Military Engineer Services-MES has published Tender For Works Services For Installation Of Static Aircraft Arresting Gears (Aags) At Af Station Adampur. Submission Date for this Tender is 21-03-2023. Gear Product Tenders in adampur Punjab. Bidders can get complete Tender details and download the document.
| Sr No | CorrigendumDate | Corrignedum | CorrigendumType | NewSubmissionDate |
| 1 | 14-Mar-2023 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 21-03-2023 |
| Sl. No. | Item Description |
| 1 | B/R WORKS |
| 2 | Excavation over areas not exceeding 1.5 metre deep and getting out in soft/loose soil, complete, all as specified and directed. |
| 3 | Excavation over areas exceeding 1.5 metre but not exceeding 3.0 metre deep and getting out in soft/loose soil, complete, all as specified and directed. |
| 4 | Surface excavation in soft/loose soil not exceeding 30 Cm deepand averaging 15 Cm deep and getting out, complete, all as specified and directed. |
| 5 | Surface dressing in soft/loose soil not exceeding 15 Cm deep, getting out and removal of soil/rubbish etc not exceeding 50 metres, complete, all as specified and directed. |
| 6 | Removing surplus excavated materials/ Soils to a distance exceeding 500 metres but not exceeding 1000 metres and depositing where directed, complete, all as specified. |
| 7 | Returning, filling in soft/loose soil, including spreading, leveling, watering and well ramming in layers not exc 25 cm thick each, complete, all as specified and directed. |
| 8 | Material and labour for Plain Cement Concrete 1:4:8type D-2 using 40mm graded crushed stone aggregate as in foundations, filling & mass concrete, in sub base of floors including finishing the surfaces even & fair, complete, all as specified and directed. |
| 9 | Material and labour for Reinforced Ready Mixed Cement Concrete M-35 (Design Mix) as in foundation, including raft footings, foundation beams, plinth beams, bases for column etc., basement slabs, under reamed piles and mass concrete, complete, all as specified and directed. |
| 10 | Material and labour for Reinforced Ready Mixed Cement Concrete M-35 (Design Mix) as in Beams, cantilevers, lintels, columns pillars, piers, posts, struts, chullah hoods, stair case, arches, domes, vaults, shell roofs, arch ribs, folded plates, slabs, balconies, canopies, deck slabs etc. or in similar articles upto 5th floor level, complete, all as specified and directed. |
| 11 | Material and labour for Formwork (to achieve fair finished surfaces) to sides of concretefoundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, complete, all as specified and directed. |
| 12 | Material and labour for Formwork (to achieve fair finished surfaces) to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cms wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work n exc 5 cms wide, complete, all as specified and directed. |
| 13 | Material and labour for Formwork (to achieve fair finished surfaces) to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cms wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 5 cms but n exc 10 cms wide, complete, all as specified and directed. |
| 14 | Material and labour for Formwork (to achieve fair finished surfaces) to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cms wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10 cms but n exc 20 cms wide, complete, all as specified and directed. |
| 15 | Material and labour for TMT steel bars, 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, complete, all as specified and as directed. |
| 16 | All as per the description of item No. 1.14 here-in-above but for TMT steel bars, 6 mm dia to 8 mm dia. |
| 17 | All as per the description of item No. 1.14 here-in-above but for TMT steel bars 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders. |
| 18 | Material and labour for Rolled mild steel work, Fe 410 -W (Gde E- 250) quality A, as in Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment to provide any shape and any size as per site requirement, complete, all as specified and directed. |
| 19 | Supply and fixing Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nuts, any size and length as per site requirement, complete, all as specified and directed. |
| 20 | Note for 1.18: Details of installation of Kit Runway Edge Sheave/ Horizontal Sheave given in Schedule "A" Notes. |
| 21 | Material and labour for painting two coats of water born paint after preparation of surfaces as per manufacturer"s instructions for making lines, dashes, strips, circles, arrows, letters etc. on newely untrated concrete surfaces (Horizontal) and similar other surfaces exc. 10 cm width or girth, with road marking paint (Matt Finish) (water based) conforming to the requirements of IS-164 (1981) of white, golden, yellow, orange, Red and black tint as per the requirement of AF Authoritiesby using fully/semi automatic paint applicator machine (using cold airless spray/ striper machine with minimum two spray guns),complete all as specified and directed . |
| 22 | Note for Srl item No 1.20: Thickness of paint shall be minimum 40 micron (Dry film thickness) for each coat after application. |
| 23 | Make for Srl item No 1.20: Apcotrack manufactured by Asian paints/ Guide line of Berger or equivalent in other makes given here-in-after and approved by GE. |
| 24 | Material and labour for Standard Wall PVC Pipe 10 inch nominal dia (bore) with PVC coupling, 10 Kg/ Sq Cm as a fair lead tube support, complete all as specified and directed. |
| 25 | Material and labour for Standard Wall PVC Pipe coupling suitable for 10 inch nominal dia (bore) PVC Pipe, 10 Kg/ Sq Cm as a fair lead tube support, complete all as specified and directed. |
| 26 | Material and labour for Hardcore of Broken stone or boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface, complete, all as specified and directed. |
| 27 | Material and labour for Plain Cement Concrete 1:3:6type C-2 using 40mm graded crushed stone aggregate as in foundations, filling & mass concrete, all as specified and directed. |
| 28 | Material and labour for Plain Cement Concrete 1:2:4type B-2 using 40mm graded crushed stone aggregate as in foundations, filling & mass concrete, all as specified and directed. |
| 29 | Material and labour for Reinforced Ready Mixed Cement Concrete M-35 (Design Mix) as in slabs, cubid shape of dimension 750 mm x 750 mm x 300 mm, complete, all as specified and directed. |
| 30 | Material and labour for core cutting, cylindrical form of 300 mm dia & 150 mm depth, in cubid of dimension 750 mm x 750 mm x 300 mm slab of Reinforced Ready Mixed Cement Concrete M-35 (Design Mix), complete, all as specified and directed. |
| 31 | Material and labour, applying two coats of synthetic enamel paint over and including a coat of red oxide primer, on new steel surfaces over 10cm width or girth, including preparation of steel surface, complete all as specified and directed. |
| 32 | E/M WORKS |
| 33 | Supply,installation, commissioning and testing Polycarbonate ASTA CPRI approved OEM made Power Distribution system. The panel shall be made of modular POLYCARBONATE THERMOPLASTIC ENCLOSURES including MCBs and indicator lamps. The Enclosure shall be anti-acid & anti corrosive withIP 65 protection. The manufacturer of panel shall submit a copy of ASTA CPRI TEST REPORT IN POLYCARBONATE only.Panel partly assembled by OEM, channel partner or sister concern assembly shall not be accepted. Internally embedded Gaskit shall bemade of polyurethane. The Panels shall be manufactured asapproved in MES and a copy of TYPE TEST REPORT ofboard made out of Polycarbonate thermoplastic panel shall besubmitted in accordance with IEC 60439-1. The ASTA CPRI report shall have mention of following tests performed and passed out satisfactorily- Tempreature Rise, Dielectric Properties, short circuit withstand current- Rate peak & short time withstand current and Rated Conditional Short Circuit Current, Effectiveness of Protective Circuits. The board manufacturer shall submit the copy of type test reprots for Polycarbonate. Thermoplastic Board only shall be used and test Reprots submitted accordingly. Each Board shall have individual routine test report of the manufacturer. The panel shall pass glow wire test 960 degrees Centigrade in accordance with 60695-2-11 (flame retardant and self-extinguishing). Make- Hensel/Rittal/Emitter/ SchneiderINCOMER:- 32 Amp, 4 pole MCB, 10 KA 415VCurve- 01 No Set of LED type indicating lamps - 01 No OUTGOINGS :- 16AMP, MCB TPN 10KA 415V AND 16Amp Industiral Socket with plug CEE-type 5Pin IP54 415 Volt (Make-Walther or Equivalant as approved) with all connectios- 01 No 6 Amp, MCB DP 10KA 240V and Suhcko Socket with Plug 16Amp Industial type 3Pin IP44 230V (Make-Walther or Equivalant as approved) with all connections -01 No |
| 34 | Material and labour for chemical earthing complete with copper earth plate electrode size 900mmx600mmx5mm thick buried directly in ground vertically with top edge of the plate not less than 3.5m below normal ground level (the depth of pit not less than 4.25m below normal ground level), earth plate surrounded by packed layers of mixture of magnesium sulphate -100kg, common salt -200kg, charcoal dust -300kg and also mixing of Bentonite not more than 25 kg with water electrode connected with & including earth lead of copper strip 32x6mm by means of oxycetelance copper brazing as directed by EIC, and other end of the earth lead connected to main switch board or main control board or test or equipemnt, earth lead protected by glavanized iron pipe light grade (ISI) marked 50mm bore alongwith watering pipe 20mm bore GI medium grade (ISI) marked of specified make), funnel with wire, including all necessary excavation & earth work, PCC chamber in plain cement concrete (1:2:4) type B-1 & RCC cover (in lieu of CI cover) all as shown in electical plate No 3 of MES Schedule Part-I (2009), complete all as specified and directed. Note (s):- (i) RCC pit cover shall be pre-cast of RCC (1:2:4) type B-1, 80mm thcik reinforced with XPM not less than 4Kg/Sqm. (ii) PCC chamber shall be constructed at least 500mm away from the edge of earth pit. (iii)Rate shall include copper strip and GI protected pipe upto a length of 7.5m length, beyond 7.5m shall be measured and paid separately. (iv) Earth resistance should be less than 01 Ohm, In case the test results are not found below 01 Ohm, complete earthing will be redone without any extra cost to Govt. (v) For effective visbility identification and traceability of earth (EP) with coresponding earth of eqpt and bldg, markers in metal (Mild steel) shall be provided, earth test of earth pit to be proveded with a colour code. The direction regarding the size, shape and clour of the Mild steel identification board etc, shall be given by the EIC. (vi)All joints of strip shall be brazed on both sides (over lapping) except test point.(vii) On completion of entitre work, contractor shall submit record showing location of earthing, earth value, date of testing, user"s signature etc to engr-in-charge. |
| 35 | Material and labour for Earth continuity conductor or main earthing lead or lightning conductor, 32mmx6mm copper strip, fixed to wall on batten with saddles and fixing screws, PVC/ Porcelain insulators etc or recessed or chases or burried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required, including brazing at all points except test point, complete all as specified and directed. |
| 36 | Supply and laying / fixing , GI pipe light grade 50 mmbore for cable protection fixed to pole/wall or laid under floor/road/pavement,including MS clamps,nut,bolts etc,complete all as specified and directed. |
| 37 | Supply and fixing Test point terminal block made of gun metal or phosphorus bronze of size 75mmx75mmx25mm, drilled and screwed, including 3 Nos. 8mm dia 25mm long hexagonal head screw complete all as specified. |
| 38 | Supply, laying, jointing, testing and commissioningLow Tension (LT)XLPE insulated andarmoured, heavy duty, electric power cable, cross sectional area 35 Sqmm 4 core aluminum conductor 1100 volts grade under ground cable including both side connection with cable lugs etc, laid in trenches, alongpolesorpassing through pipes or laid under floor or through walls etc, complete all as specified and as directed. Note:Excavation & earthork, sand cushioning and bricks for protection of cable shall be measured and paid separately. |
| 39 | Supply, laying, jointing, testing and commissioningLow Tension (LT)XLPE insulated andarmoured, heavy duty, electric power cable, cross sectional area 25 Sqmm 4 core aluminum conductor 1100 volts grade under ground cable including both side connection with cable lugs etc, laid in trenches, alongpolesorpassing through pipes or laid under floor or through walls etc, complete all as specified and as directed.Note:Excavation & earthork, sand cushioning and bricks for protection of cable shall be measured and paid separately. |
| 40 | Excavation in trenches in hard/dense soil not exceeding 1.50 meter wide and not exceeding 1.5 meter in depth; for laying/taking out cables and foundations of poles etcand getting out complete, all as specified. |
| 41 | Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm thick each as in hard/dense soil, complete all as specified. NOTE: For payment purposes volume of returning filling shall be considered after 10% deduction. |
| 42 | Removingof surplussoil / excavated material to a distancenot exceeding 50 metre and depositing where directed complete all as specified. |
| 43 | Clean dry sand laid in trenches/ducts for bedding andcushioning to cable, 8cm in depth before laying the cable and 15 cm in depth after laying the cable including spreading, levelling and consolidation complete all as specified and directed. Note : Consolidated/punned thickness of 18 cm (overall) shall be measured for payment purpose. |
| 44 | Supplying and laying factory made unreinforced precast concrete cable cover LV type, flat , of size 250x150x40mm, laid flat and dryin trenches over the cable for protection, length perpendicular to the direction of cable adjacent to each other, complete all as specified and directed. |
| 45 | Taking out / down old existing HT/LT grade cables any size, laid in trenches, for re-routing or removal to store for credit, including bricks/Precast PCC cable coverfor protection, complete all as specified and directed. |
| 46 | Re-routing and laying old HT/LT grade cables any size retreived from ser item No 2.13 here-in-before, complete all as specified and directed. |
| 47 | Taking outold existing 100mm diaCI pipe including all fittings, with spigot and socket ends and lead joints, laid in trenches, for re-routing or removal to store for credit, including burning out and recovering lead, complete all as specified and directed. |
| 48 | Re-routing and laying old 100mm diaCI pipe retreived from ser item No 2.15 here-in-before, complete all as specified and directed. |
| 49 | Material and labour for cast iron 100mm bore pipes with spigot and socket ends centriugally cast, Class LA, in any length, laid in trenches, complete all as specified and directed. |
| 50 | Supply and fixing LED aviation obstruction light 240 V 50Hz, weather proof as per IP- 65, cast metal body LM-6 alloy with toughened clear transparent hard glass, including fixing arrangement at top of the RCC column 3 mtr height, including PVC 2 core 4 sqmm multistranded Aluminium cable with fixing arrangement of switch control and suitable connection, complete all as specified and directed. (Make : Bajaj BGAV 302 or equivalent as approved). |
| 51 | Supply, fixing and testing bi-directional Runway Edge high intensity light, protrusion height 12.7mm, base diameter of 326 mm, inset depth 150mm,with runway edge shallow base for mounting of bi directional runway edge high intensity light , complete all as specified and directed. Model No: 2x105 watts, 6.6A, 50mm dia reflector and L-850C(L).Make : Safegate Note :- It is specifically brought out that single make of "Safegate" has been included for this item based on the users requirement. Contractor shall ascertain the availabilty of the said light before quoting the tender. No other equivalent make shall be allowed to be incorporated in the work. |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
