Tender For Infrastructure Strengthening Work For Setting Up Hwc At Palika Sc Under Tufanganj-Ii Development Block Dist. Cooch Behar.
Tender Value
6.99 Lakhs
Estimated cost
Bid Submission
30 Jan 2023
0 days left
EMD
14000
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
tufanganj → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Infrastructure Strengthening Work For Setting Up Hwc At Palika Sc Under Tufanganj-Ii Development Block Dist. Cooch Behar.
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in filling in foundation trenches or plinth with goodearth in layer not exceeding 150 mm. including watering andramming etc. layer by layer complete.(Payment to be made on the basis of measurment of finished quantity of work.)(c) (i) With carried earth arranged by the contractor within a radius of 3 km. including cost of carried earth. |
| 2 | and dressing bed to proper level and fillingjoints with local sandand dressing bed to proper level and fillingjoints with local sand |
| 3 | Stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed. |
| 4 | Cement concrete (1:3:6) PCC. with 30 mm down graded shingles excluding shuttering ,in ground floor and foundation |
| 5 | Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes.(ii ) River Bazree |
| 6 | Reinforcement for reinforced concrete work in all sorts of structuresincluding distribution bars, stirrups,binders etc initial straightening and removal of loose rust (if necessary),cutting to requisite length, hooking and bending to correct shape,placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction.(a) For work in founding ,basement and upto roof of ground floor.4M |
| 7 | Hire &labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of appro approved thickness with required bracing for concrete slab, beams and columns, lintels curved or straight including fitting,fixing and striking out after completion of works(upto roof of ground floor)(a) 25mm to 30 mmshuttering without staging in foundation |
| 8 | (b) shuttering above plinth |
| 9 | Brick work with 1st class bricks in cement mortar (1:6) In foundation and plinth. |
| 10 | 25 mm thick damp proof course with cement concrete with stone chips (1:1.5:3)[with graded stone aggregate 10 mm nomonal size] and admixture of water proofing compound…..as directed |
| 11 | 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor. |
| 12 | Wood work in door and window frame fittd & fixed in position complete including a protective coat ofpainting at the contact of the frame |
| 13 | Z-batten shutters of door and window as per design havings tongued and groovehalf lap jointed as per direction of the Engineer-in-Charge including fitting and fixing shutter in position, but excluding the cost of hinges and other fittings in ground floor.A) Shutter with 25mm thick planks, 19mm thick battens.(iii) Sishu, Gamar, Champ, Badam, Bhola, Morga, Hallak. 19mm thick battens(iii) Sishu, Gamar, Champ, Badam, |
| 14 | Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately)(a) 40mm X 6mm, 250mm Length |
| 15 | Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark. (ii) 50mm. X 40mm. X 2.5mm. |
| 16 | Supplying anodised aluminium catch hook with eye fitted and fixed to shutter and chowkat complete of best quality: |
| 17 | Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete:a) With continuous plate base (Hexagonal/ Round rod)(ii) 100 mm grip x 10 mm dia rod. |
| 18 | Plaster wall (to wall ,floor ,celling ,etc)with send and cement mortarincluding rornding off or chamfering conrners as directed and raking out joint or rougherning of concrete surface ,including throating ,nosing and drip couse where necessary (g.f) with 6.1cement mortar20 mm,thick plaster Inner wall |
| 19 | 15 mm thick plaster with6:1 cement mortar |
| 20 | Neat cement punning about 1.5 mm th. In wall, dado, window sills, floor, drains etc. |
| 21 | Supplying and laying true to line and level vitrified tiles of approved brand (size not less than 600 mm X 600 mm X 10 mm thick) in floor, skirting etc. set in 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry back side of tilesusing cement @ 2.91Kg./sqM or using polymerised adhesive (6 mm thick layer applied directly over finished artificial stone floor/Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per sqM below mortar only, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles / epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials, labour and all other incidental charges complete true to the manufacturer\"s specification and direction of Engineer-in-Charge. (White cement, synthetic adhesive and grout material to be supplied by the contrr]e)I) With application slurry @1.75 kg/ Sq.m, 20 mm sand cement mortar (1:4) & 2 mm thick cement slurry at back side of tiles, 0.2 kg/ Sq.m white cement for joint filling with pigment.(A) FloorA) Deep Colour & White |
| 22 | Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc.(B) WallWith Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m.(a) Area of each tile upto 0.09 Sq.m(i) Coloured decorative |
| 23 | M.S structural work with hollow section ( square or rectangle shape) conforming to IS 806-1957 & IS 1161-1958) connected to one another with bracket,cleat as per design ,drawing and dirrection of Engineer in chargecomplete including cuttingto requisite shape & size--------------------part there of Total Area(22%) |
| 24 | Aluminium sheet ridging fitted with self tapping screws, Commplete. (Minimu(A) 300 mm lapping each way(a) With 0.71 mm sheet |
| 25 | Supplying, fitting & fixing Zn-Al alloy (55% Al & 45% Zn) coating of 150 grams per sq. metre (followed by colour coated on both side) steel sheet work having minimum yield strength of 550 Mpa of trapizoidal profile of approved make (excluding the supporting frame work) fitted and fixed with 55 mm & 25 mm self tapping screw, EPDM Washer 16 mm dia & 3 mm th. washer etc. complete with 150 mm end lap and one corrugation minimum side lap. (Payment to be made on area of finished work).(i) In Roof:-a) With 0.5 mm thick sheet |
| 26 | M.S. or W.I. ornamental grill or approved designjoints continuously welded with Msor WI flat and bars for windows , railing etc. fitted and fixed with necessary screws and lugs in G.F. |
| 27 | P.V.C- False Ceiling :Providing False Ceiling made with framework of steel tube of 40mm x 20mm of not less than 18 gauge,the long and cross section will be welded with each other 1000mm to 1200mm apart the entire framework will be fixed in wall using…damages in all respect and cost of paint as required as per direction of Engineer in-Charge . |
| 28 | Applying decorative cement based paint of approved quality after preparing the surface including scraping the same thoroughly(plas tered or concrete surface) as par manufacture\"s specification in G.F |
| 29 | Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer\"s specification and as per direction of the EIC. (In Ground Floor)(b) Two Coats Inner sidei) Water based interior grade Acrylic Primer |
| 30 | Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer\"s specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer.In Ground floor (Two Coat)c) Super Protective 100% Acrylic Emulsion. |
| 31 | Removing loose scales, blisters etc. from old painted surface and thoroughly smoothening the surface to make the same suitable for receiving fresh coat of paint. |
| 32 | (a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 33 | b) Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 34 | A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary :(b) On steel or other metal surface :With super gloss (hi-gloss) -(ii) Two coats (white in shade) |
| 35 | (a) On timber or plastered surface :With super gloss (hi-gloss) -(ii) Two coats (white in shade) |
| 36 | Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding \"P\" or \"S\" trap (excluding cost of concrete for fixing). i) 580 mm X 440 mm |
| 37 | ELECTRICAL WORKS Description of ItemDistribution wiring in 1.1 KV grade single core stranded \"FR\" PVC insulated & unsheathed copper wire (Make- KEI/Havells/Finolex) in 20mm size PVC casing-capping (Precision make) incl.Necy fittings as required.2 x 36/0.3(2.5sqmm) + 1 x 22/0.3(1.5sqmm) as Ecc |
| 38 | 2 x 56/0.3 (4 sqmm) + 1 x 36/0.3 (2.5 sqmm) ECC |
| 39 | Supply & fixing 240V ,32A DP Sheet Steel Main switch on flat iron frame on wall make-Havells. |
| 40 | Supply & fixing (2+8) way SPN Distribution board double door with 1 no 40A,240V DP 8 nols 240V SP MCBs per way having breaking capacity 10Kv & characteristics on din rail as outgoing.Make Havells /ABB |
| 41 | Distribution wiring in2x22/0.3(1.5) 1.1 KV grade single core stranded \"FR\" PVC insulated & unsheathed copper wire (Make- KEI/ Havells /finolex) in 20mm size PVC casing-capping (Precision make) with 1x22/0.3(1.5sqmm) single core standed \"FR\" PVC casing-capping insulated & unsheathed copper wire for ECC, to light/fan/lamp point with piyano key type switch fixed on MS CRC sheet metal(16SGW) switch board cum JB on wall complete with 2 no.suitable size \"Ph & N\" copper bar incl. bakelite/perspex(wall matching color) top cover 3mm thick and incl. 175mm x 100 mm x 65 mm inspection box, making earthing attachment, painting the MS box and mending good damages to original finish.Avg.Run:6M |
| 42 | Distribution wiring in2x22/0.3(1.5) 1.1 KV grade single core straded \"FR\" PVC insulated & unsheathed copper wire (Make- KEI/Havells/ finolex) in 20mm size PVC casing-capping (Precision make) with 1x22/0.3(1.5sqmm) single core standed \"FR\" PVC casing-capping insulated & unsheathed copper wire for ECC, S & F 6A 5 Pin modular type plug socket (Anchor roma make) fixed on Sheet Metal switch board with 3/4 module top cover plate on wall incl. necy connection with earting attachment,painting, mending good damages to building work. PVC casing-caping on celling & surface & plug box with on surface Avg.Run:6MOn board |
| 43 | Supply & Delivery at site LED Tube light fitting 22W (Philips make, model - BN021C LED20S PSU CW GR S2 (KMDA Vetted) directly fixed on wall/ceiling by screws |
| 44 | Supply & fixing of 9 Watt, 240V, 50Hz LED blub in wall bracket.Make-Philips. |
| 45 | Fixing only lamp |
| 46 | Supply of 48 inch sweep ceiling fan Similar to --Orient New Breeze/Summer King/Usha-Striker make (UD & MA Page-23 item no-70) |
| 47 | Supplying & fixing 240V, 130 Watt, 400mm wall fan directly on wall by screws.etc as required. Make-Havells,Model-Platina HS |
| 48 | Supply & fixingMS Fan clam of two piece type for RC ceiling as per approved specification,fabricated from 40mm x 9mm flat including making good damages to building roof with satisfactory finishing and painting-(As per drawing no 475 of PWD Specification Book-May 1991). |
| 49 | Supply & fixing of 250V socket type Fan Regulator(step type) (Make-Anchor) on existing sheet metal switch board with bakelite/perspex top cover by screw after making housing for regulator knob by cutting bakelite/perspex top cover incl.making necy. connections etc. |
| 50 | Supply & fixing of 12 module GI modular switch board on following size compleate with 3 nos. copper bar with holes(Pn,N & E) fixed on Bakelite/Hard rubber insulator sheet metal inspection box (16 SWG) of the following sizes flushed in wall by housing the same after cutting brick wall incl. making earthing attachment, painting and mending good damages to building works |
| 51 | Supply& fixing 240V, 2 nos. 6A & 1 nos. 20A, plug socket with separate2 nos. 6A & 1 nos. 20A piano key type switch, indicator and 20A switch type SP MCB(Make-Anchor)on sheet metal switch board embeded in wall incl.S & F 240mm x 200mm x 65mm MS(16SWG) switch board and bakelite/perspex top cover of 3mm thick by bress screws after making housing for switch by cutting bakelite/perspex cover and making necessary as required. Computer board. |
| 52 | Supply & fixing 240V, 16-20A,piano key type switch (Brand Anchor) on existing sheet metal switch board, incl\"making necessery connection as required |
| 53 | Supply & fixing 240V,20A,piano key type socket (Brand Anchor) on existing sheet metal switch board, incl\"making necessery connection as required |
| 54 | Supply & fixing single phase 1/2 H.P 240 v, 50 Hz Pumpset(Kirloskar Chotu 0.5HP Domestic Water Motor Pump (Multicolour) (Incl. Of all accessories) |
| 55 | S & F 20A,240 V plug top(make-Anchor) |
| 56 | Supply & fixing of 230 mm exhaust fan after hole in wall and making good damages and smooth cement finish etc.as practicable as possible and providing necy. Length of PVC insulated wire and making connection for exhaust.Make-USHA. |
| 57 | S & F Al louver shutter on wall with necy. Bolts & Nuts(6mm dia x 63mm long) for 230 mm exhaust fan. |
| 58 | Supply & fixing of 30W, 240 LED flood/street light on the roof/wall of the header armor the GI pole.Make-Havelles, Endura Pearl MP 30WLED757SASYTOPCMP |
| 59 | Excavation of soil installation of Earth Electrode and filling & ramming.A) Soft Soil. |
| 60 | Extra for treatment of soil by using salt charcoal or coke for plate electrode. |
| 61 | Supply & fixing earth busbar of galvanize MS flat 25 mm x 6 mm on wall having clearance of 6 mm of wall incl.providing drill holes on the busbar complete GI bolts, nuts, washers, spacing insulators etc.as required |
| 62 | Supply & fixing of 10 SWG G.I (Hot Dip )wire for laying of PVC cable with earthing attachment mending good damages & painting with bolts, nuts, washers, spacing insulators etc. as required as mending good damages |
| 63 | Earthing with 50mm dia GI pipe 3.64mm thick x 3.04 Mts long & 1x 4 SGW GI(Hot-Dip) wire (4Mts long) ,13mm dia x 80 mm long GI double nuts double bolts and washers incl. S&F 15mm dia GI pipe protection (1Mts long) to be filled with bitumen partly under the ground level and partly above the ground level driven to an average depth of 3.65 Mts.below the ground level by ISI-Medium GI pipe. |
| 64 | GST(18%) |
| 65 | LABOUR CESS(1%) |
AI Tender Summary
Tender Timeline
Jan 20, 2023
11:30 IST
Tender Published
Tender notice published.
CompletedJan 30, 2023
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedFeb 01, 2023
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender