Tender For Construction Of Repair And Renovation Work Of Homeopathic Hospital At Visham Block Mohammadpur District Azamgarh (U.P.)
Tender Value
11.40 Lakhs
Estimated cost
Bid Submission
27 Mar 2023
0 days left
EMD
23000
Bank guarantee accepted
Document Fee
5900
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
mohammadpur → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Repair And Renovation Work Of Homeopathic Hospital At Visham Block Mohammadpur District Azamgarh ( U.P. )
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 25-Mar-2023 | Corrigendum | Other | 27-Mar-2023 |
BOQ
| Sl. No. | Item Description |
| 1 | Civil Work |
| 2 | Dismantiling Existing plaster including disposal of refuse as directed by the Engineer-in charge with in a distance of 60metre (200ft) outer side |
| 3 | 12mm cement plaster in single coat on fair side of single or half brick wall for exterior plastering up to floor two level including internal rounded angles chamfers, and/or roundedangles not exceeding 80mm in girth and finished even and smooth no extra for mixing any additive. 1 cement : 6 Coarse sand. |
| 4 | 12 mm cement plaster in single coat on rough side of single or half brick wall for interior plastering up to floor two level including internal rounded angles not exceeding 80 mm in girth and finished even and smooth. (1) 1 cement : 6 Coarse sand |
| 5 | Dismantling cement concrete or brick or granolithic floor including baseconcrete and including stacking of dismantled materils as directed by the engineer charge stone flagged or tlied floor |
| 6 | Demolishing mud phaska in terracing and disposal of material within 50 metres lead. |
| 7 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm |
| 8 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm |
| 9 | Supply and fixing 6mm thick china white glazed tiles in flooring or in skirting or dado laid with 1:3 cement and approved coarse sand mortar finished with white cement slurry jointing and polishing complete including supply of all materials, labour and tool sand plants etc. |
| 10 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade. New work (Two or more coats applied @ 1.43 ltr/10 sqm. over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm). |
| 11 | Distempering (Two coat) with oil bound distemper of approved brand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as Berger,J&N, Shalimar, Asian paints after thoroughly brushing the surface free from mortar droppings & other foreign matters & also including preparing the surface even with plaster of paris or approved synthetic material & sand papered smooth including cost ofall materials. |
| 12 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 13 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 14 | Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides |
| 15 | Providing & fixing Stainless steel sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc complete. (a) 250mm x 16mm . |
| 16 | Providing and fixing stainless steel towerbolts (barrel type) with necessary screws etc. complete. (a) 250mmx10mm |
| 17 | Providing and fixing stainless steel handles with screws etc. complete (a) 150 mm |
| 18 | Providing & fixingglass panes with putty and glazing in steel doorswindows, clerestory windows, all complete with :4 mm thick glass panes |
| 19 | Painting two coat over priming coat (but including cost of priming coat) on steel and other metal surfaces up to 10 cm. width or girth or small articles not exceeding 0.10sqm in area white superior synthetic enamel such as LUXOL3 apcolite superlac, DULUX specified brushing to give an even shade and including cleaning the surface of all dirt,dust and other foreign matter sand papering and stoping including cost of all materials, labour tools and plants etc. required for proper completion of the work. |
| 20 | Painting two coat over priming coat (but including cost of priming coat) on new wood surface. up to 10 cm. width or girth or small articles not exceeding 0.10sqm in area white superior synthetic enamel such as LUXOL3 apcolite superlac, DULUX specified brushing to give an even shade and including cleaning the surface of all dirt,dust and other foreign matter sand papering and stoping including cost of all materials, labour tools and plants etc. required for proper completion of the work. |
| 21 | Providing and laying \"brick coba\" 120 mm thick laid with M-150 class brick bat coba 7.50cm thick with gap of 15mm to each other, over 20 mm thick base of cement mortar 1:4 cement and coarse sand mixed with water proofing compound spreading cement slurry mixed with acrelic cement concrete water proofing compound filled gaps of coba & top of coba mortar mixed with water proofing compound in 1:4 cement & coarse sand mortar finised smooth & top mashed false square 30 cm x 30 cm & side wall parapet shall be mono lythic plaster wall up to 30 cm higher and junction & corner shall be rounded by brick ballast cement & coarse sand masonany Coba with top finised plaster mixed with acetic water proofing compound @ 2% by weight & including s/o all material, labour, T& P etc complete for proper completion of work. |
| 22 | Cement concrete flooring 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 12-20mm nominal size laid in one layer neat cement (25 mm thick floor). |
| 23 | Providing and laying in cement concrete 1:4:8 (1 cement :4 coarse sand :8 graded stone aggregate 40 mm nominal size) and curing complete,including cost of form- work,in foundation and floors. |
| 24 | Chequerred precast cement concrete tiles 20 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). |
| 25 | Ordinary cement without any pigment |
| 26 | S/O Hand rail and balustrade modular system passive SS-304 grade decorative railing system comprising of hand rail 50mm and 1mm thick and 3 No Horizontal steel pipe of 19mm dia and 1.5mm thick of equal spacing with balustrade to SS pipe of 38mm and 1.5mm thick @ 1200mm C/C of passivated SS 304 grade and fix duly on the floor with specially rivet expansion bolt and finish the surface foor and covering with steel show with all visible stainless metal of 304 grade in satin finish hight of railing is 900mm as per detailed specification. |
| 27 | Electrical Work |
| 28 | Wiring point for light with 1.0 sq.mm FR P.V.C. insulated multistrandsingle core Copper Conductor cable in P.V.C. conduit pipepartly concealedin wall&partlylaidin slab along with the reinforcement before concreting complete with 1.5 sq mm FR P.V.C. insulated multistrandsingle core Copper Conductor cable as earth wire drawn inside &piano typeswitch and ceiling rose/angle/batten holder on 3 mm thick phinolic laminated backelite sheet etccomplete in all respects as directed including matching colour wash. |
| 29 | Same as in item no. 1 but for fan. and light duty exhaust fan |
| 30 | Same as in item no. 1butfor 5ampplug point with piano type switch & socket etc. |
| 31 | Same as in item no.1 but for call bellwith piano type switch or socket etc. |
| 32 | Add for light / fan points with modular type switch in place of piano type switch. |
| 33 | Add for 2 way light point with modular switches in place of piano type switches. |
| 34 | Add for HPMV/Exhaust fan point with modular typeswitch in place of piano type switch. |
| 35 | Add for plug point with modular switch & socket in placem of piano type switch & socket. |
| 36 | Add for Call bell point with modular type bell push inplace of piano type bell push. |
| 37 | Supply and wiring of submain 2 number 4 sqmm . FR PVC insulated 1100 V grade multistranded single core copper conductor cable in heavy duty 20mm dia PVC conduit partly concealed in wall and partly laid in slab along with one number 2.5 sqmm FR PVC insulated multistranded copper conductor |
| 38 | cable as earth contunity wire etc. complete in all respects. |
| 39 | Supply and wiring of submain with two number 6 sq. mm. FRLSH PVC insulated 1100 V grade multistrand single core aluminium conductor cable in 20 mm dia heavy guage rigid steel conduit partly concealed in wall and partly laid in slab alongwith reinforcement before concreting, with one number 14 SWG copper earth continuity wire including matching colour wash etc. complete in all respect. As in item no. 222 (B) but in 25 mm dia heavy duty (2 mm thick) PVC conduit with one number 4 sq. mm. FRLSH PVC insulated multistrand copper conductor cable as earth continuity wire drawn in conduit. |
| 40 | Supply and fixing of batten / angle holder complete in all respect. |
| 41 | Supply and fixing of recess/ Surface/ Pendent mounting round 6 Watt 8 Watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect. CAT- AAA |
| 42 | Supply and fixing of recess mounting round 15 to 18 Watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect. CAT- AAA |
| 43 | Supply and fixing of LED Tube Light with batten suitable for up to 1 X 22 watt LED tube light fitting including tube on Surface complete in all respect. CAT- AAA |
| 44 | Supply and fixing of call bell of approved make on polished MDFEG/ Teak ply board including making connections etc. complete in all respect. |
| 45 | Supply and fixing of buzzer on polished MDFEG / Teak ply board including making connections etc. complete in all respect. |
| 46 | Supply and burying of 40mm dia x 4.5 metres long G.I. Pipe vertically for earthing having 12mm dia. Holes spaced 75mm apart drilled up to 2 metre from the bottom complete with earthing lead of No. 6 to 8SWG GI wire in G.I. Pipe up to appron (and from appron to switch board the cost of G.I. wire and pipe will be extra) upto switch board, 30cm square C.I. box with hinged cover masonary enclosure, funnel at top, alternate layers of charcoal/coke and salt at least 150mm thick alround etc. as per directions of Engineer-in-charge complete in all respects as per drawing. |
| 47 | Supply and laying of 25mm x 3mm G.I. strip from earth electrode directly in the ground as required complete in all respect. |
| 48 | Supply & Fixing of two number 8 SWG G.I wire for earthing purpose as required complete in all respects. |
| 49 | S&F of 6 Amp to 32 Amp. SPMCB (10 KA) C Curve |
| 50 | 5 - 32 amps. CAT- A |
| 51 | S&F of 6 Amp. to 32 Amp. DP MCB (10 KA) C Curve. CAT A |
| 52 | S&F of 63 Amp. 4 pole MCB(10 KA) C Curve. CAT A |
| 53 | S & F surface/Flush mounting 6ways TPN distribution board with additional metal door without MCB complete in all respect, as directed at site by Engineer in charge.CAT A |
| 54 | S & F surface/Flush mounting 12 ways SPN distribution board with additional metal door without MCB complete in all respect, as Direct by Engineer in Charge. CAT A |
| 55 | Supply and fixing of crimping, solderless, copper tin electroplated lugs of Dowells/Ismail make suitable for 1.5 sq.mm to 2.5 sq.mm cables, including tapping with insulating tape, complete in all respect. |
| 56 | S&F single pole MCB blanking plate. CAT B |
| 57 | Supply and fixing of power plug with 20 Amp./250 volt flush type modular switch and 5 pin 20 A/250 volt flush type universal modular socket switch on concealed M.S box including supply of all material, labour T&P etc. required for proper completion of work. |
| 58 | Erection and testing of ceiling fan and regulator for room height upto 3.5 metres including supply of 3mm thick G.I.Pipe19mm dia. Duly painted, complete in all respect. |
| 59 | Erection and testing of exhaust fan on the existing hole with suitable size of rag bolts, nuts and washers etc., complete in all respect. |
| 60 | Making hole in the wall for exhaust fan and finishing properly complete in all respect. |
| 61 | Supply and fixing hexagonal/Round G.P.fan box of approved make made up of 1.0 mm thick ISI Marked G.P.sheet spot welded Four to Eight holes of 25.4 mm for pipe entry of the box. Holes should be semi-shuttered type with 0.5 mm G.P. Sheet made upper & lower cover duly screwed fitted with 300 mm round zink coted M.S Bar X 12 mm & brand name should be embossed. Fixing with wiring conduit laid in the R.C.C. roof before concreting alongwith supply of all material, labour, T&P etc. required for proper completion of the work. |
| 62 | Supply and fixing of electronic fan regulator 120-280 V. ISI marked, on the existing switch board including making connections, required material, labour T&P etc. for proper completion of work to the satisfaction of Engineer in charge of work. |
| 63 | Supply and erection of AC 1200 mm Sweep 230/250 Volts , 50Hz ceilling fan with regulator standar down rod, blades including connection etc. complete as required. |
| 64 | Supply and fixing of 300 mm sweep ventilating (Medium heavy duty) exhaust fan complete with metallic blade (Steel bird guard protector/double ball bearing/ copper motor/ capacitor etc) |
| 65 | Supply and fixing danger board fabricated from 10 gauge M.S. Sheet as per I.E. Rules. |
| 66 | Supply and laying of 1800mm x 900mm x 12mm thick chequered rubbbber matting of tested quality. |
| 67 | S&F of 63 Amp. four pole change over switch on 40mm x 40mm x 6mm angle iron frame, including the cost of labour,T&P, painting and other material required for proper completion of the work as per direction and satisfaction of Engineer in charge. |
| 68 | Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. |
| 69 | 2 Pair |
| 70 | Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required. |
| 71 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.Telephone socket outlet |
| 72 | Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. |
| 73 | 75 mm X 75 mm X 60 mm deep |
| 74 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. |
| 75 | 1 or 2 Module (75mmX75mm) |
| 76 | Plumbing Work |
| 77 | Providing & fixing white vitereous china water closet squatting pan ISI marked (Indian type W.C. pan) with 100mm sand cast iron P or S trap, 10/12.5 litrsPVC low level flushing cistern with fittings & brackets 40mm dia C.P. flush pipe with fitting & clamps, 20mm over flow pipe with specials and mosquito proof coupling of approved municipal design, painting wherever required including cutting & making good the walls & floors where required. |
| 78 | Orissa Pattern W.C. pan of size580x 440mwith integral type foot rests flush pipe and over flow arrangement. |
| 79 | Providing & fixing white vitreous china wash basin with C.I. brackets painted white, 15mmbrass pillar taps, brass chain with rubber plug, 32mmbrass waste of standard pattern including cutting & making good the walls wherever required. |
| 80 | a) Flat back wash Basin size 550x400 mm with single 15mmbrass pillar tap. |
| 81 | Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete. |
| 82 | 32 mm dia |
| 83 | Providing & fixing 600x450mm bevelled edge mirror of superior glass (of approved quality) complete with 6mm thick asbestos cement sheet ground fixed to wooden cleats with C.P. brass screws and washers. |
| 84 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 85 | 15 MM nominal bore |
| 86 | Providing and Fixing C.P brass Abulation health faucet assembly with 1.0 m long braided PVC hose with mounting brackets fixed on wall complete. [FOR EWC] |
| 87 | Providing and Fixing C.P. brass Two-way angle valve for EWC points & for fixing Abulation Health Faucet of approved quality conforming to IS:8931 15mm nominal bore |
| 88 | Supplying & Fixing of CP soap tray fixed to the wall with PVC rubber plug with CP brass screws- Make -ESSCO AEC=1131 |
| 89 | Supplying & Fixing of Soap Dispensers |
| 90 | Supplying & Fixing of Soap Dispensers |
| 91 | Supplying & Fixing of dryer |
| 92 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, |
| 93 | 110 mm diameter |
| 94 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. |
| 95 | 110 mm |
| 96 | Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. |
| 97 | Providing, Fixing, jointing and testing in position of ISI marked UV stabilized UPVC pipes for soil, waste, and vent, Type-B as per IS:13592 suitable for rubber ring joints for horizontal pipes including all necessary specials and fittings (confirming to IS:14735) i.e, bends tees junctions (with or without doors). reducers WC connectors, couplers, cowels, clamps & hangers rubber rings, clean outs etc. fixing at wall/ ceiling/ floor level supported by clamps & hangers etc. inside duct / suspended from floor under false ceiling for proper completion of the work. The rubber ring shall confirm to IS:5382 (Make :Supreme /Finolex / Prince) (Pipe support: Intellotech / Easyflex / Chilly. |
| 98 | The Pipes will be supported by either rubber lined G.I. U strip clamps on 50X50X5 mm MS slotted angle duly painted (for a group of pipes) or G.I. rubber lined split clamp (for independent pipes). The cost will include all supported arrangements. The Work includes cutting holes in wall/ floor/ slabs and making good the same with cement concrete 1:2:4 complete as required. The work include commissioning of all pipes lines as per drawings and specification and as directed by engg. in. |
| 99 | 110 mm dia |
| 100 | 75 mm dia |
| 101 | Providing & Fixing UPVC Floor trap of self cleaning design with CP Jali complete in all respects. (Make : Supreme / Finolex) |
| 102 | 110 X 110 mm P-Type |
| 103 | Providing and fixing on wall face unplasticised PVC moulded fittings / accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. |
| 104 | Reducing Tee 100X100X75mm |
| 105 | Door Tee |
| 106 | 110X110X75mm |
| 107 | 75X75X75mm |
| 108 | Bend |
| 109 | 110 mm |
| 110 | 75 mm |
| 111 | Terminal guard |
| 112 | 110 mm |
| 113 | 75 mm |
| 114 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. |
| 115 | (Internal Work) |
| 116 | Expansion on Wall |
| 117 | 32 mm dia nominal bore. (medium duty) |
| 118 | Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work. |
| 119 | 32 mm diameter pipe. |
| 120 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. |
| 121 | 25 mm nominal outer dia Pipes |
| 122 | 40 mm nominal outer dia Pipes |
| 123 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. |
| 124 | 15 mm nominal outer dia Pipes |
| 125 | 20 mm nominal outer dia Pipes |
| 126 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 |
| 127 | 15 mm nominal bore |
| 128 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. |
| 129 | 15 mm nominal bore |
| 130 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 |
| 131 | 15mm nominal bore |
| 132 | Providing and fixing gun metal gate valve with C.I. wheel of approvedquality (screwed end) |
| 133 | 25 mm nominal bore |
| 134 | 32 mm nominal bore. |
| 135 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : |
| 136 | 25 mm nominal bore |
| 137 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 138 | Providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to ISI : 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. The base support i/c fittings & fixtures for tank shall be paid separately. |
| 139 | Soak pit |
| 140 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks of class designation 75 and S.W. drain pipe 100 mm diameter, 1.8m long complete as per standard design. With F.P.S. bricks |
| 141 | Yoga Platform |
| 142 | Excavation of foundation in ordinary soil (loam clay or sand) including lift upto 1.50 meter and lead upto 30 meter and including filling, watering and ramming of excavated earth into the space between the building and sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the Engineer incharge up to a distance of 30 meters from the foundation trenches including all T & P phowarah and basket etc complete. |
| 143 | Carted Earth filling. |
| 144 | Sand filling |
| 145 | Providing and laying in cement concrete 1:4:8 (1 cement :4 coarse sand :8 graded stone aggregate 40 mm nominal size) and curing complete,including cost of form- work,in foundation and floors. |
| 146 | Providing andinjectingchemical emulsion for preconstructionalantitermite treatment andcreatinga chemical barrier underand alroundthe column pits wall trenches basement excavation top surface if plinth filling junctionofwall and floor, alongthe external perimeter ofbinding expansionjoints, surroundings ofpipes andconduits etc, complete (plinth area of the building at groundflooronly shall be measured as per I.S.6313 (Part II 1981) Alderine emulsifiable concentrate or anyotherapproved materialsuch as Heptrachlor or chlordance will be used. Therateofapplicationofchemical emulsion shallbe asfollows : (1)Treatment for masonary & foundation 5 liters per sqm.(2) Back fill inimmediate contract with foundation 7.5 liters/sqm (3) Treatment of topsurfaceof plinth. filling 5 litres per sqm (4)Treatmentofsoilalong externalperimeter of building 7.5 liters/sqm.(5) Treatment of soil under apronalong external perimter 5 liters/ sqm. |
| 147 | R.C.C. work with cement approved coarse sand and 20 mm. guage approved stone grit im the proportion of 1:1.5:3 in lintels of doors and windows excluding supply of reinforcement and its fixing and binding the same with 24 BWG binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works. strength of the concrete shall not beless than M-20 |
| 148 | As in item no. 6 above but for R.C.C. work in footing/raft (Using 1:1.5:3 Mix concrete) M-20 |
| 149 | As in item no. 6 above but for R.C.C. work in Column (Using 1:1.5:3 Mix concrete) M-20 |
| 150 | P/F TMT Fe500 or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. |
| 151 | Providing and laying damp-proof course 20mm thick with cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 12.5mm nominal size) |
| 152 | Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. |
| 153 | Class M-150 brick work in 1:6 cement and coarse sand of 1.25 F.M. mortar in foundation and plinth including supply of all materials, labour, tools and plants etc. required for proper completion of the work. (1:6 cement & coarse sand) |
| 154 | 12 mm cement plaster in single coat on rough side of single or half brick wall for interior plastering up to floor two level including internal rounded angles not exceeding 80 mm in girth and finshed even and smooth. (1) 1 cement : 6 Coarse sand |
| 155 | Distempering(Two coat) withoil bound distemper of approvedbrand and manufacture&ofrequired shadeon undecorated wall surface to give an even shade over &includingapriming coat with cement primer of approvedbrand& manufacture such as Berger,J&N, Shalimar Asian paintsafterthoroughly brushing the surface free from mortar droppings & other foreign matters& alsoincluding preparing the surfaceeven with plaster of paris orapproved synthetic material &sand papered smooth including cost of all materialsalso Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete..[Inside walls] |
| 156 | Painting two coat over priming coat (but including cost of priming coat) on steel and other metal surfaces up to 10 cm. width or girth or small articles not exceeding 0.10sqm in area white superior synthetic enamel such as LUXOL3, Hi-gloss apcolite superlac, DULUX specified brushing to give an even shade and including cleaning the surface of all dirt, dust and other foreign matter sand papering and stoping including cost of all materials, labour tools and plants etc. required for proper completion of the work |
| 157 | 40mm thick 1:2:4 plain cement concrete floor (1 cement :2 coarse sand :4 graded stone aggregate 12-20mm nominal size laid in one layer neat cement. |
| 158 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 159 | Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 160 | Extra for providing and fixing wind tiesof 40x6 mm flat iron section |
| 161 | Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete. 0.80 mm thick with zinc coating not less than 275 gm/m² |
| 162 | Boundary Wall |
| 163 | Class 150 brick work in1:3 cement and corse sandof2.25fineness modulus mortar in super-structureaboveplinth levelup to floor two level ( up to two storeys ) including necessarycutting and mouldingofbrickworkas required andalsoincludinghoney combed brick work in thickness of wall more than 11.5cms. |
| 164 | Dismantiling Existing plaster including disposal of refuse as directed by the Engineer-in charge with in a distance of 60metre (200ft) outer side. |
| 165 | 12 mm cement plasterinsingle coat on rough sideofsingle orhalfbrick wall for interior plastering up to floor twolevelincludinginternalrounded angles not exceeding80mm ingirth and finshed even and smooth. |
| 166 | (1)1 cement : 6Coarse sand |
| 167 | Finishing walls with water proof cement paint of approved make and quality on new work with coats to give an even shade including supply of all materials labour and T & P etc required for proper completion of the work. |
| 168 | Gate |
| 169 | Finishing walls with water proof cement paint of approved make and quality on new work with coats to give an even shade including supply of all materials labour and T & P etc required for proper completion of the work. |
| 170 | Painting Ist coat over priming coat (but excluding cost of priming coat) on steel andothermetalsurfacesup to 10 cm. widthorgirthorsmall articles not exceeding 0.10sqm in area white superior synthetic enamel such as LUXOL3,Hi-gloss apcolitesuperlac,DULUX specifiedbrushingtogiveanevenshadeand including cleaningthe surfaceofall dirt,dust and other foreignmatter sand paperingand stopingincluding cost of all materials, labour toolsandplants etc. required forpropercompletion of the work. |
| 171 | Submersible Pump |
| 172 | Boring/drilling bore well of required dia for casing/ strainer pipe by suitable method prescribed in IS 2800 (Part- I) including collecting samples from different strata preparing and submitting strata chart/ bore log including hire running charges of all equipments tools plants and machinarys required for the job all complete as per direction engineer-in-charge up to 90 m depth bellow ground level all type of soil. |
| 173 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 100 mm nominal size dia |
| 174 | Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 100 mm nominal size dia |
| 175 | Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -incharge. |
| 176 | Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. |
| 177 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 100 mm dia |
| 178 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 32 mm dia nominal bore |
| 179 | Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 100 mm clamp |
| 180 | Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 100 mm clamp |
| 181 | S/F 2 H.P. Submersible Pump with control pannel,cable, columnpipe and all accessories complete. |
| 182 | S/F of finolex of copper cable ISI marked submersible cable size 4sqm 4core. |
| 183 | GST Extra as per applicable |
AI Tender Summary
Tender Timeline
Mar 25, 2023
11:30 IST
Tender Published
Tender notice published.
Completed
Mar 27, 2023
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
CompletedMar 27, 2023
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedMar 27, 2023
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender