University Of Kashmir (Jammu) has published Tender For Civil And Sanitary Stage Works For The Year 2023-24 In All Campuses At University Of Kashmir. Submission Date for this Tender is 04-04-2023. Kitchen Equipment Tenders in Srinagar Jammu And Kashmir. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | Supply of labors. |
| 2 | Mazdoor. |
| 3 | Carpenter 1st class. |
| 4 | Carpenter 2nd class |
| 5 | Mason 1st class. |
| 6 | Mason 2nd class. |
| 7 | Plumber. |
| 8 | Black Smith. |
| 9 | Earth work in excavation by manual/Mechanicalmeans in foundation trenches or drains (not exceeding 1.5M in width as well as 10Sqm on plan) including dressing of sides ramming of bottoms lift up to 1.5M including getting out the excavated soil and disposal of surplus excavated soil within a lead as directed from edge of cutting .All kinds of soil. |
| 10 | Concrete work.Providing and laying in position cement concrete of specified grade including the cost of centering and shuttering. All work up to all levels.1:4:8 (1Cement: 4 coarse sand: 8 grade stone aggregate 40mm nominal size) Crushed |
| 11 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering. All work up to all levels. 1:3:6 (1Cement: 3 fine sand: 6 graded stone aggregate 20mm nominal Size) Crushed |
| 12 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering. All work up to all levels. 1:2:4 (1Cement: 2 coarse sand:4 graded stone aggregate 20mm nominal Size) Crushed |
| 13 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement all work up to all levels. 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) Crushed |
| 14 | Providing and laying damp proof course with cement concrete 1: 2: 4 (1 cement: 2coarse sand: 4 graded stone aggregate) including waterproofing compound |
| 15 | 40mm stone aggregate 12.5mm nominal size. |
| 16 | 50mm stone aggregate 20mm nominal size |
| 17 | Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses plinth and string courses fillets, columns, pillars, beams, piers, abutments, suspended floors, posts and struts, etc. up to all floor level excluding cost of centering, shuttering, finishing and reinforcement. 1:1.5:3 (1 cement:1.5 coarse sand:3 graded stone agg. 20 mmnominal size) Crushed |
| 18 | Steel Work Reinforcement for RCC works including straightening, cutting, bending placing in position and binding all complete up to all floors. Thermo mechanically heated bars. |
| 19 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 20 | Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Welded |
| 21 | Providing and fixing of M. S. Grill (ornamental) of angles / tees / flats / round and square bars/Hollow sections duly welded in frames of windows or with approved design, welded complete including applying a priming coat of red oxide complete |
| 22 | Form work. Centering and shuttering including strutting propping etc. removal of form work in |
| 23 | Foundation footings basis of columns etc. for mass concrete. |
| 24 | Suspended floors, roofs, landings, balconies, access plat forms, Lintels, beams, plinth beams, girders, bressumers, cantilevers, Columns, pillars, piers, abutments, posts and struts and edges of slabs etc. (M.S. Plates/Ply wood) |
| 25 | Stairs, (excluding Landings) except spiral cases.(kit ply wherever required) |
| 26 | Brick work. Brick work with FPS bricks of class designation 75 upt to plinth level. In cement mortar 1cement: 6 fine sand mortar |
| 27 | Brick work with FPS bricks of class designation 75in super structure up to all floors. In cement mortar 1cement: 6 fine sand mortar. |
| 28 | Half brick masonry with bricks of class designation 75 in superstructure up to all floor levels. |
| 29 | In cement mortar 1cement: 3 fine sand mortar. |
| 30 | In cement mortar 1cement: 4 fine sand mortar |
| 31 | Wood Work. Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position. 1st Class imported wood. |
| 32 | Providing and fixing 30-35 mm thick glazed shutters for windows and clearstory windows using 8.70kg/Sqm. (3.5mm thick) glass panes including black enameled ISI marked M.S. butt hinges with necessary screws. First. Class imported wood. |
| 33 | Providing and fixing 30-35 mm thick wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4mm with wire of dia. 0.63 mm for doors, windows and clerestory windows including ISI marked bright finished or / and black enameled M.S. butt hinges with necessary screws.First. Class imported wood. |
| 34 | Providing 40x5mm flat Iron hold fast 40 cm long including fixing of frame with 10mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15 cm 1:3:6 mix (1cement: 3 coarse sand: 6 graded stone aggregate 20mm nominal size) |
| 35 | Providing and fixing 30-35 mm thick paneled door shutters, including ISI marked black enameled M.S. butt hinges with necessary screws including paneling of 12mm thick laminated board both sides laminated as per the approved design complete with required beading/moldings. (styles and rails shall be of standard size) in fittings First. Class imported wood. |
| 36 | Providing and fixing 30-35 mm thick paneled door shutters, including ISI marked black enameled M.S. butt hinges with necessary screws including cost of 25-35mm thick paneling of approved design with required beading/moldings.First. Class imported wood. |
| 37 | Providing and fixing 30-35 mm thick paneled/ flush door shutters, including ISI marked black enameled M.S. butt hinges with necessary screws Readymade ornamental modular, factory manufactured machine made of hard wood teak finished, of approved quality, color and shade. |
| 38 | Providing and fixing 32 mm thick paneled door shutters with wood carved panels (Carving on both sides) including polishing, and ISI marked black enameled M.S. butt hinges with necessary screws as per the approved designcomplete with required beading/moldings. (styles and rails shall be of standard size)First. Class imported wood. |
| 39 | Providing and fixing wood work in frame work / joists of false ceiling, partitions, joists etc. sawn and put up in position.First. Class imported wood. |
| 40 | Providing hoisting and fixing trusses / purlins / rafters / posts, post plates, in planks and any sort of work or like components, including cost of screws nails etc. complete.First. Class Budloo wood. |
| 41 | Providing hoisting and fixing trusses / purlins / rafters / posts, post plates, in planks and any sort of work or like components, including cost of screws nails etc. complete.First. Class imported wood. |
| 42 | Providing hoisting and fixing trusses / purlins / rafters / posts, post plates, in planks and any sort of work or like components, including cost of screws nails etc. complete.First class Popular wood. |
| 43 | Providing and fixing of wooden paneling/ lining of 12mm (net thickness) including providing and fixing of ground frame work (50x25mm or as specified) of first class Budloo wood/ 19mm ply including cost of screws, wooden plugs etc. complete as per directions of EIC |
| 44 | made from export wood |
| 45 | made from Budloo wood |
| 46 | Providing and fixing of ply wood including cost of nails adhesive etc. complete at all places. |
| 47 | 4-6 mm thick |
| 48 | 12 mm thick |
| 49 | 19 mm thick |
| 50 | Providing and fixing water proof BWR ply wood ISI marked including cost of nails adhesive etc. complete at all places. |
| 51 | 6 mm thick |
| 52 | 12 mm thick |
| 53 | 19 mm thick |
| 54 | Providing and fixing of single side laminated ply wood including cost of nails adhesive etc. complete at all places. |
| 55 | 6 mm thick |
| 56 | 12 mm thick |
| 57 | 18 mm thick |
| 58 | Providing and fixing of 19mm thick commercial block board at all places including cost of nails and adhesive complete. Thickness/ Pattern/ Design to be approved by EIC |
| 59 | Providing and fixing of Dulmica/ sun mica sheeting including cost of nails and adhesive complete. |
| 60 | Providing and fixing wood work in fencing that is in planks of the following nominal size excluding cost of posts and runners. 1st class Budloo wood. (ornamental) |
| 61 | 20 mm thick. |
| 62 | 25 mm thick. |
| 63 | 35 mm thick. |
| 64 | Providing and fixing of ornamental cornice of following size. 1st class budloo/imported wood. |
| 65 | 40-50 mm face |
| 66 | 65 mm face |
| 67 | 75 mm face |
| 68 | Providing and fixing of PVC edge beading |
| 69 | 12 mm face |
| 70 | 19 mm face |
| 71 | 25 mm face |
| 72 | Providing and fixing 20mm thick overlapped weather boarding in soffits of 1st class imported wood including applying priming coat of approved quality primer. |
| 73 | Providing and fixing of planed eaves boarding 250mm x 32mm size of 1st Class imported wood. |
| 74 | Providing and fixing of planed eaves boarding 250mm x 32mm size of 1st Class Budloo wood. |
| 75 | Providing and fixing of wooden beading ornamental 25mmx6mm size of Budloo wood. |
| 76 | Providing and fixing of wire gauze using galvanized M.S wire gauze of average width for aperture 1.4mm with wire of dia. 0.63mm for doors windows and clearstory windows including cost of beading complete. |
| 77 | Providing and fixing of chicken mesh wherever required of specified size including cost of beading and nails complete. |
| 78 | Providing and fixing of glass pans with wooden fillets of required size wherever necessary. |
| 79 | Glass pans 3.5mm thick weighing 8.70 Kg / sqm. |
| 80 | Glass pans 5mm thick weighing 13.75 Kg / sqm. |
| 81 | Providing and fixing of reflective glass panes 3.5 mm thick in doors windows and clearstory windows including cost of budloo wood beading of required size. |
| 82 | RoofingProviding & fixing corrugated G.S. sheet roofing fixed with nails with bitumen and G.I limpet washers /self drilling screws with washers/J- Hooks (up to a pitch of 60 degree) excluding the cost of purlins rafters and trusses |
| 83 | 0.63 mm thick with zinc coating not less than 275 gm./Sqm |
| 84 | 0.50 mm thick with zinc coating not less than 275 gm./Sqm |
| 85 | Providing and fixing pre-coated galvanized iron profile sheets/corrugated/tiled (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length up to 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self-drilling /self-tapping screws of size (5.5x55 mm) with EPDM seal, complete up to any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 86 | Providing ridges/ valleys or hips of width 60cm over all width plain G.I sheet fixed with nails G.I limpet washers complete 0.63 mm thick with Zinc coating not less than 275 gm./Sqm |
| 87 | Providing ridges/ valleys or hips of width 60cm over all width plain G.I sheet fixed with nails G.I limpet washers complete 0.50 mm thick with Zinc coating not less than 275 gm./Sqm |
| 88 | Providing and fixing pre-coated galvanized steel sheet roofing accessories 0.50 mm (+ 0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self-drilling/ self-tapping screws complete. Ridges/Valleys plain (450 - 600 mm). |
| 89 | Providing and fixing Tiled/GRIDfalse ceiling of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams/ sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paintpaint, all complete for all heights as per specifications,drawings and as directed by Engineer-in-charge. |
| 90 | GI Metal Ceiling Lay in plain Tegular edge Global white/Off white colour tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending |
| 91 | GI Metal Ceiling Lay in perforated Tegular edge global white colour tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes (as per directions of EIC) and having NRC (Noise Reduction Coefficient) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece. |
| 92 | 8-12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard manufactured from natural gypsum as per IS 2095 part-I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit. |
| 93 | 8-12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fiber conforming to IS: 2095 part-I, of size 595x595 mm, having perforation of9.7x9.7 mm at 19.4 mm c/c with center borders of 48mm and the side borders of 30 mm, (or as per directions of EIC) backed with non woven tissue on the back side, having an NRC (Noise Reduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing. |
| 94 | 8 mm thick fully perforated Calcium Silicate Board made with Calcareous and Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process to give stable crystalline structure with minimum compressive strength 225 kg/cm2, bending strength 100 kg/cm2, of size 595x595 mm, having perforation of dia. 10mm with minimum perforated area 18% with non-woven tissue on the back side, having an NRC (Noise Reduction Certificate) of 0.85, with 50 mm thick rock wool of 48 kg/cum backing. |
| 95 | Providing and fixing of acoustic insulation with 24 gauge G.I net wire netting mesh or frame with G.I stipules etc. |
| 96 | 50mm thick filled in polythene bags. |
| 97 | 100mm thick filled in polythene bags. |
| 98 | 150mm thick filled in polythene bags. |
| 99 | Providing and fixing of jute fabric as per approved sample with bituminous paint complete. |
| 100 | Providing and fixing of 10-12mm thick P.O.P. perforated/ non perforated tiles of 2"x 2"size of approved quality including jointing complete. |
| 101 | Flooring/tile work.Cement concrete flooring 1:2:4 (1Cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry but excluding cost of nosing of steps etc. complete. |
| 102 | 40 mm thick 20mm nominal size stone aggregate (crushed) |
| 103 | 50 mm thick 20mm nominal size stone aggregate (crushed) |
| 104 | Providing and fixing 1st quality ceramic glazed Digital tiles conforming to IS: 13753 of minimum thickness 5mm of approved makein all colors, shades, except burgundy, bottle green, black of any size as approved by Engineer In Charge in skirting, riser of steps and dados over 12mm thick bed of cement mortar 1:3 (1 Cement: 3 coarse sand) and jointing with grey cement slurry @3.3 Kg per Sqm including pointing in white cement mixed with pigment of matching shade complete. (Sample to be approved by competent authority) |
| 105 | Extra for using chemical (Tilofix) of required thickness instead of cement mortar/ slurry |
| 106 | Providing and fixing 1st quality ceramicfloortiles 300x300mm (thickness to be specified by the manufacturer) of 1st quality conforming of IS :13755in all colors, such as white, Ivory, Grey, Fume Red Brown or as approved by Engineer In Charge over 20mm thick bed of cement mortar 1:4 (1 Cement: 4 coarse sand) including pointing the joints with white cement and matching pigment etc. complete (Sample to be approved by competent authority) |
| 107 | Providing and fixing 1st quality ceramicfloortiles 600x600mm (thickness to be specified by the manufacturer) of 1st quality conforming of IS :13755in all colors, such as white, Ivory, Grey, Fume Red Brown or as approved by Engineer In Charge over 20mm thick bed of cement mortar 1:4 (1 Cement: 4 coarse sand) including pointing the joints with white cement and matching pigment etc. complete (Sample to be approved by competent authority) |
| 108 | Providing and fixing of Buj tile cladding of required pattern. Shade and design over 20mm thick cement plaster 1:3 mix (1 cement: 3coarse sand) including jointing with neat cement slurry complete. |
| 109 | Providing and fixing of Interlocking/Chequered precast cement concrete tiles colored(rubber finish) in foot paths & courtyards jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and cleaning etc. complete on 20mm thick layer of dry sand . |
| 110 | 40mm thick. |
| 111 | 50mm thick. |
| 112 | 75mm thick. |
| 113 | Providing and laying mud flooring mixed with chopped dry wheat grass including leveling and finishing to the following thickness complete in all respects. |
| 114 | 75mm thickness. |
| 115 | 50mm thickness. |
| 116 | Providing and laying of polythene of specified thickness under mud flooring complete. |
| 117 | Providing and laying polished vitrified floor tiles of size 600x600mm (thickness to be specified by the manufacturer) approved make in all colors, shades as approved by engineer- in-charge laid on 20mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand) including pointing the joints with matching pigment or any other relevant pigment as directed including cleaning the floor after finishing of work including spacers (Sample to be approved by competent authority) |
| 118 | Providing and laying anti-skid vitrified floor tiles of size 600x600mm (thickness to be specified by the manufacturer) approved make in all colors, shades as approved by engineer- in-charge laid on 20mm thick bed of cement mortar 1:4 (1cement: 4 coarse sand) including pointing the joints with matching pigment or any other relevant pigment as directed including cleaning the floor after finishing of work including spacers (Sample to be approved by competent authority) |
| 119 | Providing and laying polished vitrified floor tiles of size 600x600mm (thickness to be specified by the manufacturer) approved make in all colors, shades as approved by engineer- in-charge laid on chemical (Tilofix) of required thickness including pointing the joints with matching pigment or any other relevant pigment as directed including cleaning the floor after finishing of work including spacers (Sample to be approved by competent authority) |
| 120 | Providing and laying anti-skid vitrified floor tiles of size 600x600mm (thickness to be specified by the manufacturer) approved make in all colors, shades as approved by engineer- in-charge laid on chemical (Tilofix) of required thickness including pointing the joints with matching pigment or any other relevant pigment as directed including cleaning the floor after finishing of work including spacers (Sample to be approved by competent authority) |
| 121 | Providing and fixing 18mm thick mirror polished, machine cut for floors, kitchen platform, vanity counters facieses and other similar locations of required size of approved shades, color and texture laid over 20mm thick base cement mortar 1:4 (1cement: 4 coarse sand) and joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing etc. including moulding complete at all levels. |
| 122 | Ganite of any color as approved by EIC |
| 123 | Providing and fixing of laminated board flooring AC IV using HDF solid core planks of specified thickness approved quality and color with tongued and grooved jointing including cost of thermo cot and other accessories complete. (Sample to be approved by EIC) |
| 124 | Providing and fixing of MDF cornice 25mmx20mm In size. |
| 125 | Providing and fixing of MDF cornice 2.5" In face. |
| 126 | Plaster |
| 127 | 15mm thick cement plaster on brick / concrete wall of mix 1:6 (1cement: 6 coarse sand) |
| 128 | 12mm thick cement plaster on half brick / concrete wall of mix 1:6 (1cement: 6 coarse sand) |
| 129 | 6 mm thick cement plaster onconcrete wall of mix 1:3 (1cement: 3 coarse sand) |
| 130 | POP/Wall putty |
| 131 | Providing and applying plaster of Paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete. |
| 132 | Providing and applying cemement based wall putty 1mm thickness over plastered surface to prepare the surface even and smooth complete. |
| 133 | Providing and applying cemement based wall putty 2mm thickness over plastered surface to prepare the surface even and smooth complete. |
| 134 | Painting. Removing painting by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 135 | Removing white or color wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 136 | Removing lime punning/POP from walls including sand papering and disposal of rubbish as directed etc. complete. |
| 137 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade. New work (two or more coats) over and including priming coat with cement primer. |
| 138 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade. Old work (one or more coats). |
| 139 | Distempering with 1st quality acrylic washable distemper (readymade) of approved manufacturer and of required shade and color complete as per manufacturer"s specification. |
| 140 | One or more coats on old work |
| 141 | Two or more coats on new work |
| 142 | Finishing walls with water proofing cement paint of approved brand and manufacture to give an even shade. |
| 143 | New work (two or more coats applied @ 3.84 kg/10sqm)including cost of priming coat @0.80 liter/Sqm |
| 144 | Oldwork (one or more coats applied @ 2.20 kg/10sqm) |
| 145 | Applying priming coat with ready mixed white primer of approved brand and manufacture on wood work. |
| 146 | Applying priming coat with ready mixed zinc oxide chromate primer of approved brand and manufacture on steel galvanized iron/steel works. |
| 147 | Applying one coat of cement primer of approved brand and manufacture on wall surface. Cement primer. |
| 148 | Painting with synthetic enamel paint of approved brand and manufacture of required color to give an even shade .one or more coats on old wood/plaster work. |
| 149 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade two or more coats on new wood work/plastered surface including sand papering and knotting. |
| 150 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade two or more coats on new steel work including sand papering and knotting complete. |
| 151 | Painting with synthetic enamel paint of approved brand and manufacture of required color to give an even shade .one or more coats on old steel work. |
| 152 | Wall painting with plastic emulsion paint (two or more coats) of approved brand and manufacture to give an even shade. New work |
| 153 | Wall painting with plastic emulsion paint (one or more coats) of approved brand and manufacture to give an even shade. Old work |
| 154 | Finishing withexterior acrylic paint of approved brand and manufacture (two or more coats) at all locations prepared and applied as per manufacturer"s specifications including appropriate priming coat, preparation of surface, etc. complete on all surfaces. Old work |
| 155 | Finishing withexterior acrylic paint of approved brand and manufacture (two or more coats) at all locations prepared and applied as per manufacturer"s specifications including appropriate priming coat, preparation of surface, etc. complete on all surfaces. New work including appropriate priming |
| 156 | Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required color to give an even shade: Old work (two or more coats) |
| 157 | Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required color to give an even shade: New work (two or more coats) including a coat of approved steel primer including a coat of Moderant Solution |
| 158 | Finishing with wall texture of approved brand and manufacture including preparation of ground work complete. |
| 159 | Dismantling/Demolishing.Dismantling of existing chain link fencing, steel work complete, including stacking of serviceable material and disposal of unserviceable material within a lead as directed. |
| 160 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 m lead. |
| 161 | Dismantling of C.G.I. sheet roofing and stacking of serviceable material and disposal of unserviceable material within a lead as directed by the in-charge engineer. |
| 162 | Dismantling of existing wooden ceiling including stacking of serviceable material and disposal of unserviceable material as directed with all leads complete. |
| 163 | Dismantling wood work in frames, trusses, purlins and rafters up to 10 meters span and five meters height including stacking the material within 50 meters lead. |
| 164 | Dismantling of existing window shutters carefully without breakage including stacking within a lead as directed by the in-charge engineer. |
| 165 | Dismantling marble chips in flooring and skirting (excluding base course) including stacking of serviceable material and disposal of unserviceable material within a lead of 100 meter. |
| 166 | Demolishing cement concrete work, including disposal of unserviceable material within the campus as per directions of EIC 1:3:6 or richer mix. |
| 167 | Demolishing brick work in cement mortar up to floor V level including stacking of serviceable material and disposal of unserviceable material within the campus as per directions of EIC. |
| 168 | Demolishing of terrazzo flooring, tiles in floors and walls including plaster on walls including stacking of service able material and disposal of un-serviceable material as directed. |
| 169 | Demolishing of rubble stone masonry in cement mortar including stacking of serviceable material and disposal of unserviceable material within the campus as per directions of EIC |
| 170 | Aluminium Work. Providing and fixing Aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia. and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminum snap beading for glazing / paneling, C.P. brass / stainless steel screws,dashfastners,handles,hinges, all complete as per architectural drawings and the directions of Engineer-in-charge. (excluding Glazing, paneling, sliding channels/ sliding arrangement and other fittings complete) |
| 171 | Anodized aluminum (anodized transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) Using 2.5"x1.5" sections 1.5mm thick |
| 172 | Anodized aluminum (anodized transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) Using 4"x1.75" sections 1.5mm thick |
| 173 | Powder coated aluminum (minimum thickness of powder coating 50 micron)Using 2.5"x1.5" sections 1.5mm thick |
| 174 | Powder coated aluminum (minimum thickness of powder coating 50 micron)Using 4"x2" sections 1.5mm thick |
| 175 | Providing and fixing 12mm thick pre-laminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type loll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. |
| 176 | Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side. |
| 177 | Pre-laminated particle board with decorative lamination on both side |
| 178 | Providing and fixing glazing in aluminum door, window, ventilator shutters, and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminum snap beading shall be paid in basic item): |
| 179 | With float glass panes of 3.5 mm thickness |
| 180 | With float glass panes of 5.00 mm thickness |
| 181 | With float glass panes of 8 mm thickness |
| 182 | Providing and fixing of both sides pre-laminated ply board 12mm thick in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminum snap beading shall be paid in basic item): |
| 183 | Providing and fixing of lock for aluminium doors of approved make as per directions of EIC. |
| 184 | Providing and fixing of G-Channel,wheel sets,etc complete set for sliding door . |
| 185 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight up to 125 kg., for doors, including cost of cutting floors , embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. |
| 186 | With stainless steel cover/ brass plate minimum 1.25 mm thickness. |
| 187 | Hydraulic Door Closer |
| 188 | Providing and fixing powder coated aluminum work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminum angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminum perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm Centre to Centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in-charge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately). |
| 189 | Providing and fixing 6 mm dia. G.I. level adjusting hangers (up to 1200mm length), fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40x3mm size 60 mm long and stainless steel expandable dash fastener of 12.5 mm dia. and 50 mm long, complete as per direction of Engineer -in-charge. |
| 190 | Providing and fixing machine molded ACP covering of approved pattern & design, made out of machine cut aluminum sheet and machine holed for receiving dash fastener, over expansion joints on vertical surfaces/ceiling floors, the fixing on plate in one row on one side of joint only shall be done with stainless steel dash fasteners of 8 mm dia. and 75 mm long bolt including providing aluminum washers 2 mm thick & 15 mm dia. at a staggered pitch of 200mm Centre to Centre including drilling holes in the receiving surface and providing expandable plastic sleeves in holes etc. Including frame work complete as per direction of Engineer-in-charge. |
| 191 | ACP 3.5mm thick of required color |
| 192 | ACP 4.0mm thick of required color |
| 193 | Providing and laying G.S.B. grade including compacting, watering and consolidation with power road roller to the required gradient and camber including all carriages of material complete. |
| 194 | Providing and laying G.S.B. grade including compacting, ramming, watering and carriage complete. |
| 195 | Supplying and laying of stone soling hand packed tightly including ramming, watering and carriages complete. |
| 196 | Supplying and Filling earth, including carrying by lorry, placing, dressing and ramming in layers not exceeding 20cm in depth, breaking clods watering, rolling each layer with ½ tone roller or wooden or steel rammers, and rolling every 3rd and top-most layer with power road roller of minimum 8 tones, filling in ground depressions, Including of all carriages from source to site complete. |
| 197 | Engagement of tipper including fuel charges complete. |
| 198 | Engagement of excavator (JCB) in all terrains including fuel charges complete. |
| 199 | Engagement of hand cart |
| 200 | Providing and fixing of wardrobe, almirah, drawer locks(Sample to be approved by competent authority) |
| 201 | Providing and fixing of aluminum double channel with wheel set for sliding glass window of approved quality of following sizes. |
| 202 | 20 mm |
| 203 | 25 mm |
| 204 | Providing and fixing of door closer capsule type of standard make |
| 205 | Providing and fixing of door closer springtype of standard make |
| 206 | Providing and fixing of following fittings |
| 207 | Aldrop |
| 208 | Tower Bolt 100mm |
| 209 | Tower Bolt 150mm |
| 210 | Handle 100mm |
| 211 | Handle 150mm |
| 212 | I Hook |
| 213 | Hinges 75mm |
| 214 | Hinges 100mm |
| 215 | Lockable sliding Aldrop 250-300mm long (Godrej/ Link/Ramson or equivalent) |
| 216 | Providing and fixing bright finished 100mm mortice lock with 6 levers with pair of handles for aluminum doors of approved quality with necessary screws etc. complete as per direction of Engineer-in-charge |
| 217 | Manufacturing and fixing ofcomputer tables of required size and height of 19mm thick solid core ply sheet (Ply to Ply)exposed surface to be laminated with Dulmica sheeting including cost of key boards (readymade), racks drawers, cupboards, cost of brass knobs /locks of approved make and other necessary fittings and fixtures of approved quality and make. (Measurements be made on top surface only) |
| 218 | Manufacturing and fixing of computer tables of required size and height of 19mm thick both sides laminated board of specified brand (as per design and approved drawings) fitted with support keys, key boards( readymade), racks and drawers including cost of brass knobs /locks of approved make and other necessary fittings and fixtures of approved quality and make. (Measurements be taken on top surface only for payment) |
| 219 | Providing and fabrication of ward robes (ornamental) of approved quality 19mm Ply Sheet (Ply to Ply) in sides, shelves and wherever required including 6mm ply wood on back and 19MM pine board ply wood in shutters, inside and outside of shutters finished with Dulmica sheeting of approved quality and color on exposed face of approved design and drawings including painting two or more coats of synthetic enamel paint of approved quality and color inside including cost of following aluminum fittings and locks of approved make.15mm dia. M.S. pipe chromium plated with necessary brackets 4"-0" length and including all other necessary accessories complete in all respects. Including fixing with dashfasteners wherever required (For payments front face to be measured). |
| 220 | 50-60 cm deep |
| 221 | 40-45 cm deep |
| 222 | 20-30 cm deep |
| 223 | Providing and fabrication of ward robes (ornamental) of approved quality 19mm Ply sheet (Ply to Ply) in sides, shelves and wherever required including 6mm ply wood on back and providing and fixing of MDF shutters of approved quality, design and drawings including painting two or more coats of synthetic enamel paint of approved quality and color inside including cost of following aluminum fittings and locks of apprpoved make.15mm dia. M.S. pipe chromium plated with necessary brackets 4"-0" length and including all other necessary accessories complete in all respects. Including fixing with dashfasteners wherever required (For payments front face to be measured). |
| 224 | 50-60 cm deep |
| 225 | 40-45 cm deep |
| 226 | 20-30 cm deep |
| 227 | Supplying and fixing of rolling shutters of approved make made of M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 27.5 cm long wire springs grade No:2 and M. S. top cover of required thickness for rolling shutters (80x1.25mm M.S Laths with 1.25 mm thick top cover) |
| 228 | Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm and braced with flat iron diagonals 20x5 mm size with top and bottom rail of T-iron 40x40x6mm with 40mm dia, steel pulleys complete with bolts, nuts, locking arrangement, stoppers, handles, including applying priming coat of approved steel primer |
| 229 | Providing and fixing of water closet squatting pan (Indian type W.C. pan) with 100mm sand cast Iron P or S trap, 10 liter low level white PVC flushing cistern with manual controlled device (handle lever) confirming to I.S. 7231 with all fittings and fixtures complete including cutting and making good the walls and floors wherever required White vitreous china long pan pattern W, C. pan of size 580mm with integral type foot rests.(Jaquar/ Hindware/ Cera/ Kerrovit or equivalent) |
| 230 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white PVC flushing cistern with manual controlled device (handle lever) confirming to I.S. 7231with all fittings and fixtures complete including cutting and making good the walls and floors wherever required W.C. pan with ISI marked white solid plastic seat and lid. ((Jaquar/ Hindware/ Cera/ Kerrovit or equivalent) |
| 231 | Providing and fixing wash basinwith CI/MS/ brackets including painting of fittings and brackets, cutting and making good walls wherever required white vitreous china wash basin size 630x450mm with32mm dia. C.P. brass union & flexible waste pipe(Jaquar/ Hindware/ Cera/ Kerrovit or equivalent) |
| 232 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 233 | Providing and fixing of white vitreous china water closet squatting pan (Indian type) Orissapattern W.C. pan of size 580x440 mm (Jaquar/ Hindware/ Cera/ Kerrovit or equivalent) |
| 234 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS: 7231,with fittings and fixtures complete. 10 liters capacity- white(Sample to be approved by competent authority) |
| 235 | Providing and fixing solid plastic seat with lid for pedestal type W.C. pancomplete.(Sample to be approved by competent authority) |
| 236 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265mm size respectively. |
| 237 | Providing and fixing Salem stainless steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required. 610x510mm bowl depth 200mm. (Sample to be approved by competent authority) |
| 238 | Providing and fixing white vitreous china laboratory sink including making all connections excluding cost of fittings Size 600x450x200 mm. |
| 239 | Providing and fixing of white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm respectively with automatic flushing cistern with standard flush pipe and C.P brass spreaders with brass unions and G.I clamps complete including painting of fittings and brackets, cutting and making good the walls and floors wherever required One urinal basin with 5 liter white PVC automatic flushing cistern(Sample to be approved by competent authority) |
| 240 | Providing and fixing 600x450mm beveled edge mirror of specified brand mounted on 6mm thick plywood/hardboard including cost of wooden/PVC plugs and CP brass screws. |
| 241 | Providing and fixingbeveled edge mirror of specified brand mounted on 6mm thick plywood/ hardboard including cost of wooden/PVC plugs and CP brass screws. |
| 242 | Circular shape 450mm dia. |
| 243 | Rectangular shape 453x357mm. |
| 244 | Oval shape 450x350mm |
| 245 | Providing and fixing of C.P grating 100mm size. ISI |
| 246 | Providing and fixing of G.I pipes (class B pipes) complete with G.I fittings and clamps including cutting and making good the walls etc. internal work (Exposed on Walls)(Sample to be approved by competent authority) |
| 247 | 15mm dia. Nominal bore |
| 248 | 20mm dia. Nominal bore |
| 249 | 25mm dia. Nominal bore |
| 250 | 32mm dia. Nominal bore |
| 251 | 40mm dia. Nominal bore |
| 252 | 50mm dia. Nominal bore |
| 253 | Providing and fixing of G.I pipes (class B pipes) complete with G.I fittings including trenching and refilling etc. (external work)(Sample to be approved by competent authority) |
| 254 | 15mm dia. Nominal bore |
| 255 | 20mm dia. Nominal bore |
| 256 | 25mm dia. Nominal bore |
| 257 | 32mm dia. Nominal bore |
| 258 | 40mm dia. Nominal bore |
| 259 | 50mm dia. Nominal bore |
| 260 | 65mm dia. Nominal bore |
| 261 | 80mm dia. Nominal bore |
| 262 | 100mm dia. Nominal bore |
| 263 | Providing & Fixing GI pipes (C-Class) complete with GI fittings and clamps including making good the walls etc. concealed pipe including painting with anti-corrosive bitumastic paint, cutting chases and making good the wall. (Sample to be apprpoved by competent authority) |
| 264 | 15mm dia. Nominal bore |
| 265 | 20mm dia. Nominal bore |
| 266 | Providing and fixing of following G.I. fittings. 15 mm nominal bore.(Sample to be approved by competent authority) |
| 267 | Elbow |
| 268 | Tee |
| 269 | Union |
| 270 | pvc plug/ G.I Plug |
| 271 | Nipple |
| 272 | 50mm long. |
| 273 | 75mm long |
| 274 | 100mm long |
| 275 | 150mm long |
| 276 | Socket |
| 277 | 15mm |
| 278 | 20mm |
| 279 | 25mm |
| 280 | Reducer |
| 281 | 15mm-20mm |
| 282 | 20mm-25mm |
| 283 | 20mm-32mm |
| 284 | 25mm-32mm |
| 285 | Providing and fixing of following G.I. fittings.20 mm nominal bore.(Sample to be approved by competent authority) |
| 286 | Elbow |
| 287 | Tee |
| 288 | Union |
| 289 | pvc plug/ G.I Plug |
| 290 | Nipple |
| 291 | 50mm long. |
| 292 | 75mm long |
| 293 | 100mm long |
| 294 | 150mm long |
| 295 | Providing and fixing of PVC connection with C.P. brass unions |
| 296 | 300mm long. |
| 297 | 450mm long |
| 298 | 600mm long |
| 299 | Providing and fixing ball valve (brass) of approved quality complete (Sample to be approved by competent authority) |
| 300 | 15mm dia. |
| 301 | 20mm dia. |
| 302 | 25mm dia. |
| 303 | 40mm dia. |
| 304 | Providing and fixing gate valve (brass) of approved quality complete (Sample to be approved by competent authority) |
| 305 | 15mm dia. |
| 306 | 20mm dia. |
| 307 | 25mm dia. |
| 308 | 40mm dia. |
| 309 | 50mm dia. |
| 310 | Providing and fixing of Ball cock of approved quality and make with plastic float. (PVC type) |
| 311 | 15 mm |
| 312 | 20 mm |
| 313 | Providing and fixing of Ball cock of approved quality and make without plastic float. |
| 314 | 15 mm |
| 315 | 20 mm |
| 316 | Providing and placing on terrace (at all floor levels) polythene water storage tank ISI:12701 mashed indicating the BIS license No. with cover and suitable locking arrangements and making necessary holes for inlet, outlet and overflow pipes but including all required tankey nipples and excluding the base support for tank (Syntax/Comfort or equivalent having valid ISI license) complete |
| 317 | Construction of plateform for W.C. with brick masonry in cement mortar 1:6 mix. Including filling of sand and providing of 15mm cement plaster in 1:4 mix. |
| 318 | Providing and fixing of C.P. Cups for C.P. fittings. |
| 319 | Providing and fixing of C.I. manhole cover heavy duty of following sizes. |
| 320 | 12"x12" |
| 321 | 18"x18" |
| 322 | 24"X24" |
| 323 | Providing and fixing of water heater (geysers) (Havells/ Hindware/ Jaquar/ Venus or equivalent) including cost of dash fasteners with nuts and washers |
| 324 | 60 Litre |
| 325 | 50 Litre |
| 326 | 40 Litre |
| 327 | 35 Litre |
| 328 | 25 Litre |
| 329 | Providing and fixing of Chromium plated brass tube for wash basins and geysers etc. |
| 330 | 45 cm in length |
| 331 | 60 cm in length |
| 332 | Providing and fixing Geyser elements (as per Geyser type) |
| 333 | Providing and fixing Geyser thermostat |
| 334 | Providing and fixing Drain plug with washer. |
| 335 | Providing and fixing Safety valve for geysers. |
| 336 | Providing and fixing water washers for geysers. |
| 337 | Providing and fixing of auto thermo cut for geyser. |
| 338 | Providing and fixing of Bajaj brass/wet type element for water geyser as per Geyser Type |
| 339 | Providing and fixing of matte cover for geyser. |
| 340 | Providing and fixing of pressure water ball Valve |
| 341 | Providing and fixing of C.P. Swan cock 3 way of approved quality. |
| 342 | Providing and fixing of C.P Laboratory Swan cock 3 way (Tall) of approved quality. |
| 343 | Providing and fixing C.P. brass bib cock of approved quality (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) 15mm nominal bore with flange |
| 344 | Providing and fixing of 15mm size chromium plated cast brass pillar cock of approved quality(Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) |
| 345 | Providing and fixing of 15mm size chromium plated cast brass angle valve of approved quality (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) with wall flange |
| 346 | Providing and fixing of 15mm size chromium plated cast brass wash basin mixer (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) |
| 347 | Providing and fixing of 15mm size chromium plated cast brass sink mixer of approved quality.(Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) |
| 348 | Providing and fixing of 15mm size chromium plated cast brass wall mixer Non telephonic with lead of approved quality. (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) withflange |
| 349 | Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge.15 mm nominal dia(Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) |
| 350 | Providing and fixing C.P Head Showerof different sizes with arm (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) |
| 351 | Providing and fixing telephonic chain for wall mixer (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) |
| 352 | Towel ring 20mm dia. (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent)withflange |
| 353 | Towel rod (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) |
| 354 | Soap Dish holder/ Toilet Paper Holder |
| 355 | Providing and fixing 600mmx120mmx5mm glass shelf with edges round of supported on anodized aluminum angle frame with C.P. brass brackets and guard rail complete fixed with 40mm long screws, rawl plugs etc. complete. |
| 356 | C.P./PVC Long bends of required size of approved quality. |
| 357 | C.P. Waste for wash basin of approved quality |
| 358 | Providing and fixing of pvc manhole cover of approved make of following sizes. (Heavy type) |
| 359 | 12"x12" |
| 360 | 18"x18" |
| 361 | 24"X24" |
| 362 | Construction of soakage pit by way of earth work in excavation including providing and fixing of pre-cast cement concrete rings 0.90 mtr dia. of specified thickness and 200-250 mm wide including all carriages complete. Including disposal of excavated earth within the campus as directed by EIC. |
| 363 | Providing and fixing of pre-cast cement concrete lid for soakage pit of specified size and thickness. |
| 364 | Construct brick masonry man hole in cement mortar 1:4 (1 cement: 4 coarse sand) RCC top slab with 1:2:4 mix (1 cement : 2 Coarse sand : 4 graded stone aggregate 20mm nominal size) foundation concrete (1:4:8) inside plastering 12mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished with floating coat of neat cementand making channel in cement concrete 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal sizefinished witha floating coat of neat cement complete. (Depth as per site requirement) |
| 365 | Inside size 90 x 90 cm deep including RCC/C.I. manhole cover medium duty with frame of size 60x60mm size/ Concrete Slab. With F.P.S. bricks with class designation 75 and with crushed stone aggregate complete in all respects. |
| 366 | Inside size 60 x 60 cm deep including RCC/C.I. manhole cover medium duty with frame of size 60x60mm size/ Concrete Slab. With F.P.S. bricks with class designation 75 and with crushed stone aggregate complete in all respects. |
| 367 | Inside size 45 x 45 cm deep including RCC/C.I. manhole cover medium duty with frame of size 45x45mm size/ Concrete Slab. With F.P.S. bricks with class designation 75 and with crushed stone aggregate complete in all respects. |
| 368 | Providing and fixing of PVC pipe (Type "B") in proper gradient in excavated trenches including jointing and refilling the excavated material complete including cost of excavation. (Sample to be approved by competent authority) |
| 369 | 150mm dia. Pipe (Including necessary fittings) |
| 370 | 100mm dia. Pipe |
| 371 | 75mm dia. Pipe |
| 372 | 50mm dia. Pipe |
| 373 | Providing and fixing of the following PVC fittings. (Sample to be approved by competent authority) Plain bend. |
| 374 | 100mm |
| 375 | 75mm |
| 376 | Collar |
| 377 | 100 mm |
| 378 | 75 mm |
| 379 | Door Bend |
| 380 | 100 mm |
| 381 | 75 mm |
| 382 | Door Tee |
| 383 | 100 mm |
| 384 | 75 mm |
| 385 | Plain Tee |
| 386 | 100 mm |
| 387 | 75 mm |
| 388 | Door Junction Four Way |
| 389 | 100 mm |
| 390 | 75 mm |
| 391 | Plain Junction Four Way |
| 392 | 100 mm |
| 393 | 75 mm |
| 394 | Floor Trap |
| 395 | 100 mm |
| 396 | 75 mm |
| 397 | Providing and fixing of Health Faucet / jet spray with plastic flexible pipe 8 mm dia, 1.5 m long, wall hooked complete as required, including necessary Accessories , installation charges and complete in full respect as per the directions of Engineer- in-charge. |
| 398 | Providing and fixing Brass bib cock of approved quality 15mm nominal bore. |
| 399 | Providing and fixing spindle 15mm dia. All types like washer type/disc type etc. |
| 400 | Providing and fixingMixer leg set (Sample to be approved by competent authority) |
| 401 | Providing & Replacing of Siphon to flushing cistern(Sample to be approved by competent authority) |
| 402 | Providing & Replacing of washer to Siphon of flushing cistern |
| 403 | Providing & Replacing of handle to Siphon of flushing cistern |
| 404 | Providing & Replacing of ball cock of flushing cistern without float |
| 405 | Providing & Replacing of ball cock of flushing cistern with float |
| 406 | Providing & fixing of polycarbonatesheets of approved make |
| 407 | Corrugated type |
| 408 | Plain Type |
| 409 | Providing & fixing of pvc panelling 6mm thick of approved make including all related acessories like corner/topflashing, etc complete including grounds, including fixing,screwing complete |
| 410 | Providing & fixing wallpaper of approved pattern & quality to wall surface including chemical & adhesive as per directions of EIC |
| 411 | Providing & fixing curtain rod with brackets, knobs complete job |
| 412 | Touchwood polishing,two or more coats on wood work including pressing of nails,scrapping with emery paper, a coat of wood filler & fevicol washing complete as per directions of EIC on new wood work. |
| 413 | Touchwood polishing,two or more coats on wood work including a coat of wood filler & fevicol washing complete as per directions of EIC.also including removing of old existing finishing by proper scrapping with sanding/emery paper as per directions of EIC. |
| 414 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings, adaptors etc. This includes testing of joints complete as per direction of Engineer incharge.Internal work Concealed fixing the pipe etc. (Sample to be approved by the competent authority) |
| 415 | Internal work Concealed fixing the pipe ......etc. PN-16 pipe , 25mm OD |
| 416 | Internal work Concealed fixing the pipe ......etc. PN-16 pipe , 32mm OD |
| 417 | Internal work exposed on wall with clamps ......etc. PN-16 pipe , 25mm OD |
| 418 | Internal work exposed on wall with clamps ......etc. PN-16 pipe , 32mm OD |
| 419 | Internal work exposed on wall with clamps ......etc. PN-16 pipe , 40mm OD |
| 420 | Internal work exposed on wall with clamps ......etc. PN-10 pipe , 50mm OD |
| 421 | External work including trenching, refilling etc. PN-16 pipe , 25mm OD |
| 422 | External work including trenching, refilling etc. PN-16 pipe , 32mm OD |
| 423 | External work including trenching, refilling etc. PN-16 pipe , 40mm OD |
| 424 | External work including trenching, refilling etc. PN-10 pipe , 50mm OD |
| 425 | External work including trenching, refilling etc. PN-16 pipe , 63mm OD |
| 426 | Providing and fixing PPR Unions(Sample to be approved by competent authority) |
| 427 | for 25mm dia. |
| 428 | for 32mm dia. |
| 429 | for 40mm dia. |
| 430 | for 50mm dia. |
| 431 | for 63mm dia. |
| 432 | Providing and fixing PPR ball valves (Sample to be approved by competent authority) |
| 433 | for 25mm dia. |
| 434 | for 32mm dia. |
| 435 | for 40mm dia. |
| 436 | for 50mm dia. |
| 437 | for 63mm dia. |
| 438 | Providing and fixing of thermal insulation over following dia G.I Pipes at all heights |
| 439 | for 15mm dia. |
| 440 | for 20mm dia. |
| 441 | for 25mm dia. |
| 442 | for 40mm dia. |
| 443 | Providing and fixing C.P. two way brass bib cock of approved quality ((Sample to be approved by competent authority) 15mm nominal bore |
| 444 | Providing & fixing G.I chainlink fencing of approved size 50mmx50mm (3.15mm thick) including necessary bolts,welding etc complete |
| 445 | Providing and Laying Red Stone For dedo,flooring,Landings of staircase, etc. usingred stone ofminimum thickness 18 mm machine-cut slabs of approved quality, type & colour as per the approved sample, including cutting to required sizes, shapes and pattern as per drawing, and laying to the required level / slope including all surface preparation, providing and laying cement mortar (1:4) bed of average thickness 25 mm with cement slurry / pastespread on the top of mortar using grey cement,filling and finishing the joints with neat cement slurry/ white cement with matching colour pigment, curing, mirror polishing of joints if required, cleaning etc. complete at all floors and levels as per the instructions ofthe EIC.The Contractor shall arrange for storage of all related materials at site, handling, shifting and lifting at work location. |
| 446 | Providing & fixing various sizes of 15mm CP Nipples |
| 447 | Prividing & fixing of Water Booster pumps (Sample to be approved by competent authority) |
| 448 | 0.5 hp |
| 449 | 1.0 hp |
| 450 | 1.5 hp |
| 451 | 2.0 hp |
| 452 | Providing and fixing of 450-600 mm long Washbasin connection nozzleend |
| 453 | Providing and fixing of Vertical blinds of required coloras approved by EIC |
| 454 | Providing and fixing of roller blinds of required pattern/coloras approved by EIC |
| 455 | Repairs, rewinding of all types of Water Booster pumps, submersible pumps at various locations/ campuses including replacement of allied damaged/ wornout spares complete job including necessary repairs |
| 456 | 0.5-1.0 H.P |
| 457 | 1.5-2.0 H.P |
| 458 | 3-6 H.P |
| 459 | 7.5-10 H.P |
| 460 | 11-15 H.P |
| 461 | Lifting, dismantling and reassembling including lowering and refixing of submersible pump in bore holes including related works up to all depths (like errecting of tripods, pulleys, wires etc) |
| 462 | For G.I pipesup to 25mm dia |
| 463 | For G.I pipes32 to 100mm dia |
| 464 | Supply, installation, testing and commissioning of Tube well Submersible pump for water supply |
| 465 | 1.0 hp |
| 466 | 1.5 hp |
| 467 | Supplying and fixing of Suitable rating common electrical starter |
| 468 | Any other item not covered in this BOQ but present in JKSSR 2022 shall be paid accordingly but at the same percentage as quoted by the bidder |
| 469 | Note. The quoted percentage (%age) should preferably be in fractional form in order to minimize concurrence of similar quoted rates |
Copyright © 2023 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
