Directorate of Training and Employment has published Bids Are Invited For Tools And Equipment -Connecting Screwdriver , Neon Tester 500 V. , Screw Driver Set , Insulated Combination Pliers , Insulated Side Cutting Pliers , Long Nose Pliers , Soldering Iron , Electrician Knife , Tweezers , Digital Multim. Submission Date for this Tender is 23-02-2023. Earth Moving Machinery Tenders in Agra Uttar Pradesh. Bidders can get complete Tender details and download the document.
Sl. No. | Item Title | Item Description |
1 | Connecting screwdriver | 10 X 100 mm |
2 | Neon tester 500 V. | 500 V |
3 | Screw driver set | Set of 7 |
4 | Insulated combination pliers | 150 mm |
5 | Insulated side cutting pliers | 150mm |
6 | Long nose pliers | 150mm |
7 | Soldering iron | 25 Watt, 240 Volt |
8 | Electrician knife | 100 mm |
9 | Tweezers | 150 mm |
10 | DigitalMultimeter | 3 3-4 digit ,4000 Counts |
11 | Soldering Iron Changeable bits | 15 Watt, 240 Volt |
12 | De-soldering pump electrical heated, manual operators | 230 V, 40 W |
13 | Steel rule graduated both in Metric and English Unit | 300 mm, |
14 | Tweezers – Bend tip | Standard |
15 | Steel measuring tape | 3 meter |
16 | File flat bastard | 200 mm |
17 | Round Nose pliers | 100 mm |
18 | Hacksaw frame adjustable | 300 mm |
19 | Handsaw 450mm | Hand Saw - 450 mm |
20 | Hand Drill Machine Electric with Hammer Action | 13 mm |
21 | Bench Vice | Bench Vice - 125 mm |
22 | Bench Vice | Bench Vice - 100 mm |
23 | Bench Vice | Bench Vice - 50 mm |
24 | DC Regulated Variable Programmable DC Power Supply | 0-30V-3A |
25 | LCR meter Digital Handheld | Standard |
26 | Signal Generatorwith Digital Display for Frequency Amplitude | 10 Hz to 100 Khz, 50-600 Ohms output impedance |
27 | Analog multimeter | Standard |
28 | Clamp meter | 0 - 10 A |
29 | Autotransformer | 15 Amps |
30 | Analog Component Trainer | Breadboard for Circuit design with necessary DCAC power supply Sine, Square, Triangle Modulating Signal Generator and Simulation Software |
31 | Milli Ammeter AC | 0 – 200 mA |
32 | Milli Ammeter DC | 0 – 500 mA |
33 | Op Amp trainer | Standard |
34 | Rheostats various values and ratings | Standard |
35 | Different types of electronic and electrical cables, connectors, sockets, terminations. | Standard |
36 | Different types of Analog electronic components, digital ICs, power electronic components, general purpose PCBs, bread board, MCB, ELCB | Standard |
37 | SMD Soldering and De soldering Station with necessary accessories | Standard |
38 | Single Phase Contactors Relays MCB DOL Starter | Standard |
39 | PAM, PPM,PWM trainer kit | Standard |
40 | AM-FM Commercial radio receivers | Standard |
41 | Various analog and digital ICs useful for doing project works mentioned in the digital and analog IC applications modules | Standard |
42 | Different types of electronic and electrical cables, connectors, sockets, terminations. | Standard |
43 | Seven segmentDPM trainer | Standard |
44 | LCD based DPM | Standard |
45 | SMPSof different make | Standard |
46 | UPS | Standard |
47 | Mobile phone Trainer | 2G -3G-4G Dual SIM GSM Handset. Frequency measurement and band verification. Real time Mobile Operation |
48 | Cell phone power source with charger chords for different cell phones | Standard |
49 | LED TVTrainer kit | 20-inch full HD LED Color Television, PAL- NTSC video formats, complete block diagram of a LED TV system, Study board indicating various sections of LED TV along with the test points and switch faults Trouble shooting in different sections. |
50 | LED TV 21” | Standard |
51 | Home theatre system | Standard |
52 | Solar Training Kit- Simulator | WithbuiltinmetersforDCV, DCA, AC multifunction Meter for ACI, ACV, Power, Frequency, Protection Circuits, BS- 10 terminals for makingthe connection, Single- Dual axis tracking system Charge ControllerPWM based MPPT, Charging StageBulk, Absorptions and Float voltages 0 to 245V variable AC |
53 | Steel Rule with metric and British graduation | 150 mm, Stainless steel |
54 | Divider spring type | 150 mm |
55 | Scriber | 150 mm |
56 | Screw driver | 150mm insulated flat type |
57 | Chisel cold flat | 20 mm X 150 mm High carbon steel |
58 | Hammer ball peen with handle | 450 grams 1 lb |
59 | File flat - second cut | 250 mm |
60 | File half round second cut | 150 mm. |
61 | Safety goggles. | Standard |
62 | Straight edge steel | 300 mm or above |
63 | Spirit Level metal Type - 2 | 300 mm Basic Length Accuracy 0.1mm-Meter |
64 | Stud Extractor EZY - out | Set of 8 |
65 | Combination Set | 300 mm |
66 | Micrometer inside with extension rods. | Accuracy 0.01 mm with extension rods up to 150 mm |
67 | Vernier caliper | 150 mm |
68 | Vernier bevel protractor Blade with Acute Angle Attachment | 300 mm |
69 | V-Block pair with clamps | 150 x 100 x 100 mm |
70 | Punch letter set. | 3 mm |
71 | Drill twist Taper shank | 8 mm to 20 mm by 0.5 mm H.S.S. |
72 | Taps and dies complete set | 5, 6, 8, 10 and 12mm set of 5 |
73 | File triangular smooth | 200 mm |
74 | File round second cut | 200 mm |
75 | File square second cut | 250 mm |
76 | File triangular second cut. | 200 mm |
77 | File flat second cut safe edge. | 300 mm |
78 | File flat bastard | 200 mm |
79 | File flat bastard. | 300 mm |
80 | File half round second cut. | 250 mm |
81 | File half round bastard. | 250 mm |
82 | File round bastard. | 250 mm |
83 | File hand second cut. | 150 mm |
84 | File card. | 3x5 size, brass or steel wire |
85 | Wooden handle forged Soldering Iron copper bit. | 230V, 250 W, 350 gm |
86 | Spanner- Double Ended | 6x7, 8x9, 10x11, 12x13, 14x15, 16x17, 18x19, 20x22 |
87 | Spanner adjustable | 150 mm |
88 | Interchangeable ratchet socket set | 12 mm driver, sized10-32 mm set of 18 socket and attachments. |
89 | Double Ended tubular Box spanner set with Tommy bar. | A-F 6-25 mm set of 10 Tommy Bar Dia. 6, 8, 10, 12, 14, 16 |
90 | Clamp toolmaker | 5 cm and 7.5 cm set of 2. |
91 | Clamp C | 200 mm |
92 | Scraper flat | 150 mm |
93 | Scraper triangular | 150 mm |
94 | Scraper half round | 150 mm |
95 | Chisel cold crosscutand diamond point. | 9 mm X 150 mm |
96 | Chisel cold flat | 9 mm X 100 mm |
97 | Chisel cold round nose | 9 mm X 100 mm |
98 | Pipe wrench | 400 mm |
99 | Machine vice - Swivel Base | 100 mm |
100 | Machine vice - Swivel Base | 125 mm |
101 | Sleeve drill Morse | No. 0 - 1, 1 - 2, 2 - 3, 3 - 4, 4 - 5 |
102 | Vice bench | 150 mm |
103 | Metal rack | 1820 x 1820 x 450 cm |
104 | Torque wrench Standard-Ratchet type | 14 to 68 Nm |
105 | Power tools for fastening | Capacity 10-18mm |
106 | Different Profile gauges Plate type - For demonstration | Metric standard |
107 | Knurling tool Diamond, straight and Diagonal | Standard |
108 | Indexable boring bar with inserts | 1inch shank |
109 | Temperature gauge | Range 0 - 150°C |
110 | Dowel pin straight | Dia. -1inch Length -4inch Mat Stainless Steel |
111 | Standard Tap screws | M3, M4, M5, M6, M8, M10, M12, M14, M16 |
112 | Lapping plate | Dia. -6 inch |
113 | Medium carbon Heat treated alloy steel Metric Studs and bolts along with nuts for display of standard length May be manufactured in-house | M6, M8, M10, M12, M14, M16 Standard |
114 | Caps screws | M6, M8, M10, M12 |
115 | Drill gauges | Letter drill gauge A to Z, Number drill gauge 1 to 60, Metric drill gauge 1.5mm to 12.5mm, 30 holes |
116 | Cast Iron Globe Valve Flanged type | 150NB, Class 150 Flange ANSI125-B16.1 |
117 | C.I. Sluice - Gate valve flanged type | 150NB, Class 150 Flange ANSI125-B16.1 |
118 | Stop cock | 25NB 2-way, Threaded end |
119 | Slip on Forged steel Flange | 150NB, ANSI-B16.5, Class 150 |
120 | Bolt and Nut with washer May be manufactured in- house | M20x2.5x90Long part thread - Hex. Head |
121 | Jigs and Fixture sample-For demonstration May be manufactured in-house | Standard |
122 | Pulleys for V-belt or Flat belt | to fit on 50mm dia. Shaft with key slot |
123 | Steel keys May be manufactured in- house | to fit with key slot of shaft and pulley |
124 | Damaged old spur gear | to fit 50mm dia. Shaft |
125 | V-belt and Flat belt | to fit on pulley |
126 | Packing gasket | PTFE gasket roll small size |
127 | Washer, clutch, keys, jib, cotter andcirclip | minimum 25mm size, carbon steel material |
128 | Drill Drift May be manufactured in- house | 200mm hardened and black finish |
129 | Bearing different types | each type of diameter 25mm min. |
130 | Lifting sling | 8mm Nominal Dia. Single leg sling |
131 | Bearing extractor | Universal gear puller 2 or 3 jaws adjustable |
132 | Pulley extractor | Universal gear puller 2 or 3 jaws adjustable |
133 | Digital Micrometer outside. | 0 - 25 mm L.C. 0.001 mm. |
134 | Comparators Gauge - Dial Indication with Stand and Bracket. | LC 0.01mm |
135 | Engineer s try square knife-edge | 150 mm Blade |
136 | Surface roughness comparison plates | N1 - N12 Grade |
137 | Digital Vernier caliper | 0 - 200 mm L.C. 0.01 mm Optional |
138 | Vernier Bevel protector | Range 360deg, LC. 5min150mm blade |
139 | Carbide Wear Block. | 1 mm - 2 mm |
140 | SS and SC centre lathe all geared with minimum specification | Centre height 150 mm and centre distance 1000 mm along with 3 and 4 jaw chucks, auto feed system, safety guard, taper turning attachment, motorized coolant system, lighting arrangement and standard accessories. |
141 | D.E. pedestal Grinding machine with wheels rough andsmooth | 2 H.P.-3Phase-415V, 1500 rpm,250 dia. wheel |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail