}

Supply Installation Testing And Commissioningof Electro-Mechanical Works For Wss Peth Makhama Under Jjm, budgam-Jammu And Kashmir

Public Health Engineering Department-PHED has published Supply Installation Testing And Commissioningof Electro-Mechanical Works For Wss Peth Makhama Under Jjm. Submission Date for this Tender is 01-04-2023. Electromechanical Work Tenders in budgam Jammu And Kashmir. Bidders can get complete Tender details and download the document.




Tender Notice

36517389
Corrigendum : Supply Installation Testing And Commissioningof Electro-Mechanical Works For Wss Peth Makhama Under Jjm
Open Tender
Indian
Jammu And Kashmir
budgam
01-04-2023

Tender Details

Supply installation testing and commissioningOf Electro-Mechanical Works For Wss Peth Makhama Under Jjm

Corrigendum Details

Sr No CorrigendumDate Corrignedum CorrigendumType NewSubmissionDate
1 06-Mar-2023 other Other 20-03-2023
2 09-Mar-2023 DG SET Other 20-03-2023
3 21-Mar-2023 Corrigendum for Extension Date 01-04-2023

Key Value

Document Fees
INR 200 /-
EMD
INR 200.0 /-
Tender Value
INR 45.50 Lakhs /-

BOQ Items

Name of Work:SITC of Electro-Mechanicalworks for Water Supply Scheme PETH MAKHAMA(DISTRICT - BUDGAM) under JJM
Sl. No. Item Description
1Supply, Installation, Testing & Commissioning of Open Well Submersible Pumping Units as per IS 14220 : 1994. PUMP: - Discharge= 8000GPH Head = 65 Mtrs (Rest Technical Specifications as per Annexure "A")
2Fabrication, providing and fitting of split type MS clamps 10 mm thick, Length as per sump opening and 3 inch wide for lowering and holding of pumping unit. The job includes the cost of required size nuts and bolts.
3Providing and fitting of 16 Sq.mm, 3-Core, flat submersible copper cable conforming to IS: 694 (Part 1st) – 1964 & IS: 694 (Part 2nd) - 1964 for Submersible Pumping Unit and other electrical Equipments. The cable connections terminal shall be fitted with copper thimbles of required size. (for pumping units and interconnections)
4Fabrication, Providing and fitting of Modular motor control panel of appropriate size fabricated out of 14 SWG sheet having required openings/vents and protection Class : IP-55 & fitted with accessories (Rest Technical Specifications as per Annexure "A")
5Providing, fitting, testing and commissioning of 50 KVA voltage stabilizer (Rest Technical Specifications as per Annexure "A")
6Providing and Fitting of 3.5-Core, 70 Sq. mm XLPE, and 11KV grade Armoured Aluminum Cable of various sizes conforming to IS: 7098 part 1st as service line from the HT transformer to control panel including necessary thimblings, crimping, taping etc. to be fitted from changeover panel to modular panel. The job also includes P/F of Aluminum thimbles of various sizes as per site requirement including crimping and taping.
7Providing and fitting of 100mm Dia G.I flanged Rising Main at site.The Pipe shall be hot dip Galvanized, class C (5.4mm thickness) confirming to IS 1239.The job includes providing and fitting of M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16). The flanges shall be double welded both from inside and outside of the pipe using standard electrode of reputed make. Flanges (as per IS 6392/1997 Table: 17) Thickness shall conform to IS 6392 Part 1st Table-17.The flange welding shall be carried out in double layers using Advani/ Esab/L&T-SS Bond make electrodes to form strong welding joint. The electrodes shall be having diameter not less than 4mm, Nuts and Bolts, Rubber Insertion Gaskets of reputed makes to be used between flanged joints. The work includes the cost on account of earth work excavation of all sorts by mechanical means and backfilling for laying the rising main underground as per site requirement
8Fabrication, providing and fitting of washout Tee with arm length as per site requirement but not less than 1.5’x1.5’x1.5’. The Tee shall be fabricated out of G.I C-class pipe with M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16) fastened with weld joints on three ends. Nominal Dia -100 mm
9Fabrication, Providing and fitting of Y- junction / Manifold having length of each arm as per site requirement but not less than 2’x2’x2’ to be fabricated out of hot dip galvanized G.I, (5.4mm thickness) C-Class pipe as per site requirement.The job also includes Providing and welding of M.S flanges to the ends of each arm. The thickness of Flange shall conform to IS 6392 Part 1st Table -17. The flange welding shall be carried out in double layers using Advani/ Esab/L&T-SS Bond make electrodes to form strong welding joint by way of DC arc welding. The job further includes Providing and Fitting of nuts and bolts,) Rubber Insertion Gaskets to be used between flanged joints. Nominal Dia -100mm
10Fabrication, Providing and fitting of Tail piece as per site requirement by Cutting of hot dip galvanized G.I, (5.4mm thickness) C-Class pipe across the section by using pipe cutter/ gas cutter. The job also includes Providing and welding of M.S flanges to the two ends of pipe. The Thickness of flange shall conform to IS 6392 Part 1st Table-17. The flange welding shall be carried out in double layers using Advani/ Esab/L&T-SS Bond Make electrodes to form strong welding joint by using DC arc welding. The job further includes Providing and Fitting of nuts and bolts , Rubber Insertion Gaskets to be used between flanged joints. Nominal Dia-100 mm
11Fabrication, Providing and fitting of 90-120 degree bend/ elbow to be fabricated out of Class C GI pipe (5.4mm thickness) of length as per site requirement and flanged on both endsto make it leak proof. The flanges shall be M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16) and welded on both sides. The job includes nuts, bolts, gaskets etc as per site requirement. Nominal Dia-100mm
12Providing and fitting of Ductile Iron double flanged, Slanted seat swing check valve( NRV) 100mm as per IS 5312. The body shall be of ductile cast iron with fully encapsulated vulcanized EPDM rubber (Approved for drinking water).The valve shall be compatible for buried applications and shall be safe to install in both horizontal and vertical positions. It shall have electrostatic epoxy coating (approved for drinking water) both inside and outside of the valve. Cost on account of Nuts, bolts, gaskets, etc required for the job is included in the scope of work. The job includes providing and fitting of 02 nos.M.Sflangesperfectly adaptable to the inbuilt flanges of the valve which shall be fittedwithRising main of the pumping unit atappropriatespotsaspersiterequirement.The job includes the cost on account of P/F of nuts, bolts and gasket required for the job. Preferably makes : VAG/AVK/Sigma Flow
13Providing and fitting of, Ductile Iron double flanged, non-rising spindle soft seated glandless gate/ sluice valves 100 mm as per IS14846 for regulating the water supply outside the pumping units. The body and bonnet of the valve shall be of ductile iron, wedge with fully vulcanized EPDM rubber (Approved for drinking water) and NBR seal. The Gate/Sluice valveshallbecompatibleforburiedapplicationsandshallbe safe to install in both horizontal and vertical positions It shall have electrostatic epoxy coating (approved for drinking water) both inside and outside of the valve. The valve shall be supplied along with hand wheel. Cost on account of Nuts, bolts, gaskets, etc required for the job is included in the scope of work. The job includes providing and fitting of 02 nos.M.Sflangesperfectly adaptable to the inbuilt flanges of the valve which shallbe fittedwithrising main of the pumping unit atappropriatespotsaspersiterequirement.The job includes the cost on account of P/F of nuts, bolts and gasket required for the job. Preferably makes : VAG/AVK/Sigma Flow
14Fabrication of gantry mechanism and base frame etc by way of providing Structural steel in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete Welded The job also includes painting of complete Structure in one coat of red oxide and 02 coats of enamel metal paint. The job also includes Fabrication of 6’ x 6’ angle iron bed by way of providing and fitting of Structural steel in built up sections , trusses and framed work, including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer all complete welded. The quantity of the steel members like ISMB 200/100 as per IS 808, MS chequered sheet as per IS 2062, ISMC 100, ISMC 75, ISA 50X 50 X5mm, Square bars, railing pipe, MS pipes, angles, tubes, shall be used as per directions of site engineer, same may vary as per site requirement as it is conditional to civil structures being constructed.
15Providing, installation and testing of manual type triple spur gear chain pulley block along with monorail geared travelling trolley having following features Gears:-The hoist shall have precision machine case Hardened alloy steel gear mounted on bearings and housed in a dust proof gear box. The lubrication of gears should be of high viscosity and temperature for longer life of gears. Load Chain:-The load chain be made of high tensile alloy steel having wear resistance and greatest mobility. The chain should be accurately collaborated, tested and have adequate in built factor of safety for safer operation. Load chain wheel:-the load chain well should be double ball bearing supported and Specially designed, perfectly machined wheel providing correct grip ofload chain to makes the hoist most safe and reliable against any failure. The main specifications of C.P Block are given below i. Make = Indeff/Pull lift ii. Capacity= 2 ton iii. No. Of load chain falls= 2 iv. Min. Height of lift= 6 M
16Supply, installation, Testing & commissioning of 950VA Full Sine wave power inverter including Providing / Installation of 12V, 180AH Automotive inverter Battery with trolley and cover. with 2-core 4 mm2 Cu ( 25 m) wiring as per site requirement along withotheraccessorieslikeSS-Combine(02 No’s), 3-pin plugs etc of reputed make for proper fitment and installation of the item. Make : Exide/Luminious/Amaron
17Illumination of Premises: Providing and erection of 9 Mtr long Hot Dip Galvanized octagonal pole (single Section) with bottom 150mm, top 75mmwide,thickness3mmwith70 Microns Zinc coating having inside arrangement for providing of power connection along with following items. 1) 3 Way Terminal Connector 20 Amp. 2) 3 No MCB 8 Amp. The job includes fabrication, providing and fitting of three arm GI structure at the top having 120° angle between arms and each arm having 15° inclination with respect to horizontal plane. Each arm should be of 2’ length and size and shape appropriate as per requirement of the luminary. The job also includes providing and fitting of required length of flexible multi strand 2 mm copper wire from each terminal connector to each holding arm. The pole is mounted on 1:2:4 Cement concreting of size not less than 2’x2’x6” using 04 No anchor bolts of required size not less than 7” in length. The complete job includes earthing in GI Electrode as per relevant IS Code
18Providing, installation, testing and commissioning of area lighting 120 Watt LED (Street Light Type) on top of octagonal pole having following specifications: Input: 90-210 Volts Power Factor: >0.8 Colour Temperature: 4K - 6.5K Beam Angle: 120° - 170° Lumens: >12000 Operating Temperature: -20°C to 60°C The LED is pressure die cast aluminium housing with power coated finish and having Ingress Protection up to IP-68. The LED is properly fitted on the arm of the pole and connected to the copper wire as provided in the high mast pole
19Providing and installation of Junction Box with DP 32 A MCB to serve as Main switch for LED Lighting. The job includes making of electric connection to the circuit.
20Providing and Fitting of 2-Core, 10 Sq. mm XLPE, 11KV grade Armoured Aluminum Cable of various sizes conforming to IS: 7098 part 1st as service line from the HT transformer to control panel including necessary thimblings, crimping, taping etc. To be fitted from auxiliary MCCB of panel to main junction box of octagonal pole.
21a) Providing of good quality bedding for night stay/Shift consisting of: - I) Mattress with warm cover of size 6"x3" (6Kg) white cotton - 02 No’s ii) Quilt with warm cover of size 5"x8" (6Kg)- 02 No’s iii) Pillows with covers - 02 No’s iv) Single bed warm blankets with one sided Fur- 02 No’s The filling material for mattress, quilt and pillow shall be of good quality white cotton b) The job also includes providing of pressure cooker 5ltr (02 Nos), Steel patella (utensil) 5ltrs (02 Nos), cooking heater (01 No.), room heater (01 No), steel buckets 10 liter capacity (01 No), Plastic bucket 10 liter capacity with Mug (02 Nos) each, steel glasses (06 Nos), steel Plates with large spoons and bowls (03 Nos) each, Cup and Saucer set (01 No. Set) and, 5kg Gas cylinder with burner/ stove. The job also includes providing of thermo cool 15’x12’ along with excel matting of 15’x12’ size. The job also includes providing of unbreakable Plastic Chair table set consisting of chairs 04 No’s, heavy Table 01 No. The job also includes providing of good quality safety Door locks (03 No’s).
22Providing, laying & fixing with adhesive/bonding material of insulation rubber mats on the floor of the pump house, covering area around electro- mechanical machinery for safeguarding the life & limb of the workmen due to possible leakage of current & short circuit. The floor surface shall be made good & shall be free from dust, grease, foreign material & moisture free. The mats shall be as per IS 15652:2006 & shall have the following specifications: Composition: Rubber (synthetic mats for electrical purpose) Thickness: - 2.5mm Size: - 1M wide. The rubber mats shall be accepted with manufacturers test certificate. Make : Jyoti / Dunlop
23Providing and fitting of 19 mm thick multilayered ply sheet of size 6 x 3 feet , 2 no’s including cutting , fixing all complete including painting of the play sheet by one coat of primer and two coats of enamel paint
24Supply , installation , commissioning and creation of pole mounted, outdoor type 63 kva capacityLevel II Electric Sub Station as per the amendment No. 4 March 2021 to IS: 1180 (Part 1) 2014 (Fourth Revision). (Rest Technical Specifications as per Annexure "A")
25Providing and fitting G.I Channel /Angle/ Flat of sizes including clamps ( for transformer bed, taping point , brackets of poles etc)
26Supply, Installation, Testing and commissioning of Polymeric Gang operated Air break switch, outdoor type, triple pole, suitable for vertical installation, single break provided with locking arrangement at both ON and OFF position consisting of HT post double insulator, copper or copper alloy high pressure heavy contact assembly, rod with bearings , operating handle and 2 length of 32mm dia. GI pipe conforming to IS 1818 1961, 06 No. of insulators, rated voltage 11KV 200A complete as per IS specs(01 no. at existing tapping point and another at existing substation).
27Supply, Installation, Testing and commissioning of 11KV polymer fuses Set Horn Gap 3-phase 200 A suitable for vertical installation.
28Supply, Installation, Testing and commissioning of Gapless Surge arrestor station class, 10KA, 9KV, LA With polymer housing, Station Type.
29Supply and fitting of 11 KV polymeric composite pin insulator 12 KV, 5KN, Lighting impulse 75KV Positive, and 80 KV Negative , creepage distance 320 mm
30Supply, installation, erection of 9 Mtrs long H.T pole of specifications ST-410 (sp-33). The job further includes drilling of holes for installation of various accessories .wherever required the job further includes G.I wire earthing of pole as per REC standard.
31P/F of Galvanized nuts, bolts of various sizes as per site requirement for fitment of electric substation, poles etc.
32P/F Danger Plate with clamps
33Providing and fixing G.I Barbed wire as anti-climbing devices
34Providing and fitting of Galvanized stay set with 50 X 8 mm Stay Clamp , Guy insulator (2no.), Anchor plate (200X200X6mm) , nuts and bolts , 2 N0- turn buckle , 1.8 m long , 16 mm diameter solid G.I stay rod & 7/3.15 mm dia. G.I stranded wire complete.
35Painting of poles by Red oxide
36Painting of poles Aluminum paint
37P/L of ACSR conductor as per IS 398 (0.05)
38Providing and fitting of PG clamps.
39Supply, installation, testing of 35 Sqr mm XLPE HT cable (ABC type) for 11 KV grade with cross sectional area 3x35 .
40P/F of 11 KV cable termination kit for connecting 35 Sq mm XLPE cable (ABC type) with the existing HT line near tapping point and HT transformer
41Providing andfittingofLTDistributionboxforH.Ttransformerwith100 Ampere , 36KA MCCB For incomer and SFU for outgoing circuits.
42Providing and fitting of three phase, 4 wire commercial Prodigy Meter with all allied Accessories.
43P/I of earthing for electric substation, LT panel and stabilizer comprising of company fabricated earthing electrode as per IS: 3043. The job includes Auguring of bore of required Dia/depth for installation of electrode along with backfill compound mixed with soil and all other items required thereof for achieving the best result. The job includes connecting of electric gadgets through GI strip as per relevant standards. Safe earthing electrode size : 80 mm Dia Length : 2000 mm Back fill compound : 30 kg
44Providing, installation, Testing & commissioning of 415 ±5%V (output), 3 phase Water cooled 50 KVADiesel Generator set as per IS 8528 (2018) for engine and IEC/IS 60034-1 for alternator suitably assembled and fitted in a pollution free acoustic enclosure / canopy of required size as per Ministry of Environment protection rule 1986 read with latest amendments. The DG Set is required to be fitted and tested on load at site(Rest Technical Specifications as per Annexure "A")
45Earth work in excavation by mechanical means in trenches for foundations, drains, pipes, cables etc (not exceeding 1.5m in width) and for shafts, wells, cesspits and the like not exceeding10 Sqm on plan, including dressing of sides and ramming of bottoms lift up to 1.5m, including getting out excavatedearth and disposal of surplus excavated earth asdirected.
46Providing and laying of soling stone
47Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centering and shattering. All works up to plinth level with 1:2:4 mix (1 cement, 2cores sand, 4 graded stone aggregate 20mm nominal size).
48Centering and shattering including strutting, propping etc. and removal of from work for foundation, footings, base for columns
Disclaimer :
We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.
Tell us about your Product / Services,
We will Find Tenders for you

Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy

For Tender Information Services Visit : TenderDetail