|
| 1 | Dismantling all type of plain cementconcrete works, stacking serviceable materrials at site and removing rubbish as directed with in a lead of 75 m In ground floor including roof. |
| 2 | (a) upto 150 mm. thick. |
| 3 | Earth work in excavation of foundation trenches or drains in all sorts of soil (including mixed soil but excluding laterite or sand stone) including removing, spreading or stacking the spoils within a lead of 75m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. . |
| 4 | (a) Depth of excavation not exceeding 1.500 mm. |
| 5 | Earth work in filling in foundation trenches or plinth with good earthin layers not exceeding 150 mm. including watering and ramming etc.layerby layer complete .(payment to be made on the basis of measurement of finished quantity of work). |
| 6 | (a) With earth obtained from excavationof foundation. |
| 7 | Earth work in filling in foundation trenches or plinth with good earthin layers not exceeding 150 mm. including watering and ramming etc.layerby layer complete .(payment to be made on the basis of measurement of finished quantity of work). |
| 8 | ( c)(i) With carried earth arranged by the contracor with in a radius of 1 km. including cost of carried earth. |
| 9 | Laying 150 mm. to 200 mm. boulder soling including rough dressing hand packing and ramming down small pieces in the interstics without rolling but including ramming. |
| 10 | Cost of stone boulder 150 mm size delivered ans stacked at site. |
| 11 | (II) Cement concrete with 30 mm. down graded shingles excluding shuttering.N.B. VarietyIn ground floor . |
| 12 | (a) 1:3:6 proportion. |
| 13 | Ordinary cement concrete (mix 1:1.5:3) with graded stone chips (20mm nominal size) excluding shuttering and reinforcement, if any, in ground floor as per relevant codes. |
| 14 | (ii) River bazree. |
| 15 | Hire and labour charge for shuttering with centreing and necessary staging up to 4 m. using approved stout props and thick hard wood planks of approved thick ness with required bracing for concrete slabs, beams, columns, lintels curved or staight including fitting fixing and striking out after complection of works. (up to roof of ground floor). |
| 16 | (f) 25mm. To 30mm. Shuttering with out staging in foundation etc. |
| 17 | 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor. |
| 18 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc.initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at inter-section, complete as per drawing and direction. |
| 19 | (a) For works in foundation, basement and up to roof of ground floor/up to 4m. Tor steel/Mild steel. |
| 20 | SAIL/ TATA/RINL |
| 21 | Plaster ( to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering conrners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (ground floor). [Excluding cost of chipping over concrete surface]. |
| 22 | (ii) With 1:4 cement mortar . |
| 23 | (b) 15 mm. thick plaster. |
| 24 | Neat cement punning about 1.5mm thick in wall, dado, windowsill, floor etc.NOTE:Cement 0.152 cu.m per100 sq.m. |
| 25 | M.S. gate of jail type as per approved design made of strong M.S. frame work, intermediate stiffeners and round/square bars or angles. M.S. sheet (not less than 14 gauge). Gussets. Cleats etc. including necessary riveting . Bolting. Welding,locking and hanging arrangements fitting and fixing complete as per direction of the Engineer-in-charge.In ground floor.. |
| 26 | Applying decorative cement based paint of approved quality after preparing the surface including scraping the same throughly (plastered or concrete surface) as per manufacturer\"s specification. In ground floor. |
| 27 | (ii) One coat on new surface. |
| 28 | (a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 29 | (A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sandparpering etc. in cluding using of approved putty etc. on the surface , if necessary. |
| 30 | (a) On timber or plastered surface:. |
| 31 | (2)With other than hi gloss of approved quality. |
| 32 | (ii) Two coats( white in shade ). |
| 33 | Supply of PVC pipes & fittings of Schedule 80 (medium duty) conforming to ASTMD-1785 and threaded to match with G.I. Pipes as per IS:1239 (Part-I). |
| 34 | P.V.C Pipes. |
| 35 | 100 mm. |
| 36 | Supplying, fitting and fixing bib cock or stop cock. |
| 37 | Chromium plated Bib Cock short body (Equivelent to Code No.511 & Model- Tropical /sumthing special of ESSCO or Similar brand). |
| 38 | Supply of PVC pipes & fittings of Schedule 80 (medium duty) conforming to ASTMD-1785 and threaded to match with G.I. Pipes as per IS:1239 (Part-I). |
| 39 | P.V.C Pipes. |
| 40 | 20 mm. |
| 41 | Construction of Septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar (4:1) including two 560 mm dia. R.C.C. manhloe cover of approved make supplied, fitted and fixied in the top slab with necessary fittings, 19 mm thick cement plaster(4:1) with neat cement finish to the internal surfaces and 12 mm thick plaster(4:1) to outside wall upto 200 mm below G.L. floor finished with 25 mm thick grey artificial stone including supplying, fitting and fixing all necessary specials, fittings, S.W. tees, C.I. foot rest etc. including excavating earth in all sorts of soil, shoring, bailing and pumping out water as necessary, ramming, dressing the bed and refilling the sides of the tank with earth, removing spoils, fliing up the chamber with clear water, removing foreign materialsfrom the chamber and including constructing attached inspection pit as per approved dawing and connecting all necessary pipes, joints etc. with internal plaster work and artif |
| 42 | For 30 users. |
| 43 | With Bazree (N.B.Variety).(SAIL/TATA/RINL) |
| 44 | Constructing Inspection pit of inside measurement 600mm X 600mm X upto 600mm(depth) with 250 mm thick 1st. class brick work in cement mortar(4:1) on all sides, bottom of the pit consisting of 100 mm thick cement concrete(1:6:3) with stone chips over a layer of jhama brick flat soiling, 15 mm thick (1:4) cement plaster to inside walls and outside walls upto G.L. and 20 mm thick(1:4) plaster to bottom of the pit, providing necessary invert with cement concrete(1:3:6) with stone chips as per direction, neat cement finishing to entire internal surfaces, top of the pit covered with 100mm thick R.C.C. slab (1:1.5:3) with stone chips and necessary reinforcements upto 1% andshuttering including 6 mm thick cement plaster(1:4) in all external surfaces of the slab and one 560 mm dia. R.C.C. manhole cover of approved make supplied, fitted and fixed in the slab with necessary fittings, necessary earthwork in excavation in all sorts of soil, filling sides of the pit with earth and removing spoils |
| 45 | With Bazree (N.B.Variety).(SAIL/TATA/RINL) |
| 46 | Supplying, Fitting & Fixing Factory made P.V.C. door frame of size 50 mmx47mm with a wall thickness of 5 mm, made out of extruded 5 mm, PVC sheet mitercut at two corners and joined with two nos of 1.5 mm long brackets of 15 mm x15mm M.S. square tube. The two vertical door profiles are to be reinforced with 19mmx 19 mm M.S. Square tube of 19 gauge, weather seal to be provided throughout the frame. The door frame shall be fixed with the wall using 65/100 mm longM.S. Screws through the frame by using P.V.C fasteners. A minimum of 4 Nos ofscrews to be provided for each vertical member and minimum 2 Nos forhorizontal member etc. complete as per Manufacturer?s specification anddirection of Engineer-in-Charge. |
| 47 | Providing & fixing factory made 30 mm thick factory made solid pvc door shuttermade out of single piece extruded solid pvc profile . The style & rails shall be ofsize of 75 x 30 mm having wall thickness of 5 mm. The style and top bottom railshall have one side a thickness of 15 mm integrally extruded on the hinge side ofthe profile for better screw holding power. 15 mm thickness shall be of singlepiece extruded solid pvc profile whereas it shall be not be made of sheet pastedprofile) . The styles and rails shall be reinforced with MS tube of size 18 mm(±)1mm x 18 mm (±) 1mm x 1mm painted with primer all four corners ofreinforcement to be welded or sealed . solid pvc extruded bidding (push fit type)will be set inside the styles and rails with a cavity to receive single piece extruded5 mm pvc sheet as panel. The styles and rails will be metered cut and join with thehelp of pvc solvent cement, self tapping screw and braket of size 200 x 75 mm /welded at each corner. Single piece extruded |
| 48 | b) Factory made Single piece extruded PVC profiles door shutter of both sidelaminated wood grains decorative Finish: |
| 49 | Supplying, fitting, fixing marble slab/tiles of 15mm. to 18mm. thic knessin floor, lobby, stair, landing & treads etc. over 20 mm (av.) thick base of cement mortar (1:2) laid with white cement slurry @4.4 kg/sq.m before placing marble & jointed with white cement slurry @ 2.0 kg/sq.m with necessary pigments including grinding and Granite polishing as per direction ofEngineer-in-charge in Ground Floor. {White cement and Pigment to be supplied by the Agency} . |
| 50 | (a) WithMakrana plain pink /Adranga pink / Garbh Gulabi/Udaypur pink / Udaypur Green / Black Bhaslana. |
| 51 | (ii) Area of each Slab/tile exceeding 0.3sq.m. but not exceeding 0.6 sq.m. |
| 52 | Supplying,Fitting & fixing 1st quality Ceramic tiles inwalls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. |
| 53 | (A) Floor With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20 Kg/Sq.m. |
| 54 | (a) Area of each tile up to 0.09Sq.m. |
| 55 | (ii) Other than Coloured decorative including white. |
| 56 | Anodise aluminium barred/tower/socket bolt (full covered) of approved manufactured from extruded section conforming to I.S.204/74 fitted and Fixed with cadmium plated screws:. |
| 57 | (ix) 300 mm long x 10 mm dia. bolt. |
| 58 | Rendering the Surface of walls and ceiling with White Cement baseWATER PROOF wall putty of approved make & brand.(1.5 mm thick) |
| 59 | (b) Priming one coat on timber or plasteredsurface with syntheticenamel oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 60 | Acrylic Distemper to interior wall, ceiling with a coat of solvent basedinterior grade acrylic primer (as per manufacturer\"s specification)including cleaning and smoothning of surface.Two Coats |
| 61 | Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992 . |
| 62 | Single socketed3 meter length. |
| 63 | 110 mm. |
| 64 | Supplying, fitting and fixing PVC pipes of approved make ofof Schedule 80 (medium duty) conforming to ASTMD-1785 and threaded to match with GI Pi;es as per IS:1239 (Part-I) with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting piles, making threads, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required, jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accessories, specials. Payment for painting will be made seperately). |
| 65 | For Exposed Work PVC Pipes. |
| 66 | 25 mm. |
| 67 | Supplying, fitting and fixing PVC pipes of approved make ofof Schedule 80 (medium duty) conforming to ASTMD-1785 and threaded to match with GI Pi;es as per IS:1239 (Part-I) with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting piles, making threads, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required, jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accessories, specials. Payment for painting will be made seperately). |
| 68 | For Exposed Work PVC Pipes. |
| 69 | 15 mm dia. |
| 70 | Supplying, fitting and fixing Peet\"s valve fullway gunmetal standard pattern best quality of approved brand bearing I.S.I marking with fittings(tested to 21 kg per sq.cm.). (Note: Item (vii),(viii) and (ix) to be done as per specific direction of the Engineer-in-charge). |
| 71 | 25 mm. |
| 72 | Supplying PVC water storage tank of approved quality with closed top weith lid (Black) - Multilayer. |
| 73 | 1000 litre capacity. |
| 74 | Wash basin white vitreous china of approved make(without fittings) supplied, fitted and fixed in position on 75mm X 75mm X 75mmwood blocks and C.I. Brackets including two coats of painting of C.I. Brackets. |
| 75 | 450 mm x 300 mm size. |
| 76 | Supplying, fitting and fixing Flat back urinal (half stall urinals) in white vitreous chinaware of approved makein position with brass screws on 75 mm X 75 mm X 75 mm wooden blocks complete. |
| 77 | Corner urinal 440 mm X 345 mm X 250 mm. |
| 78 | Supplying, fitting and fixing Anglo-Indian W.C. in white glazed vitreous china ware of approved makecomplete in position with necessary bolts, nuts etc. |
| 79 | With \"P\" trap (with vent). |
| 80 | Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved makein position complete excluding \"P\" or \"S\" trap (excluding cost of concrete for fixing). |
| 81 | 530 mm X 410 mm. |
| 82 | Ordinary cement concrete(mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttring and reinforcement, if any, in ground floor as per relevant IS codes. |
| 83 | (b) River bazree. |
| 84 | Supplying & laying as per IRC-SP:063-2004 paver unit of anyshade of approved quality as per relevant IS code, laid inpattern as directed in pavement, footpath, driveway (paverblock only), etc including necessary underlay complete in allrespect with all labour and material.[Border concrete if necessary to be paid separately].Note: Sub-grade CBR should not be less than 5. |
| 85 | a) 25 mm thick Tiles as per IS: 1237-2012 forfootpath,ramp,staircase of public building(over 25 mm thick(Avg) Cement mortar (1:3) & Cement Slurry @ 4.4 kg/Sq.m atback side of Block. Cement for Mortar & Slurry to be suppliedby Department |
| 86 | (ii) Coloured Decorative |
| 87 | 18% GST |
| 88 | 1% Labour CESS |
