|
| 1 | Costofdrilling200 mm X 165 mm X 150Mtr M deep bore well in all kinds of soil and rock in rural areas for installation of pump set with hydraulic DTH rig machine, all complete including supplying all material tools drilling rig and air compressor and equipments as well as fuel lubricants and cost of transportation of rig machine and other vehicles up to site including cost of flushing charges, geological investigation etc. all complete as per direction of E/I. 0.00 to 50.00 M |
| 2 | Depth 51.00M - 150.00M |
| 3 | Supplying all tools, tackles & lowering of 200mm dia MS casing pipe including cost of pipe etc. including all taxes, VAT, excise duty, freight charges with inspection charges etc. as aplicable,all complete including carriage to work site. |
| 4 | Supplying all materials labours, tools & equipments for fitting & fixing 200mm dia M.S. cap over casing pipe etc. |
| 5 | CIVIL PORTION Supplying all tools, equipments and labours and lowering 32mm dia G.I. suspension pipes in 3 mtrs. Length in the drilling bore of the tube well etc. all complete job as per direction of E/I. |
| 6 | Providing lobours and equipments forfitting and fixing the deep well cylinderassembly with necessary connecting rods including jointing materials nitrile rubber bucket all tools and plants etc required for the job for low water level all comepete job as per specification and direction of E/I. |
| 7 | Providing all labours & equipments for fitting fixing of deep well hand pump India Mark-II including supplying all tools and plant required for the all job complete as per specification and direction of E/I. |
| 8 | Supplying all materials including cement of approved quality, labours tools for constricting 1.85 m dia. Circular P.C.C. (1:2:4) platformincluding 12 mm thick cementplaster the exposed surface (1:4) with neat cement punningincluding providing necessary shuttering curing and carriage of materials to different tube well sites etc as per UNICEF design and direction of E/I. |
| 9 | Supplying all materials labours and equpments for constructing PCC(1:2:4)drain as per UNICEF design etc all complete |
| 10 | COST OF MATERIALS Supplying extra deep well hand pump complete sets with cylinder assembly& connecting rod (12 Pcs) as per IS : 15500 Part-2/ 2004(Basic Rate) . |
| 11 | Cost of 32mm dia G.I. pipe 3 M. long screwed at both ends with seamless socket as per IS: 1239including all taxes royalty and contractor profit etc |
| 12 | Reducer Cap for Instatlation of Hand Pump |
| 13 | Supplying all materials tools & labours for fitting & fixing control pannel board, 1No. star dealta air beak selector fully automatic with build in single phase prevendor1 No. 3 phase M.C.C. B Suitable with suitable size of copper wire and connectors etc. |
| 14 | Supplying & commissiong of 5 K.V.A Staiblizer (Range 90 V-300V) Three phase with cable, chnge over switch for submersible pump etc. all comp. as per specification and direction of E/I. |
| 15 | E/W in Exavation (as per I.S 3114/1965) for laying of 32mm dia G.I pipes so as 1.0 m av. Cover the socket of pipe ………….. Do ……. etc all comp. as per S/D of E/I. |
| 16 | E/W in back filling in trenches after laying different type & size of pipe with eath remove during excavation within initial lead & lift as per dirction of E/I. |
| 17 | Supplying all tools, labour, euipment for supplying fitting & fixingsubmersible pump set 1.50 H.P single phase with statrer and pannel board according to I.S.I mark etc all comp. job. 150mm dia bonze impellar |
| 18 | Providing fitting & fixing 3 core 2.5 Sqm flate copper cable for Submersible Motor Pump. |
| 19 | Providing & fixing 20mm Nylon rope for Hoisting theSubmersible Motor Pump in Bore well. |
| 20 | Supplying UPVC pipe approved I.S.I make etc as per S/D of E/I. (for Column pipe)(A)32mm dia Column pipe 65M |
| 21 | Supplying all materials ,labours and laying G.I. medium Pipesofapproved make in trenches with red lead and yarn with G.I. socket and screw joints and cutting pipes to sizes and threading ends where necessary etc. all complete as per specification and direction of Engineer-in-Charge a) 32MM Dia |
| 22 | b) 25MM Dia |
| 23 | Supplying and fixing G.I. fitting of approved make all complete as per specification and direction of Engineer-in-charge.(i)32 mm GI Elbow |
| 24 | (ii)32mmreducing socket |
| 25 | (iii)32mm union socket |
| 26 | (v)32mmtee |
| 27 | (ii)25mmreducing socket |
| 28 | (v)25mmtee |
| 29 | (vii)25 mm Jam Nut |
| 30 | 15mm Nipple |
| 31 | 15mm Socket |
| 32 | Providing and fixing of male ended C.I.Body brass spindle valve and seat Bib cock of approved quality with extra socketall complete as per specification and direction of E/I. |
| 33 | Providing & fixing GM non-return valve of approved quality as per specification & direction of E/I. 32 mm dia |
| 34 | Providing and fixing Gun Metal Full way Valves of approved make all complete as per specification and direction of Engineer-in-Charge 32 mm dia G.M. full way Valve weight not less than 1.5 kg |
| 35 | Providing Polyvinyle water storage tank(1000 X 2 NO= 2000) of I.S.I mark (Himgiri/Gangotri) etc with cover and locking arrangement system etc. all comp. job. |
| 36 | Making holes in walls for laying G.I pipes and restoring the same after pipe laying as per specification and direction of E./I 125mm thick |
| 37 | Providing fitting & fixing 2 core 2.5 Sqm copper cable forElectric Connection. |
| 38 | Supplying all materials tools labours and laying ofGI Pipe Tata or Equivalent 32 mm dia (In trench ) |
| 39 | 15 mm dia (on wall) |
| 40 | Supplyingfitting & fixing.GIfittings Fullway valve 32mm |
| 41 | Union Socket 32mm |
| 42 | GI Elbow 32mm |
| 43 | GI Elbow 15mm |
| 44 | GI Tee 32mm |
| 45 | GI Tee 15mm |
| 46 | R/Socket 32mm |
| 47 | Socket 32mm |
| 48 | Socket 15mm |
| 49 | Nipple 15mm |
| 50 | Earth work in excavation in foundation trenchesin hard soil (vide classification of soil item B) and disposal of excavated earth as obtained to a distance up to 50m including all lifts, leveling, ramming the foundation trenches, removing roots of trees, shrubs all complete as per approved design as per building specification and direction of E/I. |
| 51 | Providing coarse clean sand in filling in foundation trenches or in lintin including ramming and watering in layers not exceeding 150mm thicks with all leads and lifts including cost of all materials, labours royalty and taxes all complete as per building specification and direction of E/I. |
| 52 | Providing designation 75Aone brick flat soiling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I. |
| 53 | Providing R.C.C.M - 200 with nominal mix of (1:1.5:3) in foundation and plinth with approved quality of stone chips 20 mm to 6 mm size graded and clean coarse sand of F.M. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing (but excluding the cost of reinforcement) taxes and royalty all complete as per building specification and direction of E/l. |
| 54 | Providing R.C.C.M- 200 with nominal mix (1:1.5:3) in columns with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M.2.5 to 3 including, screening shuttering mixing cement concrete in mixer and placing in position vibrating, striking, curing taxes androyalty all complete as per building specification and direction of E/I |
| 55 | Providing R.C.C.M- 200 with nominal mix (1:1:5:3) in roof slab with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M.2.5 to 3 including, screening shuttering mixing cement concrete in mixer and placing in position vibrating, striking, curing taxes androyalty all complete as per building specification and direction of E/I |
| 56 | Dismantling old plaster and pointing in cement or lime and raking out joints to 15 mm. depth, watering and disposal of unserviceable materials with all leads all complete as per direction of E/l |
| 57 | Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curingwithall leadsand liftsof water, scaffolding taxes and royalty all complete as per building specification and direction of E/l. |
| 58 | Providing and laying 6mm. thick rough grit cheqer tiles in exterior walls of approved texture and colour with 4mm down marble chips of approved shade, size and quality with 100% ordinary cement over 12mm. thick cement plaster (1:3) base, cost of panels and finished with grit wash and rubbed to give granolithic finish including cost of curing, scaffolding, finishing, royalty and taxes all complete as per specification and direction of E/l. |
| 59 | Providing and laying 25mm thick Granite tiles in risers of steps, skirting and pillars of approved size, texture and colour laid over 12mm thick cement mortar (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 60 | Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointed with white cement including rubbing, polishing and cost of curing, taxes and royalty all complete as per building specification and direction of E/l. |
| 61 | Carriage of Materials Sand lead from 20 km |
| 62 | Cement lead from 20 km |
| 63 | Stone chips lead from 20 km |
| 64 | Tor Rod lead from 20 km |
| 65 | Earth work in excavation in foundation trenchesin hard soil (vide classification of soil item B) and disposal of excavated earth as obtained to a distance up to 50m including all lifts, leveling, ramming the foundation trenches, removing roots of trees, shrubs all complete as per approved design as per building specification and direction of E/I. |
| 66 | Providing coarse clean sand in filling in foundation trenches or in lintin including ramming and watering in layers not exceeding 150mm thicks with all leads and lifts including cost of all materials, labours royalty and taxes all complete as per building specification and direction of E/I. |
| 67 | Providing designation 75Aone brick flat soiling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I. |
| 68 | Providing PCC M-100 with nominal mix of (1:3:6) in foundation with approved quality of stone chips 50mm to 25mm size graded and clean coarse sand of F.M. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 69 | Providing 250mm thick brick jail work in C.M. (1:8) in foundation with designation 75A bricks and approved quality of clean coarse sand finished with deep ruled pointing in C.M. (1:3) all complete Jobs as per building specification and direction of E/I. |
| 70 | Providing designation 75A brick work in cement mortar (1:6) in foundation and lintin with approvedquality of clean coarse sand F.M. 2 to 2.5including providing 10mm thick mortar joints, cost of screening materials, racking out joints to 15mm depth curing taxes and royalty all complete as per building specification and direction of E/I. |
| 71 | Providing following materials as Filter Media in the Pit of approved quality and size in layers as per drawing and direction of Engineer in charge all complete job with all taxes and royalty. a) Stone Materials (confirming to M.O.S.T. table no.- 400-7) Grade II (63-45mm) |
| 72 | b) Stone Materials (confirming to M.O.S.T. table no.- 400-7 Grade IV |
| 73 | c) Stone Materials (confirming to M.O.S.T. table no.- 400-7) Doarse sand (F.M greater than 2) |
| 74 | Providing Precast R.C.C. M-150 with nominal mix of (1:2:4) in different place with approved quality of stone chips 20mm to 6mm size graded & clean coarse sand of FM 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer & placing in position vibration, striking, curing (but excluding the cost of reinforcement), taxes and royalty all complete as per building specification and direction of E/I. |
| 75 | Providing for reinforcement as per approved design and drawing including carriage of tor rodto work site including cutting, bending and binding with anncaled wire with cost of wire removal of rust placing the rodsin position all complete as per specification and direction of E/I. |
| 76 | Providing fitting and fixing suitable M.S. grating at inlet of soak pit and cleaning of site for execution of work as per direction of E/I. |
| 77 | Supplying materials and construction of brick masonry drain 150mm width and 150mm depth with 250mm apron on both sides over 50mm thick P.C.C (1:3:6) over a brick flat soling, apron laying, brick work in C.M (1:6), 12mm C.P (1:3) with punning on exposed surface all complete as per specification and direction of E/I. |
| 78 | Supplying materials, labours and equipments for construction of 1.20M x0.90M size P.C.C (1:2:4) Rectangular Platform around stand post including 12mm thick cement plaster in C.M (1:4) with neat cement punning over exposed surface all complete job as per approved design, specification and direction of E/I. |
| 79 | Carriage of Materials Sand lead from 20 km |
| 80 | Cement lead from 20 km |
| 81 | Brick lead from 20 km |
| 82 | Stone chips lead from 20 km |
| 83 | Tor Rod lead from 20 km |
| 84 | 18% GST |
| 85 | Labour cess |
