I) 10 To 20 Hp , Ii) 21 To 50 Hp , To Fit New Bare Pump I) 10 To 20 Hp , Ii) 21 To 50 Hp , Pump Repairing & Fittingi) 10 To 20 Hp , Ii) 21 To 50 Hp , To Make Gland Bush Housing I) 10 To 20 Hp , Ii) 21 To 50 Hp , Drive Out Bare Pump Pipe Line With Foot Volve I) 10 To 20 Hp , Ii) 21 To 50 Hp , To Fit Bare Pump Pipeline With Foot Volve I) 10 To 20 Hp , Ii) 21 To 50 Hp , V) Bare Pump Spare Parts 10 To 15 Hp Baring (Ball Baring) , Rolar Baring , Impelor Key , Pump Bush , Stud Nut , Nut Bolt Kit , Air Cock , Base Plate , Water Seal , Gland Bush , Gland Plate , Pump Shaft , Latern Ring , Impelor Brass , Impelor (C.I) , Difuser , Baring Housing , Neck Ring (Small) , Neck Ring (Big) , Flasher , Foot Volve , Check Nut , Impelor Housing , Roter Casing , Roter , Delevery Casing , Stuffing Box Bush , Shaft Sleve , Water Deflector , Cuplling Half Flexible , Baring Cover , Grees Cup , Flage Section/ Delivery , V) Bare Pump Spare Parts 16 To 20Hp Baring (Ball Baring) , Rolar Baring , Impelor Key , Pump Bush , Stud Nut , Nut Bolt Kit , Air Cock , Base Plate , Water Seal , Gland Bush , Gland Plate , Pump Shaft , Latern Ring , Impelor Brass , Impelor (C.I) , Difuser , Baring Housing , Neck Ring (Small) , Neck Ring (Big) , Flasher , Foot Volve , Check Nut , Impelor Housing , Roter Casing , Roter , Delevery Casing , Stuffing Box Bush , Shaft Sleve , Water Deflector , Cuplling Half Flexible , Baring Cover , Grees Cup , Flage Section/ Delivery , V) Bare Pump Spare Parts 21 To 50 Hp Baring (Ball Baring) , Rolar Baring , Impelor Key , Pump Bush , Stud Nut , Nut Bolt Kit , Air Cock , Base Plate , Water Seal , Gland Bush , Gland Plate , Pump Shaft , Latern Ring , Impelor Brass , Impelor (C.I) , Difuser , Baring Housing , Neck Ring (Small) , Neck Ring (Big) , Flasher , Foot Volve , Check Nut , Impelor Housing , Roter Casing , Roter , Delevery Casing , Stuffing Box Bush , Shaft Sleve , Water Deflector , Cuplling Half Flexible , Baring Cover , Grees Cup , Flage Section/ Delivery , W) Bare Motor Repairingdrive Out Bare Motor , W) Bare Motor Repairingdrive Out Bare Motor I) 10 To 20 Hp , W) Bare Motor Repairingdrive Out Bare Motor Ii) 21 To 50 Hp , Bare Motor Rewinding I) 1 To 5 Hp , Bare Motor Rewinding Ii) 6 To 10 Hp , Bare Motor Rewinding Iii) 11 To 15 Hp , Bare Motor Rewinding Iv)16 To 20 Hp , Bare Motor Rewindingv) 21 To 30 Hp , Bare Motor Rewinding Vi) 31 To 35 Hp , Bare Motor Rewinding Vii) 36 To 40 Hp , Bare Motor Rewinding Viii) 41 To 50 Hp. , Motor Opening, Over Oiling, Fitting & Testingi) 1 To 5 Hp , Motor Opening, Over Oiling, Fitting & Testingii) 6 To 10 Hp , Motor Opening, Over Oiling, Fitting & Testing Iii) 11 To 15 Hp , Motor Opening, Over Oiling, Fitting & Testingiv)16 To 20 Hp , Motor Opening, Over Oiling, Fitting & Testing V) 21 To 30 Hp , Motor Opening, Over Oiling, Fitting & Testing Vi) 31 To 35 Hp , Motor Opening, Over Oiling, Fitting & Testingvii) 36 To 40 Hp , Motor Opening, Over Oiling, Fitting & Testing Viii) 41 To 50 Hp. , Roter Shaft Turning & Polishing I) 1 To 5 Hp , Roter Shaft Turning & Polishing Ii) 6 To 10 Hp , Roter Shaft Turning & Polishing Iii) 11 To 15 Hp , Roter Shaft Turning & Polishingiv)16 To 20 Hp , Roter Shaft Turning & Polishing V) 21 To 30 Hp , Roter Shaft Turning & Polishing Vi) 31 To 35 Hp , Roter Shaft Turning & Polishingvii) 36 To 40 Hp , Roter Shaft Turning & Polishing Viii) 41 To 50 Hp. , To Make Motor Bush & Housing (Baring Sheet) I) 1 To 5 Hp , To Make Motor Bush & Housing (Baring Sheet)Ii) 6 To 10 Hp , To Make Motor Bush & Housing (Baring Sheet)Iii) 11 To 15 Hp , To Make Motor Bush & Housing (Baring Sheet)Iv)16 To 20 Hp , To Make Motor Bush & Housing (Baring Sheet)V) 21 To 30 Hp , To Make Motor Bush & Housing (Baring Sheet)Vi) 31 To 35 Hp , To Make Motor Bush & Housing (Baring Sheet) Vii) 36 To 40 Hp , To Make Motor Bush & Housing (Baring Sheet) Viii) 41 To 50 Hp. , To Fit New Motor I) 1 To 5 Hp , To Fit New Motor Ii) 6 To 10 Hp , To Fit New Motoriii) 11 To 15 Hp , To Fit New Motoriv)16 To 20 Hp , To Fit New Motorv) 21 To 30 Hp , To Fit New Motorvi) 31 To 35 Hp , To Fit New Motorvii) 36 To 40 Hp , To Fit New Motor Viii) 41 To 50 Hp. , Panel Board & Starter Repairingi) 1 To 5 Hp , Panel Board & Starter Repairingii) 6 To 10 Hp , Panel Board & Starter Repairingiii) 11 To 15 Hp , Panel Board & Starter Repairingiv)16 To 20 Hp , Panel Board & Starter Repairing V) 21 To 30 Hp , Panel Board & Starter Repairing Vi) 31 To 35 Hp , Panel Board & Starter Repairing Vii) 36 To 40 Hp , Panel Board & Starter Repairing Viii) 41 To 50 Hp. , To Fit Motor As It Isi) 1 To 5 Hp , To Fit Motor As It Isii) 6 To 10 Hp , To Fit Motor As It Is Iii) 11 To 15 Hp , To Fit Motor As It Isiv)16 To 20 Hp , To Fit Motor As It Isv) 21 To 30 Hp , To Fit Motor As It Is Vi) 31 To 35 Hp , To Fit Motor As It Isvii) 36 To 40 Hp , To Fit Motor As It Isviii) 41 To 50 Hp. , X)Bare Motor Spare Parts 10 To 15:Bearing , Air Fan , Shaft , Bearing Plate , Motor Bush , Roter Assembly , Stud Nut Kit , Nut Bolt Kit , X)Bare Motor Spare Parts 6 To 20:Bearing , Air Fan , Shaft , Bearing Plate , Motor Bush , Roter Assembly , Stud Nut Kit , Nut Bolt Kit , X)Bare Motor Spare Parts 21 To 50 :Bearing , Air Fan , Shaft , Bearing Plate , Motor Bush , Roter Assembly , Stud Nut Kit , Nut Bolt Kit , Y)Vaccume Pump Repairing Drive Out Pumpi) 1 To 3 Hp , Y)Vaccume Pump Repairing Drive Out Pump Ii) 4 To 5 Hp , Motor Rewinding I) 1 To 3 Hp , Motor Rewinding Ii) 4 To 5 Hp , Pump Opening, Repairing, Over Oiling, Fitting & Testingi) 1 To 3 Hp , Pump Opening, Repairing, Over Oiling, Fitting & Testingii) 4 To 5 Hp , Roter Shaft Turning & Polishing I) 1 To 3 Hp , Roter Shaft Turning & Polishing Ii) 4 To 5 Hp , To Make Vaccume Pump Bush & Baring Housing I) 1 To 3 Hp , To Make Vaccume Pump Bush & Baring Housing Ii) 4 To 5 Hp , To Fit New Pump Set I) 1 To 3 Hp , To Fit New Pump Set Ii) 4 To 5 Hp , Panel Board & Starter Repairing I) 1 To 3 Hp , Panel Board & Starter Repairing Ii) 4 To 5 Hp , Z) Vaccume Pump Spare Parts 1 To 3 Hp :Baring , Impelor Key , Pump Bush , Air Fan , Sturnut Key , Baring Plate Both Side , Mechanical Seal , Gland Rope , Gland Bush , Gland Plate , Roter Fitted Shaft , Latern Ring , Roter G.M. , Fan Cover , Spacer , Baring Housing , Neck Ring , Port Plate , Flage (Delevery/ Section) , Shaft Sleve , Saction & Delivery Chember , Steter Fitted Motorbody , Tie Rod , Roter Casing , Liquid Diflector , Z) Vaccume Pump Spare Parts4 To 5 Hp :Baring , Impelor Key , Pump Bush , Air Fan , Sturnut Key , Baring Plate Both Side , Mechanical Seal , Gland Rope , Gland Bush , Gland Plate , Roter Fitted Shaft , Latern Ring , Roter G.M. , Fan Cover , Spacer , Baring Housing , Neck Ring , Port Plate , Flage (Delevery/ Section) , Shaft Sleve , Saction & Delivery Chember , Steter Fitted Motorbody , Tie Rod , Roter Casing , Liquid Diflector , Starter Reley I) 6 To 10A. , Ii) 9 To 14 A. , Iii) 13 To 21 A , Iv) 19 To 27 A , V) 21 To 32 A , Starter No Volt & Over Load Coil , Contactor Set Fulli) S. K. -1 , Ii)M.L. -1 , Iii) M.L. -2 , Iv) M.L. -3 , V) M.L. - 4 , Vi) M.L. - 5 , Vii) M.L. - 6 , Viii) M.L. - 7 , Ix) M.L. - 8 , X) M.L. - 9 , Xi) M.L. - 10 , Reley Plate (Kit) , Contactor Point Kiti) S. K. -1 , Ii) M.L. -1 , Iii) M.L. -2 , Iv) M.L. -3 , V) M.L. - 4 , Vi) M.L. - 5 , Vii) M.L. - 6 , Viii) M.L. - 7 , Ix) M.L. - 8 , X) M.L. - 9 , Xi) M.L. - 10 , I) Fuse Grip 16 A. , Ii) Fuse Grip 32 A. , Iii) Fuse Grip 63 A. , Iv) Fuse Grip 100 A , V) Fuse Grip 200 A.. , Fuse Basei) 16 A. , Ii) 32 A. , Iii) 63 A. , Iv) 100 A. , V) 200 A. , Connector Plate , I) Volt Meter 0-440 Volt Small , Ii) Volt Meter 0-440 Volt Big , Ampear Meter , Ampear Meteri) 0 To 15 A. , Ii) 0 To 50 A. , Iii) 0 To 100 A. , Iv) 0 150 A. , Capasitor 1 K.V.A.R. , Single Phasing Preventor , Water Level Guardwith 60 M. Wire , On-Off Rotery Switch , Volt Meter / Ampere Meter Switch , Nuon Indicator Lamp , Main Switch 440 Volt Three Phase , I) 16 A. , Ii) 32 A. , Iv) 100 A. , V) 200 A. , M.S.E.B. Unit I) 32 A. , Ii) 63 A. , Iii) 100 A. , Iv) 200 A. , H.R. C. Fuse I) 100 A. , Ii) 125 A. , Iii) 200 A. , Aquazilary Coil , Timer Coil , C.T. Coil I) 60 A. , Ii) 100 A. , Iii) 200 A. , Tog Tester , Multi Meter , Insulation Tester , Meger , Hand Gloves - 1 Pair (Rubber) , Insulated Rubber Matting , To Arthing With Arthing 300 X 300 X 50 M.M. Arthing Plate,G I. Pipe & Arthing Wire , To Arthing With Arthing 450 X 450 X 50 M.M. Arthing Plate, G I. Pipe & Arthing Wire , Arthing Wire 14 To 6 Guage , Starter D.O.L , I) 1 To 5 Hp , Ii) 5 To 10 Hp , Iii) Star Delta Auto 10 To 20 Hp , Vi) Star Delta Auto 21 To 30 Hp , V) Auto Transfarmer Starter 20 To 30 Hp , Vi) Auto Transfarmer Starter 31 To 50 Hp , Transfarmer Coil Rewinding With Copper Wire In Transfarmer Starter. Without Returning Old Copper Wire. , Change Over Switch 50 A. 3 Phase , Change Over Switch 100 A. 3 Phase , Change Over Switch 200 A. 3 Phase , Buz Bar 30 To 50 Hp , Transfarmer Oil , Discharge With Stainless Steel Pump Shaft And Motor Suitable For Working On 415 V± 10%, 3Ph, 50 Hz., A.C. Supply, Cable Guard, Thrust Carbon/Fibre Bearing To Accept Entire Hydraulic Thrust, Water Proofwinding Shall Be Provided. The Pump Set Shall Be Suitable For Direct Coupling. Pump Shall Have Suitable Suction Stainer Shall Also Be Provided. 3 Core, Single/Double Run Copper Conductor Submersible Type Flat Cable 3 Mtr. And 3 Pairs Of Erection Clamps. Rates Per Pump Upto 20 Stages (As Per Design)Submercsible Pump Set 100Mm Dia(With Polypropelene/ Noryl Impeller)Up To 20 Stages1.5 Hp , 2.0 Hp , 3.0 Hp , 4.0 Hp , 5.0 Hp , Submersible Pump 150 Mm Dia (With Bronze /Stainless(Cf8m) Impeller) Up To 8 Stages 1.5 Hp , 2.0Hp , 3.0Hp , 4.0Hp , 5.0 Hp , 6.0Hp , 7.5 Hp , Submersible Pump 150 Mm Dia (With Bronze /Stainless(Cf8m) Impeller) Up To 12 Stages1hp , 12.5Hp , 15Hp , Submersible Pump 150 Mm Dia (With Bronze /Stainless(Cf8m) Impeller) Up To 15 Stages17.5 Hp , 20 Hp , 22.5 Hp , Submersible Monoblock (With Bronze / Stainless Steel (Cf8m) Impeller ) Horizontal/Vertical -Upto 3 Stages( Motor With Water Lubricated Bearing To Accept Entire Hydraulice Threst ) 3 Hp , 5Hp , 7.5 Hp , 10 Hp , Supplying And Erecting Submersible Pumpset 0.75Kw/ 1Hp With 415V 50 Cycles Ac Supply Suitable For 100Mm Dia Borewell . Suitable For 10 To 50 Lpm Discharge At 70 To 20 M And ( Max Effciency At 52 M. Head 30 Lpm Discharge) & Delivery Pipe Of 32 Mmdiameter With A Neccssary H. Type Clamp As Per Specification No. Wp. Smp , Suppluing And Erecting 3 Core Pvc. Insulated Flat Flexible Submersible Cable With Copper Conductor, Pvc Insulated And Pvc Sheathed 3Core 2.5 Sq.Mm , 3Core 4 Sq.Mm , 3Core 6 Sq.Mm , 3Core 10 Sq.Mm , Providing, Suplying & In Standard Lenghts Mdpe Pipes. Conforming To I.S.O. 4427:1996/With Necessary Jointing Material Like Mechanical Connection I.E. Thread/Insert Joint/Quick Release Coupler Joint/Compresion Fitting Joint Or Flanged Joint. ...............Etc Complete. Pn-16Sdr - 9 20 Mm , 25Mm , 32Mm , 40Mm , 50Mm , 63Mm , 75Mm , 90Mm , Providing, Suplying & In Standard Lenghts Hdpe Pipes. Conforming To I.S.O. 4427:1996/With Necessary Jointing Material Like Mechanical Connection I.E. Thread/Insert Joint/Quick Release Coupler Joint/Compresion Fitting Joint Or Flanged Joint. ...............Etc Complete.6Kg 32Mm , 40Mm , 50Mm , Cpvc Pipe32mm , Cpvc Pipe 40Mm , 50Mm , Providing Isi Mark Gi Pipe With One Coupler Of Following Class And Dia Including All Local And Central Taxces, Octroi, Inspection Charges, Transportation To Stores Etc. Complete. Is 1239/2004 - 15 Mm Dia Medium , 20 Mm Dia Medium , 25 Mm Dia Medium , 32 Mm Dia Medium , 40 Mm Dia Medium , 50 Mm Dia Medium , 65 Mm Dia Medium , 80 Mm Dia Medium , 100 Mm Dia Medium , 125 Mm Dia Medium , 150 Mm Dia Medium , Lowering, Laying, Jointing G.I. Pipes And Specials Of Following Class And Dia. Including Conveyance From Stores To Site Of Works, All Labour, Giving Satisfctory Hydraulic Testing Etc. Complete. Either Underground Or In Vertical Position, As Directed By Engineer-In-Charge.- 15 Mm Dia Medium , 20 Mm Dia Medium , 25 Mm Dia Medium , 32 Mm Dia Medium , 40 Mm Dia Medium , 50 Mm Dia Medium , 65 Mm Dia Medium , 80 Mm Dia Medium , 100 Mm Dia Medium , 125 Mm Dia Medium , 150 Mm Dia Medium , Providing, Supplying Isi Mark C.I.D/F. Reflux Valve (Non Return Valve ) With Jointing To Pipe Work(Including All Hardware And Packing) Water Works Quality With Jointing To Pipe Withoutbypass Arrangement With Gunmetal Seat Excluding C.C. Foundation/Structural Steel Supports. For Rating Pn - 1.6 Confirming To Is - 5312: 1984 - 50 Mm Dia , 65 Mm Dia , 80 Mm Dia , Lowering, Laying And Jointingin Position Following Cidf Reflux Valve/ Butterfly Valve And Sluice Valve Including Cast Of All Labour, Jointing Material Including Nut Bolts And Giving -50 Mm Dia , 65 Mm Dia , 80 Mm Dia , Nrv Valve Gun Metal 25 Mm , Nrv Valve Gun Metal 80 Mm , Providing And Supplying Isi Standard C.I. Flanged / S & S Specials Including All Taxes (Central And Local) Railway Freight, Insurance, Unloading From Railway Wagon, Loading Into Truck, D.F.Specials80 Mm To 300 Mm Dia , Supplying And Erecting Automatic Control Panel For 3Ph,415V ,Ac Submersible /Centrifugal Pumpset Upto 6 Hp Consisting Of Dol Starter Having Relay Range 9-14 Amp S.P.P.,Combined Ammeter/Voltmeter, Phase Indicating Lamp Enclosed In Crca Powder Coated Vibration Proof Encloser With Ip 54 Protection Control Panel Should Offer Single Phase ,Phase Reversal ,Phase Inbalance Etc ( Similer To Lt Model No.Mu G6/Cat No.Ss97756) , Dol Starter- Supplying And Erecting Dol Starter To Operate Squirrel Cage Induction Motor Working On 380 - 440 V, 3 Ph., 50 Hz., With No Volt Coil, Overload Element With Necessary Material & Connected To Supply Etc. Comp. Starter With Original Sheet Steel Encloser. - Up To 7.5 Hp , Up To 10 Hp , Main Switch 415V -16A , Main Switch 415V- 32A , Main Switch415v-63A , S.S. Nipple , Dual Chamber/Special Water Chamber , Providing Structural Steel Work In Single Stanctions Composed Of Rsj Chanel Etc. With Caps, Bases, Mild Steel Plates Angles, Bracket Cleats, Gusset Plates, Anchour Bolts Etc. As Per Detailed Drawing And Design Or As Directed By Engineer-In-Charge Including Cutting, Fabricating, Hoisting, Erecting, Fixing, In Position Making Reveted/Bolted/Welded In Connection And One Coat Of Anti Corrosive Point And Over It Two Coats Of Oil Painting Etc. Complete.-7.5 Hpto 12.5H.P. , Above12.5 Hpto20h.P. , Above 20 Hpto25h.P. , Above 25 Hpto40h.P. , Providing Structural Steel Work In Single Stanctions Composed Of Rsj Chanel Etc. With Caps, Bases, Mild Steel Plates Angles, Bracket Cleats, Gusset Plates, Anchour Bolts Etc. As Per Detailed Drawing And Design Or As Directed By Engineer-In-Charge Including Cutting, Fabricating, Hoisting, Erecting, Fixing, In Position Making Reveted/Bolted/Welded In Connection And One Coat Of Anti Corrosive Point And Over It Two Coats Of Oil Painting Etc. Complete. , Earthing For Pumping Machinery Supplying And Erecting Earthing With Galvanised Cast Iron Earth Plate Size 60X60x0.6 Cm Complete With All Materials,Testing &Recording The Result As Per Specification No.Ea-Ep , Excavation For Foundation / Pipe Trenches In Earth, Soil Of All Types, Sand, Gravel And Soft Murum, Including Removing The Excavatedmaterial Upto A Distance Of 50 Metres And Lifts As Below, Stacking And Spreading As Directed, Normal Dewatering, Preparing The Bed For Foundation And Excluding Back Filling, Etc. Complete. Lift 0-1.5 M. , Excavation For Foundation / Pipe Trenches In Hard Murum, Including Removing The Excavatedmaterial Upto A Distance Of 50 Metres And Lifts As Below, Stacking And Spreading As Directed, Lift 0-1.5 M. , Providing And Supplying In Standard Lengths Isi Mark Rigid Unplasticised Pvc Pipes Suitable For Potable Water With Unplastised Pvc Pipes Suitable For Potable Water With Solvent Cement Joints Including Cost Of Couplers, As Per Is Specification No. 4985 / 1988 Including All Local And Central Taxes, Transportation, Freight Charges, Inspection Charges, Loading, Unloading, Conveyance To The Departmental Stores/ Site And Stacking The Same In Closed Shed Duly Protected From Sun Rays And Rains Including Cost Of Jointing Material I.E. Solvent Cement, Etc.Complete (Selffit Type To Be Jointed With Cement Solvent).-63 Mm Dia. Pvc 4 Kg/ Cm² , 75 Mm Dia. Pvc 4 Kg/ Cm² , 90 Mm Dia. Pvc 4 Kg/ Cm² , 110 Mm Dia. Pvc 4 Kg/ Cm² , 140 Mm Dia. Pvc 4 Kg/ Cm² , Lowering, Laying And Jointing Pvc Pipes And Specials Of Following Class And Diameter Including Cost Of Conveyance From Stores To Site Of Work Including Cost Of All Labour, Material, Except Cement Solvent, Rubber Ring, Giving Satisfactory Hydraulic Testing As Per Is Code, Etc. Complete (With Cement Solvent Joint / Ring Fit Joint)-63 Mm Dia. Pvc 4 Kg/ Cm². , 75 Mm Dia. Pvc 4 Kg/ Cm² , 90 Mm Dia. Pvc 4 Kg/ Cm² , 110 Mm Dia. Pvc 4 Kg/ Cm² , 140 Mm Dia. Pvc 4 Kg/ Cm² , Providing And Laying In Citu C.C. Of Of Trap / Granite/ Quartzite/Gneiss Metal For Foundation And Bedding Including Normal Dewatering, Formwork, Compacting And Curing, Finishing, Etc.Complete. Pcc M -100 For Reinstaining Of Cement Road , Providing And Constructing Two Taps Standpost As Per Type Design With Excavation 15 Cm Thick Pcc (1:3:6) Bedding 20 Mm Thick Pcc (1:2:4) Concrete For Platform Of 1.75 M Dia. With Side Curb And Bucket Rest 80 Mm Dia, Heavy Duty Gi Pipe Central Post Duly Filled Therein With C.C. (1:2:4) 5 M Long, 20 Mm Dia. Medium G.I. Pipe From Point Of Tapping To Standpost Additional 20 Mm Dia G.I. Pipe Fixed Verticaly Upto 15 Mm Dia Self Closing Water Taps On Brass Ferrule Etc. Complete Together With All Labour And Material Charges As Per Drawing And As Directed By Engineer-In-Charge When Good Foundation Is Available. Rate Includes Draining Arrangement By Excavating Open Gutters. , Refilling The Trenches With Available Excavated Stuff With Soft Material First Over Pipeline And Then Hard Material In 15 Cm Layers With All Leads And Lifts Including Consolidation, , Providing,Hosting And Fixing In Position Of Approved Make High Density Polyethylene Uv Stabilized Conforming To Is 12701 ,Water Storage Tank With Necessary Connections, Testinfg Etccomplete 9 Prior Approval Of Sample By Ex. Engineer Is Necessary Before Use ) Spect. No. As Directed By Engineer In Charg.For 200 To 1000 Lit. , For 1000 To 20000 Lit. , Providing Fixing 15Mm Dia Screw Down Bib Stop Tap Of Brass Including Necessory Socket Union Nut Complete (Pwd Csr 22-23 P.No. 288 I.No. 41.4 , Providing And Laying In Trenches Dia Cpvc Pipeincluding Necessary Excavation Fitting Reffilling Trenches Etc Complete Including Removing Existing Pipe Line If The Same In Pwd Chowky Or As Directed Etc Complete 1)For --15 Mm Dia , 2) For 20 Mm Dia , 3) For 25 Mm Dia , 4) For 32 Mm Dia , 5) For 40 Mm Dia