Tender For Rasipuram Municipality - Construction Of Common Kitchen At Bharathithasan Salai Municipal Middle School In Rasipuram Municipalty.
Tender Value
20 Lakhs
Estimated cost
Bid Submission
06 Apr 2023
0 days left
EMD
20000
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
rasipuram → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Rasipuram Municipality - Construction Of Common Kitchen At Bharathithasan Salai Municipal Middle School In Rasipuram Municipalty. Construction Of Common Kitchen At Bharathithasan Salai Municipal Middle School In Rasipuram Municipalty.
BOQ
| Sl. No. | Item Description |
| 1 | Earth work excavation for foundation and depositing on bank with in the initial lead of 10m and a lift of 2m in hard stiff clay, stiff block cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size boulders etc. complete as per standard specifications. |
| 2 | Cement concrete 1:4:8using 20 mm machine chips including cost of centering (for sides and supports), Expansion joint using bitumen pad and other materials and labour charges etc., complete as per std. specification. |
| 3 | Supplying and erecting centering for sides and soffits including supports and strutting with all cross bracings using M.S Sheets of size 90cmx60cm and B.G 10 Stiffended with welded M.S.Angles of size25mmx25x3mm for boarding laid over silver oak(or)country wood joist of size 10cmx6.5cm spaced at about 90cm centre to centre and supported by casurina props 10cm to 13 cm dia spaced out 75 cm centre to centre or at suitable intervals etc.,complete complying with std.specification |
| 4 | Footing |
| 5 | column |
| 6 | Slab and Beam |
| 7 | Reinforced Cement Concrete 1:1.5:3 (one cement, one and half fine aggregates and three coarse aggregates) using 20mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges etc., complete as per standard specification |
| 8 | From GL to 1.5m BELOW GL |
| 9 | Above basement |
| 10 | Supply and fabrication and placing in position of TMT steel roads to required size and length as directed by the departmental officers including cost of binding wire, cutting, bending and tying with proper position etc., including cost and conveyance of all materials to site and all labour chargesetc., complete as per Standard Specification. |
| 11 | Brick work in following Cement Mortar using Fly Ash Bricks of 230 x 110 x 70mm size conforming to IS: 12894-1989 Class designation not less 50 kg./ sq.cm. average compressive strength in cement mortar 1:5 for load bearing structures for foundation and basement and for superstructure including curing, etc., complete complying with standard specifiction. |
| 12 | Below Basement |
| 13 | Above basement |
| 14 | Supplying and filling in foundation andbasement with Well Gravel in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification. |
| 15 | Plastering with cement mortar (1:4) 20mm thick in all floors including cost and conveyance of all materials to site and labour charges etc, complete complying with standard specifications (S.I.309) |
| 16 | Plastering with cement mortar (1:5) 12mm, thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications (S.I.306) |
| 17 | Plastering with cement mortar 1:3,10 mm ,thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications (S.I.306) |
| 18 | Paving the floor with Vitrified tiles of approved quality and colour of size 600x600x8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3(one cement three sand) 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer.The colour & quality of tiles should be got approved by Municipal Engineer before use on work |
| 19 | Paving the floor with design Antiskirt ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (one cement and three sand ) 20mm thick laid in-situ and pointed with same coloured cement |
| 20 | Dadooing walls withGlazed tiles of sizes 305mm X200mm X 6mm size of approved make and quality and colour l Set in cement mortar 1:2 (one cement ,two sand) over 10 mm base layer plastering and pointing with white cement neatly as directed. |
| 21 | Manufacturing, Supplying and fixing inposition of Mild Steel Door using outer frames of size 40x40 x6mm and shutters with 18G CRC sheet in center portion and finishing with necessary locking arrangements, painting with primary coat as directed by size 1.20x2.10M = 2.52M2 departmental officer etc. complete. |
| 22 | Manufacturing, supplying and fixing in position of MILD STEELWINDOWS with openable shutters, outer frames and shutter frames shall be made out of steel sections conforming toI.S. 7452/1990. The outer frames and shutter frames of windows made out of \" Z \" section ( F.7D ) of size 25 X 20 X 3mm and confriming to I.S.7452/1990. Mullions are made out of ( F.4B ) \" J \" sections of size 46 X 25 X 3mm and confriming to I.S. 7452/1990. The shutter shall be individual and each of them can be operated seperately. Sash bars shall be made of \" T \" ( T 2 ) of size 25 X 25 X 3mm. Four numbers of 40 X 40 X 3mm angel hold fasts of 230mm length should be welded to the outer frame of sturdy hinges and one number of handel-cum-latch of special type shall be left for its easy operation. One number of adjustable wind stay with locking bracket of sufficient length shall be provided for each shutter. Mild steel square guard bars of 12mm size shall be welded to the inner face of the window at equal intervals not exceeding 100mm spacing and 18G CRC sheet for shutter panes and welded with shutter frame. |
| 23 | Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification |
| 24 | Fabricating supplying and fixing of pre painted galvanized iron sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers. |
| 25 | Painting two coats with ready mixed Plastic Emulsion Paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification. - 10 sq.m |
| 26 | Painting two coats with Ready Mixed Enamel Paint over the new iron works of approved quality and colour without priming coatincluding the cost all materials etc.,complete, in all floors. |
| 27 | Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with TW switch box and 5A FT switch with painting of suitable colour for open PVC light point / fan point (for electronic regulator) (4 points per coil) SD 17 |
| 28 | Supply and fixing of 1200mm (48\") AC ceiling fan complete with stepped electronic 300W regulator with 1 meter down rod on the existing clamp SD 107 |
| 29 | Supply and fixing of 450mm (18\") sweep AC exhaust fan complete with necessary wall opening and making good of the wall.etc, complete as per standard specifications. SD 115 |
| 30 | Supply and fixing of 3 Nos. 5A (3 pin and 2 pin) combined flush type wall socket with control switches concealed in suitable TW box covered with hylem sheet in flush with wall with earth connection (for computer plug socket) SD.139 |
| 31 | Wiring with 2x4 sqmm (56/0.3) PVC insulated SC unsheathed Cu.Conductor cable of 1100V grade in suitable pipe on wall and ceiling with PVC accessories with 150mm x 100mm x 63mm TW switch box for 15 A 3 pin non inter locking CS plug with painting of suitable colour, with continuous earth wire connection of 14 SWG TC wire for open PVC power plug point SD 13 |
| 32 | Supply and fixing of 20 W LED tube light fitting with ISI Mark with all accessoreis including cost of an LED light with accessories and fitting charges etc., complete. |
| 33 | Supply and fixing of TNEB meter board suitable for 3 phase 63A service connection made up of suitable angle iron frame work of size 2 feet - 1/2 feet using angle iron of size 1/2\" x 1 1/2\" x 1/4\" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1/2 feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos. 63 Amps fuse units (500V), 1 No. neutral link, copper earth flat of size 1\" x 1/4\" with inter connection of EB meter to fuse units by 7/16 PVC insulated copper wire earth connection complete SD 128 |
| 34 | Supply and run of 2 of 4 sqmm (56/0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with continuous earth wire connection of 14 SWG TC wire with painting of suitable colour SD 65 |
| 35 | Supply and run of 2 of 4 sqmm (56/0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable heavy gauge GI pipe on wall and ceiling with continuous earth wire connection of 14 SWG TC wire with painting of suitable colour SD 70 |
| 36 | Supply and run of 2 of 1.5 sqmm (22/0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection 14 SWG TC wire with painting of suitable colour SD 64 |
| 37 | Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) 1 No. 32A DP MCB as incoming and 6 Nos. 6A to 32A SPMCB outgoing in flush with wall and making good of the concealed portion with earth connection only. The MCB DB and MCB\"s should be with ISI mark SD 167 |
| 38 | Earthing as per the ISI specification with an earth electrode of 2.10metre class \"B\" GI pipe of dia not less than 40mm with copper eartth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry including all cost & conveyance SD 234 |
| 39 | Supply and fixing of following PVC pipes and specials complying with standard specification. |
| 40 | 40mm PVC pipe |
| 41 | 40mm PVC Elbow |
| 42 | 40mm PVC Bend |
| 43 | 40mm PVC Tee |
| 44 | 40mm PVC gate valve |
| 45 | 40 x 20mm PVC Reducer |
| 46 | 20mm PVC pipe |
| 47 | 20mm PVC Bend |
| 48 | 20mm PVC Tee |
| 49 | 20mm PVC Elbow |
| 50 | 20mm PVC Coupling |
| 51 | Supply and fixing in position of MS grill with Doors and Windows with one coat of Red oxide with primer including all costs such as welding, grinding and fabrication work charges, cost, conveyance of all materials to site etc., |
AI Tender Summary
Tender Timeline
Mar 28, 2023
11:30 IST
Tender Published
Tender notice published.
CompletedApr 06, 2023
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedApr 06, 2023
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender