Tender For Renovation Of Staff Quarter Situated At Community Health Centerichak Block- Ichak
Tender Value
72.05 Lakhs
Estimated cost
Bid Submission
24 Apr 2023
0 days left
EMD
1.45 Lakhs
Bank guarantee accepted
Document Fee
10000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
ichak → Jharkhand
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Renovation Of Staff Quarter Situated At Community Health Centerichak Block- Ichak
BOQ
| Sl. No. | Item Description |
| 1 | Labour for cleaning outer, inner, roof of building all complete job. |
| 2 | Dismantling old plaster and pointing in cement or lime and raking out joints to 15mm depth, watering and disposal of unserviceable materials with all leads all complete as per specification and direction of E/I. |
| 3 | Providing 12 mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding, taxes androyalty all complete as per specification and direcition of E/l. |
| 4 | Providing 6mm cement plaster (1:4) in ceiling with clean coarse sand of F.M 1.5 including cost of screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I. |
| 5 | Waterproofing for Old and New RoofSlab :-Providingandlaying waterproofing treatment onroof slabby applyingtwo Component,factory designed, ready to use, acrylic modifiedflexible material applied with brush, roller or spray for water proofing coating as per manufacturer specifications with 5 steps. Brand - Sika_Plastocrate plus, MYK proof WP10, Fosroc- Conplast X421 ic Dr. Fixit Pidiproof LW+. |
| 6 | Covering of treated surface with PCC :- Providing 25 mm thick Cement Concrete M20 (1:1.5:3) maintaining slope inalternate 2 mt x 2 mt panels with aaproved quality of stone chips of 20 mm to 6mm size graded and clean sand of F.M. 2.5 to 3 including screening, shuttering and mixing cement concrete in mixer with admixture of integral water proofing and placing in position, striking, curing, taxes and royaltyall complete as per building specification and direction of E/I. Panels that has been left should be casted next day. There should be 6mm gap between panels. Brand - Sika_Plastocrate plus, MYK proof WP10, Fosroc- Conplast X421 ic Dr. Fixit Pidiproof LW+. |
| 7 | Providing and filling of 6 mm thick Groove between 25 mm PCC Panels with Polysulphide Sealant(Poring Grade)as per drawings and technical specifications and direction of E/I. (with 18% GST) Brand - Sika_Plastocrate plus, MYK proof WP10, Fosroc- Conplast X421 ic Dr. Fixit Pidiproof LW+. |
| 8 | Reinforcedcementconcreteworkinbeams,suspendedfloors,roofshaving slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III): 3 graded stone aggregate 20 mm nominal size). |
| 9 | Centering and shuttering including strutting, propping etc. and removal of form for Weather shade, Chajjas, corbels etc., including edges |
| 10 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 11 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item) : With float glass panes of 5.0 mm thickness |
| 12 | Supplying fitting and fixing M S Grill made of 20 x6 cmm MS flat as per approved design and drawing property fabricated with joints continuous fillet welded and finished smooth.Carriage of grill to work site as per building specification and direction of E/I |
| 13 | Supplying, fitting and fixing 35mm thick solid core type non-decorative single leaf flush door shutter in door and windowswith black board core blended with high qualityphenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I. |
| 14 | Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-chargeFixing with adjustable lugs with split end tail toeach jamb |
| 15 | Providing 150mm wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 125mm apron including cost of eartwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I. |
| 16 | Providing designation 75 B brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 17 | Providing and laying Doublecharge vitrified floor tiles in different sizes(thickness to be specified by the manufacturer) with water absorptionless than 0.08% and conforming to IS: 15622 / ISO 13006 of approvedmake, in all colours and shades, laid on 20mm thick cement mortar 1:4(1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm . |
| 18 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated andgroutedwithfinesand,includingnecessaryexcavation,levelling& dressing & finishing the top smooth |
| 19 | Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over theprimer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc, and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 650/ 450N/ 5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane : 3 mm thick |
| 20 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter |
| 21 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete |
| 22 | Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty where required, scaffolding , washing of floors and taxes all complete as per specification and direction of E/I. |
| 23 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm). |
| 24 | Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direction of E/I. |
| 25 | Earth work in excavation in foundation trenches in ordinary soil (vide classification of soil itemA) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I. |
| 26 | Supply of fine agreegate/stone dust -do- -do- all complete job. |
| 27 | Labour for compaction -do- -do- all complete job. |
| 28 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size) |
| 29 | Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer\"s specifications & direction of Engineerin-Charge.80mm thick Cement concrete paver block of M-30 grade with approvedcolour, design & pattern. |
| 30 | Supplying, fining and fixing viterous white glazed earthen ware I.W.C of Parry Hindustan or any other I.S.S approved make with 100mm H.C.I \"p\" trap 15 liters C.I. or C. pull and let go flushing cisternofnames or other I.S.S equivalent make, complete with all fittings. C.I or C.Cbrackets 32mm alkathene/P.V.C telescopic flush, pipe about 2M long with one brass coupling and clamps G.I chain and pull includingsupplyingand fixing a pair of viterous white glazed earthenware where footrest to be fixed in floor 15 mm C.I body brass spindle stope cock of weight not less than 50 grins. 15 mm P.V.C connection pipe 450mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I.580mm long with 10 litre low level P.V.C. cistern |
| 31 | Supplying, fitting and fixing flat back or angular, lipped front viterous white glazed earthen ware Urinal of Parry Hindustan or any other I.S.S approved make with 5 liters capacity C.I. outomatic flushing cistern ofReliance or other I.S.S approved make with all fittings with C.I or R.S. brackets, standard size G.I. flush pipe with fitting clamps, 15 mm C.I body brass spindle stop cock of approved quality weight not less than 400 grams, 15 mm P.V.C./Alkethene pipe 450mm long with brass coupling at both ends and doing plumber joints including painting of exposed part with two coats of approved paint over a primer coat of red oxide, cutting wall and floor, making good the same etc. all complete as per specification and direction of E/I.Standing corner (600mm x 350mm) |
| 32 | Supplying, fitting and fixing wash basin with C.I. or M.S. brackets 15mm C.P. brass pillar tap Kingston/Gem/Techno/Ponco 2mm C.P. brass waste of standard pattern including painting and fitting of brackets, cutting and making good the wall wherever required - Flat back wash basin size 550 x 400mm with single 15mm C.P. brass pillar tap all complete as per specification and direction of E/I. |
| 33 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 20mm dia - |
| 34 | 32mm dia - |
| 35 | Providing and fixing male ended 15mm dia brass bib cock of approved quality (wt. not less than 350 gms.) with extra socket all complete as per specification and direction of E/I. |
| 36 | Providing and fixing brass/C.I. stop cock of approved quality as per specification and direction of E/I. Brass stop cock - 15mm dia |
| 37 | Supplying, fitting and fixing of following item complete with all materials etc. all complete as per specification and direction of E/I. (a) Mirror of 4mm thick plain glass bottled edge(450 x 300mm) - |
| 38 | (b) C.P. brass towel rail (20 x 600mm) - |
| 39 | (c) C.P. brass liquid shop container - |
| 40 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single tee without door - 110x110x110 mm |
| 41 | Bend 87.5° - 110 mm bend |
| 42 | Shoe (Plain) - 110mm |
| 43 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank |
| 44 | Wiring for light point/ fan point / exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, with modular switch, modular plate, suitable GI box etc as required. Group A |
| 45 | Group B |
| 46 | Supplying and fixing suitable size G.I. box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings). |
| 47 | Wiring for circuit / submain wiring alongwith earth wire with the following sizesofFRPVCinsulatedcopperconductor,singlecorecablein surface/ recessed PVC conduit as required 2x1.5sq mm + 1x1.5 sq mm earth wire |
| 48 | 2x2.5sq mm + 1x2.5 sq mm earth wire |
| 49 | 2 x 4.0 sq. mm + 1 x 4.0 sq. mm earth wire |
| 50 | Supplying andfixing offollowing sizes ofPVCconduit alongwith the accessoriesinsurface/recessincludingcuttingthewallandmakinggood the same in case of recessed conduit as required. 20mm dia |
| 51 | 25mm dia |
| 52 | Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required. 75mm x 75mm x 50mm |
| 53 | 121mm x 173mm x 48mm |
| 54 | 170mm x 221mm x 48mm |
| 55 | 210mm x 206mm x 48mm |
| 56 | Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box / wooden block including connection etc. as required. |
| 57 | Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable etc. as required. |
| 58 | Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 59 | Supplying and fixing brass batten / angle holder including connection etc. as required. |
| 60 | XLPE indulated PVC sheathed, heavy duty, armoured elecical cable with aluminium conductor for working voltage upto and including 1100 volts. (Conforms to IS : 7098, Part - 1) |
| 61 | Supplying 15/16 Watt LED bulb of approved make. |
| 62 | Supplying ceiling fan of 48\" (1200mm) dia of approved make. |
| 63 | Providing and fixing T5 1 x 28 W box type fixture with tube |
| 64 | Earth work in excavation in foundation trenches in hard soil (vide classification of soil item-A+B) and disposal of excavated earth as obtained to a distance up to 50M including all lifts with leveling, ramming the foundation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/I. |
| 65 | Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labours, royaly and taxes all complete as per building specification and direction of E/l. |
| 66 | Providing designation 75B one brick flat soling joints filled with local sand including cost of watering taxes, royalty all complete as per building specification and direction of E/I. |
| 67 | Providiag designation 75B brick work in Cement Mortar (1:6) in foudation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing taxes and royalty all complete job as per building specificition and direction of E/l. |
| 68 | Providiag 125mm thick reinforced designation 75A brick work in Cement Mortar (1:4) in super structure with approved quality of clean coarse sand of F.M. 2 including providing 10mm thick mortar joint, cost of screening materials, raking out joints to 15mm depth, curing taxes and royalty all complete job as per building specificition and direction of E/l. |
| 69 | Reinforcedcementconcreteworkinbeams,suspendedfloors,roofshaving slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III): 3 graded stone aggregate 20 mm nominal size). |
| 70 | Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete. |
| 71 | Providing 12 mm thick cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 1.5mm cement punning including screening, curing with all leads and lifts of water, scaffolding, taxes androyalty all complete as per specification and direcition of E/l. |
| 72 | Providing TMT steel reinforcement 10mm, 12mm & 16mm dia bars as per approved design and drawing excluding carriage of M.S bar to work site, cutting, bending end binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per building specification and direction of E/I. 8mm dia bar - |
| 73 | 10mm dia bar - |
| 74 | 12 mm Dia. & Above Bar- |
| 75 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 76 | (i) Cement |
| 77 | (ii) Sand |
| 78 | (iii) Bricks |
| 79 | (iv) Steel |
| 80 | (v) Stone Chips |
| 81 | (vi) Stone Dust |
| 82 | Goods & Services Tax (G.S.T.) - 18% |
| 83 | Labour Cess - 1% |
AI Tender Summary
Tender Timeline
Apr 15, 2023
11:30 IST
Tender Published
Tender notice published.
CompletedApr 24, 2023
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedApr 26, 2023
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender