Tender For Continuation Of Chathan Master Memmorial Hall 201/21 And Providing Related Facilities.-General Electrical Work-Providing Lift
Tender Value
13.93 Lakhs
Estimated cost
Bid Submission
25 Mar 2023
0 days left
EMD
34845
Bank guarantee accepted
Document Fee
2760
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
irinjalakuda → Kerala
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Continuation Of Chathan Master Memmorial Hall 201 / 21 And Providing Related Facilities.-General Electrical Work-Providing Lift
BOQ
| Sl. No. | Item Description |
| 1 | SIT%C of 8 passenge lift |
| 2 | OD219178/2022-2023: Supply ,installation ,Testing and Commissioning of8passenger (544kg) GEARLESS MACHINE ROOMLESS2. Qnty: 1 ( One)3.Load & speed:about 540Kg@1M/sec 4.Control:Microprocessor based V.V.V.F.ARD system5. Power supply: 415volts, 3phase 50cycles, alternating current. 6. Travel:Ground to 1stFloorabout 3.9 mtr 2.Stops & openings: 2 Stops2 openings (all openings on the same side) 8.Machine :DIRECTLY PLACED ABOVE HOIST WAY 9. Operation : Collective Selective With ON/OFF switch 10. Hoist way required : About 1750 MM Wide x1900 MM Deep finished dimension 11.Available: 1800MMWx1900MMW D 12. car size: As per our GA(general arrangement )13. Car enclosure: SS cabin with BRAILLE BUTTON, LCD DISPLAY, FLOOR ANNOUNCEMENT, SS ANTI SKID FLOORING 14.car entrance: Protected by CENTER OPENINGHAIR LINE finishwith infra red curtain,clear opening about 800MM wide15. Hoist way entrances: . protected by CENTRE OPENING SS HAIR LINE .CLEAR OPENING ABOUT 800mm WIDE16.Door Operation: Power OperatedAutomatic 17.Brake : Electromagnetic type which opens on energization with 24/48 VDC voltage and closes by means of spring tension on Deenargisation. The inner surface of the brake will be provided with brake liners. .18.Driving Motor: PMSM(PERMANENT MAGNET SYNCHRONOUS MOTOR 19.Electrical safety device: a. Mains 3phase limit switch to protect against over travel, b. Single phasing preventor with a protection against phase sequence reversal, c. full proof gate locks for landing doors, c. car gate switch, e. overspeed governor, f. over speed safety device Signals :IN CAR : Battery operated Emergency Light, Alarm, Digital floor Indication, Push Button for each floor, On/Off switch Fan switch, At Landing : UP/ Down Indication, Push Button, Digital car position indication . 20.Electric supplySuitable foroperating in 415 V 50 HzAC supply. 21Electric supply ( Light )230V, 50Hz , Single Phase 2 Wire system. 22.Winding handle Manual winding handle for car in case of an emergency. 24.Safety Related . Door Force Detector . Door Nudging Feature . Door Sensor Self- Diagnosis . Electronic Doorman . Extended Door-Open Button for Goods Lift . Fire Emergency Return . Fire Operation . High Accuracy Landing Feature . Slot less Bottom Sills . Inter-Communication System . Elevator Monitoring And Control System . Automatic Rescue Device In Case Of Power Failure (ARD) . Emergency Rescue Device Operated From Cabin (ERD) . Multi-Beam Door Sensor . Overload Holding Stop . Braille On all COP & LOP types . CCTV Facility to Integrate with BMS . Jammed Landing Operation Panel Call Button Bypass . Motor Overheat Protection . Phase Failure & Phase Reversal Protection . 25.Leveling Automatic leveling at all landings 26.Control panel :Control panel will be dust and vermin proof of sheet metal enclosure 27.Tests :At site test as per IS 4666/88 to be carried out before Handing over.28.Door opening system :Infrared door opening system to the system to be provided for the entire length and shall sense & operate even for the instruction of a finger. 29.ARD Automatic rescue device with an electronics controller and with necessary maintenance free batteries .The rescue operation shall act with in 10 secondsof power failure.30Scope of work1) Supply of lift materials 2) Minor civil work suchas construction of buffer block in the pit machine foundation in the machine room, cutting pockets and grounding brackets for the guide rails, grouting boxes for control units in the front side of the wall.3) Scaffolding 4) Door frame5)supporting steel including I chanel accrose the room for lifting/hanging the machineetc 6)Obtaining scheme approval as well as energization certificate from the electrical Inspectorate including preparation of necessary drawing of the same.Necessary fee shall be remitted to the Inspection by the firm for which no refund will be made from the department.7) Supply of book let with complete details of maintenance schedule and control diagram 8)Giving training to department staff for attending trouble shooting. 9)Free servicing for 36 month after handing over.31 Guarantee Company shallcarry out free maintenance during warranty period which shall include. a) Cleaning lift equipment b) Lubrication of all parts c)Replacing of lubricating oil when required d) Checking and adjusting contracts e) Replacing fusible item alarm etcf) Recharging/replacing batteries in case of such requirements g)Replacing/Rewinding motor if required.h) Replacing / rewindingalldefective parts of the lift including V3F Unit if found necessary .DRIVING ROPES : "USHA MARTIN" / "ORIENT" / IMPORTEDCAR VENTILATION : With automatic ON/OFF FanCAR LIGHTING : LED lighting.LEVELING ACCURACY : Max. as per article 10 of IS: 14665 :2000, Min. +_1mmDRIVE : 'FUJI OR EQUIVALENT'STAINLESS STEEL SHEETS : 'SAIL / JINDAL / IMPORTED'MILD STEEL SHEETS : 'TATA/ESSAR/IMPORTED' (MAKE OF LIFT-MITSUBISHI/OTIS/KONE/JOHNSON) |
AI Tender Summary
Tender Timeline
Mar 17, 2023
11:30 IST
Tender Published
Tender notice published.
CompletedMar 25, 2023
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedMar 27, 2023
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender