Tender For Construction Of Health Subcenter At Village Khor Block Ramnagar District Chitrakoot
Tender Value
24 Lakhs
Estimated cost
Bid Submission
04 Mar 2023
0 days left
EMD
48000
Bank guarantee accepted
Document Fee
1770
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
ramnagar → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Health Subcenter At Village Khor Block Ramnagar District Chitrakoot
BOQ
| Sl. No. | Item Description |
| 1 | Boring, Providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) :300 mm dia piles |
| 2 | Excavation in foundation in ordinary soil (loam clay or sand) including lift upto 1.50 meter and lead upto 30 meter and including filling, watering and ramming of excavated earth into the trenches or into the space between the building and sides of foundation trenches or into the plinth and removal and disposal of sur-plus earth as directed by the Engineer incharge up to a distance of 30 meters from the foundation trenches. |
| 3 | Providing & laying cement concrete in 1:4:8 (1 cement: 4 coarse sand: 8 graded stone aggreagate 40mm nominal size) including supply of all materials,labour and T & P etc. required for completion of work and curing complete including cost of form work in foundation and floors |
| 4 | Filling of carted earth in plinth including supply of necessary quantity of sand from a distance not exceeding 5km from the side of work and including watering dressing etc. required for proper completion of work. |
| 5 | Sand filling in plinth including supply of necessary quantity of sand from a distance not exceeding 8km from the site of work and including watering ,dressing etc rate to include cost of all materials, labour T&Petc. Required for proper completion of work . |
| 6 | R.c.c. workwith cement approved coarse sandand2cm. (3/4\") guageapproved stoneballastin the proportion of 1:1.5:3(M-20) in lintel & plinth bandsexcludingsupply of reinforcement and its fixing and binding the same with 24 B WG bindingwireand including necessary centeringand shuttering etc.and also including supply of all materials,labour andtools and plants etc, required forproper completion of the works. strength of the concrete shall not beless than M-20 |
| 7 | R.c.c. workwith cement approved coarse sandand2cm. (3/4\") guageapproved stoneballastin the proportion of 1:1.5:3(M-20) in slabexcludingsupply of reinforcement and its fixing and binding the same with 24 B WG bindingwireand including necessary centeringand shuttering etc.and also including supply of all materials,labour andtools and plants etc, required forproper completion of the works. strength of the concrete shall not beless than M-20 |
| 8 | R.c.c. workwith cement approved coarse sandand2cm. (3/4\") guageapproved stoneballastin the proportion of 1:1.5:3(M-20) in lighter beamexcludingsupply of reinforcement and its fixing and binding the same with 24 B WG bindingwireand including necessary centeringand shuttering etc.and also including supply of all materials,labour andtools and plants etc, required forproper completion of the works. strength of the concrete shall not be less than M-20 |
| 9 | Class-150 brick work in 1:6 (one cement and six coarse sand sand of 2.25 fineness modulus) mortar infoundation & plinth including supply of all materials, labour and T & P etc required for proper completion of the work. |
| 10 | Class-150 brick workin 1:4 cement & coarse sandcement of 1.50 fineness modulus mortar infoundation & plinth including supply of all materials, labour and T & P etc required for proper completion of the work. |
| 11 | Class-150 brick work 1:6 cement & coarse sand of 1.50 fineness modulus mortar insuper-structure including necessarycutting andmouldingofbricksrequiredandalsoincludinghoney comb brick workthickness of wall more than one brick and for extra labour to above items. Supply of materials, Labour, tools and Plants etc.requried for proper completion of the work. |
| 12 | Class-150 brick workin 1:4 cement & coarse sandcement of 1.50 fineness modulus mortar insuper-structure including necessarycutting andmouldingofbricksrequiredandalsoincludinghoney comb brick workthickness of wall more than one brick and for extra labour to above items. Supply of materials, Labour, tools and Plants etc.requried for proper completion of the work. |
| 13 | Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work(whennot includedin anover all rates )wroughttorequired shape as necessary including bending for proper completion of thework andincluding supply of steel itswastage and over lapping and hookes required for completion of the work. |
| 14 | 12 mm cement plaster onbrick work minium thickness not less than 10 mm with mix: 1:4 (1 cement: 4 coarse sand) (Plinth plaster) |
| 15 | 15mm Cement plaster with cement mortar in proportion of 1:6 cement & coarse sand of single coat onfor interior plastering/ Rough face upto floor two level including internal rounded angles chamfers, and rounded angles not exceeding 80mm in girth and finished even and smooth.INC. ROUGH FACE |
| 16 | 12mm Cement plaster with cement mortar in proportion of 1:6 cement & coarse sand of single coat on fair surface for exterior plastering upto floortwo level including internal rounded angles chamfers, and rounded angles not exceeding 80mm in girth and finished even and smooth |
| 17 | Providing and laying of 8 to 10 mm thick ivory or light shade vitrified tiles of 600mm x600mm size in flooring or skirting laid with 1:3 cement mortar (1cement :3 coarse sand ) finishing with cement slurry & pigment grouting & Polishing complete i/c supply of all material labour T&P etc. required for proper completion of work .excluding base concrete |
| 18 | Kota Stonework in Flooring and Skirting (machine cut egdes veneer work) for wall lining upto 10.00 M height,backing filled with a grout of 12mm thick cement mortar 1:3 (1 cement :3 coarse sand) and jointed with cement mortar 1:in flooring 25 mm thick & joint filled with 1:2 (1 cement:2 Stone dust) including rubbing and polishing complete. |
| 19 | Supply and fixing 6mm (1/4\"\") China white glazed tiles in flooring and skirting laid with ratio 1:3 cement and approved coarse sand finished with white cement slurry jointing and polishing complete, including supply of all materials,labour and T&P etc.Required for proper completion of work. |
| 20 | 2.5cm thick 1:2:4 cement concrete floor with cement approved coarse sand & 2cm graded dala stone grit laid in planels finished with 3mm floating coat of neat cement bor cement and marble dust in ratio of 5:1 as specificover and excluding base concrete and removing any overlapping mortar at the joints of the panels if any giving them a uniform finish, including supply of all materisls labour, T&P etc. required for proper completion of work |
| 21 | Supply & fixing of flush door commercial quality conforming of IS 2202 part 1 (1983) including fixing of wooden cleats & stoppers and including fixing & adjustment of hinges ,bolts,locls,handles springs,fitting with necessary screws to be supplied departmentally35 mm thick Single leaf/double leaf |
| 22 | Supply of Fixing MS grill of a approved quality and drawing made of flat iron not bigger then 20 x 4mm size including supply of materials fabrication labour T&P and also one coat of red oxide paint complete in all respect as per direction of Engineer in chrage for proper completion of work at site. |
| 23 | Supply of Fixing ofApprovedMS Z-Section windows and ventilators excluding cost of glass panes but including supply of all materials its fabrication nuts and bolts,hole fast for proper completion of work as per direction of engineer in charge and also including cost of handle stays rod etc.and one coat of red oxide paint complete in the respectsite of work. |
| 24 | Supply of Fixing of MS angle Iron door,window ventilation frame made of approved MS angle Iron wrought to required from including drilling hole welding and recetting where necessary and also including supply of all material such as steel hinges required size nut bolts etc and also including all taxes wastage and one coat of red oxide paint complete in all respect as per direction of Engineer in charge for proper completion of work at site of work. |
| 25 | Fixing of Door, windows/ventilators chaukhats in position.(a) Door chaukhats |
| 26 | Fixing of Door, windows/ventilators chaukhats in position. (b) Window chaukhats |
| 27 | Fixing of Door, windows/ventilators chaukhats in position.(c) Ventilator chaukhats |
| 28 | One coat Priming coat and three coat oil distemper on new work including supply of all material labour T&P etc required for proper completion of work. |
| 29 | Finishing wall with water proof cement paint of aprooved make and quality on new work with two coats but each coat of water proof cement paint after the first two coats to give an even shadeincluding supply of materials, labour, T&P etc. required for proper completion of work. |
| 30 | Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete. |
| 31 | Providing & fixing stainless steel sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc complete. (a) 300mm x 16mm |
| 32 | P/Fixing stainless steel tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as / IS : 1868) transparent or dyed to required colour or shade with necessary screws etc.250 mm x 10mm |
| 33 | Providing & fixing stainless steeldoorhandleswith screwsand 150mm long.SI marked |
| 34 | Painting or varnishing new WOOD OR STEELin small areas with one coat of ready mixed priming paint and one coat of approved superior quality ready mix paint (2nd quality synthetic enamel paint of approved brand such as British paint ,Shalimar Asian or equivalent as approvedby E/I ) or varnish including supply of all material labour T & P etc required for proper completion of the work Paint to be used should confirm the ISI No. 103-1950 . |
| 35 | S/F of 4.0 mm thick Panes of glass with and Including Atul or Equivalent ISI mark quality putty and brads and spring incluing supply of all materials labour and T&P etc. required for proper completion of work. |
| 36 | Construction of drain of size of size 150 x 150 mm along with apron including excavation,base concrete 1:4:8 in thickness of 7.5cm of and brick work in foundation 1:4( 1 cement : 4 coarse sand) and brickwork in half brick thick in foundation 25mm thick cement concrete (1:2:4 mix) flooring base and 20mm thick plaster (1:2) finished with neat cement. (Analysis) |
| 37 | S/F of glass strips for flooring 35mm wide & 3.15mm thick. |
| 38 | 12mm bearing plaster with cement mortar in proportion of 1:4 cement & Coarse sand of single coat for interior plastering upto floor two level including internal riunded angles chamfers and rounded angles not exceeding 80mm in girthand finished even & smooth inc. 2 coat of white washing supply of all material t & p etc equired for proper completion of work. |
| 39 | Providing and laying cement concrete in 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and curing complete, Including cost of form work. |
| 40 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Ordinary cement without any pigment |
| 41 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 42 | Making grooves 10 to 12mmwide and 8mm deep in plaster of the wallor in ceiling vertically or horizontally as required. |
| 43 | Making drip course in sunshade or FACIA as per direction as Engineer in Charge. |
| 44 | S/F Brick bats in soak pit |
| 45 | Providing and LayingRubbleMoulded ZigZag type Interlocking concrete Block Pavements having thickness 80 mm as per drawing and Technical Specification Clause 1504. |
| 46 | Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 |
| 47 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required For European type W.C. pan with white plastic seat and lid |
| 48 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require For White Vitreous China Flat back wash basin size 550x 400 mm with a pair of 15 mm C.P. brass pillar tap. |
| 49 | Providing and fixing white vitreous china padestal for wash basin completely recessed at the back for the reception of pipes & fittings. |
| 50 | Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete.Semi rigid pipe a) 32mm dia |
| 51 | Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete.Semi rigid pipe b) 40mm dia |
| 52 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 53 | Providing & fixing PTMT towl rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fitting arrangement of approved quality and colour. 600 mm. long towl rail length of 645 mm. width 78 mm. and effective height of 88 mm, weighing not less than 190 gms. |
| 54 | Providing and fixing PTMT Liquid soap container 109 mm wide ,125 mm high and 112 mm distance from wall of standerd shape with bracket of the same material with snap fittings of approved quality and colour weighing not less than 105 gms |
| 55 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever requiredKitchen sink with drain board of size 510x1040x200mm |
| 56 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion . (i) Single socketed pipes.a) 110mm diameter |
| 57 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over PVC sheet 1m x 1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement,punning,rounding the edges and making and finishing the outlet complete.a) 110mm |
| 58 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.a) 110mm |
| 59 | Supply and fixing of UPVC S.W.R. pipe type-B confirming to IS-13592 including jointing the pipes with rubber ring,lubricant and UPVC SWR cupler confirming to IS-14735. Also including excavation of treanches cutting of walls and holes and repairing the walls,floors and refilling the trenches as before but excluding supply and cost of other fIttlings such as elbow,bend,tee and y-tee including supply of al marerial labour and T&P.Required for proper completion of work.90 mm O.D. |
| 60 | Supply and fixing of UPVC S.W.R. pipe type-B confirming to IS-13592 including jointing the pipes with rubber ring,lubricant and UPVC SWR cupler confirming to IS-14735. Also including excavation of treanches cutting of walls and holes and repairing the walls,floors and refilling the trenches as before but excluding supply and cost of other fIttlings such as elbow,bend,tee and y-tee including supply of al marerial labour and T&P.Required for proper completion of work.110 mm O.D. |
| 61 | Supply and fixing of UPVC S.W.R. pipe nahni trap size 100x75,110/90 mm confirming to IS-14735 self cleaning design fixed in PCC 1:2:4 and supply and fixing of 125 mm dia heavy duty CP brass jali. |
| 62 | Supply and fixing of UPVC S.W.R. plain bend confirming to IS-14735. Size 90 mm |
| 63 | Supply and fixing of UPVC S.W.R. plain bend confirming to IS-14735. Size 110 mm |
| 64 | Supply and fixing of UPVC S.W.R. plain tee confirming to IS-14735.Size Supply and fixing of UPVC S.W.R. plain tee confirming to IS-14735.90x90x90 mm |
| 65 | Supply and fixing of UPVC S.W.R. plain tee confirming to IS-14735.Size 110x110x110 mm |
| 66 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.internal work Exposed on wall 20mm dia nominal outer dia pipes |
| 67 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge.Concealed work including cutting chases and making good the walls etc.15mm dia nominal outer dia pipes |
| 68 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge.Concealed work including cutting chases and making good the walls etc.20mm dia nominal outer dia pipes |
| 69 | Providing and fixing 45 cm long unplasticised PVC connection pipe with brass unions. a) 15mm nominal bore |
| 70 | Providing & fixing CP brass bib cock of approved quality conforming to IS 8931 (a) 15mm nominal bore |
| 71 | Providing & fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS 8931. (a)15mm nominal bore |
| 72 | Providing & fixing C.P. Brass extension nipple(size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. |
| 73 | Providing and fixing gun metal gate valve with wheel of approved quality.20 mm dia nominal bore |
| 74 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete.25 mm nominal bore |
| 75 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank. IS:12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 76 | Providing and fixing square mouth S.W. Gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 Kg and frame to be not less than 2.70 Kg as per standard design 150 x 100 mm. size P type With Sewer bricks conforming to IS : 4885 |
| 77 | Wiring point for light with 1.5 sq.mm FR P.V.C. insulated multistrandsingle core Copper Conductor cable in PVC conduit with 1.5 sq.mm. FRLSH PVC insulated multistrand copper conductor cable as earthing wire drawn inside the conduitpartly concealedin wall&partlylaidin slab along with the reinforcement before concreting,complete with piano typeswitch & ceiling rose / angle / batten holder on 3 mm thick phenolic laminated backelite sheet etc complete in all respects as directed, including matching color wash |
| 78 | Wiring point for fan with 1.5 sq.mm FRLSH PVC insulated multistrandsingle core Copper Conductor cable in PVC conduit pipe partly concealedin wall&partlylaidin slab along with the reinforcement before concreting,complete with 1.5 sq.mm. FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduitpartly concealedin wall&partlylaidin slab along with the reinforcement before concreting,complete with piano typeswitch & ceiling rose / angle / batten holder on 3 mm thick phenolic laminated backelite sheet etc complete in all respects as directed, including matching color wash |
| 79 | Wiring point for exhaust fan with 1.5 sq.mm FRLSH PVC insulated multistrandsingle core Copper Conductor cable in PVC conduit pipe partly concealedin wall&partlylaidin slab along with the reinforcement before concreting,complete with 1.5 sq.mm. FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduitpartly concealedin wall&partlylaidin slab along with the reinforcement before concreting,complete with piano type switch & ceiling rose / angle / batten holder on 3 mm thick phenolic laminated backelite sheet etc complete in all respects as directed, including matching color wash |
| 80 | Wiring point for plug 1.5 sq.mm FRLSH PVC insulated multistrandsingle core Copper Conductor cable in PVC conduit pipe partly concealedin wall&partlylaidin slab along with the reinforcement before concreting,complete with 1.5 sq.mm. FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduitpartly concealedin wall&partlylaidin slab along with the reinforcement before concreting,complete with modular typeswitch & socket etc, complete in all respect including matching colour wash. |
| 81 | Supply & wiring of submains with two number2.5 sq.mm FRLSH PVC insulated 1100 V grade single core multistrand copper conductor cable in 20mm dia heavy duty (2mm thick)PVC conduit with 1 Number 1.5 sq.mm. FRLSH PVC insulated 1100 V grade multistrand copper conductor cable as earth continuity wire drawn inside the conduitcomplete in all respect. |
| 82 | Supply & wiring of submains with two number4 sq.mm FRLSH PVC insulated 1100 V grade single core multistrand copper conductor cable in 20mm dia heavy duty (2mm thick)PVC conduit with 1 Number 2.5 sq.mm. FRLSH PVC insulated 1100 V grade multistrand copper conductor cable as earth continuity wire drawn inside the conduitcomplete in all respect. |
| 83 | Supply and Fixing of LED Tube Light with batten suitable for up to 1X22 watt LED tube light fitting complete including tube on surface complete in all respect. 1 X 22W CAT-AAA |
| 84 | Supply and Fixing of LED BULB with batten suitable for up to 9 TO12 watt LED tube light fitting complete including tube on surface complete in all respect. |
| 85 | Supply of Ceiling Fan with motor of A.C. Permanent insulation capacitor rating confirming BEE 5 Star rating and IS:374/79 and also comply with IS:1709/1984 with latest amendment. The rated volage 220/240 volts, 50 Hz, 1-ph A.C.the fan assemble should consists of down rod blades, shackle canopies etc and with double ball bearing system.BEE 5 Star rated-1200mm sweep |
| 86 | Supplyand burying safe earthing Electorde T-19 (HotDip Galvanized), Length 2000 mm, outer pipe 50mm, inner pipe 25, terminal Dia 12mm ,outer G.I.pipe of 16 swg and inner GI pipe of12swg withHotDipGavanized up to 100 mirconfilled with crystalline conducative mixture (CCM) having anti corrosive & conducative property with 50 kgs activated soil (BFC) capable of reducingthe soilresistivitywith good mixture ofretaning capacity along with 30 cm squre C.I. frame with hinged cover & masonryhousing (from electode terminaltoswitchboard , cost of 25 x 3 G.I. strip will be extra) Make:As approved in U.P.P.W.D. & C.P.R.I. Certified |
| 87 | Supplying & Laying of 25mmx3mm G.I. Strip from earth electrode in ground as required complete in all respects. |
| 88 | Supply & fixing of two number 8 SWG G.I. wire for earthing purpose as required complete in all respects. |
| 89 | Supply and fixing of 6 Amp to 32 Amp MCB(10KA)C Curve .6 - 32 amp.Cat. A |
| 90 | Supply and fixing of 40 Amp. 4 Pole MCB (10KA)CAT A |
| 91 | Supply and fixing of surface/ flush mounting 4 way TPN distribution board with additional metal doorwithout MCB complete in all respect, as directed at site by Engineer Incharge.CAT A |
| 92 | Supply & fixing of Crimping, solder, less, copper ton electroplated lugs of Dowel/ismail make suitable for 1.5 sqmm to 6sqmm cables, including tapping with insulating tape,etc. complete in allrespects. |
| 93 | Supply and fixing of single pole MCB blanking plate CAT A |
| 94 | Supply and fixing of power plug with 20A/250 V flush type modular switch and 5 Pin 20 A/250 Volt flush type universal modular socket switch on concealedM.S. box including supply of all material, labour T & P etc required for proper completion of work. |
| 95 | Erection and testing of ceiling fan and regulator for room height upto 3.5mts. including supply of 3mm thick G.I. down rod 19mm dia duly painted, complete in all respects. |
| 96 | Erection and testing exhaust fan on the exhisting hole with suitable size of rag bolts nuts and washers etc. complete in all respects. |
| 97 | Supply & fixing of 16 gauge M.S.drum duly painted including making hole in the wall for exhaust fan and finishing properlyetc. complete as required. |
| 98 | Supply & fixing hexagonal/Round G.P. Fan box of approved make made up of 1.0 mm thick ISI marked G.P. Sheet spot welded four to Eight holes of 25.4mm for pipe entry of the box. Holes should be semi-shuttered type with 0.5mm G.P. Sheet made upper & lower cover duly screwed fitted with 300mm round zink coated M.S. Bar x 12mm & brand name should be embossed. Fixing with wiring conduit laid in the R.C.C. roof before concreting alongwith supply of all material labour, T & P etc required for proper completion of the work. |
| 99 | Supplyfixingofelectronic fan regulator (Modular) 120-280 V. ISImarked, on the existing switch board including making connetion, required material, labour T/P etc for proper completion of work to the satisfaction of Engineer in charge of work. |
| 100 | Supply and laying of aluminium conducter, PVC insulated armoured, served, sheeted cable 1000 bolts grade at a depth of 750mm below ground level over a cushion of 75mm thick sand alround and protected with burnt bricks on sides and top on surface, the cable run shall be fixed on M.S. clamps etc. of suitable size. or as directed by the Engineer-Incharge, complete in all respect. the armouring of the cable shall be properly connected with the earth conductor by clamps etc. 16 sqmm 4 core |
| 101 | Supply & fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respects. The armouring of the cable shall be properly connected with the earth as per direction of Engineer-Inchage.16 sqmm 4 core |
| 102 | Supplying and fixing of Palm / pin type copper tin plated cables sockets (lugs) to the cable leads, insuslating with tape and making of connections etc. complete in all respects as per direction of Engineer-Incharge.16 Sq.mm |
| 103 | Supply & erection of AC 230/250 Volts, 50 Hz exhaust fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required-Make: USHA Cat No. TURBO JET DLX 300mm sweep. |
| 104 | India marks-II hand ISI market with Cylinder & Conection road complete |
| 105 | Supply of 110mm dia plain PVC (6 kg/sqcm) Pressure |
| 106 | Supply of 63mm dia plain PVC (6 kg/sqcm) Pressure |
| 107 | 50mm dia PVC strainer 4mt Long ridded with stander trap & Spaciales |
| 108 | Supply of PVC Soket 110m dia |
| 109 | Nylon mesh narial rope around stariner |
| 110 | Supply of medium class GI pipe 32mm B class |
| 111 | Providing necessary boaring T&P including making arrangement of water for boaring 200mm dia bore hole by Rig machine in all type of starta complete item 30 metre B.G.L |
| 112 | Providing necessary boaring T&P including making arrangement of water for boaring 200mm dia bore hole by Rig machine in all type of starta complete item Beyond 30 metre |
| 113 | Supply of labour T&P and jointing & lowering of PVC pipe consisting of 110mm & 50 mm dia bore long ribbed PVC Strainer & Cavity complete 30 metre B.G.L |
| 114 | Supply of labour T&P and jointing & lowering of PVC pipe consisting of 110mm & 50 mm dia bore long ribbed PVC Strainer & Cavity complete Beyond 30 metre |
| 115 | Supply of labour T &P and jointing & lowering of PVC pipe consisting of110mm & 50mm dia bore ribbed PVC strainer & cavity complete |
| 116 | Development of bore by manual labour till discharge is free from turbity complete item |
| 117 | Supply & using of PVC cemnt solvent |
| 118 | Supply of steel wire rope |
| 119 | Installation of India Marka-II hand pump over the bore hole as per direction of E/I and Installtion |
| 120 | PUMPING SET KSB make submersible pump set suitable for Installation jn bore well of ran 110 mm inner dia preferably moreand having under |
AI Tender Summary
Tender Timeline
Feb 20, 2023
11:30 IST
Tender Published
Tender notice published.
CompletedMar 04, 2023
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedMar 04, 2023
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender