Tender For Providing Irrigationfacility In Sheep Fram At Deotin Tehsil & Distt. Hamirpur. (H.P.) (Sh:- Laying Jointing And Testing Ofgms Pipe 50 Mm Dia Medium Class For Rising Main & Supply & Erectionofcentrifugal Pumping Machinery Alongwith Allied Access
Tender Value
8.82 Lakhs
Estimated cost
Bid Submission
27 Mar 2023
0 days left
EMD
17656
Bank guarantee accepted
Document Fee
250
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
bhota → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Providing irrigation facility in Sheep Fram at Deotin Tehsil & Distt. Hamirpur. (H.P.) (SH:- Laying jointing and testing ofGMS Pipe 50 mm dia Medium class for rising main & Supply & erection of Centrifugal pumping machinery alongwith allied accessories )
BOQ
| Sl. No. | Item Description |
| 1 | Excavation in foundation , trenches etc.( in pipes & pits), in all kinds of soil suchas pickwork, jumper work blasting work, insoft / hard rock, including chiseling wedging out of rocks clearance of bushes etc.including shoring, dewatering etc. in all leads and lifts stacking the excavatedsoilupto any lead and liftclear from the edge of excavation and then returning the stacked soil in 15cm layers when required into plinth , sides of foundation etc. consolidating each deposited layers by ramming and watering and then disposing of all surplus earth complete within all leads and liftsas per direction and to the entire satisfaction of the Engineer-in-Charge. |
| 2 | Laying,jointing and testing of in trenches ( to level or grade) of GMS pipes Medium Clas ( bevelled edge butt welded pipe 50mmdia conforming to IS 1239-2004( Latestwith upto date ammendments) as specified , suitable to withstand required hydraulic test pressure including fixing of required number of bends of all degree,teecomplete in all respects . The laying of pipes shall conform to IS 5822-1994 as well as CPHEEO manual and will include all operations such as jointing including flushing , cleaning and hydraulic testing complete in all respectswith in all leads and lifts as per the direction and to the entire satisfaction of the Engineer-in-Charge |
| 3 | Providing and fixingdouble flanged cast steelsluice valve of 50 mm dia class ASA -150 having test pressure of 21 kg Cm2 of Leader/ Kirloskar /Kartarmake as per BIS 1414- API-600 complete in all leads and lifts complete in all respects inclcuding required No.of Nuts and bolts and gasket sheet not less than 4mm in thickness to the entire satisfaction of the Engineer-in-Charge .. |
| 4 | Providing horizontal spindle horizontal split casing/end suctions (back pull out arrangement) single/doublemultistagecentrifugal pumpof recommended make such as Mather and Platt/ KSB/ Kirloskaras per BIS-1520-1980 with up to date amendments, read with IS: 9137-1978or latest editionsuitable for lifting clear water for under mentioned characteristics with Bronzeimpellers/priming funnels, casing ring andshaft sleeves of bronze,shaft of steel grade EN-8 with cast iron casing coupled directly through a flexible coupling on aMS/Cast steel base plate( baseplate to be from the manufacturers of the pumping unit only) toSqurrel cage induction motor of standard make such as Kirloskar/Crompton/ NGEFand suitable for operation on 400 (+)/-) 10% volts, 50 cycles/second, 3 phase AC electricsupply. The power of electric motor should be at least 10% in excess of the maximum power required by the pump in the operation range of (+) 10% and (-) 15%of the duty point head. The motor shouldbeas perIS: 325-1978 with up to date amendmentsread with IS: 900-1972. It shold include the cost of bearingnuts, bolts and painting etc and should meet the followingrequirement. |
| 5 | Discharge (Q) 3.33 LPS or 11.988 Cum/Hour for each pump. |
| 6 | Total head in Mts.184.00 meters |
| 7 | (a) LWL in sump well (h) 808.00 mtrs. |
| 8 | (b) Shaft level 811.00 mtrs. |
| 9 | (c ) Level at discharge point |
| 10 | (d) Suction lift0.00mtrs. |
| 11 | (e) Residual head 3 mtrs. |
| 12 | (f) Static head 134.00 mtrs. |
| 13 | Rising main |
| 14 | (a) Length650 mtrs. |
| 15 | (b) dia50 mm |
| 16 | Pumping hours 8hours |
| 17 | Altitude of installation above MSL808.00mtrs. |
| 18 | Characterstics of water |
| 19 | (a) Temperature 20 degree centigrade |
| 20 | (b) Abient Temp. |
| 21 | ( c) Turbidityupto50.00 NTU |
| 22 | (d) AlkalanityMg/Ca Co3 |
| 23 | (e) Size of the solids |
| 24 | (f) Other |
| 25 | Supplyingand fixing of prefabricated control panel consisting of VAF meter, Amp. meter, voltmeter, OCB/MCB/MCCB, ON/OFF push button, circuit breaker, Voltage monitor relay, voltmeter, power factor meter, frequency meter, Bus bar chamber,ICTP main switch with HRC fuses,Ammeter, capacitor, immersed strarter delta /direct one line/auto transformer,preventor, hour run meter as per technical specification sheet attached complete in all respect & to the entire satisfacction of the Engineer-in-Charge. |
| 26 | Supply of Kirloskar/Leader make dia. caststeel Class ASA-150 double flanged sluice valve havingone diaHigher than pump size to delivery of pumpand capable of with standing nominal seat pressure of 21.00 kg/cm2 as perBIS1414-API -600 as per technical specification sheet attached complete in all respect & to the entire satisfacction of the Engineer-in-Charge. |
| 27 | Providing and fixingdouble flanged cast steelnon returnvalve having dia one dia higher than delivery of pumpclass ASA -150 having test pressure of 21 kg Cm2 of Leader/ Kirloskarmake as per BIS 1868- API-600 complete in all leads and lifts complete in all respects inclcuding required No.of Nuts and bolts and gasket sheet not less than 4mm in thickness to the entire satisfaction of the Engineer-in-Charge . |
| 28 | Supply of Kirloskar/Leadermake dia. cast steel double flanged(swing check type ) refelux valve having bye pass arrangement and size equal to dia of rising main i.e. 50 mmcapable of with standing nominal seat pressure of 1 class ASA -150 having test pressure of 21 kg Cm2 complete in all respect & to the entire satisfacction of the Engineer-in-Charge. |
| 29 | Providing and fixing GI piping work (Layout to be approved by the Engineer in charge) for suction and delivery pipes suitable to pump(s) offered and common header as per the R/Main respectively complete with all specials such as bends, tees, reducers. Increasers with companions flanges matching with the relevant specifications of the accessoriesincluding rubber/asbestos gasket of minimum 3mm thckness as per IS:2712:1979 and required number of nuts and bolts as per IS:1364:1983, The Pipes fittings and joints shall be as per relevant IS code & to withstand 1.5 times total head. The size of the various components incorporated in the technical specification sheet complete in all respect. |
| 30 | a) Suctionside= 50mm dia |
| 31 | a) Deliveryside= to be specified by the tender. |
| 32 | a) Common header= 50 mm dia |
| 33 | Providing and laying copper PVC insulated armoured power cable (One cable carrying all the three phases) of suitable size andcapacity to motors and all other electircal equipments as per IS:1554(P-I) 1988 or latest with upto date ammendments of siemens/GLOSTER /IEC/ICC/EICO/NATIONAL/GRANDLAY make including all other accessories such as thinbles, flexible pipes,solders,nuts and bolts cable glands etc. laid in pipes or trenches under floor :- |
| 34 | a)Supply side(From Meter of HPSEB to bus bar and switch) = |
| 35 | b) Motor side (From switch to starter and starter to motor) = |
| 36 | Providing andlaying double loop earthing with GI plate 600x600x3mm thick electrode complete with materialsuch as charcoal, common salt ,GI pipes,thimbles,nuts & bolts,digging of pits,GI wiring & 25x5mm GI strips of required capacity conforming to BIS 3043-1987 latest with up to date ammendments for above motors & other electrical equipment. |
| 37 | Supply of standard make 100mm dia circular dial pressure gauge of suitable range Fiebeg/Bourden/ Precision make with all accessories such as stop cock,copper tubing etc. conforming to BIS 3624-1987 or latest with up to date amendments. |
| 38 | Eraction of Pumping machinery along with allide accessories from Item no. 4 To 12complete in all respects. |
AI Tender Summary
Tender Timeline
Mar 16, 2023
11:30 IST
Tender Published
Tender notice published.
CompletedMar 27, 2023
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedMar 27, 2023
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender