Tender For Construction Of New Su Swasthya Kendra Big Health And Wellness Centre At Chhoto Mechia Basti Within Jaigaon I Gp Under Kalchini Block
Tender Value
42.24 Lakhs
Estimated cost
Bid Submission
13 Feb 2023
0 days left
EMD
84500
Bank guarantee accepted
Document Fee
4200
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
kalchini → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of New Su Swasthya Kendra Big Health And Wellness Centre At Chhoto Mechia Basti Within Jaigaon I Gp Under Kalchini Block
BOQ
| Sl. No. | Item Description |
| 1 | Surface dressing of the ground…. |
| 2 | Earth work in excavation of foundation tranches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailling out water as required complete.(depth not exceeding 1.50 m) |
| 3 | Earth work in filling in foundation trenches or plinthwith good earth, in layers not exceeding 150 mm.including watering and ramming etc. layer by layercomplete. (Payment to be made on the basis ofmeasurement of finished quantity of work)(a) With earth obtained from excavation of foundation |
| 4 | Filling in foundation or plinth by silver sand……… |
| 5 | supplying and laying polythene sheet…. |
| 6 | 25mm thick damp proof course with cement concrete with stone chips (1:1.5:3)…….. |
| 7 | Single Brick flat soling of picked jhama bricks incluiding ramming and dressing bed to proper level |
| 8 | Cement concrete with graded stone ballast (40 mm size excluding shuttering) In ground floor (1:3:6)(A) [Pakur Variety] |
| 9 | Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size)Pakur variety |
| 10 | Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) Pakur varietyIn ground Floor & foundation |
| 11 | Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) Pakur varietyIn first Floor |
| 12 | Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) Pakur varietyIn 2nd Floor |
| 13 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction.In ground Floor & foundation |
| 14 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction.In first Floor |
| 15 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction.In 2nd Floor |
| 16 | Hire and labour charges for shuttering with centreing and necessary staging ……….. Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete workIn ground Floor & foundation |
| 17 | Hire and labour charges for shuttering with centreing and necessary staging ……….. Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete workIn first Floor |
| 18 | Hire and labour charges for shuttering with centreing and necessary staging ……….. Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete workIn 2nd Floor |
| 19 | Brick work with 1st class bricks in cement mortar (1:6) In Foundation & Plinth |
| 20 | Brick work with 1st class bricks in cement mortar (1:6) In superstructure, ground Floor |
| 21 | Brick work with 1st class bricks in cement mortar (1:6) In first Floor |
| 22 | Brick work with 1st class bricks in cement mortar (1:6) In 2nd Floor |
| 23 | 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor. |
| 24 | 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) In first Floor |
| 25 | 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) In 2nd Floor |
| 26 | Labour for Chipping of concrete surface before taking upPlastering work. |
| 27 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (a) 20 mm thick plaster (6:1) in ground floor. |
| 28 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (a) 20 mm thick plaster (6:1)In first Floor |
| 29 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (a) 20 mm thick plaster (6:1)In 2nd Floor |
| 30 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (b) 15 mm thick plaster (6:1) in ground floor. |
| 31 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (b) 15mm thick plaster (6:1)In first Floor |
| 32 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (b) 15mm thick plaster (6:1)In 2nd Floor |
| 33 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (c) 10 mm thick plaster (4:1) in ground floor. |
| 34 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (c) 10 mm thick plaster (4:1) In first Floor |
| 35 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (c) 10 mm thick plaster (4:1) In 2nd Floor |
| 36 | Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc. |
| 37 | Artificial stone in floor, dado, staircase etc with cementconcrete (1:2:4) with stone chips, laid in panels as directedwith topping made with ordinary or white cement (asnecessary) and marble dust in proportion (1:2) includingsmooth finishing and rounding off corners including rakingout joints or roughening of concrete surface and applicationof cement slurry before flooring works using cement @ 1.75kg/sq.m all complete including all materials and labour. 25mm thick |
| 38 | Extra cost of labour over grey artificial stone for (i) Chequering |
| 39 | Supplying and laying true to line and level vitrified tiles ofapproved brand (size not less than 600 mm X 600 mm X 10mm thick)…… (I) With application slurry @1.75 kg/ Sq.m, 20 mm sand cement mortar (1:4) & 2 mm thick cement slurry at back side of tiles, 0.2 kg/ Sq.m white cement for joint filling withpigment. (B) Light Colour |
| 40 | 18 mm. to 22 mm. thick, kota stone slab set in 20 mm thick(avg) cement mortar (1:4) in floor, stair & lobby includingpointing in cement slurry with admixture of pigment matchingthe stone shade, including grinding & polishing as perdirection of Engineer - in - charge to match with the existingwork. [Slurry for bedding @ 4.4 kg/Sq.m and pointing @2.0kg/Sq.m] |
| 41 | Supplying, fitting & fixing 1st quality Ceramic tiles in wallsand floors to match with the existing work & 4 nos. of keystones (10mm) fixed with araldite at the back of each tile &finishing the joints with white cement mixed with colouringoxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by syntheticadhesive & grout materials etc. (A) Floor (a) Area of each tile upto 0.09 Sq.m (i) Coloured decorative |
| 42 | Supplying, fitting & fixing 1st quality Ceramic tiles in wallsand floors to match with the existing work & 4 nos. of keystones (10mm) fixed with araldite at the back of each tile &finishing the joints with white cement mixed with colouringoxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by syntheticadhesive & grout materials etc. (B) Wall(a) Area of each tile upto 0.09 Sq.m (i) Coloured decorative |
| 43 | Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick) In ground floor |
| 44 | Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick) In 1st floor |
| 45 | Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick) In 2nd floor |
| 46 | Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturer\"s specification) including cleaning and smoothning of surface.Two Coats In ground floor |
| 47 | Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer\"s specification and as per direction of the EIC.Two Coats In ground floor |
| 48 | Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer\"s specification and as per direction of the EIC.Two Coats In 1st floor |
| 49 | Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer\"s specification and as per direction of the EIC.Two Coats In 2nd floor |
| 50 | Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer\"s specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. c) Super Protective 100% Acrylic Emulsion.Two Coats In ground floor |
| 51 | Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer\"s specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. c) Super Protective 100% Acrylic Emulsion.Two Coats In 1st floor |
| 52 | Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer\"s specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. c) Super Protective 100% Acrylic Emulsion.Two Coats In 2nd floor |
| 53 | Supplying fitting and fixing in position approved P.V.C. door frame (Matt finish) made of extruded P.V.C. multichamber hollow section having dimensions 60mm x 50mm x 2mm (+/-0.2mm), horizontal section will be joined with vertical section by galvanised steel screws after inserting two number steel brackets as reinforcement making suitable space for placing hinges, one steel tube 40mm x 20mm x 1.20 mm will be inserted on one full vertical side of the frame (hinge side) as reinforcement, the frame will then be fixed in the opening with the help of P.V.C. expandable fastner/wooden gutties and galvanised steel screws including cost of all materials and labour, hire charges of tools and appliances, carriage of all materials, taxes and all other incidental charges complete. |
| 54 | PVC 26 Door Shutter-37 mm thick:Supplying fitting and fixing P.V.C. door shutter of approved quality & shade in position, the style & rail of the P.V.C. door shutter will be made of rigid P.V.C. multicavity hollow chamber of suitable size and section with 2.0 mm (+/-0.2 mm) wall thickness, .................. The rate is inclusive of cost of all materials, labour, and hire of tools and plants and appliencies. Carriage of all materials taxes and all other incidental charges complete.The rate is exclusive of cost of hinges, hasp bolt, tower bolt,door ring etc.In ground floor. |
| 55 | PVC 26 Door Shutter-37 mm thick:Supplying fitting and fixing P.V.C. door shutter of approved quality & shade in position, the style & rail of the P.V.C. door shutter will be made of rigid P.V.C. multicavity hollow chamber of suitable size and section with 2.0 mm (+/-0.2 mm) wall thickness, .................. The rate is inclusive of cost of all materials, labour, and hire of tools and plants and appliencies. Carriage of all materials taxes and all other incidental charges complete.The rate is exclusive of cost of hinges, hasp bolt, tower bolt,door ring etc.In 1st floor. |
| 56 | Collapsible gate with 40mm x 40mm x 6mm Tee as top and bottom guide rail, 20mm x 10mm x 2mm vertical channels 100mm apart in fully stretched position 20mm x 5mm M.S. flats as collapsible bracings properly rivetted and washered including 38mm steel rollers including locking arrangements, fitted and fixed in position with lugs set in cement concrete and including cutting necessary holes, chasing etc. in walls, floors etc. and making good damages complete |
| 57 | M.S. gate of Jail type as per approved design made of strong M.S. frame work, intermediate stiffeners and round / square bars or angles. M.S. sheet (not less than 14 gauge) gussets, cleats etc. including necessary riveting, bolting, welding, locking and hanging arrangements, fitting and fixing complete as per direction of the Engineer-in -charge. |
| 58 | M.S.or W.I. Ornamental grill of approved design jointscontinuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor.Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr.In ground floor |
| 59 | M.S.or W.I. Ornamental grill of approved design jointscontinuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor.Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr.In 1st floor |
| 60 | Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc |
| 61 | Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : (b) On steel or other metal surface Two coats (with any shade except white) |
| 62 | Supplying,fitting & fixing of 2-Track / 3-Track Aluminium sliding Window of all Aluminium sections viz. window frame (top,bottom & side frame), shutter (top, bottom, side & interlock member) made of aluminium alloy extrusions conforming to IS 733-1983 & IS 1285-1975, annodised conforming to IS 1868-1983, fitted with all other accessories viz. PVC roller, EPDM gasket, maruti lock, screws etc. including labour charges for fitting & fixing of aluminium 2-track/3-track sliding window with fixing of glass (excluding cost of glass) all complete as per architectural drawings and direction of Engineer-in-charge.10-12 Micron thickness Annodizing filmNatural white |
| 63 | Supplying, fitting & fixing of partly glazed partly panelled or fully glazed single leaf Aluminium swing door of all aluminium sections viz door frame ( top and side frame), shutter( top rail, bottom rail, lock rail, door vertical) , glazing clip made of Aluminium Alloy Extrusions conforming to IS: 733-1983 and IS: 1285-1975, annodized conforming to IS:1868- 1983, fitted with all other accessories viz. EPDM gusket,cleat, angle screws etc. including labour charges for fitting and fixing of aluminium door with door spring,/aluminium hinges, glass / Panel board all complete as per architectural drawings and direction of Engineer-incharge. |
| 64 | Supplying profiles of required section made of Aluminium Alloy Extrusions conforming to IS: 732-1983 and IS: 1285- 1975; Annodized (with required film thickness and specified colour / natural) matt finished conforming to IS: 1868-1983 for fabrication of composit door, sliding & casement windows, partitions, formed of basic sections of any ISI embossed / certified make and brand as per direction of Engineer - In- Charge. In 10-12 Micron thickness Annodizing film I) Natural white h) Louvered window Top, bottom and side member |
| 65 | Louvered Section. |
| 66 | Cleat angle ( Non-annodized). |
| 67 | Fixed glazing. Top, bottom and side member. |
| 68 | Mullion. |
| 69 | Glazing clip. |
| 70 | Anodised aluminium butt hinges of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 205/66) and fitted and fixed with cadmium plated screws: 100 x 75 x 4.0mm. |
| 71 | Supplying 4 lever mortice lock or any approved make and brand as per direction of the Engineer- in -Charge. ii) 100 mm. |
| 72 | Labour charge for fabrication and installation of composite door, window, partitions made from annodized extruded alloy aluminium sections iv ) Fixed glazing. |
| 73 | Louvered window. |
| 74 | Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987. 4mm thick clear glass. |
| 75 | 8mm thick coloured / tinted / smoke glass |
| 76 | Providing, fitting and fixing in position, medium density fibre board conforming to IS: 12406-1988 for plain and IS: 14587-1998 for prelaminated made of wood fibre bonded with Urea formaldehyde for interior grade and Phenol Formaldehyde for exterior grade conforming to per IS:848-1974 as per approved make and brand as per direction of Engineer-in-Charge. Both side decorative lamination, Interior Grade (ii) 12mmIn Ground Floor |
| 77 | Both side decorative lamination, Interior Grade (ii) 12mm1st Floor |
| 78 | Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete: (a) With continuous plate base (Hexagonal/ Round rod) (iv) 125 mm grip x 10 mm dia rod. |
| 79 | Anodised aluminium barrel / tower / socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated screws:225mm long x 10mm dia. bolt. |
| 80 | 150mm long x 10mm dia. bolt. |
| 81 | Iron hasp bolt of approved quality fitted and fixed complete (oxidised) with 16mm dia rod with centre bolt and round fitting (b) 250mm long. |
| 82 | Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concrete structures etc if necessary and mending good damages including joining with jointing materails (Spun Yarn, Valamoid/Bitumen/M-Seal etc) complete UPVC Pipes (ii) 110 mm. Dia. |
| 83 | Plain Tee (ii) 110 mm. Dia. |
| 84 | Plain Y (ii) 110 mm. Dia. |
| 85 | Bend 87.5 degree(ii) 110 mm. Dia. |
| 86 | Shoe(ii) 110 mm. Dia. |
| 87 | Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately)For Exposed Work, 40 mm PVC pipe |
| 88 | For Concealed Work, 15 mm PVC pipe |
| 89 | For Concealed Work, 20 mm PVC pipe |
| 90 | For Concealed Work, 25 mm PVC pipe |
| 91 | Supplying, fitting and fixing Peet\"s valve fullway gunmetal standard pattern best quality of approved brand bearing I.S.I. marking with fittings (tested to 21 kg per sq. cm.). 15 mm dia |
| 92 | 20 mm dia |
| 93 | 25 mm dia |
| 94 | Supplying, fitting and fixing bib cock or stop cock.Chromium plated Bib Cock short body (Equivalent to Code No. 511 & Model - Tropical / Sumthing Special of ESSCO or similar brand). |
| 95 | Chromium plated angular Stop Cock with wall flange (Equivalent to Code No. 5053 & Model - Florentine of Jaquar or similar brand). |
| 96 | Supplying P.V.C. water storage tank of approved quality with closed top with lid (Black) - Multilayer 1500 litre capacity |
| 97 | Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc. |
| 98 | Labour for punching hole in plastic water storage tank upto 50 mm dia |
| 99 | labour for hoisting plaster strage tank………… |
| 100 | labour for hoisting plaster strage tank……………….. |
| 101 | washing basin vitreouschina of approved make ……………….. |
| 102 | Supplying, fitting and fixing white vitreous china best quality approved make wash basin with C.I. brackets on 75 mm X 75 mm wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillar cock of 15 mm dia., C.P. chain with rubber plug of 30 mm dia., approvedquality P.V.C. waste pipe with C.P. nut 32 mm dia., 900 mm long approved quality P.V.C. connection pipe with heavy brass C.P. nut including mending good all damages and painting the brackets with two coats of approved paint.550 mm X 400 mm size |
| 103 | Supplying,fitting and fixing approved brand 32 mm dia.P.V.C. waste pipe, with PVC coupling at one end fitted with necessary clamps900 mm long |
| 104 | Supplying, fitting and fixing 15 mm swan neck tap with left & right hand operating nob with aerator (Equivalent to Code No. 510, 510(A) and Model - TROPICAL / SUMTHING SPECIAL of ESSCO or similar brand) |
| 105 | Supplying, fitting and fixing 15 mm swan neck tap with left & right hand operating nob with aerator |
| 106 | CP Pillar Cock - 15 mm. (Equivalent to Code No. 507 & Model -Tropical / Sumthing Special of ESSCO or similar brand). |
| 107 | Supplying, fitting and fixing C.I round gradting 1 100mm |
| 108 | Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992 (i) Single Socketed 3 Meter Length (b) 110 mm |
| 109 | Labour for fitting and fixing U.P.V.C. pipes for above ground work including cost of jointing materials etc. fitting and fixing all necessary specials, cutting pipes, cutting holes in walls or R.C. floor where necessary ......... as per direction of the Engineerin-charge. (Payment will be made on centre line measurement of the total pipeline including specials.A) Above ground (ii) 110 mm dia |
| 110 | (B) Under ground (ii) 110 mm dia |
| 111 | Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992 viii) Double Y with Door (b) 110 mm |
| 112 | Door Bend (T.S.) (b) 110 mm |
| 113 | Vent Cowl (b) 110 mm |
| 114 | Pipe Clip (b) 110 mm |
| 115 | Plain Tee (b) 110 mm |
| 116 | Plain Tee (b) 110 mm |
| 117 | Supplying, fitting and fixing E.W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc (a) With \"P\" trap |
| 118 | Supplying, fitting and fixing Squating plate with integral flushing in white vitreous chinaware of approved make in cement concrete (6:3:1) with jhama chips complete. (Payment of concrete will be paid seperately). (i) 450 mm X 350 mm |
| 119 | Supplying, fitting and fixing Closet seat of approved make with lid and C.P. hinges, rubber buffer and brass screws complete. (a) E.W.C.(ii) Plastic (hallow type) white |
| 120 | Supplying,fitting and fixing 32 mm dia. Flush Pipe of approved make with necessary fixing materials and clamps complete. i) Polythene Flush Pipe |
| 121 | Supplying, fitting and fixing liquid soap container. (c) Fibre glass |
| 122 | Supplying, fitting and fixing best quality Indian make mirror 5.5 mm thick with silvering as per I.S.I. specifications supported on fibre glass frame of any colour, frame size 550 mm X 400 mm |
| 123 | Supplying, fitting and fixing towel rail with two brackets.(a) C.P. over brass (i) 25 mm dia. and 450 mm long |
| 124 | Constructing Inspection pit of inside measurement 600mm X 600mm X upto 600mm (depth) with 250 mm thick 1st. class brick work in cement mortar (1:4) on all sides,…….. i) With Pakur variety. (SAIL/TATA/RINL) |
| 125 | Construction of circular soak well 2.5 metre deep in all types of sandy soils with dry brick work upto 1.6 metre from the bottom having 150 mm intermediate cement brickwork (1:4) band all round and cement brick work (1:4) upto 0.90 metre from top with 20mm thick cement plastering (1:4)............With 250 mm thick dry brick work and 250 mm thick cement brick work (1:6) and 1.00m inside dia.(SAIL/TATA/RINL) |
| 126 | Construction of septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar (1:4) including two 560 mm dia. R.C.C. manhole cover(heavy type)of approved make supplied, fitted and fixed in the 100mm thick R.C.C (1:1.5:3) top slab with necessary fittings (ii) For 20 users A) With Pakur variety. (SAIL/TATA/RINL) |
| 127 | Cement concrete with graded stone ballast (40 mm size excluding shuttering) In ground floor (1:3:6)…………. |
| 128 | supply fitting and fixing in position C.I manhole / pit cover with rim . (sqr III 600mmx 600mm x32kg … |
| 129 | Supplying and delivery at site submersible pump set including ………….. Etc complete |
| 130 | Fishing the end of folowing p.v.c armourted cable ………………. Materials |
| 131 | Supplying and laying 1 kv gradepvc/a cable ……………….. Rubbish |
| 132 | supplying and fixing compression type gland complete with brass gland complete ……………….. Below |
| 133 | Finishing the end of following PVC armart cable by crimping ………………. Materials |
| 134 | Supplying and fixing C.l water propf looping calbebox ………………………….muffing |
| 135 | Supplying and delivery 1.1 kv grade 3 core ……………………make |
| 136 | Labour for boring tube well of require dia……………………………40 mm dia |
| 137 | Labour for boring tube well of require dia……………………………80 mm dia |
| 138 | Supplying fitting and fixingplug of ……………………………Specifications |
| 139 | Supplying fitting and fixingsteel cutter make ………………………Specificatons |
| 140 | Supply of G.I pipes of TATA make including ………….. |
| 141 | Supplying PVC strainer of approved ……………….Specificatios |
| 142 | Supply of PVC pipes & fittings schedule ……………..25mm |
| 143 | Supply of PVC pipes & fittings schedule ……………..32mm |
| 144 | Supply of PVC pipes & fittings schedule ……………..40mm |
| 145 | Supply of PVC pipes & fittings schedule ……………..80mm |
| 146 | Labour for fitting and fixing high density poly - ethylene pipes ……………..25 mm necessary |
| 147 | Labour for fitting and fixing high density poly - ethylene pipes ……………..32 mm |
| 148 | Labour for fitting and fixing high density poly - ethylene pipes ……………..40mm |
| 149 | Labour for fitting and fixing high density poly - ethylene pipes ……………..80mm |
| 150 | Supplying , fitting and fixing gunmetal ………………………………….25 mm dia |
| 151 | Supplying , fitting and fixing gunmetali) 50mm x 100 mm |
| 152 | Supplying of galvanised iron socket ………………40 mm |
| 153 | Supply of G.I bend ……………….40 mm |
| 154 | Supply of G.I plainequal elbow ……………….40 mm |
| 155 | Supply of G.I plain tee……………….40 mm |
| 156 | Supply of G.I nipple standerd 50mm ……………….40 mm |
| 157 | Supply of G.I union……………….40 mm |
| 158 | Supply of G.I short piece of TATAmake …………….40 mm |
| 159 | Washing and development tubewell with air compressor ……………………..plants |
| 160 | Labour for making arrange ment for ……………etc |
| 161 | Collecting sample of water for bacteriological at any………………..respect |
| 162 | Geophysical investigation of the acquifer…………………. Including |
| 163 | Cement concrete with graded stone …………………. |
| 164 | Hire and labour charges for shuttering with …………….thick |
| 165 | 125 mm thick brick work with 1st class…………….floor |
| 166 | Plaster (to wall , floor, cellingetc) with sand ……………necessary |
| 167 | Neat cement punning about 1.5mm thick in wall, dado, window sill, floor |
| 168 | Distn. wiring in 22/0.3 (1.5 sqmm) single core stranded \"FR\"PVC insulated & unsheathed single core stranded copper wire (Brand approved by EIC) in 19 mm bore, 3 mm thick polythen pipe complete with all accessories embedded in wall to light/fan/call bell points with Piano key type switch (Anchor make) fixed on sheet metal (16 SWG) switch board with bakelite/perspex (wall matching colour) top cover (3 mm thick) flushed in wall incl. mending good damages to original finish 2x22/0.3 (Ph. & N) and 1x22/0.3 as ECC, Average run 6 mtr |
| 169 | Distribution wiring in 1.1 KV grade 2x22/0.3 (1.5 sqmm) single core stranded \"FR\" PVC insulated & unsheathed copper wire(Brand approved by EIC) in suitable size PVC casing-capping(Precision make) with 1x22/0.3 (1.5 sqmm) single corestranded \"FR\" PVC insulated & unsheathed copper wire forECC, incl. necy. PVC clips, fittings etc. to light point with 2 no.2 way piano key type switch fixed on sheet steel fabricatedswitch board with Perspex/bakelite top cover on wall incl.necy. connections and making earthing attachment andmending good damages to building works. [PVC casingcapping and Switch board both on surface] Average run7mtr |
| 170 | Distribution wiring in 1.1 KV grade 2x22/0.3 (1.5 sqmm) single core stranded \"FR\" PVC insulated & unsheathed copper wire(Brand approved by EIC) in suitable size PVC casing-capping(Precision make) with 1x22/0.3 (1.5 sqmm) single corestranded \"FR\" PVC insulated & unsheathed copper wire forECC, incl. necy. PVC clips, fittings etc. to light point with 2 no.2 way piano key type switch fixed on sheet steel fabricatedswitch board with Perspex/bakelite top cover on wall incl.necy. connections and making earthing attachment andmending good damages to building works. [PVC casingcapping and Switch board both on surface] Average run 8 mtr |
| 171 | Distribution wiring in 1.1 KV grade 2x22/0.3 (1.5 sqmm) single core stranded \"FR\" PVC insulated & unsheathed copper wire(Brand approved by EIC) in suitable size PVC casing-capping(Precision make) with 1x22/0.3 (1.5 sqmm) single corestranded \"FR\" PVC insulated & unsheathed copper wire forECC, incl. necy. PVC clips, fittings etc. to light point with 2 no.2 way piano key type switch fixed on sheet steel fabricated |
| 172 | Supplying and Drawing 1.1 KV single core stranded \"FR\"PVC insulated & unsheathed single core stranded copper wire (Brand approved by EIC) of the following sizes in the prelaid polythene pipe and by the prelaid GI fish wire and making necy. connection as required2 x 22/0.3 (1.5 sqmm) +1x22/0.3 (1.5 sqmm) as ECC (Separate 6A plug point) |
| 173 | 2x36/0.3 (2.5 sqmm) + 1x22/0.3 (1.5 sqmm) as ECC (Separate 20A plug point) |
| 174 | 2x84/0.3 (6 sqmm) + 1x56/0.3 (4 sqmm) as ECC (Sub main wiring & UPS) |
| 175 | 2x84/0.3 (6 sqmm) + 1x56/0.3 (4 sqmm) as ECC (Sub main wiring & UPS) |
| 176 | Supplying and fixing polythene pipe complete with fittings as necy. under ceiling/beam, bound with 22 SWG GI binding wire incl. supplying and drawing 1x18 SWG GI Wire as fish wire inside the pipes and fittings and providing 50 mm dia disc of MS sheet (20 SWG) having colour paint at one face fastened at the load point end of the polythene pipe with fish wire (synchronizing with roof/beam casting work of building construction) 19mm dia 3mm thick Polythene Pipe |
| 177 | 25mm dia 3mm thick Polythene Pipe |
| 178 | Cutting channel of 40 mm x 40 mm size on masonry wall incl.S&F heavy gauge polythene pipe dia as stated below, bymeans of iron hooks and supplying and drawing 18 SWG GIWire as fish wire incl. mending good damages to buildingworks19 mm dia 3 mm thick polythene pipe without earthcontinuity wire |
| 179 | Finishing of the PVC insulated wire ends by socketting with pin/ ring type copper sockets and insulated tapes etc., including supplying sockets, tapes. 2.5sqmm |
| 180 | 4 sqmm |
| 181 | 6 sqmm |
| 182 | Distn. wiring in 22/0.3 (1.5 sqmm) single core stranded \"FR\"PVC insulated & unsheathed single core stranded copper wire (Brand approved by EIC) in 19 mm bore, 3 mm thick polythen pipe complete with all accessories embedded in wall to 240 V 5A 3 pin plug point incl. S&F 240 V 5A 3 pin flush type plug socket & piano key type switch (Anchor make) incl. S&F earth continuity wire, fixed on sheet metal (16 SWG) switch board with bakelite/perspex (wall matching colour) top cover (3 mm thick) flushed in wall incl. mending good damages to original finish2x22/0.3 (Ph. & N) and 1x22/0.3 as ECCOn Board |
| 183 | Distn. wiring in 22/0.3 (1.5 sqmm) single core stranded \"FR\"PVC insulated & unsheathed single core stranded copper wire (Brand approved by EIC) in 19 mm bore, 3 mm thick polythen pipe complete with all accessories embedded in wall to 240 V 5A 3 pin plug point incl. S&F 240 V 5A 3 pin flush type plug socket & piano key type switch (Anchor make) incl. S&F earth continuity wire, fixed on sheet metal (16 SWG) switch |
| 184 | Supply & Fixing 240 V, 6A, plug socket with separate 6 APiano key type switch (Brand approved by EIC) on sheetmetal switch board embedded in wall incl. S & F 150x100x65mm MS (16SWG) switch |
| 185 | Supply & Fixing 240 V, 6A, plug socket with separate 6 APiano key type switch (Brand approved by EIC) on sheetmetal switch board embedded in wall incl. S & F 150x100x65mm MS (16SWG) switch board and bakelite/perspex top cover of 3mm thick by Brass screws after making housing for switch by cutting bakelite/perspex cover and making necessary connections as required. |
| 186 | Supply & Fixing 240 V, 20A, plug socket with separate 20 APiano key type switch (Brand approved by EIC) on sheetmetal switch board embedded in wall incl. S & F150x100x65mm MS (16SWG) switch board and bakelite/perspex top cover of 3mm thick by Brass screws after making housing for switch by cutting bakelite/perspex cover and making necessary connections as required(Separate 20A Switch Board) |
| 187 | Supply & Fixing 240 V, 4 nos. 6A, plug socket with separate 4nos. 6 A Piano key type switch, indicator & 16A switch typeSP MCB (Brand approved by EIC) on sheet metal switchboard embedded in wall incl. S & F 240x200x65mm MS(16SWG) switch board and bakelite/perspex top cover of3mm thick by Brass screws after making housing for switch by cutting bakelite/perspex cover and making necessaryconnections as required (CPU Board) |
| 188 | Supply & Fixing 240 V, 25A, 3 PIN modular typeplug socketwith …………………….etc |
| 189 | Supply & Fixing 240 V,25 A, 3 pin Modular type plug topwith indicator (Brand approved by EIC) & necy. Connections (UPS Board). |
| 190 | Supplying and fixing Sheet steel Main Switches on angle iron frame on wall32A DP (Standard/HPL Make) |
| 191 | Supplying & fixing sheet metal (16 SWG) Iron Clad Busbar chambers on angle iron frame on wall, incl. earthing attachment and painting as required – (As per Drawing no. 470 of PWD Specification Book – May 1991)2 bars 240 V, 63 A |
| 192 | Supplying and fixing Changeover switch with Sheet Steel enclosure on flat iron frame on wall with nuts bolts etc32A, 240V DP (Standard/HPL Make) |
| 193 | Supplying and fixing double-door SPN MCB DistributionBoard with IP-42/43 protection, concealed in wall after cutting the wall & mending good the damages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthing attachment.2+4 way (EDB 1) (607710) |
| 194 | 2+8 way (Ground & 1st floor, NDB 2&3) (607711) |
| 195 | 2+12 way (Ground & 1st floor, NDB 2&3) (607712) |
| 196 | Supplying and fixing MCB SS enclosure with IP-20/30protection, powder coated provision for two/four poleMCB, concealed in wall after cutting the wall & mendinggood the damages to original finish incl. painting,connection & provision for earthing attachment2 Way (UPS DB) |
| 197 | 4 Way (NDB-1) |
| 198 | Supplying and fixing 240/415 V MCB of Breaking capacity 10kA & C characteristics on din rail of existing DBs and necessary connection Single pole 6-32 A MCB (SPNDB Outing) |
| 199 | Single pole 25A MCB (EDB1 Outing) |
| 200 | Double pole 32A MCB (EDB1, NDB 2-3) |
| 201 | Double pole 32A MCB (UPS) |
| 202 | Double pole 25A MCB (EDB 2-3, Incomer) |
| 203 | Double pole 32A MCB (NDB 1-4way) |
| 204 | Supply & Fixing Socket type fan regulator (Step type) (Brand approved by EIC) on existing sheet metal switch board with bakelite/perspex top cover by screw after making housing for regulator knob by cutting bakelite/perspex top cover incl. making necy. connections etc. |
| 205 | Supplying & Fixing of Box type fan clamp of 150mm dia & 80mm depth made of 16 SWG CRCA sheet with one end duly sealed by cover, properly welded, incl. S&F 12mm dia 600mm long MS rod duly bent by heat treatment at the centre position of rod to grip fan bobbin properly, incl. binding the rod and fan box with reinforcement by 22 SWG steel binding wire, incl. supplying & covering the box with alkathene sheet, placed in order to prevent concrete from entering the box |
| 206 | Fixing only ceiling fan complete with blades, canopy, fork, rubber bush etc. incl. S&F connecting wire for down rod upto 30 cm incl. painting the rod with approved paint and making necessary connection as required by 2x1.5 sqmm flexible copper wire. |
| 207 | Fixing only exhaust fan after making hole in wall and making good damages and smooth cement finish etc. as practicable as possible and providing necy. length of PVC insulated wire and making connection for exhaust of following diameter:30 cm (12\") |
| 208 | Supply & Fixing louver shutter on wall with necy. bolts & nuts (6 mm dia x 62 mm long) For Al: 30 cm Exhaust fan (12\") |
| 209 | Supplying & Fixing 240 V AC Buzzer (Ancho) on HW board incl. S&F HW board |
| 210 | Supplying & Fixing 240 V AC Buzzer (Ancho) on HW board inc |
| 211 | Supply & Delivery of Sweep-48\" (1200 mm) AC Ceiling fan…… |
| 212 | Supply & Delivery of Sweep-48\" (1200 mm) AC |
| 213 | Supply & Delivery of Sweep-12\" (300 mm) Sweep heavy duty…… Exhaust fan |
| 214 | Supply & Delivery of Sweep-12\" (300 mm) Sweep heavy duty…… Exha |
| 215 | Supply of 1.1 KV grade PVC insulated conductor……… 25 sqmm 2 core |
| 216 | Laying of cable upto 2 core 25 sqmm on wall/surface incl. S & F MS saddles with earthing attachment in 10 SWG GI (Hot Dip) Wire, making holes etc. as necy. mending good damages and painting |
| 217 | Supplying and fixing compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture-proof entry of XLPE/PVC armoured cables as below : For 2 core upto 25 sqmm |
| 218 | Finishing the end of following XLPE/PVC armoured cables bycrimping method incl. supplying and fixing solderless socket(Dowels make), tapes, anticorrosive paste & jointing materials 2 core 25 sqmm cable |
| 219 | Excavation of soil for installation of Earth Electrode and filling & ramming. For Morrum Soil |
| 220 | Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm diax 80 mm long GI bolts, double nuts, double washers incl. S &F 15 mm dia GI pipe protection (1 Mts. long) to be filled withbitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level as below: By TATA-Medium GI pipe |
| 221 | Extra for providing masonery enclosure on the top of the earth electrode of overall size 86.36 cm x 86.36 cm x 46 cm deep (below Ground level) complete with cemented brick work(1:6) of 25 cm width duly plastered with cement morter (inside) CI hinged inspection cover of size 36.56 cm x 35.56 cm with locking arrangement, GI reducer including drilling of 46 nos. 12 mm dia holes on the GI pipe |
| 222 | Supplying & fixing earth busbar of galvanized (Hot Dip) MS flat 25 mm x 6 mm on wall having clearance of 6 mm from wall including providing drilled holes on the busbar complete with GI bolts, nuts, washers, spacing insulators etc. as required |
| 223 | Connecting the equipments body to earth busbar includingS&F 20 mm x 3 mm galvanised (Hot Dip) MS flat on wall/floorwith GI saddles as required and connection to equipments incl. drilling holes, with bolts, nuts, washers etc. |
| 224 | Connecting the equipments to earth busbar including S & F GI (Hot Dip) wire of size as below on wall/floor with staples buried inside wall/floor as required and making connection to equipments with bolts, nuts, washers, cable lugs etc. asrequired and mending good damages Solid GI wire, No. 8 SWG |
| 225 | Supply & Fixing RJ45 sitable for CAT6 cable (Brand approved by EIC) with PVC board and top cover plate on wall and making necessary connections & testing as required |
| 226 | Supply & Fixing Telephone socket (RJ11) Modular type(Brand approved by EIC) with PVC board and top coverplate on wall and making necessary connections &testing as required |
| 227 | Supplying & Drawing 2-pair Telephone cables with highdensity polyethylene insulated solid annealed high conductivity bare copper of dia 0.5mm in prelaid PVC rigid conduit/ in polythene pipe embeded in wall. |
| 228 | Supplying & Drawing LAN cable (CAT6) (Brand approved byEIC) in prelaid PVC rigid conduit/ in polythene pipe embededin wall. |
| 229 | Supplying and fixing PVC casing-capping [Precision Make] onwall or ceiling, incl. necy. PVC fittings etc. and mending gooddamages to building works20x10mm Size |
| 230 | Supply & delivery of 4ft LED tube light fitting……… |
| 231 | Supply & delivery of 45 watt LED Outdoor type Luminiares along with all accessories complete……….. |
| 232 | Supply and Delivery of at site 9 watt LED bulb….. |
| 233 | Fixing only single /twin fluorescent light fitting complete with all accessories directly on wall/ceiling/HW round block and suitable size of MS fastener |
| 234 | Fixing only lamp |
| 235 | Fixing only outdoor / street light type fluorescent light fitting or MV light fitting complete with all accessories to be fixed /projected from the wall of the building incl. making holes/providing clamping arrangement & necy. GI reducer as required. S&F 40 mm GI pipe (ISI-Medium) quality 1.5 mts. average length having suitable bend S&F necy. length of 1.5 sqmm PVC insulated single core stranded annealed copper wire and making connections as required and mending good damages to wall incl. painting etc. |
| 236 | WBSEDCL Charge |
| 237 | add GST @ 18% |
| 238 | add CESS @ 1% |
AI Tender Summary
Tender Timeline
Jan 30, 2023
11:30 IST
Tender Published
Tender notice published.
CompletedFeb 13, 2023
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedFeb 15, 2023
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender