|
| 1 | Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 2 | Extra for scrapping, cleaning and straightening reinforcement from R.C.C. or R.B. work |
| 3 | Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead :Thickness above 25 mm upto 40 mm |
| 4 | Disposal of building rubbish/ malba/ similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground (upto 20 km ) or as approved by Engineer-in-charge, beyond 100 m initial lead, for all leads including all lifts involved. |
| 5 | Brick work with common burnt clay F.P.S.(non-modualar) bricks of class designation 75 in foundation and plinth in Cement mortar 1 :4 ( 1 cement : 4 fine sand), Extra for brick work in superstructure above plinth levelupto floor V level. (By manual means) |
| 6 | 12mm Cement plaster of mix: 1 : 4 ( 1 cement : 4 coarse sand) |
| 7 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 8 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade,New work (two or more coats) over and including priming coat with cement primer |
| 9 | Applying priming coat with ready mixed red oxide Zinc Chromate primer of approved brand and manufacture on steel galvanised iron/steel works |
| 10 | Painting with ready mixed synthetic enamel paint of approved brand and manufacture in all shades to give an even shade Old steel work (one or more coats) |
| 11 | 15mm Cement plaster on the rough side of single or half brick wall of mix:1 : 4 ( 1 cement : 4 fine sand) |
| 12 | Extra for washed grit plaster on exterior walls of height more than 1Om ground level for every additional height of 3m or part thereof |
| 13 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.75 mm diameter |
| 14 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. |
| 15 | Coupler 75 MM |
| 16 | Single pushfit Coupler 75mm |
| 17 | Single tee without door 75mm |
| 18 | Shoe (Plain) 75mm |
| 19 | Providing and laying machine cut, mirror polished Marble stone flooring, in required design (Simple geometrical, abstract etc.) and in patterns in combination with Italian marble stones of different colours, shades and finished surface texture etc., in linear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc. |
| 20 | Providing and fixing machine cut, mirror/ eggshell polished , Marble stone work for wall lining (veneer work) including dado, skirting, risers ofsteps etc., in required design and pattern wherever required, stones of different finished surface texture, on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all complete as per Architectural drawings, and as directed by the Engineer-in-Charge.18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc. |
| 21 | Providing and laying Flamed Finish Granite stone flooring in required design and patterns, as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :Flamed FinishGranite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivale nt. |
| 22 | Providing and laying Flamed Finish Granite stone flooring in required design and patterns, riser of step /dado /skirting of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :Flamed FinishGranite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 23 | Supply and Installation of DGU Glass Thickness 24mm; 6 mm Thick Clear Toughened + 12 mm Air Gap + 6 mm Thick Clear Toughened including providing and fixing 200 micron thick Blast Mitigation Film (including Shatter Resistance capability) i) Fixed Windows/Glazings |
| 24 | Providing and fixing tiled False Ceiling of approved materials of size 595x595mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanised @ 120 gms/sqm both side inclusive ) consisting of main \"T\" runner with suitably spaced joints to get required length and of size 24x38mm made from 0.30mm thick (minimum) sheet spaced at 1200 mm center to center and cross \"T\" of size 24x25 mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main \"T\" at 600mm cente to centre to form a grid of 1200 x 600mm and secondary cross \"T\" of length 600mm and size 24x25 mm made of 0.30mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 24x24x0.30mm and laying false ceiling tiles of approved texture in the grid including, wherever, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \"T\" runners to be suspended from ceiling using Gl slotted cleats of size 27x37x25x1.6mm fixed to ceiling with 12.5mm dia and 50mm long dash fasteners,4mm Gl adjustable rods with galvanised butterfly level clips of size 85x30x0.8 mm spaced at 1200mm center to center along main T, bottom exposed width of 24mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineerin- charge. (The rate is excluding the cost of tiles which will be paid for separately). 12.5 mm thick fully Perforated Gypsum Board tile madefrom plasterboard having glass fibre conforming to IS:2095 part I , of size 595x595 mm, having perforation of9. 7x9. 7 mm at 19.4 mm c/c with center borders of 48mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC (Noise Reduction Coefficient) of 0.79, •with 50 mm resin bonded glass wool backing. |
| 25 | Providing and laying of quartzite stone pavingsize of (100x100x100 mm ) using cement mortar and grouting of joints with cement sand grout, including providing and laying cement concrete (M15) at the edges of the paving as per drawing. |
| 26 | Providing 12mm thick glass (sliding and openable both type) door in aluminium jumbo section including handle and locking arrengement all complete . |
| 27 | Providing laminated vaneer lumber conforming to IS. 14616 and TAD-15: 2001 (part B) in factory made frames of doors, windows, clerestory windows and other frames wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately). |
| 28 | Factory manufactured flush door fixed in position iron hinges, etc (excluding the cost of any fittings other than specified above but including labour for fixing the same in position (Code : II Revision IS-2191 Part-I) 1973 Decorative with teak facing on both sides edges lipped with teak with laminated core 35 mm thick |
| 29 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts ans sturts, etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement. 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded crushed stone aggregate 20mm nominal size) 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded crushed stone aggregate 20mm nominal size) |
| 30 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelMild steel and Medium Tensile steel bars (10 m and 12 mm dia bars ) |
| 31 | Centering and shuttering including strutting, propping etc. and removal of form for all heights :Suspended floors, roofs, landings, balconiesand access platform. |
| 32 | Providing and fixing in position pre-cast R.C.C. perforated tank door cover and frame of required shape and approved quality (600X450x125 MM ) |
| 33 | Providing & fixing V.C. European Water Closet wall mounted with `P\" trap Hindware,Jaquar, cera or equivalent (as approved by engineer in charge) flushing plate and with approvedslim concealed cistern body with drain pipe connection set for wall hung WC etc. or approved equivalent make including soil connections of 10 Cm pipe upto wall,2.5 Cm. P.V.C. flush pipe etc. complete. All pipe joints under the floor to be filled with epoxy putty. |
| 34 | Providing & fixing Hand Shower (Health Faucet) with 8 mm. dia. tube & wall hook. Hindware or equivalent. |
| 35 | Providing and fixing star white glazed pedestal wash basin,Hindware,Jaquar, cera or equivalent (as approved by engineer in charge)make with 15 mm dia sensor operated C.P. pillarcock of “Crabtree” or approved equivalent make P.V.C. feed pipe, 32 mm C.P., waste coupling, 32 mm C.P. bottle trap as specified & directed. |
| 36 | Providing and fixing “d-line” make or approved equivalent make, wall mounted waste paper bin |
| 37 | Providing and fixing star white glazed sensor operated urinals Hindware,Jaquar, cera or equivalent (as approved by engineer in charge)or approved equivalent make with necessary fittings & as per manufacture’s specifications etc. complete |
| 38 | Providing and fixing star white glazed Division Plate between two urinals Hindware,Jaquar, cera or equivalent (as approved by engineer in charge)make. |
| 39 | Providing and fixing toilet paper holder C.P. brass |
| 40 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with brackets of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. |
| 41 | Providing and fixing hand dryer of approved make and sample as per Architect’sinstructions. |
| 42 | Providing and fixing “Blue Star” make or approved equivalent make water cooler, all as per Architect’s instructions.Capacity = 15 ltr |
| 43 | Providing (d-line) make or approved equivalent make waste paper cup unit, all as per Architect’s instructions. |
| 44 | Providing laying fixing and testing Gl pipe 15 mm diaand special tee bends sockets , elbows etc as per design . inside building and tested etc. complete including cutting and threading (b) including cost of special tee bands socket etc ,all complete |
| 45 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931.15 mm nominal bore. |
| 46 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore. |
| 47 | Providing and fixing mirror of superior glass( of approved quality) and of required shape and size with plastic . moulded frame of approved make and shade with 6 mm thick hard board backing:Rectangular shape 1500x450 mm |
| 48 | Providing and fixing 32mm dia Gl water waste pipeembedded into wallupto All level and heights |
| 49 | providiing andfixing in position best indian made flexible tube connection C.P Brass 15mm x 375 mm |
| 50 | Providing and fixing in position HCI floor trap conforming to lSIspecification of reputed firm of the self cleaning design design with with CP brass hinged grating with frame with or without arm and including cement concrete 1:2:4 under and around the floor trap where required up to floor level complete in all respects including cutting and making the good walls and floor etc. minimum depth of water should be 150mm with minimum seal 50mm b) 75mm internal diameter outlet. |
| 51 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : |
| 52 | 1OOmm i/d (1.36kg)Sand cast iron S&S as per IS: 3989 |
| 53 | 75mm i/d (1.13kg.)Sand cast iron S&S as per IS - 3989 |
| 54 | Painting HCI soil waste, vent pipes and fittings with black bitumastic paint of approved manufacture,lSI marked with 2 Coat on new work with lSI marked paint. |
| 55 | 1OOmm internal diameter |
| 56 | 75mm internal diameter |
| 57 | Providing and fixing in position H.C.L. soil waste vent or antisyphonage pipes to I.S.I. specification of E.D.C. manufactureor of any other reputed firm including cutting a,nd wastage etc. and cutting holes in walls roofs |
| 58 | HCL 1OOmm intarnal diameter |
| 59 | HCI 75mm internal diameter |
| 60 | Providing and fixing square- mouth S.W. gully trap grade \"A\" complete , with C. I. grating brick masonry chamber with bricks of class designation 75 and water tight C. I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2. 70 kg as per standard design.100 x 100 mm size P type With F.P.S. brick |
| 61 | Excavation for pipe line trenches and pits, in open areas where disposal of surplus earth is done along the allignment, including trimming and dressing sides, levelling of beds of trenches to correct grade, cutting loint holes, refilling, consolidation and dewatering of refille in 15 em layers and resoration of unmateled or paved surface to its orignal condition. The rate includes the cost of the accessories timbering, dewatering of rain water diversion for trafic, night signal, fixing causion boards, watching fencing etc. (i) from 6.00 mts depth down to 7.5 m depth in case of all classes of soil except rocky.P/L and jointing glazed stone wire pipes clamp spl with stiff mixture of cement mortar in the proportion of 1:1 (1 cement1 sand ) including testing of band etc. complete |
| 62 | P/L cement concret 1:5:10 ( 1 cement 5 sand 10 coarse graded ) all round S.W. pipes including bed concrete as per standard desigen |
| 63 | 100 mm diameter S.W. pipe (a) Crushed. |
| 64 | 150 mm diameter S.W. pipe (a) Crushed. |
| 65 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) R.C.C. top slab with 1 :2:4 mix ( 1 cemE?nt : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement: 3 coarse sand) finished with floating coat of neat cement and makingchannels in cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finsihed with a floating coat of neat cement complete as per standard design.Inside size 90x80 em and 45 em deep including C.l. cover with frame (light duty) 455x61 Omm. internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kgWith F.P.S. bricks with class designation 75 & with (a) Crushed stone aggregate including C.l cover with frame (light duty ) 455x61Omm internal dimensions total weight of cover and frame to be not less than 38 kg( weight of cover 23kg and weight of frame 15kg) with F.P.S.brick with class designation 75 |
| 66 | Providibg and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour.Waste coupling 38mm of 83mm length and 77mm breadth, weighing not less than 60gms. |
| 67 | Providing and fixing PTMT Bottle Trap for Wash basin and sink.Bottle trap 38mm single piece moulded with height of 270mm, effective length of tail pipe 260mm from the centre of the waste coupling 77mm breadth with 25mm minimum water seal, weighing not less than 263gms. |
| 68 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank lSI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank [Sintex, Electroplast, Star, Lotus or equivalent having valid lSI license]. |
| 69 | Constructing brick masonry road gully chamber 50x45x60 cm with bricks of class designation 40 in cement mortar 1:4 (1 cement : 4 sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame (minimum weight of grating 75 kg) complete as per standard design :With Modular bricks |
| 70 | Providing and laying S&S centrifugally cast (spun) iron pipes (Class LA) conforming to IS - 1536 :100 mm dia pipe including flanged C.I. standard specials such as tees, bends,collars, tapers, caps etc., suitable for flanged jointing as per IS : 1538 :Up to 300 mm dia |
| 71 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. |
| 72 | 150 mm nominal outer dia Pipes |
| 73 | 100 mm nominal outer dia Pipes |
| 74 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe |
| 75 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc. |
| 76 | Providing and fixing buff tectile tile 300x300 mmin cemet mortaras per design including pointing the joints with white cement mortar 1: 2 with admixture of matching tile above pcc sub base . |
| 77 | Providing and fixing one exhaust fan point |
| 78 | 6 AMP. POINTS ON SEPARATE BOARD : Supply,fixing,testingandcommissioningof1No6AMultiSocketwith 1No. 6 A switch ( Modular type ) with cover plate , sheet steel box / PVC modularbox etc on surface/ concealedmannerI/c electricalconnections and making good all the damages, painting, cleaning the site etc complete as required as per site requirement and as directed. |
| 79 | POINTSFor Computers:Supply, fixing, testing and commissioning of following Modular type switch socket with cover plate, PVC modular box on Surface / sheet steel boxinconcealedmannerI/celectricalconnectionsandmakinggoodall the damages,painting,cleaningthe site etc completeas requiredas per site requirement and as directed. a.2 Nos. 6 A Switch + 3 Nos. 6 A, 3 pin Socket |
| 80 | Supplying, providingwiring (supply, fixing, testing and comm.etc)for Light / Power with following PVC insulated copper conductor single core multi strendedwire( HRFR) in existingconduiti/c electricalconnectionsand making good all the damages, painting, cleaning the site etc complete as required as per site requirement and as directed. |
| 81 | 3 X 4.0 sqmm ( For Power Circuit )in 20 mm steel conduit |
| 82 | 6 X 4.0 sqmm ( For Power Circuit )in 25 mm steel conduit |
| 83 | 6 X 2.5 sqmm( For UPS Circuit )in 25 mm steel conduit |
| 84 | 1 X 16 + 1 x 10 + 1 X 4 .0 sqmm ( For UPS DB ) in 25 mm steel conduit |
| 85 | Supplying, Installation, testing and commissioning of the telephone point with the followings - a. Two pair, 0.50 mm dia. telephone cable tinned copper conductor, P.V.C. insulated and sheathed , fire retarding, anti termite, colour coded twisted pairs and rip cord. |
| 86 | Double outlet with shutter modular type Telephone Outlets ( RJ – 11 ) with suitable size M.S./ PVC modular boxes complete as req. |
| 87 | 20 mm dia.1.6 mm wall thickness rigid PVC conduits. |
| 88 | Supplying and fixing of krone telephone tag block, suitable for the multi core telephone cable and shall accommodate tin-plated phosphor bronze connectors, the connectors shall splice unskinned cables up to 0.61 mm dia and shall be terminate both incoming and out going lines, the tag blocks shall be mounted inside, water proof box and locking arrangement and shall be fully accessible.The item is inclusive of providing and fixing of boxes in surface / recessed system etc complete as required. a. 50 pair tag block |
| 89 | LIGHT DISTRIBUTION BOARD :a.1 no. TPN MCB DB 4 way ( 4 + 12 ways )b.1 no TPN MCB 32 amp. c.12 nos SP MCB 06 amp. |
| 90 | U.P.S. DISTRIBUTION BOARD ( for UPS IN PUT ) :a.63 A SPNMCB – 1 no.b.1 No Fabricated 18 swg m.s.box of suitable size OR factory made. |
| 91 | POWER DISTRIBUTION BOARD : ( FOR UPS )a.1 no. TPN MCB DB 4 way ( 4 + 12 ways )b.1 no TPN MCB 63 amp. c.6 nos SPN MCB 63 amp. |
| 92 | VERTICAL DB ( Doubledoor) : ( FOR POWER ) :Supplying and fixing of following 4 Way three pole and neutral, sheet steel Vertical MCB distribution board , 415 volts on surface / recess, complete with tinned copper busbar , neutral bar, earth bar , din bar , detachable gland plate with Cable termination box, interconnection including painting,earthing etc as required,With the followings - a. 01 no. 125 amp., 10 KA , TP MCCB b. 63 A TP MCB - 4 Nos. |
| 93 | VERTICAL DB ( Double door ) : ( FOR LIGHT ) Supplying and fixing of following 4 Way three pole and neutral, sheet steel Vertical MCB distribution board , 415 volts on surface / recess, complete with tinned copper busbar , neutral bar, earth bar , din bar , detachable gland plate with Cable termination box, interconnection including painting,earthing etc as required,With the followings - a. 01 no. 100 amp., 10 KA , TP MCCB b. 32 A TP MCB - 4 Nos. |
| 94 | Supply, Installation, Testing and Commissioning of 24 Port ( 100 base TX ) Cat-6 Patch / jack panel with connectors, outlets and necessary connectivity complete as required. |
| 95 | One Meter length. |
| 96 | Two Meter length. |
| 97 | Supply and laying of Four Pair UTP CAT 6 LAN cables in existingPVC Conduit / Floor trunking with RJ-45 connector if req.as req. |
| 98 | Supply and fixing of modular type Information Outlets with suitable size M.S./ PVC modular boxes complete with insulation displacement connectors etc suitable for CAT 6 UTP Cabling. a. One Port. |
| 99 | Supply, Installation, Testing and Commissioning of the following 10 / 100 Mbps Rack mounted Switch ( Auto managed ) suitable for auto-sense the network speed of the connected nodes to run at either 10 Mbps or 100 Mbps. The port also auto negotiate between full / half duplex and cable cross over. a). 24 RJ-45 10 base –T / 100 Base – TX port. |
| 100 | Supply, Installation, Testing and Commissioning of the following Rack on existing wall / table / plateform etc i/c fixing of equipment/ accessories etc as required. a. 9 U Rack. 2 Nos. |
| 101 | 20 mm dia.1.6 mm wall thickness rigid PVC conduits. |
| 102 | 25 mm dia.1.6 mm wall thickness rigid PVC conduits. |
| 103 | CABLING : Supplying, unloading, storing , laying, testing and commissioning of following sizes of PVC / XLPE insulated (Heavy duty) Al / Cu conductor armouredcablessuitableforworkingvoltageuptoandincluding1100 Volts,laid andtiedonexistingoverheadcabletrays;orlaidandtied overMSsupportsinmasonrytrenchesincludingprovidingMSsupports andclampsforfixingtosupports;orburiedinground completeas required and as per specifications. |
| 104 | 3.5 Core, 35 sq. mm XLPE Al. Cable. ( V DB LIGHT ) |
| 105 | 3.5 Core, 25 sq. mm XLPE Al. Cable. ( V DB POWER + UPS ) |
| 106 | 4.0 Core, 16 sq. mm Al. Cable. ( Power DB ) |
| 107 | 4.0 Core, 10 sq. mm Al. Cable. ( Light DB ) |
| 108 | LED LUMINAIRES :Supply, installation, testing and commissioning of recessed mounted LED light fitting ( 600 x 600 mm ) suitable for grid/gypsum ceiling complete as required, as under a. 36/38 X 1 Watts class LED fitting. Model as under 131 Nos. PHILIPS:- RC 380 B LED- 30-6500 PSE OD WH WIPRO:- CRCO1ORO 38 HP57 HAVELLS:- LHEWEBP7PL2W036 CG:- LCTLR-36-FO-CDL |
| 109 | LED DOWN LIGHTER : Supply, installation, testing and commissioning of recessed mounted circular down lighter complete as required. a. 15 Watts class LED 57 Nos PHILIPS:- GREENLED- DN193B LED-12S-6500 PSU WIPRO:- IRIS LED LD 71-121-XXX-50-XX HAVELLS:- LHEBJNP ZPZ 1W 015(ENDURA LOW DEPTH) CG:- LC DD-15-CDL |
| 110 | BOX TYPE LUMINAIRES: ( T-5 ) Supply, installation, testing and commissioning of Box type Flourescent Tube Light fixture made of CRCA sheet steel channel duly pre-phosphated & powder coated with holder, 1 no 28 watts High efficiency Linear flourescent lamp having 2900 lumens and high frequency replacable digital ballast ( THD < 10% ) all pre wired up to a terminal block / mains connector etc tested as per IEC 598 / IS 10322, complete as required as per approved make. |
| 111 | EXHAUST FAN : Supply, installation, testing and commissioning of the following single phase Exhaust Fan continuously rated, capacitor start and run type, totally enclosed and ruggedly built, pre lubricated double ball bearing, copper wounded, A & E class insulation, dynamically balanced, below 40 db sound level etc. a 300 mm sweep, 900 r.p.m. exhaust fan. |
| 112 | Supply, installation, testing and commissioning of cove lights complete as required |
| 113 | Supply, installation, testing and commissioning of maintenance free chemical earthing of OBO betterman, CCM chemicals and sealed at both ends. Tube shall have double layer electrode, lead conductor welded to tube, with back fill and cast iron cover 300 x 300 mm and complete in all respects. ( The installation procedures should be followed as instructed by the Earth Electrode supplier). |
| 114 | Supplying & drawing the following sizes of copper wire in the existing surface / recess PVC conduit along with PVC earth wire as required 8 No. copper tar |
