Tender For Construction Of Common Kitchen Building At Municipal Primary School At Weakly Market Near Ward No.18 In Nellikuppam Municipality
Tender Value
28 Lakhs
Estimated cost
Bid Submission
11 Apr 2023
0 days left
EMD
28000
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
nellikuppam → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Common Kitchen Building At Municipal Primary School At Weakly Market Near Ward No.18 In Nellikuppam Municipality Morning Meal Centre
BOQ
| Sl. No. | Item Description |
| 1 | Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. footing |
| 2 | footing |
| 3 | Sand filling in foundation with clean river sand in layer of 15cm thick well watered rammed to consolidation including cost and conveyance of sand to site incluidng labour charges etc., complete as per standard specification |
| 4 | Cement concrete of mix in 1:4:8 (one cement – four sand – eight broken stone) using ISS Hard broken granite stone jelly of 40 mm gauge from approved quarry to working site including cost of conveyance of all materials to working site and all labour charge for mixing, placing, compaction, finishing and curing by the direction of departmental engineers instruction etc, complete and as per standard specification |
| 5 | Supplying and Erecting of centering for sides and soffits including necessary supports and shuttering to the required height for RCC works with standard Specifications etc. Complete Column |
| 6 | Gradebeam |
| 7 | roof slab |
| 8 | Providing and laying in position Standardised Concrete Mix M-20 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 325Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of Crushed Stone Sand (M- Sand), but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - |
| 9 | Supplying and fabricating and placing in position steel reinforcement using Mild Steel or ribbed for steel rods for all RCC works as per the design given including cost of Steel and binding wire etc, complete in all floors complying with standard specification using MS plain rods or RTS rods. |
| 10 | Brick work in cement mortar 1:5 (one part of cement andfive part of sand) using best quality country bricks from approved quarry to working site including cost and conveyance of all materials to working site and alllabour chargesforsimeltaneous pointing with same mortar by the direction of departmental engineers instruction etc, complete and as per standard specification. for below basment |
| 11 | for superstructure |
| 12 | Supplying and filling of well gravel by lorry in basement filling including conveyance loading and unloading charges and all other incidential charges filling laying watering and consolidation etc., complete as directed by the Dept., Officers with standard specification. |
| 13 | Plastering with cement mortar (1:5) 12mm thick in all floors including cost and conveyance of all materials to site and labour charges etc, complete complying with standard specifications (S.I.309) |
| 14 | Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification |
| 15 | Painting 2 coats with approved cement paint over cement plastered wall surface, ceiling and other new surface and including cleaning, preparing the surface and curing etc., complete. |
| 16 | Paving the floor with design Rajasthankotta tiles (colour and shade as directed) of size 610 mm x 610mm x 20mm in all floors over a base layer of cement mortar 1:3 (one cement and three sand ) 20mm thick laid in-situ and pointed with same coloured cement etc, complete as per standard specification |
| 17 | Paving the floor with design Antiskirt ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick laid in-situ and pointed with same coloured cement |
| 18 | Dadooring the colour glazed wall tiles of size 300x20x6 mm burden in cm 1:2(One cement and two sand) 10 mm thick and pointing with colour cement using 0.40kgs/m2 the rate including the cost of tiles and colour cement and also including finishingthe top surface etc,complete. |
| 19 | Supply and delivery of pre- Painted Galvanaized SheetCoruugated Iron Sheet of 0.8mm thickness - 10 m2 including All material And labour cost etc, Complete asper standard specification. |
| 20 | Supply and deliveryof following ISMB - I sections,\"L\" angle,MS plate,MS bolt and nuts.including all cost and conveyance of materials and labour charges for erection charges with one coat of red oxide primer etc., complete as per the standard specifications.. |
| 21 | Suppliying and fixing of weldmesh 7.5 x 2.5cm, 10 gauge etc., complete complying with Standard Specificaiton and as directed by the departmental officer. |
| 22 | Supply and Fixing door shutters for Solid Core Flush Shutters with teakply on both side. with teakwook lipping alround 35mm thick Single leaf confirning to IS :12406/1989 with 35 x 12mm T.W lipping on all edes necessaryadhegives and cp screens complingwith standard specification .the rate is inclussive three coats of best quality varnish but excluding cost of fittings suches 300mm tower bold etc.complete. SOR 2022-23 PAGE - 42 |
| 23 | Supply and fixing of PVC Solid Doors using 19gauge 19mm MS Sq,tubes for styles and frames, 15mm MS Sq.tubes for to, Lock and bottom rails. The Steel Tubes shall be covered with 5mm thick Solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in positionincluding furniture and fittings. The over all size of styles shall be 50mm X 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm X 30mm. The over all size of frames shall be 50mm X 45mm with suitable tabate for housing the shutter etc, complete as per standard specification. (PWD SOR ITEM NO.125(A) PG. NO.43) |
| 24 | Supplying and fixing in position of alulminium anodised colour matt finish Louvered Ventilator. The outer frame will be 62x38x2mm @ 1.17 Kg / m and the louvers with moving arrangements will be made with Alu. Channel of size 60x30x4 mm @ 1.27 kg /m with necessary glass pans for louvers4mm thick Al. Clips, including all materials, labour & power consumption charges required for fabrication if necessary chipping dismantling making holes in RCC columns,beamsor masonry wherever necessary withpower drill to the extent requiredand make good to the original conditions after fixing etc., complete. The Aluminium sirface is to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868/1962 of anodic film thickness of not less than15 microns (fifteen) for all sections. |
| 25 | Supply and Fixing of Solid UPVC Windows Shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS tubes shall be covered with 5mm thick solid PVC Sheets. Shutter using 5mm thick solid PVC Sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top suitable rabate for housing the shutter |
| 26 | Suppliying and fixing in position Indian water closet of size 580 x 440 mm, white glazed earthern ware of approved quality with \"p\" trap or \"S\" trap confiming to IS: 2556 Part XII with sand cushion and 40mm broken brick jelly in Cementlime concrete 1:2:5 (One part of Cement Two part of Sand and five parts of brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to cast iron soil pipes/PVC pipe by dismantling brick masonary, RCC Roof/ Floor slab and making good. the distabed portion to origional condition without leakage etc., complete complying with Standard Specificaiton and as directed by the departmental officer. |
| 27 | Wiring with 2X 1.5 Sq. mm PVC unsheathed Cu.cpnductor of 1100 V grade in suitable PVC rigid pipe in wall and ceiling with Pvc accessories with 150mmx100mmx113mm, T.W switch boxin flush with wall with 3mm thick hylem sheet cover for 5A 3 pin non inter locking CS plug with painting of suitable colour with continous earth wire connection of 14 SWG TC wire for open PVC Light/Fan point.SD 25 |
| 28 | Wiring with 2X 1.5 Sq. mm PVC unsheathed Cu.cpnductor of 1100 V grade in suitable PVC rigid pipe in wall and ceiling with Pvc accessories with 150mmx100mmx113mm, T.W switch boxin flush with wall with 3mm thick hylem sheet cover for 5A 3 pin non inter locking CS plug with painting of suitable colour with continous earth wire connection of 14 SWG TC wire for open PVC plug point. (SD.No.38) |
| 29 | Supply and fixing of single box type 4\"36 W flu fitting complete with copper choke and condensor with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting SD 87 |
| 30 | Supplying and fixing of 1200mm ( 48\"\" ) sweep AC ceiling fan complete with regulator with 1M down rod including S & F of fan clamp with side plates and cross arm SD 107 |
| 31 | Supply and Delivery and fixing of 1000 Litres HDPE tank as per IS12701/1996 including loading,unloading,transportion and labour charges for fixing of the GI pipes and specialsfor pipe connection works including cutting,threading and fixing charges etc,complete. |
| 32 | Supply of PVC pipe and G.I pipes and PVC pipe & Specials. 32mm GI Pipe |
| 33 | 32mm GI Tee |
| 34 | 32mm GI Bend |
| 35 | 32mm GI Coupling |
| 36 | 32mm GM gate Valve |
| 37 | 25mm PVC Pipe |
| 38 | 25mm PVC Coupling |
| 39 | 25mm PVC Tee |
| 40 | 25mm PVC Elbow |
| 41 | 20mm Tap |
| 42 | Providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 (One Cement, Two sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panellingwherever necessary and as directed by the departmental officers) |
| 43 | Supplying and fixing of rolling shutters shall be pull and push type (Mannually operated) made of 18G/3\" lathe sections which consist of five main parts such as curtain, lock plate, guide channels rollers and hood cover. These five main parts are made out of special components detailed below: curtain shall be of 18G/3\" lath sections cut to required size and filled with heavy cast iron / MS clips. For 8\"0\"(2.45m) high rolling shutter lath sections provided shall be not less than 37 numbers. Lock plate shall be 10G MS sheet and attached to the side brackets with 20mm square bar.Side brackets shall be of 10G MS plate and cast iron \"U\" clamps shall be rivetted to the side brackets. Roller shall be of heavy cast iron pullies fitted with heavy duty \"C\" class 40mm steel pipe and high tensile high carbon coil springs. 2 springs shall be supplied. Side brackets shall be of 10G MS plate and cast iron \"U\" clamps shall be rivetted to the side brackets. Hood cover shall be of 0.8mm CRCA sheet reinforced with 25mmx25mmx3mm MS angle or gate channel. The rolling shutter in addition to the above should have pulling hook and shall be coated on exposed area with heavy coat of red oxide primer etc., complete. |
AI Tender Summary
Tender Timeline
Apr 05, 2023
11:30 IST
Tender Published
Tender notice published.
CompletedApr 11, 2023
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedApr 11, 2023
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender