|
| 1 | Adjustable pipe die set BSP | cover pipe size 1or 3/4 |
| 2 | Micrometer inside with extension rods. | Accuracy 0.01 mm withextension rods up to 150 mm |
| 3 | Micrometer outside. | 50 - 75 mm |
| 4 | Pipe vice | 100 mm |
| 5 | Pipe wrench | 400 mm |
| 6 | Taps and dies complete set in box. | Whitworth |
| 7 | File card. | 3x5 inch size, brass or steel wire |
| 8 | File flat bastard | 200 mm |
| 9 | Screw pitch gauge Metric | 0.25 to 6 mm |
| 10 | Universal scribing block. | 220 mm |
| 11 | Adjustable spanner. | 380 mm long |
| 12 | Digital Micrometer outside. | 0 - 25 mm L.C. 0.001 mm. |
| 13 | File half round second cut. | 250 mm |
| 14 | Hollow punch | Straight Shank Hollow Punch Sets 5-12mm |
| 15 | Vernier Bevel protector | Range 360deg, LC.5min150mm blade |
| 16 | Bearing different types | each type of diameter 25mm min. |
| 17 | Bearing extractor | Universal gear puller 2 or 3 jaws adjustable |
| 18 | Double Ended tubular Box spanner set with Tommy bar. | A/F 6-25 mm set of 10Tommy Bar Dia. 6, 8, 10, 12,14, 16 |
| 19 | Dowel pin straight | Dia. -1 inch Length -4MatStainless Steel |
| 20 | Drill twist Taper shank | 8 mm to 20 mm by 0.5 mmH.S.S. |
| 21 | Engineers try square knife-edge | 150 mm Blade |
| 22 | File triangular smooth | 200 mm |
| 23 | Gauge snap Go and Not Go | 25 to 50 mm by 5 mm, Set of6 pieces |
| 24 | Interchangeable ratchet socket set | 12 mm driver, sized10-32 mm set of 18 socket and attachments. |
| 25 | Knurling tool Diamond, straight and Diagonal | Standard |
| 26 | Packing gasket | PTFE gasket roll small size |
| 27 | Pulley extractor | Universal gear puller 2 or 3 jaws adjustable |
| 28 | Slip Gauge as Johnson metric set. | 87 Pieces Set |
| 29 | Spanner adjustable | 150 mm |
| 30 | Standard Tap screws | M3, M4, M5, M6, M8, M10, M12, M14, M16 |
| 31 | Straight edge steel | 300 mm or above |
| 32 | Temperature gauge | Range 0 - 150°C |
| 33 | V-belt and Flat belt | to fit on pulley |
| 34 | V-Block pair with clamps | 150 x 100 x 100 mm |
| 35 | Wheel dresser One for 4 units Star-Dresser with Holder | Length 150 mm, diamond point |
| 36 | Arm strong type tool bit holder. | Straight |
| 37 | Drill Drift May be manufactured in- house | 200mm hardened and black finish |
| 38 | File round bastard. | 250 mm |
| 39 | File square second cut | 250 mm |
| 40 | Blow Lamp | 0.5 litre |
| 41 | Caps screws | M6, M8, M10, M12 |
| 42 | Drill twist straight shank | 3 mm to 12 mm by 0.5 mmH.S.S. |
| 43 | Stud Extractor EZY - out | Set of 8 |
| 44 | Arm strong type tool bit holder. | Left hand |
| 45 | ClampC | 200 mm |
| 46 | Damaged old spur gear | to fit 50mm dia. Shaft |
| 47 | File feather edge smooth | 150 mm |
| 48 | File Swiss type needle | Set of 12, Length150 mm |
| 49 | Lifting sling | 8mm Nominal Dia. Single leg sling |
| 50 | Oil Can | 250 ml |
| 51 | Steel keys May be manufactured in- house | to fit with key slot of shaft and pulley |
| 52 | Stop cock | 25NB 2-way, Threaded end |
| 53 | Washer, clutch, keys, jib, cotter andcirclip | minimum 25mm size, carbon steel material |
| 54 | File half round bastard. | 250 mm |
| 55 | Vernier caliper | 150 mm |
| 56 | File flat bastard. | 300 mm |
| 57 | Slip-on Forged steel Flange | 150NB, ANSI-B16.5,Class 150 |
| 58 | File hand second cut. | 150 mm |
| 59 | File flat second cut safe edge. | 300 mm |
| 60 | Chisel cold crosscutand diamond point. | 9 mm X 150 mm |
| 61 | Scraper flat | 150 mm |
| 62 | Scraper half round | 150 mm |
| 63 | Scraper triangular | 150 mm |
| 64 | Chisel cold round nose | 9 mm X 100 mm |
| 65 | Caliper inside spring type. | 150 mm |
| 66 | File flat - second cut | 250 mm |
| 67 | Hacksaw frame fixed type | 300 mm |
| 68 | Scriber | 150 mm |
| 69 | Steel Rule with metric and British graduation | 150 mm, Stainless steel |