Construction Of C.C Interlocking Block Teen Shade Rcc Chair From Gujar Shamshan In Ward No.03
Tender Value
16.26 Lakhs
Estimated cost
Bid Submission
01 May 2023
0 days left
EMD
32529
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
didwana → Rajasthan
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of C.C Interlocking Block Teen Shade Rcc Chair From Gujar Shamshan In Ward No.03
BOQ
| Sl. No. | Item Description |
| 1 | Construction of embankment with approved material obtained fromborrow pit with all lifts and leads, transporting to site, spreading,grading to required slope and compacting by vibratory roller 8-10tonne to meet requirement of table 300-2 including cost ofcompensation for earth taken from private land complete as perMoRT&H specification clause 305. (Lead taken upto 5 km) |
| 2 | Earth work in excavation in foundation, trenches etc. including dressing of sides and ramming of bottoms, including getting out the excavated material, refilling after laying pipe/ foundation and disposal of surplus excavated material at a lead upto 50m suitable site as per direction of Engineer for following depths, below natural ground / Road top levelDepth upto 1.5 m |
| 3 | Carriage Of Material Earth, Sand, Lime, Morrum manure or sludge up to 2 km |
| 4 | Providing and laying granular sub-base material having P.I.not more than 6, including compacted thickness and consolidation by 8-10 tonne power roller at OMC to achieve desired density to required camber and grade including cost of water and hire charges of machinery, including T&P and all lead of material from quarry (compacted thickness to be measured). Grading as per MoRTH specification : Table 400-1,400-2 with CBR value not less than 15 ii)To achieve 95% Proctor densityGrading as per MoRTH specification : Table 400-1,400-2 with CBR value not less than 20 To achieve 95% Proctor density |
| 5 | Providing and laying lean cement concrete 1:4:8 in Sub- base over aprepared sub-grade with coarse and fine aggregate conforming toIS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate radationafter blending to be as per table 600-1, cement content not to beless than 150 kg/ cum, optimum moisture content to be determinedduring trial length construction, concrete strength not to be less than10 Mpa at 7 days, mixed in a batching plant, transported to site, laidwith a paver with electronic sensor, ompacting with 8-10 tonnesvibratory roller, finishing and curing complete as per clause 601, 112of MoRT&H specification including all material, labour, hinery, lighting, guarding and maintenance of diversion. |
| 6 | Providing and fixing of precast concrete interlocking tiles of desiredshape of M 30 grade manufactured from fully computerizedautomatic stationery hydraulic viebro pressed machine and fullycomputerized automatic batching plant of class A1/A2 as per BS6717:2001. The CC interlocking paving blocks be laid on average50mm. thick bed of coarse sand and the joint is to be filled with finesand. Laying procedure on compacted sub-base as defined.Complete job is to be executed as per the instruction of Engineerincharge. The rates to be inclusive of all lead & Lifts etc. complete asper specifications. Tensile splitting strength, abrasion and brakingload etc. as per BS 6717:2001, Grey cement. 80mm thick |
| 7 | Brick work with machine moulded perforated bricks of classdesignation 125 conforming to IS: 2222 -1991 in superstructure above plinth level upto two stories in cement mortar 1:6 (1 cement : 6 coarse sand) : With Modular bricks. |
| 8 | Cement plastering including T&P, scaffolding, material and completelabpour, including cost of water, curing, racking of joints etc. with 20mm cement plaster of mix :1:6 (1 cement : 6 fine/ coarse sand) |
| 9 | Supplying, erecting and fixing in position specified precast RCCbench made of RCC grade M-30 consisting of 2 Nos. “L” shapedbase support of thickness 100 mm back height 1000mm, front height450 mm, base width 420mm and 5 Nos. RCC planks of size of1500x100 x 50 mm and 1 Nos RCC planks of 150x200x50mmincluding joining all parts with galvanised nuts and bolts of suitablesize. All bolts to be sealed after assembly with nice finish andappearance and level complete in all respect as per direction ofengineer in charge. Every bench should have a manufacture‘s logoof appropriate size Engraved at suitable place. |
| 10 | Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. |
| 11 | Providing corrugated G.S. sheet roofing including vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steelprimer and two coats of approved paint on overlapping of sheetscomplete upto any pitch in horizontal/ vertical or curved surfaces)excluding the cost of purlins, rafters and trusses and including0.63 mm thick with zinc coating not less than 275gm/m²cutting to size and shape wherever required |
AI Tender Summary
Tender Timeline
Apr 22, 2023
11:30 IST
Tender Published
Tender notice published.
CompletedMay 01, 2023
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedMay 03, 2023
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender