Tender For Development Of Iot Lab At Nsut East Campus Geeta Colony, Delhi 110031, delhi-Delhi

Development Of Iot Lab At Nsut East Campus Geeta Colony, Delhi 110031--- 1 Civil Work: 1 Providing And Fixing False Ceiling At All Height Including Providing And Fixing Of Frame Work Made Of Special Sections, Power Pressed From M.S. Sheets And Galvanized With Zinc Coating Of 120 Gms / Sqm ( Both Side Inclusive ) As Per Is : 277 And Consisting Of Angle Cleats Of Size 25 Mm Wide X 1.6 Mm Thick With Flanges Of 27 Mm And 37Mm, At1200 Mm Centre To Centre, One Flange Fixed To The Ceiling With Dash Fastener 12.5 Mm Dia X 50Mm Long With 6Mm Dia Bolts, Other Flange Of Cleat Fixed To The Angle Hangers Of 25X10x0.50 Mm Of Required Length With Nuts & Bolts Of Required Size And Other End Of Angle Hanger Fixed With Intermediate G.I. Channels 45X15x0.9 Mm Running At The Spacing Of 1200 Mm Centre To Centre, To Which The Ceiling Section 0.5 Mm Thick Bottom Wedge Of 80 Mm With Tapered Flanges Of 26 Mm Each Having Lips Of 10.5 Mm, At 450 Mm Centre To Centre, Shall Be Fixed In A Direction Perpendicular To G.I. Intermediate Channel With Connecting Clips Made Out Of 2.64 Mm Dia X 230 Mm Long G.I. Wire At Every Junction, Including Fixing Perimeter Channels 0.5 Mm Thick 27 Mm High Having Flanges Of 20 Mm And 30 Mm Long, The Perimeter Of Ceiling Fixed To Wall / Partition With The Help Of Rawl Plugs At 450 Mm Centre, With 25Mm Long Dry Wall Screws @ 230 Mm Interval, Including Fixing Of Gypsum Board To Ceiling Section And Perimeter Channel With The Help Of Dry Wall Screws Of Size 3.5 X 25 Mm At 230 Mm C / C, Including Jointing And Finishing To A Flush Finish Of Tapered And Square Edges Of The Board With Recommended Jointing Compound , Jointing Tapes , Finishing With Jointing Compound In 3 Layers Covering Upto 150 Mm On Both Sides Of Joint And Two Coats Of Primer Suitable For Board, All As Per AnufacturerS Specification And Also Including The Cost Of Making Openings For Light Fittings, Grills, Diffusers, Cutouts Made With Frame Of Perimeter Channels Suitably Fixed, All Complete As Per Drawings, Specification And Direction Of The Engineer In Charge But Excluding The Cost Of Painting With :12.5 Mm Thick Tapered Edge Glass Reinforced Gypsum ( Grg ) Board Conforming To Is: 2095- ( Part 3 ) :1996 ( Boards With Bis Certification Marks ) 2 2 Providing & Fixing False Ceiling At All Heights With Grg ( Glass Fibre Reinforced Gypsum ) False Ceiling Tiles Of Size 595X595 Mm Of Approved Texture, Design And Patterns Having Moisture Content Less Than 2%, Humidity Resistance Of 99%, Nrc0.50 To 0.75 As Per Is 8225:1987, Non Combustible As Per Bs 476 ( Part 4 ) -1970 And Light Reflectance Of 85% ( Minimum ) To Be Laid In True Horizontal Level Suspended On Interlocking Metal T-Grid Of Hot Dipped Galvanised Iron Section Of 0.33Mm Thick ( Galvanized @ 120 Grams Per Sqm Including Both Sides ) Comprising Of Main-T Runners Of Size 15X32 Mm Of Length 3000 Mm, Cross - T Of Size 15X32 Mm Of Length 1200 Mm And Secondaryintermediate Cross-T Of Size 15X32 Mm Of Length 600Mm To Form Grid Module Of Size 600 X 600 Mm, Suspended From Ceiling Using Galvanisedmild Steel Items ( Galvanizing @ 80 Grams Per Sqm ) I.E. 50 Mm Long, 8 Mm Outer Diameter M-6 Dash Fasteners, 6 Mm Dia Fully Threaded Hanger Rod Upto 1000 Mm Length And L-Shape Level Adjuster Of Size 85X25x2 Mm.Galvanised Iron Perimeter Wall Angle Of Size 24X24x0.40 Mm Of Length 3000 Mm To Be Fixed On Periphery Wall / Partition With The Help Of Plastic Rawl Plugs At 450 Mm Center To Center And 40 Mm Long Dry Wall Wood Screws. The Work Shall Be Carried Out As Perspecifications, Drawing And As Per Directions Of The Engineer-In-Charge.With Semi Perforated 12 Mm Thick Micro Tegular Edged Grg False Ceiling Tiles. 3 3 Distempering With 1St Quality Acrylic Distemper, Having Voc ( Volatile Organic Compound ) Content Less Than 50 Grams / Litre, Of Approved Brand And Manufacture, Including Applying Additional Coats Wherever Required, To Achieve Even Shade And Colour.One Coat 4 4 Providing And Placing Of Modular Workstations System Of Size 1500Mm ( W1 ) X 1500Mm ( W2 ) X 600Mm ( D ) X 750 Griha Compliant Having Following Specifications. - Main Partition Panel Having 4 Horizontal Blocks And Consists Of Vertical Extrusions 2Nos And Horizontal Extrusions 5 Nos Made Of 1.2Mm Thick Aluminium With Duly Powder Coated At Every Division Of Tile / Block. Each Panel Shall Have Bottom Frame Fabricated For 52.4Mm Panel Comprises Of 2 Nos. L-Channels Made Of 2Mm Thick Crca ( Cold Rolled, Cold Aneeled ) Steel ( Is: 513 ) , Formed Plates Of 3Mm Thick Hot Rolled Steel ( Is: 2062 ) & Erw Steel Tube Of Size 35X15x1.6Mm Thick In Oval Cross Section ( Is: 7138 ) Welded Together. The Complete Bottom Frame Shall Be Powder Coated With An Average Of 50-60 Microns Thickness Of Epoxy Powder Coating. The Bottom Frame Is Bolted With The Upright Verticals. Each Panel Is Provided With 2Nos Legs Of Height 120Mm Are Fixed At The Bottom Frame Of The Panel. Legs Construction-Adjustment Of The Height By 50Mm. It Will Be Coated With 45-50Micron ------------------------ Locking:10 Lever Cam Lock & Central Rh Locking With Actuator & Lock Channel Mechanism. Top Panel : 0.8Mm Thick Metal Straight Edge Top. Castors : Swiveling Non-Lockable 4Nos Castors Mounted Below The Body Shell. The Total Drawer Unit Is Finished With Epoxy Polyester Powder Coated To The Thickness Of 50 Microns ( + / -10 ) . The Product Should Be Complete And As Per Approved Sample And As Per The Direction Of Engineer-In-Charge. 5 Supplying And Placing In Position Faculty Table Of Following Specifications. Overall Dimension Of The Main Desk Shall Be - 1800Mmw X 750Mmd X 1050Mm Hthe System Shall Be A Desk-Based System With A Platform Understructure Made Up Of A Combination Of Ms. Tubes And Plates. The Product Should Be Greenpro Certified And Should Be Listed In Griha Product Catalogue In The Following Category Griha V.3 Criteria: 34; Griha V.2015 Criteria: 31 & Svagriha Criteria: 14. Understructure - The Slanted Legs Are Connected To The Understructure With The Help Of Pdc Connectors To Provide A Stable And Sturdy Base For The Worktops. Modesty Panel Shall Be Of Acrylic ( 8 Mm Thick Acrylic Both Side Frosted ) Or Of Metal 1.2 Mm Thick Crca. Worktop - Worktop Shall Be Made Of 25Mm Thick Pre-Laminated Board Conforming To Is: 12823. All The Edges Of Work Surface Shall Be Provided With Machine Pressed 2 Mm Thick Pvc Lipping Glued With Hot Melt Eva Glue.The Worktop Shall Be Complete With Provisions For Screen Mounting As Well As For Wire Management On The Workstation. Provisions For Fixing Of The Switches Shall Be On The Wire Tray / Channel. A Wire Management - It Shall Be A Part Of The Understructure And Can Be In The Form Of Enclosed Metal Tray Or 2 Level Enclosed Channel To Provide Concealed Wire Management Throughout The Cluster Formation. Wire Riser Leg Or Independent Wire Risers Shall Be Provided As Per The Layout Structure.Ccess Flaps With Soft Closing Technology Shall Be Provided On The Table Tops To Access The Switch Points On The Tray. Pedestal Having 3 Drawers Unit Having Flat Metal Front And Top With Central Locking. The Drawer Unit Consists Of 2Box And 1File Drawers. The Overall Size Of The Drawer Units Is 450Mm ( W ) X 435Mm ( D ) X 646Mm ( H ) . Construction & Material Of Drawer Unit :Welded Assembled Of 0.8Mm Thick Crca For Body Shell, Drawer Front & Tray, Front Side Stiffener, Rear Side Stiffener & Bottom, 1.2Mm Thick Crca Top Stiffene, Bottom Stiffener, Drawer Fronts & Metal Front Straight Edge. All Drawers With Double Extension Precision Ball Slide Shall Be Provided. For Drawer Pulling, Side Wise Tapered Recess Provided In Shell Behind Drawer Fronts. Locking:10 Lever Cam Lock & Central Rh Locking With Actuator & Lock Channel Mechanism. Top Panel : 0.8Mm Thick Metal Straight Edge Top. Castors : Swiveling Non-Lockable 4Nos Castors Mounted Below The Body Shell. The Total Drawer Unit Is Finished With Epoxy Polyester Powder Coated To The Thickness Of 50 Microns ( + / -10 ) . 6 6 Supplying And Placing Stool Of Following Specifications:The Seat Shall Be Made Up Of 1.2±0.1Cm Thick Flat Plywood With Moulded Polyurethane Foam And Are Upholstered With Replaceable Synthetic Leather Covers. The Dimensions Of Seat Shall Be Diameter 40.0 Cm And Adjustments Are 360° Revolving Type. The Back Foam Shall Be Designed With Contoured Lumbar Support For Extra Comfort. The Upholstery Shall Be Available In Synthetic Leather. The Dimensions Of Back Shall Be 45.0 Cm ( W ) Covered With Polyurethane Foam. The Hr Polyurethane Foam Shall Be Moulded With Density = 45 + / -2 Kg / M3and Hardness Load 16 ± 2 Kgf As Per Is:7888 For 25% Compression. The Manual Height Adjustment Shall Be Very Easy To Operate With A Help Of A Knob. It Should Be Easily Locked At The Most Comfortable Position. The Five-Prong Pedestal Shall Be Fabricated From 0.2 ± 0.02 Cm Thick Hr Sheet ( Is : Dd 1079 / Hr ) , Powder Coated ( Dft 40-60 Microns ) And Shall Be Fitted With An Injection Moulded Black Polypropylene Hub Cap And 5 Nos. Twin Wheel Castors. The Pedestal Shall Be 55.0±0.5Cm Pitch-Circle-Diameter ( 65.0±-1.0Cm With Castors ) , Circular-Foot-Ringof Dia 52.0±0.2Cm Shall Be Made Up Of Dia 1.9±0.2 X0.12±0.0096Cm Thk Ms Erw Tube For Foot Support In High-Base Stool.The Twin Wheel Castors Shall Be Injection Moulded In Black Nylon. Overall Dimensions Shall Bewidth- 65.0Cm, Depth- 65.0 Cm, Height- 88.0 To 99.5 Cm, Seat Height- 67.0 To 78.5 Cm. 7 7 Supplying And Placing Revolving Chair With The Cushioned Seat Assembly Consists Of Seat Base Moulded In Glass-Filled Poly-Amide, Moulded Polyurethane Foam & Upholstered With High Stretch Knitted Polyester Fabric. The Cushioned Back Assembly Consists Of Back Inner Moulded In Polypropylene In-Situ Moulded With Polyurethane Foam & Upholstered With High Stretch Knitted Polyester Fabric.* Full Back Size : 45.5 Cm. ( W ) X 53.0 Cm. ( H ) *Seat Size :48.5 Cm. ( W ) X 47.0 Cm. ( D ) The Hr Polyurethane Foam Used In Seat And Back Cushion Is Moulded In Density 45±2 Kg / M3, And Hardness Load 16 ± 2 Kgf As Per 15:7888 For 25% Compression.The Seat And Back Are Firmly Connected To The Base Frame And Are Cantilevered In Such A Way That It Gives A Multi-Dimensional Movement Possibility Just With A Simple Lean On The Sides Or Back, Without Need For Complex Manual Adjustments. The Cantilevered Seat Offers Impact Cushioning While Sitting And Synchronises With The Back Movement During Posture Changes. The 5 Shaped Spines Moulded In High Strength Glass-Filled Poly-Amide And The Spine Connector Moulded In Glass-Filled Poly-Am ) De Form The Back-Spine Structure Involved In Multi-Dimensional Recline Motion.The Variable Tilt Angle Recline Motion Can Be Adjusted With 3 Position Tilt Limit Feature Which Is Inbuilt In Seat Base And The Tension ( Return Force ) Is User Weight Dependent. The Assembly Consists Of Armrest Housing Sliding Over The Armrest Structure, Both Moulded In Glass-Filled Poly-Amide. The Height Adjustment Feature Is Button Operated Having Adjustment Of 6.6±0.5Cm. The Armrest Top Is Made Up Of Integral Skin Pu Moulded Over Plastic Inner Moulded In Glass-Filled Poly-Amide.The Seating Height Can Be Adjusted With A Pneumatic Gas-Lift Having An Adjustment Stroke Of 9.2 ± 0.3 Cmthe Pedestal Is Injection Moulded In Glass-Filled Poly-Amide And Fitted With 5 Nos. In Wheel Castors. The Pedestal Is 66.0±0.5 Cm. Pitch Centre Diameter And 76.0±1.0 Cm. With Castors. 5 Nos. Twin Wheel Castors Are Injection Moulded In Poly-Amide Having 5.0±0.1Cm Heel Diameter And Assembled To The Pedestal. The Product Shall Be From One Of The Approved Make Of Godrej, Hermanmiller, Steel Case, Delform Or Vitra Only. 8 8 Supplying And Placing Almirah Of Following Specifications : Almirah Steel Shall Have An Overall Size Of916mm ( W ) X486mm ( D ) X1980mm ( H ) With Welded Construction. It Should Have The Shelf Thickness Of 0.7 Mm, Back Thickness Of 0.8Mm, Door Thickness Of 0.8Mm ( High Yield Strength ) And All Other Components Shall Have A Thickness Of 0.9Mm. These Components Shall Be Made Of Crca ‘D’ Grade High Yield Strength As Per Is:513. The Almirah Steel Should Have A Mazak Handle And Three Way Locking Mechanism With Shooting Bolts. It Should Have A Height Wise Adjustable Shelf Mounting Which Shall Have A Uniformly Distributed Load Capacity Of Max 40 Kg. It Should Also Have A M10 Screw Type Leveller With Hex Plastic Base. The Finishing Shall Include Epoxy Powder Coated To The Thickness Of 50 Microns ( + / - 10 ) . Plenty Of Colour Options And Shelving Options Shall Be Available. 9 9 Supplying And Placing Locker Of Following Specificationsoverall Size Of 4 Door Locker Shall Be 380Mm ( W ) X450mm ( D ) X1830mm ( H ) .Stackability Shall Have Add- On Units That Can Be Stacked Width Wise To Form Bank Of Lockers Having Common Side Panel. Locking Shall Have 10 Lever Cam Lock With Lock Lever Plus Option Of Hasp Arrangement . Material Shall Be Crca 0.6 Mm Thickness . Construction Shall Be Rigid Knockdown Construction , Shelf Shall Be Uniformly Distributed Load Capacity Per Each Shelf Level Is 35 Kg Maximum . Finish Shall Be Epoxy Polyester Powder Coated To The Thickness Of 50 Microns . Handle / Label Holder Shall Be Aesthetically Appealing Snap Fit Absplastic Handle . Ventilation Shall Be Attractive Punched Pattern For Ventilation . 10 10 Supplying And Placing Wall Storage Of Following Specifications Overall Dimensions Of Wall Storage 900 W Shall Be 900 Mmw X 328Mm D X 785 Mmh . The Construction Shall Be Aesthetically Appealing Completely Knock Down Construction Made From 0.6 Mm Thk. Crca As Per Is - 513 . Horizontal Stiffener Shall Be Made From 1.2 Mm Thk. Crca As Per Is - 513 . The Doors Shall Be Madefrom 18 Mm Thk. Interior Grade Pre-Laminated Board As Per Is - 12823 Or 18 Mm Thk . Plain Particle Board As Per Is -3087 With 0.6 Thk. With 0.6 Mmthk. Decorative Laminate And 0.6 Mm Thk. Backing Laminate As Per Is - 2046 On Either Side . All Edges Shall Be Duly Sealed With 2 Mm Thk. Pvc Edge Banding . Twodoor Withsingle Lockon Rhdoor . Locking Shall Be 10 Lever Cam Lock Lever At The Bottom Of The Door .Shelving Shall Be Heightwise Adjustable Shelf 1 No. Uniformly Distributed Load Capacity Of 25 Kg Udl .The Finish Shall Be Epoxy Powder Coated To The Thickness Of 50 Microns . The Doors Shall Be 448 Mm W X 18 Mm D X 783 Mm H Rh Side Door With Lock. 448 Mm W X 18 Mm D X 783 Mm H Lh Side Door W / Olock . The Doors Shall Be Madefrom 18 Mm Thk. Interior Grade Pre-Laminated Board As Per Is - 12823 Or 18 Mm Thk . Plain Particle Board As Per Is -3087 With 0.6 Thk. With 0.6 Mmthk. Decorative Laminate And 0.6 Mm Thk. Backing Laminate As Per Is - 2046 On Either Side . All Edges Shall Be Duly Sealed With 2 Mm Thk. Pvc Edge Banding .It Shall Have Two Door With Single Lock On Rh Door 11 11 Providing And Fixing Manual Chain Operated Roller Blinds Consisting Of 100% Polyester Fabric, Fabric Thickness 0.50 Mm Fabric Weight = 270 Gsm+- 5% , Fabric Width 230Cms, Tearing Strength 4.5 Kgf Warp, Bursting Strength 34 Kgf, Colour Fastness To Light 5 To 6 Grade In Position Of Standard Quantity And Approved Shade / Colour Including Necessary Accessories, Ms Clamps.Screws And Drilling Etc. As Required All Complete As Per Directions Of Engineer-In -Charge. ( Approved Make: Vista / Mac / Sd ) 12 Electrical Worksh-01 ( Wiring And Accessories ) 1 Wiringforlightpoint / Fanpoint / Exhaustfanpoint / Callbellpoint With1.5 Sq.Mmfrls Pvc Insulated Copper Conductor Single Core Cable In Surface / Recessedmediumclasspvcconduit, Withmodular Switch, Modularplate, Suitablegiboxandearthing The Point With 1.5 Sq.Mm Frls Pvc Insulated Copper Conductor Single Core Cable Etc. As Required.A Group C 13 2 Wiringforgroupcontrolled ( Looped ) Lightpoint / Fan Point / Exhaustfan Point / Call Bell Point ( Without Independent Switch Etc. ) With 1.5 Sq. Mm Frls Pvc Insulated Copper Conductor Single Core Cable In Surface / Recessed Pvc Conduit, And Earthing The Point With 1.5 Sq. Mm Frls Pvc Insulated Copper Conductor Single Core Cable Etc. As Required.A Group C 14 3 Supply And Fixing Suitable Sizegi Box With Modular Plateand Coverinfrontonsurfaceorinrecess Includingprovidingandfixing6pin, 15 / 16Amps Modular Socket Outlet And 15 / 16 Amps Modular Switch , Connection Etc . As Required . 15 4 Wiring For Light / Power Plug With 2X4 Sq. Mm Frls Pvc Insulated Copper Conductor Single Core Cable In Surface / Recessedmediumclasspvcconduitalong With1no.4Sq.Mmfrlspvcinsulatedcopper Conductor Single Core Cable For Loop Earthing As Required. 16 5 Wiring For Light / Power Plug With 4X4 Sq. Mm Frls Pvc Insulated Copper Conductor Single Core Cable In Surface / Recessedmediumclasspvcconduit Alongwith2nos.4Sq.Mmfrlspvcinsulated Copper Conductor Singlecorecablefor Loopearthing As Required. 17 6 Wiringforcircuit / Submainwiringalongwithearth Wire With The Following Sizes Of Frls Pvc Insulated Copper Conductor, Single Core Cable In Surface / Recessed Medium Class Pvc Conduit Asrequired.A ) 2 X 2.5 Sq. Mm + 1 X 2.5 Sq. Mm Earth Wire 18 B ) 2 X 10 Sq. Mm + 1 X 6 Sq. Mm Earth Wire 19 7 Supplying And Drawing Following Sizes Of Frls Pvc Insulated Copper Conductor, Single Core Cable Inthe Existing Surface / Recessedsteelconduitasrequired A ) 3 X 2.5 Sq. Mm 20 B ) 3 X 4 Sqmm 21 C ) 6 X 4 Sq. Mm 22 8 Supplying And Fixing Modular Blanking Plate , On The Existing Modular Plate & Switch Box Excluding Modular Plate Etc. As Required. 23 9 Supplying And Fixing Following Modular Switch / Socketontheexistingmodularplate&Switchbox Including Connectionsbutexcludingmodularplate Etc. As Required.A 5 / 6 A Switch 24 B 3 Pin 5 / 6 A Socket Outlet 25 10 Supplying And Fixing Following Modular Base & Coverplateonexistingmodularmetalboxesetc.As Required.A 3 Module 26 B 6 Module 27 11 Supplying And Fixing Following Size / Modules, Gi Box Alongwith Modular Base & Cover Plate For Modular Switches In Recess Etc. As Required.A 12 Module ( 200Mmx150mm ) 28 Sh-02 ( Distribution Board ) 12 Supplying And Fixing Following Way, Horizontal Type Three Pole And Neutral, Sheet Steel, Mcb Distribution Board, 415 Volts, On Surface / Recess, Complete With Tinned Copper Bus Bar, Neutral Bus Bar, Earth Bar, Din Bar, Interconnections, Powder Painted.A ) 6 Way ( 4 + 18 ) , Double Door 29 13 Supplyingandfixing5ampsto32amps, Rating, 240 / 415Volts, CCurve, Miniaturecircuitbreaker Suitableforinductiveloadoffollowingpolesinthe Existing Mcb Db Complete With Connections, Testing And Commissioning Etc. As Required.A ) Single Pole 30 14 Supplying And Fixing Folowingrating Double Pole 240 Volts, Mcbin The Existing Mcb Db Complete With Connections, Testing And Commissioning Etc. As Required.A ) 63 Amp Doublepole Mcb 31 15 Supplyingandfixingfollowingratingdoublepole 240Volts, Residual Current Circuit Breaker ( Rccb ) , Having Sensitivity Of 30 Ma In The Existing Mcb Db Complete With Connections, Testing And Commissioning Etc. As Required.A ) 63 Amp Dp Rccb 32 16 Supplying And Fixing 63 Amps Rating, 240 / 415 Volts, 10 Ka, “C” Curve, Miniature Circuit Breaker Suitable For Inductive Load Of Following Poles In The Existing Mcb Db Complete With Connections, Testing And Commissioning Etc. As Required.A Single Pole 33 17Supplying And Fixing Tpn Mcb 63 A Rating, 240 / 415 V, 10 Ka, C Curve, Miniature Circuit Breaker Suitable For Inductive Load Of Following Poles In The Existing Mcb Db Complete With Connections, Testing And Commissioning Etc. As Required 34 Sh-03 Light / Fan Fixtures ) 18 Dismantling The Existing Worn Out / Defective Fittings From The Ceiling Andsitc Of Minimum 36 Watt Aluminium Slim Energy Efficient Led Panel Light Fitting Made Of Crca Sheet, Steel Housing Duly Powder Coatedhaving System Efficacy Minimum 100 Lumen / Watt Lm79, Color Temp 6500 Deg K, Symmetric Glare Free Full Opal Diffuser, Ip 20 Illumination In The False Ceiling, Recess Mounting Suitable For Fitting In The 600Mm X 600Mm Square Existing Space Having Complete With All Standard Accessories Including Drivers Etc. Complete As Required. 35 19 Sitc Of Minimum 20 Watt Aluminium Slim Energy Efficient Led Panel Light Fitting Made Of Crca Sheet, Steel Housing Duly Powder Coatedhaving System Efficacy Minimum 100 Lumen / Watt Lm79, Color Temp 6500 Deg K, Symmetric Glare Free Full Opal Diffuser, Ip 20 Illumination In The False Ceiling, Suspended Mounting Suitable For Fitting In The Existing Space Having Complete With All Standard Accessories Including Drivers Etc. Complete As Required. 36 20 Supply, Installation, Testing And Commissioning Of 1200 Mm Sweep, Bee 5 Star Rated, Ceiling Fan With Brush Less Direct Current ( Bldc ) Motor, Class Of Insulation: B, 3 Nos. Blades, 30 Cm Long Down Rod, 2 Nos. Canopies, Shackle Kit, Safety Rope, Copper Winding, Power Factor Not Less Than 0.9, Service Value ( Cmm / W ) Minimum 6.85, Air Delivery Minimum 215 Cmm, 350 Rpm ( Tolerance As Per Is : 374-2019 ) , Thd Less Than 10%, Remote Or Electronic Regulator Unit For Speed Control And All Remaining Accessories Including Safety Pin, Nut Bolts, Washers, Temperature Rise=75 Degree C ( Max. ) , Insulation Resistance More Than 2 Mega Ohm, Suitable For 230 V, 50 Hz, Single Phase Ac Supply, Earthing Etc. Complete As Required. 37 Sh-04 ( Earthing ) 21 Earthing With Copper Earth Plate 600Mm X 600Mm X 3Mm Thick Including Accessories And Providing Masonryenclosurewithcoverplatehavinglocking Arrangementandwateringpipeof2.7Mtrlongetc With Charcoal, Coke And Salt As Required. ( For Computer Earthing ) 38 22 Providing And Fixing 25 Mm X 5 Mm Copper Strip On Surface Or In Recess For Connections Etc. As Required. 39 23 Providing And Fixing 25 Mm X 5 Mm Copper Strip In 40 Mm Dia G.I. Pipe From Earth Electrode Including Connection With Brass Nut, Bolt, Spring, Washer Excavation And Re-Filling Etc. As Required. 40 Sh - 05 ( Networking ) 24 Supplying And Drawing Of Utp 4 Pair Cat 6 Lan Cable In The Existing Surface / Recessed Steel / Pvc Conduit As Required. 1 Run Of Cable ( Make:- Commscope Systimax Only ) 41 25 Providing And Fixing 24 Port Loaded Straight Patch Panel Of Height 1U In The Existing Data End Rack Including Making Connections, Channel Labellingetc. Complete As Required. 42 26 Supplying And Fixing Following Modular Switch / Socket On The Existing Modular Plate & Switch Box Including Connections But Excluding Modular Plate Etc. As Required.A Rj 45 Information Outlet 43 27 Supplying And Fixing Following Modular Base & Cover Plate On Existing Modular Metal Boxes Etc. As Required.A 1 Or 2 Module 44 28 Providing And Fixing Stranded Low Smoke Halogen Cordage Unshielded Cat 6 Modular Patch Cord Of Length 1 Mtr With Plug Insertion Life Not Less Than 750 Times And Minimum Plug Retention Force Of 133N I / C Making Connections Etc. Complete As Required. 45 29 Providing And Fixing Stranded Low Smoke Halogen Cordage Unshielded Cat 6 Modular Patch Cord Of Length 2 Mtr With Plug Insertion Life Not Less Than 750 Times And Minimum Plug Retention Force Of 133N I / C Making Connections Etc. Complete As Required. 46 30 Sitc Of12u Floor Mount Network Rack With Accessories ( Make:- Rittal / Apw / Emerson ) 47 31 Sitc Of 24 Port Non-Poe Managed Access Switchs Per Specifications In Annexure -A As Per Directions Of Engineer In-Charge 48 32 5 Years 24X7 Onsite Comprehensive Warranty And Support For24 Port Non-Poe Managedaccess Switch As Per Specifications Provided And Installed Under This Contract As Required. A ) For 1St Year 49 B ) For 2Nd Year 50 C ) For 3Rd Year 51 D ) For 4Th Year 52 E ) For 5Th Year 53 33 Suppling And Fixing Of Following Sizes Of Medium Class Pvc Conduit Along With Accessories In Surface / Recess Inculding Cutting The Wall And Making Good The Same In Case Of Recessed Condit As Required.25Mm Pvc Conduit 54 34 Supplying And Fixing Of Upvc Trunking Of Size 100 X 50 Along With Accessories On Surface Complete As Required. 55 35 Dismantling & Buy Back Of Old & Defective Following Items As Per Required. A 4 X 1 Light Fitting. 56 B Ceiling Fans

Refer document

INR 75959.0 /-

INR 37.97 Lakhs /-

Name of work :- Development of IoT Lab at NSUT East Campus Geeta colony,East Colony during the year 2022-23.

Sl. No.	Item Description
1	Civil Work: 1 Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per anufacturer"s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge Glass Reinforced Gypsum (GRG) board conforming to IS: 2095- (Part 3):1996 (Boards with BIS certification marks)
2	2 Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987,Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm,cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as perspecifications, drawing and as per directions of the Engineer-in-Charge.With semi perforated 12 mm thick micro tegular edged GRG false ceiling tiles.
3	3 Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. One coat
4	4 Providing and placing of modular workstations system of size 1500mm (W1) X 1500mm (W2) X 600mm (D) x 750 GRIHA compliant having following specifications. - Main Partition panel having 4 horizontal blocks and consists of Vertical extrusions 2Nos and Horizontal extrusions 5 nos made of 1.2mm thick aluminium with duly powder coated at every division of tile/block. Each panel shall have Bottom frame fabricated for 52.4mm panel comprises of 2 nos. L-channels made of 2mm thick CRCA (Cold Rolled, Cold Aneeled) steel (IS: 513), formed plates of 3mm thick Hot Rolled steel (IS: 2062) & ERW steel tube of size 35x15x1.6mm thick in oval cross section (IS: 7138) welded together. The complete bottom frame shall be powder coated with an average of 50-60 microns thickness of epoxy powder coating. The Bottom Frame is bolted with the Upright verticals. Each Panel is provided with 2Nos Legs of height 120mm are fixed at the bottom frame of the panel. Legs Construction-adjustment of the height by 50mm. It will be coated with 45-50micron ------------------------ Locking:10 lever Cam Lock & Central RH locking with actuator & lock channel mechanism. Top Panel : 0.8mm thick Metal Straight Edge Top. Castors : Swiveling non-lockable 4Nos Castors mounted below the body shell. The Total drawer unit is finished with Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10). The product should be complete and as per approved sample and as per the direction of Engineer-In-charge.
5	Supplying and Placing in position Faculty Table of following Specifications. Overall Dimension of the Main Desk Shall be - 1800mmW x 750mmD x 1050mm HThe system shall be a desk-based system with a platform understructure made up of a combination of MS. Tubes and plates. The product should be Greenpro certified and should be listed in Griha product catalogue in the following category GRIHA V.3 criteria: 34; GRIHA V.2015 criteria: 31 & SVAGRIHA criteria: 14. Understructure - The slanted legs are connected to the understructure with the help of PDC Connectors to provide a stable and sturdy base for the worktops. Modesty panel shall be of Acrylic (8 mm thick Acrylic both side frosted) or of Metal 1.2 mm thick CRCA. Worktop - Worktop shall be made of 25MM thick Pre-Laminated Board conforming to IS: 12823. All the edges of work surface shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glue. The worktop shall be complete with provisions for screen mounting as well as for wire management on the workstation. Provisions for fixing of the switches shall be on the wire tray/channel. A Wire Management - It shall be a part of the understructure and can be in the form of enclosed metal tray or 2 level enclosed channel to provide concealed wire management throughout the cluster formation. Wire riser leg or independent wire risers shall be provided as per the layout structure.ccess flaps with soft closing technology shall be provided on the table tops to access the switch points on the tray. Pedestal having 3 Drawers Unit having flat metal front and top with Central locking. The Drawer Unit consists of 2Box and 1File Drawers. The Overall size of the Drawer Units is 450mm(W) X 435mm(D) X 646mm(H). Construction & Material of Drawer Unit :Welded Assembled of 0.8mm thick CRCA for Body Shell, Drawer Front & tray, Front Side Stiffener, Rear Side Stiffener & Bottom, 1.2mm thick CRCA Top Stiffene, Bottom stiffener, Drawer Fronts & Metal Front Straight Edge. All Drawers with Double extension precision ball slide shall be provided. For Drawer pulling, side wise tapered recess provided in shell behind Drawer Fronts. Locking:10 lever Cam Lock & Central RH locking with actuator & lock channel mechanism. Top Panel : 0.8mm thick Metal Straight Edge Top. Castors : Swiveling non-lockable 4Nos Castors mounted below the body shell. The Total drawer unit is finished with Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10).
6	6 Supplying and placing stool of following specifications:The seat shall be made up of 1.2±0.1cm thick flat plywood with moulded Polyurethane foam and are upholstered with replaceable synthetic leather covers. The dimensions of Seat shall be Diameter 40.0 cm and Adjustments are 360° Revolving type. The back foam shall be designed with contoured Lumbar support for extra comfort. The upholstery shall be available in synthetic leather. The dimensions of Back shall be 45.0 cm (W) covered with polyurethane foam. The HR polyurethane Foam shall be moulded with density = 45 +/-2 kg/m3and Hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The manual height adjustment shall be very easy to operate with a help of a knob. It should be easily locked at the most comfortable position. The five-prong pedestal shall be fabricated from 0.2 ± 0.02 cm thick HR sheet ( IS : DD 1079/HR ), powder coated ( DFT 40-60 microns ) and shall be fitted with an injection moulded black Polypropylene Hub Cap and 5 nos. twin wheel castors. The Pedestal shall be 55.0±0.5cm pitch-circle-diameter(65.0±-1.0cm with castors), Circular-foot-ringof dia 52.0±0.2cm shall be made up of dia 1.9±0.2 x0.12±0.0096cm thk MS ERW Tube for foot support in High-base stool.The twin wheel castors shall be injection moulded in Black Nylon. Overall dimensions shall beWidth- 65.0cm, Depth- 65.0 cm, Height- 88.0 to 99.5 cm, Seat Height- 67.0 to 78.5 cm.
7	7 Supplying and placing revolving chair with the cushioned seat assembly consists of seat base moulded in glass-filled Poly-amide, moulded Polyurethane foam & upholstered with high stretch knitted polyester fabric. The cushioned back assembly consists of back inner moulded in Polypropylene in-situ moulded with Polyurethane foam & upholstered with high stretch knitted polyester fabric.* Full Back Size : 45.5 cm. (W) x 53.0 cm. (H) *Seat Size :48.5 cm. (W) x 47.0 cm. (D)The HR polyurethane foam used in seat and back cushion is moulded in Density 45±2 kg/m3, and hardness load 16 ± 2 kgf as per 15:7888 for 25% compression.The seat and back are firmly connected to the base frame and are cantilevered in such a way that it gives a multi-dimensional movement possibility just with a simple lean on the sides or back, without need for complex manual adjustments. The cantilevered seat offers impact cushioning while sitting and synchronises with the back movement during posture changes. The "5" shaped spines moulded in high strength glass-filled Poly-amide and the spine connector moulded in glass-filled Poly-am)de form the back-spine structure involved in multi-dimensional recline motion.The variable tilt angle recline motion can be adjusted with 3 position Tilt Limit feature which is inbuilt in seat base and the tension (return force) is user weight dependent. The assembly consists of armrest housing sliding over the armrest structure, both moulded in glass-filled Poly-amide. The height adjustment feature is button operated having adjustment of 6.6±0.5cm. The Armrest Top is made up of integral skin PU moulded over plastic inner moulded in glass-filled Poly-amide.The seating height can be adjusted with a pneumatic gas-lift having an adjustment stroke of 9.2 ± 0.3 cmThe pedestal is injection moulded in glass-filled Poly-amide and fitted with 5 nos. in wheel castors. The pedestal is 66.0±0.5 cm. pitch centre diameter and 76.0±1.0 cm. with castors. 5 nos. twin wheel castors are injection moulded in Poly-amide having 5.0±0.1cm heel diameter and assembled to the pedestal. The product shall be from one of the approved make of Godrej,Hermanmiller,steel case,delform or vitra only.
8	8 Supplying and placing Almirah of following specifications : Almirah Steel shall have an overall size of916mm(W)x486mm(D)x1980mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. The Almirah Steel should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available.
9	9 Supplying and placing locker of following specificationsOverall size of 4 Door Locker shall be 380mm(W)x450mm(D)x1830mm(H).Stackability shall have add- on units that can be stacked width wise to form bank of lockers having common side panel. Locking shall have 10 Lever cam lock with lock lever plus option of hasp arrangement . Material shall be CRCA 0.6 mm thickness . Construction shall be Rigid Knockdown construction , shelf shall be uniformly distributed load capacity per each shelf level is 35 Kg maximum . Finish shall be epoxy polyester powder coated to the thickness of 50 microns . Handle/Label holder shall be Aesthetically appealing Snap fit ABSplastic handle . Ventilation shall be attractive punched pattern for ventilation .
10	10 Supplying and placing wall storage of following specifications Overall Dimensions of Wall Storage 900 W shall be 900 mmW x 328mm D x 785 mmH . The Construction shall be aesthetically appealing completely knock down construction made from 0.6 mm thk. CRCA as per IS - 513 . Horizontal stiffener shall be made from 1.2 mm thk. CRCA as per IS - 513 . The doors shall be madefrom 18 mm thk. interior grade pre-laminated board as per IS - 12823 or 18 mm thk . Plain particle board as per IS -3087 with 0.6 thk. with 0.6 mmthk. decorative laminate and 0.6 mm thk. backing laminate as per IS - 2046 on either side . All edges shall be duly sealed with 2 mm thk. PVC edge banding . Twodoor withsingle lockon RHdoor . Locking shall be 10 lever cam lock lever at the bottom of the door .Shelving shall be Heightwise adjustable shelf 1 no. Uniformly distributed load capacity of 25 Kg UDL .The finish shall be Epoxy powder coated to the thickness of 50 microns . The doors shall be 448 mm W x 18 mm D x 783 mm H RH side door with lock. 448 mm W x 18 mm D x 783 mm H LH side door w/olock . The doors shall be madefrom 18 mm thk. interior grade pre-laminated board as per IS - 12823 or 18 mm thk . Plain particle board as per IS -3087 with 0.6 thk. with 0.6 mmthk. decorative laminate and 0.6 mm thk. backing laminate as per IS - 2046 on either side . All edges shall be duly sealed with 2 mm thk. PVC edge banding .It shall have two door with single lock on RH door
11	11 Providing and fixing manual chain operated roller blinds consisting of 100% Polyester fabric,fabric thickness 0.50 mm fabric weight = 270 gsm+- 5% , fabric width 230cms, tearing strength 4.5 kgf warp,bursting strength 34 kgf,colour fastness to light 5 to 6 grade in position of standard quantity and approved shade/colour including necessary accessories,MS clamps.screws and drilling etc. as required all complete as per directions of Engineer-In -Charge.(Approved make: Vista/MAC/SD)
12	Electrical Work SH-01 (WIRING AND ACCESSORIES)1 Wiringforlightpoint/fanpoint/exhaustfanpoint/ callbellpoint with1.5 sq.mmFRLS PVC insulated copper conductor single core cable in surface / recessedmediumclassPVCconduit,withmodular switch,modularplate,suitableGIboxandearthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. a Group C
13	2 Wiringforgroupcontrolled(looped)lightpoint/fan point/exhaustfan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. a Group C
14	3 Supply and fixing suitable sizeGI box with modular plateand coverinfrontonsurfaceorinrecess includingprovidingandfixing6pin,15/16Amps modular socket outlet and 15/16 Amps modular switch , connection etc . as required .
15	4 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/recessedmediumclassPVCconduitalong with1No.4sq.mmFRLSPVCinsulatedcopper conductor single core cable for loop earthing as required.
16	5 Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/recessedmediumclassPVCconduit alongwith2Nos.4sq.mmFRLSPVCinsulated copper conductor singlecorecablefor loopearthing as required.
17	6 Wiringforcircuit/submainwiringalongwithearth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit asrequired. a) 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
18	b) 2 X 10 sq. mm + 1 X 6 sq. mm earth wire
19	7 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable inthe existing surface/recessedsteelconduitasrequired a) 3 x 2.5 sq. mm
20	b) 3 x 4 sqmm
21	c) 6 x 4 sq. Mm
22	8 Supplying and fixing modular blanking plate ,on the existing modular plate & switch box excluding modular plate etc. as required.
23	9 Supplying and fixing following modular switch/ socketontheexistingmodularplate&switchbox including connectionsbutexcludingmodularplate etc. as required. a 5/6 A switch
24	b 3 pin 5/6 A socket outlet
25	10 Supplying and fixing following Modular base & coverplateonexistingmodularmetalboxesetc.as required. a 3 Module
26	b 6 Module
27	11 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. a 12 Module (200mmX150mm)
28	SH-02(DISTRIBUTION BOARD)12 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted. a) 6 way (4 + 18), Double door
29	13 Supplyingandfixing5ampsto32amps,rating, 240/415volts,"C"Curve,miniaturecircuitbreaker suitableforinductiveloadoffollowingpolesinthe existing MCB DB complete with connections, testing and commissioning etc. as required. a) Single Pole
30	14 Supplying and fixing folowingrating double pole 240 volts, MCBin the existing MCB DB complete with connections, testing and commissioning etc. as required. a) 63 amp DoublePole MCB
31	15 Supplyingandfixingfollowingratingdoublepole 240volts, Residual current Circuit Breaker ( RCCB ) , having sensitivity of 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. a) 63 amp DP RCCB
32	16 Supplying and fixing 63 amps rating, 240/415 volts, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. a Single pole
33	17Supplying and fixing TPN MCB 63 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required
34	SH-03 LIGHT / FAN FIXTURES) 18 Dismantling the existing worn out / defective fittings from the ceiling andSITC of minimum 36 watt Aluminium slim energy efficient LED Panel light fitting made of CRCA sheet,steel housing duly powder coatedhaving system efficacy minimum 100 lumen/watt LM79, color temp 6500 deg K,symmetric glare free full opal diffuser,IP 20 illumination in the false ceiling, "recess" mounting suitable for fitting in the 600mm x 600mm square existing space having complete with all standard accessories including drivers etc. complete as required.
35	19 SITC of minimum 20 watt Aluminium slim energy efficient LED Panel light fitting made of CRCA sheet,steel housing duly powder coatedhaving system efficacy minimum 100 lumen/watt LM79, color temp 6500 deg K,symmetric glare free full opal diffuser,IP 20 illumination in the false ceiling, "suspended" mounting suitable for fitting in the existing space having complete with all standard accessories including drivers etc. complete as required.
36	20 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.
37	SH-04 (Earthing ) 21 Earthing with copper earth plate 600mm X 600mm X 3mm thick including accessories and providing masonryenclosurewithcoverplatehavinglocking arrangementandwateringpipeof2.7mtrlongetc with charcoal, coke and salt as required.(For computer earthing)
38	22 Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.
39	23 Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.
40	SH - 05 (NETWORKING) 24 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface / recessed steel / PVC Conduit as required. 1 Run of Cable(Make:- Commscope Systimax Only)
41	25 Providing and fixing 24 port loaded Straight patch panel of height 1U in the existing data end rack including making connections, channel labellingetc. complete as required.
42	26 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. a RJ 45 Information Outlet
43	27 Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. a 1 or 2 Module
44	28 Providing and fixing Stranded Low smoke Halogen Cordage Unshielded Cat 6 Modular Patch cord of length 1 mtr with plug insertion life not less than 750 times and minimum Plug Retention force of 133N i/c making connections etc. complete as required.
45	29 Providing and fixing Stranded Low smoke Halogen Cordage Unshielded Cat 6 Modular Patch cord of length 2 mtr with plug insertion life not less than 750 times and minimum Plug Retention force of 133N i/c making connections etc. complete as required.
46	30 SITC of12U Floor Mount Network Rack with accessories (Make:- Rittal / APW / Emerson )
47	31 SITC of 24 Port Non-PoE Managed Access Switchs per specifications in annexure -A as per directions of Engineer in-charge
48	32 5 Years 24x7 Onsite Comprehensive Warranty and Support for24 Port Non-PoE ManagedAccess Switch as per specifications provided and installed under this contract as required. a) For 1st Year
49	b) For 2nd Year
50	c) For 3rd Year
51	d) For 4th Year
52	e) For 5th Year
53	33 Suppling and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess inculding cutting the wall and making good the same in case of recessed condit as required. 25MM PVC Conduit
54	34 Supplying and fixing of UPVC trunking of size 100 x 50 along with accessories on surface complete as required.
55	35 Dismantling & Buy Back of old & defective following items as per required. a 4 x 1 Light fitting.
56	b Ceiling Fans