Tender For Establishment Of Pisciculture Knowledge Centre Under Gournagar Rd Block Under Kailashahar Sub-Division
Tender Value
43.78 Lakhs
Estimated cost
Bid Submission
26 Apr 2023
0 days left
EMD
87563
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
gournagar → Tripura
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Establishment Of Pisciculture Knowledge Centre Under Gournagar Rd Block Under Kailashahar Sub-Division
BOQ
| Sl. No. | Item Description |
| 1 | Item Description |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.All kinds of soil. By manual means |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. All kinds of soil |
| 4 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete. |
| 5 | Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/Lindane emulsifiable concentrate of 20% |
| 6 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment as per IS:6313 (Part III)-Latest revision (excluding the cost of chemical emulsion): Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres/sqm of the vertical surface of the substructure to a depth of 300 mm including excavation channel along the wall & rodding etc. completeWith Chlorpyriphos/Lindane E.C. 20% with 1% concentration. |
| 7 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering. All work upto plinth level. 1:2:4 ( 1 Cement: 3 fine sand : 6 graded stone aggregate 40 mm nominal size) |
| 8 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering. All work upto plinth level. 1:3:6 ( 1 Cement: 3 fine sand : 6 graded stone aggregate 40 mm nominal size) |
| 9 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering. All work upto plinth level. 1:4:8 ( 1 Cement: 4 fine sand : 8 graded stone aggregate 40 mm nominal size) |
| 10 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering. All work upto plinth level. 1:5:10 ( 1 Cement: 5 fine sand : 10 graded stone aggregate 40 mm nominal size) |
| 11 | Providing and laying damp-proof course with cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 12.5mm/20mm nominal size). D.P.C. 40 mm thick |
| 12 | Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer\"s specification. |
| 13 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 fine sand : 6 graded well burnt brick aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth |
| 14 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement. All work upto plinth level. 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 15 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and skirting courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement-. In plinth and skirting courses, fillets, columns, pillars, posts and struts. 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 16 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement-. RCC work in suspended floors, roofs having slope upto 15° landings, balconies, shelves and chajjas. 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 17 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement-.RCC work in beams, lintels, bands, plain window sills, staircases and spiral staircases excluding precast spiral staircase.1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 18 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto floor five level. Thermo-Mechanically Treated bars/ Cold twisted deformed steel bars |
| 19 | Centering shuttering including struttings, propping etc. and removal of form work for: Foundations, footings, bases for columns etc. for mass concrete with timber plank |
| 20 | Centering shuttering including struttings, propping etc. and removal of form work for:Suspended floors, roofs, landings, balconies and access platform with timber planks |
| 21 | Centering shuttering including struttings, propping etc. and removal of form work for:Lintels, beams, plinth beams, girders, bressumers and cantilevers with wooden plank |
| 22 | Centering shuttering including struttings, propping etc. and removal of form work for:Columns, Pillars, Piers, Abutments, Posts and Struts with wooden plank |
| 23 | Centering shuttering including struttings, propping etc. and removal of form work for:Stairs (excluding landings) except spiral-staircases with wooden plank |
| 24 | Centering shuttering including struttings, propping etc. and removal of form work for:Weather shade, Chajjas, corbels etc., including edges. |
| 25 | First class brick work in foundation and plinth including cost of all materials as required complete: In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 26 | Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 27 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position: Sal wood |
| 28 | Providing and fixing panelled/or panelled and glazed shutters for doors, windows and clerestory windows includingISI marked bright finished/black enamelled M.S butt hinges with necessary screws excluding panelling and or glazing, which will be paid for separately but including the wooden beading of 20×12 mm for fixing panelling and or glazing as per direction of Engineer-In-Charge. Gamair Wood. 35 mm thick shutters |
| 29 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete. Fixed to openings /wooden frames with rawl plugs screws etc. |
| 30 | Providing 40 × 5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30 × 10 × 15 cm 1:3:6 mix (1 cement : 3 fine sand : 6 graded stone aggregate 20mm nominal size) |
| 31 | providing and fixing ISI : 1341 marked M.S heavyweight butt hinges with necessary screws etc.complete :125 × 90× 4.0 |
| 32 | Providing and fixing IS:3564 marked Aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc. complete. |
| 33 | Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete:300x16 mm |
| 34 | Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete:250x16 mm |
| 35 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS:1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete: 300x10 mm |
| 36 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS:1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete: 250x10 mm |
| 37 | Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc. complete: 125 mm |
| 38 | Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc. complete: 100 mm |
| 39 | Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Single rubber stopper |
| 40 | Providing and fixing factory made door frame (single rebate) made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 60mm width & 30mm thickness and shall be fixed to wall as per instructions of Engineer-In-Charge using 100x8 sheet metal CSK screws |
| 41 | Providing and fixing 28 mm thick door shutter made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 71mm width & 28mm thick as vertical & horizontal styles. Joints are made using solventadhesive and GI ‘C sections (39mm x 19mm x 0.6mm thick) or M S pipe (40mm x 20mm ) stiffener frame insert & telescopic polymeric ‘L’ corners .The panel shall be filled with 3mm thick high - pressure compact laminate as per manufacturer’s specifications and directions of the Engineer-in-charge, cover moulding shall be provided for covering fixing screws and elegant look.( for W.C. bathroom door shutter). |
| 42 | Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm at 100 mm centre to centre and braced with flat iron diagonals 20x5mm size with top and bottom rail of T-iron 40x40x6mm with 40mm dia. steel pulleys& with riveted bolts, nuts, locking arrangement, stoppers, handles, hold fast /anchor bolt including embedding in cement concrete of required grade for fixing in position, all necessary fittings,including applying a priming coat of approved steel primer etc. complete as required. |
| 43 | Providing and fixingfan clamp type-Iof 16 mm dia M.S. bar bent to shape with hooked ends in R.C.C. slabs during laying including painting the exposed portion of loop, all as per standard design complete |
| 44 | Providing and fixing hand rail using structural steel etc. of approved size by welding etc. to steel ladder railing, balcony railing and staircase railing etc. including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer complete as required: E.R.Wtubes. |
| 45 | Providing and fixing Marble stonein floors over 20 mm thick bed ofcement mortar 1:4 (1 cement:4 fine sand ) jointed with ordinary cement slurry including pointing with white cement mixed with of matching shade, including rubbing and polishingcomplete. 18 mm thick Marble stone: Agaria White marble |
| 46 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer) of approved make in all colours, shadesof any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 (1 cement:3 fine sand) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade complete. |
| 47 | Providing and laying 1st quality ceramic glazed floor tiles of approved size conforming to IS:15622 (thickness to be specified by the manufacturer) of approved make in colours, shades as approved by Engineer-in-charge over 20 mm thick bed of cement mortar 1:4 (1 cement:4 fine sand) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade complete. Ceramic Glazed Tiles 1st quality 300 x 300mm in all shades and designs |
| 48 | Providing and laying polished vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08 % and conforming to IS:15622of approved make in all colours, shades over 20 mm thick bed of cement mortar 1:4 (1 cement:4 fine sand) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade complete.Size of tile 80x80 cm |
| 49 | Providing and fixing 25 mm thick pre-polished colored concrete designer tiles making by strong vibratory compaction technology using 50% white cement and 50% ordinary cement of size 300mm x 300mm, laid in footpath & courtyard, on 20 mm thick bed ofcement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc.complete as per direction of the Engineer-in-charge. |
| 50 | Providing and fixing on wall face unplasticised Rigid PVC rainwater pipes (working pressure 4 kg/cm2) conforming to IS:13592 Type A including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermal expansion: Single socketed pipe - 110 mm OD |
| 51 | Providing and fixing on wall face unplasticised-PVC mouldedfittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermalexpansion: Coupler: 110mm |
| 52 | Providing and fixing on wall face unplasticised-PVC mouldedfittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermalexpansion: Single equal tee without door:110 x 110 x 110 mm |
| 53 | Providing and fixing on wall face unplasticised-PVC mouldedfittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermalexpansion: Single equal tee with door: 110 x 110 x 110 mm |
| 54 | Providing and fixing on wall face unplasticised-PVC mouldedfittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermalexpansion: Bend 87.5 degree:110mm |
| 55 | Providing and fixing on wall face unplasticised-PVC mouldedfittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermalexpansion: Plain shoe:110 mm |
| 56 | Providing and fixing unplasticised-PVC pipe clips of approved design to unplasticised-PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws ofrequired length including cutting brick work and fixing with cement mortar 1:4 (1cement:4 fine sand) making good the wall etc. complete. :110mm |
| 57 | Providing and fixing to the inlet mouth of rain water pipe PTMT grating with thickness of 8mm and weighing not less than 100gm. complete. :100mm |
| 58 | 12 mm cement plaster of mix:In cement mortar 1 : 4 ( 1 cement : 4 fine sand ) |
| 59 | 12 mm cement plaster of mix: In cement mortar 1 : 6 ( 1 cement : 6 fine sand ) |
| 60 | 15 mm cement plaster on the rough side of single or half brick wall of mix: In cement mortar 1 : 6 ( 1 cement : 6 fine sand ) |
| 61 | 6 mm cement plaster of mix: In cement mortar 1 : 3 ( 1 cement : 3 fine sand ) |
| 62 | Neat cement punning. |
| 63 | Distempering with oil bound washable distemper of approved brand and manufacture and of required shade on new work ( two or more coats), over and including water thinnable priming coatto give an even shade.[Payment shall be made after submission of Test Certificate issued by the Manufacturer] |
| 64 | Finishing walls with premium acrylic smooth exterior paint of required shade of approved brand and manufacture on new work (two or more coats applied @ 1.43 litre/10 sqm) over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm complete. [Payment shall be made after submission of Test Certificate issued by the Manufacturer] |
| 65 | Applying priming coat: [Payment shall be made after submission of Test Certificate issued by the Manufacturer]: With ready mixed pink primer of approved brand and manufacture on wood work ( hard & soft wood ). |
| 66 | Painting on G.S. sheet with synthetic enamel paint ( two or more coats ) of approved brand and manufacture of required colour to give an even shade on new work including a coat of appropriate steel primer but excluding a coat of mordant solution complete. |
| 67 | Providing and fixing aluminium work for doors, windows,ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sectionsofapproved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/paneling, C.P. brass/stainless steel screws, all complete as per architectural drawing and the direction of Engineerincharge. (Glazingand paneling and dash fasteners to be paid for separately): For fixed portion of approved quality:- Anodised aluminium (anodised transparent or dyed to requiredshade according to IS:1868, Minimum anodic coating of grade AC15) |
| 68 | For shutters/ sliding shutters of doors, windows & ventilatorsincluding providing and fixing hinges / pivots / rollers and making provision for fixing fittings wherever required including the cost of PVC / neoprene gasket required of approved quality ( Fittings shall be paid for separately ):- Anodisedaluminium(anodisedtransparentordyedto requiredshadeaccordingtoIS:1868,Minimumanodic coating of grade AC 15). |
| 69 | Providing and fixing glazing of approved quality in aluminium doors,windows, ventilator, shutters and partition etc. with EPDM rubber/neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge (Cost of snap beading shall be paid in basic item): With glass/ float glass panes of 5.5 m thickness ( weight not less than 13.50 kg / sqm ) |
| 70 | Grading of roof for water proofing treatment [Payment shall be made after submission of the product performance shall carry guaranted for 7 years against any leakage] complete as required as per direction of the Engineer-in-charge with:Cement concrete 1:2:4 ( 1 cement : 2 fine sand : 4 graded stone aggregate 20 mm nominal size ). |
| 71 | Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100mm sand cast Iron P or S trap,10 litre low level white P.V.C. flushing cistern with manually controlleddevice (handle lever) conforming to IS:7231,with all fittings and fixtures complete including cutting and making good the walls and floors wherever required:White Vitreous china Orrisa pattern W.C. pan of size 580x440 mm with integral type foot rests. |
| 72 | Providing and fixing white vitreous china pedestal type water closet (European type W.C.pan) with seat and lid,10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid |
| 73 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265 mm sizes respectively. |
| 74 | Providing and fixing white vitreous china squatting plate urinal with integral rim longitudinal flush pipe. |
| 75 | Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings:Flat back wash basin of size 550x400mm. |
| 76 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe: 32 mm dia |
| 77 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia |
| 78 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 79 | Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc. complete. |
| 80 | Providing and fixing M.S.holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1 cement:2 coarse sand:4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc.: For 100 mm dia. Pipe |
| 81 | Providing and fixing heel rest sanitary bend: 100 mm dia. Sand cast iron S&S as per IS - 1729 |
| 82 | Providing and fixing double equal plain junction of required degree. 100x100x100x100 mm. Sand cast iron S&S as per IS - 1729 |
| 83 | Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.: 100x100x100 mm. Sand cast iron S&S as per IS - 1729 |
| 84 | Providing and fixing terminal guard: 100 mm: Sand cast iron S&S as per IS - 1729 |
| 85 | Providing and fixing collar: 100 mm: Sand cast iron S&S as per IS - 1729 |
| 86 | Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter: 100mm |
| 87 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors: 100 mm inlet and 100 mm outlet. Sand cast iron S&S as per IS: 3989. |
| 88 | Cutting chases in brick masonry walls for following diameter sand cast iron/centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 (1 cement:3 coarse sand:6 graded stone aggregate 12.5 mm nominal size) including necessary plaster and pointing in cement mortar 1:4(1cement:4 coarse sand): 100mmdia. |
| 89 | Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colours weighing not less than 105 gms |
| 90 | Providing and fixing PTMT towel ring trapezoidal shape 215mm long, 200mm wide with a minimum distances of 37mm from wall face with concealed fittings arrangement of approved quality and colours weighing not less than 80 gms |
| 91 | 15 mm nominal bore, 80 mm long. 42 mm high and 30 mm wide with BSP female threads weighing not less than 48 gms |
| 92 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Inernal work - Exposed on wall. 25 mm dia. nominal bore |
| 93 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Inernal work - Exposed on wall. 40 mm dia. nominal bore |
| 94 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25 to 40 mm nominal bore |
| 95 | Providing and fixing brass bib cock of approved quality : 15 mm nominal bore |
| 96 | Providing and fixing brass stop cock of approved quality : 15 mm dia nominal bore |
| 97 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): 25 mm nominal bore |
| 98 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): 40 mm nominal bore |
| 99 | Providing and fixing gun metal non-return valve of approved quality (screwed end): 40 mm nominal bore. Vertical |
| 100 | Constructing masonry Chamber 30x30x50 cm, inside in brick work in cement mortar 1:4 (1 cement:4 fine sand) for stop cock, with C.I. surface box 100x100x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement:2 coarse sand:4 graded stone aggregate 20mmnominal size) necessary excavation foundation concrete 1:5:10 (1 cement :5 fine sand:10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1cement:3 coarse sand) 12mm thick finished with afloating coat of neat cement complete as per standard design: With Second class bricks |
| 101 | Painting G.I. pipes and fittings with synthetic enamel white paint over a ready mixed priming coat, both of approved quality for new work: 25 mm diameter pipe. |
| 102 | Painting G.I. pipes and fittings with synthetic enamel white paint over a ready mixed priming coat, both of approved quality for new work: 40 mm diameter pipe. |
| 103 | Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality : 40 mm diameter pipe |
| 104 | Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws including excavation, refilling the earth or cutting of wall and making good the same complete wherever required: 40 mm nominal bore. |
| 105 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI:12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 106 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements weighing not less than 106 gms |
| 107 | Providing, laying and jointing glazed stoneware pipes grade ‘A’ with stiff mixture of cement mortar in the of 1:1 (1 cement: 1 fine sand) including testing of joints etc. complete: 150 mm diameter |
| 108 | Providing and laying cement concrete 1:5:10 (1 cement:5 fine sand:10 graded stone aggregate 40mm nominal size) alround S.W. pipes including bed concrete as per standard design: 150 mm diameter S.W. pipe |
| 109 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with 1st class bricks in cement mortar 1:4 (1 cement:4 fine sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C. top slab with 1:2:4 mix (1 cement:2 fine sand:4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement:5 fine sand:10 graded stone aggregate 40 mm nominal size), inside plastering 12mm thick with cement mortar 1:3 (1cement:3 fine sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets: |
| 110 | Making soak pit 2.5 m diameter 3.0 metre deep with 45x45cm dry brick honey comb shaft with well burnt 2nd class bricks and S.W. drain pipe 100 mm diameter, 1.8m long complete as per standard design. |
| 111 | Hiring charge for vehicle Maruti Van (Haltage) of work will be recorded and signed by both the Engineer-in-charge and the agency. |
| 112 | Transportation charge for work supervision by Maruti Van, Asand when required by the engineer - in - charge, the agency will arrange vehicle as mentioned above at his own cost and risk |
| 113 | Wooden armless chair with wooden seat and back of std. size made of Teak / Karai / Chamal wood with complete polishing and varnishing.(Vide TSIC-2016/ for wooden furniture page no.3, SL No. 1) |
| 114 | Wooden chair with arm with wooden seat and back of std. size made of Teak / Karai / Chamal wood with complete polishing and varnishing.(Vide TSIC-2016/ for wooden furniture page no.3, SL No. 2) |
| 115 | Wooden ordinary table of 91.5x61x76.2cm/3\"x2\"x2.5\" with wooden top and one drawer made of Teak / Karai / Chamal wood with complete polishing and varnishing. (Vide TSIC-2016/ for wooden furniture page no.3, SL No. 5) |
| 116 | Wooden half \"Secretariet of 91.5x61x76.2cm/3\"x2\"x2.5\" with wooden top and one drawer & cup board in the right hand side along one tea- tray made of Teak / Karai / Chamal wood with complete polishing and varnishing. b) Boil Board(Vide TSIC-2016/ for wooden furniture page no.3, SL No. 8(b)) |
| 117 | Conference table (Committee meeting hall) oval shape structure made Karai/ Teak wood top fitted by 19mm block board covered by sun mica and middle self 12mm block board both side covered by 4mm commercial ply wood sedf6\" gap top & middle self & both side fitted by sun mica Teak / Karai / Chamal wood with complete polishing and varnishing. c) Boil boar (per RFT)(Vide TSIC-2016/ for wooden furniture page no.7, SL No. 22) |
| 118 | Fire rack of 152.5x121x40.7cm and (4\"x4\"x16\"\") with four shelves without single plank made of Teak / Karai / Chamal wood with complete polishing and varnishing. (Vide TSIC-2016/ for wooden furniture page no.9, SL No. 41) |
| 119 | Book shelf of 121.9x91.5x45.7 cm (4\"x3\"x1½\") with three shelves with having glass door with locking arrangement made of Teak/ Karai wood with complete polishing and varnishing. (Vide TSIC-2016/ for wooden furniture page no.12,SL NO.67.) |
| 120 | Notice board of 91.5x10.2 cm (3\"x2\"x4\") with barfinet in the front of the board with locking arrangement made of Teak/ Karai wood with complete polishing and varnishing. (Vide TSIC-2016/ for wooden furniture page no.13,SL NO.80.) |
| 121 | Steel Almirah (with four shelves) 22 Gauge: 78\"x36\"x18\" (Vide TSIC/2016 for steel furniture Item No. 1, SL No. 1) |
| 122 | Steel chair with arm with writing facility (wooden) in the right hand side std. size with Fiber seat & back. (Vide TSIC/2016 for steel furniture Item No. 6, SL No. 59) |
| 123 | Revolving chair cushioned seat and back. Standard size (Vide TSIC/2016 for steel furniture Item No. 13, SL No. 21) |
| 124 | Providing and fixing G.I. pipes medim class as per IS : 1239 with latest amendment complete with G.I. fittingsincluding trenching and refilling, cutting and making good the walls etc. complete as per CPWD specification and direction of the Engineer - in - charge. A.External work. v. 40 mmdia. nominalbore |
| 125 | Providing and fixing G.I. Bend /elbow in the pipe line including testing of joints complete as per CPWD specification and direction of the Engineer - in - charge.:15 mm dia |
| 126 | Providing and fixing G.I. Reducer with the pipe line including testing of joints complete as per CPWD specification and direction of the Engineer - in - charge.40 x 20 mm dia |
| 127 | Providing and fixing G.I. union as per CPWD specification and direction of the Engineer - in - charge.: 15 mm dia |
| 128 | Washing and development of tube well by using air compressor(Deisel operated), and testing of the well as per specification ( IS : 11189 ) and direction of the Engineer - in - charge. with contractors air compressor:using air compressor of 300 - 450 cfm output for DTW |
| 129 | Providing and fixing of UPVC end cap / well cap suitable for UPVC \"CM\" casing or \"CS\" casing or \"RS\" pipes as per specification and direction of the Engineer - in - charge.100 mm dia |
| 130 | Providing and fixing of UPVC reducersuitable for UPVC \"CM\" casing or \"CS\" casing or \"RS\" pipes as per specification and direction of the Engineer - in - charge. : 150 x 100 mm dia |
| 131 | Providing and shrouding of the deep tube well assembly with washed pea gravels ( 2.0 - 4.75 mm effective size ) as per specification ( IS : 4097) using deep drilling rig and direction of the Engineer - in - charge.with contractor\"s high power rig with pea gravels obtained from Durgapur, West Bengal. |
| 132 | Drilling and boring pilot hole in any soil strata by manual means, collection of soil samples of different strata met with during drilling at various suitable levels, preservation of samples in polythene bags / sample boxes and disposal of excess soil or mud, including the cost for water etc. as required to maintain the pilot hole properly as per specification and direction of the Engineer - in - charge. 100 mm dia |
| 133 | Reaming of pilot hole to an enlarged bore hole in any soil strata by manual means, disposal of excess soil or mud, including the cost for water etc. as required to maintain the bore hole properly as per specification and direction of the Engineer - in - charge. from 100 mm dia pilot hole to 250 mm bore hole |
| 134 | Providing & lowering of UPVC pipe as per IS:12818 after washing of the bore hole by manual means as per specification and direction of the Engineer - in - charge.\"RS\" pipe 100 mm dia |
| 135 | supplying and installation of water lubricated submersible pump having ISI marked of capacity 2000GPH at total haed up to 60 metre. Couple with submersible motor 2HP suitable for 240 voltas (+10% variation single phase 50 Hp. AC supply DOL starting method to run a 1450 RPM along with 35metre. 205 sqm.PVC insulated 3(three) core flate copper cables including fitting fixing and lowering if with 40mm dia G.I pipe upto 100 ft.(30.00mtr) etc. complete as per direction of the Engg-in- charge(40mm dia G.I pipe and fitting will be paid separately ).1 job |
| 136 | suppling and fitting, mixing of single phase motor starter panel unit 2HP capacity compressing with 2 pole conducter, overlead relay, capacitor, volts meter of apropriot brand make with necessary copper wire etc. complete as per direction of engg-in-charge.1X1=1 no. |
| 137 | Supplying and fitting, fixing of 32 amps single phase main switch of BCH/L&T/havel\"s make with necessary copper wire wiring etc. complete as per direction of Engg-in-charge.1 Job |
| 138 | Supplying and fitting, fixing of 110 mm dia Well plug of approved Quality.1X1 = 1 No. |
| 139 | Supplying and fitting, fiximg of MS Box of having size 60 cm X 45cm with slope roof and front shutter with locking arrengements fitted with 4 nos. 40mmX40mmX6mm MS angle of 1.60 m long including providing & fitting wooden board inside the box having size 55cmX55cm thick for fittingall the electrical features like starter, main Switch and including cost of neccesary painting & embedding the box with CC block size 30cmX30cmX60cm with 1:2:4(1 cement:2R/sand/4 Jhama brick aggregate 20 mm gauge) as per direction of the Engg-in-charge (starter, main switch will be paid separately)1 Job |
AI Tender Summary
Tender Timeline
Apr 13, 2023
11:30 IST
Tender Published
Tender notice published.
CompletedApr 26, 2023
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedApr 26, 2023
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender