Indian Oil Corporation Limited-IOCL has published Tender For Provision Of Water Fountain And Other Electrical Job For Panchtatwa Garden In Paradip Refinery Township, Paradip, Odisha.. Submission Date for this Tender is 02-02-2023. Electrical Maintenance Tenders in paradip Odisha. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | Civil works for Prov of water fountain |
| 2 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work up to plinth level : |
| 3 | 1:2:4 (1 cement : 2 coarse sand (Zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 4 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : |
| 5 | 1:1.5:3 (1 cement : 1.5 coarse sand (Zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 6 | Centring and shuttering including strutting, propping etc. and removal of form work for: |
| 7 | Foundations, footings, bases for columns. |
| 8 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level: |
| 9 | Thermo-Mechanically Treated bars. |
| 10 | Brick work withcommon burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: |
| 11 | Cement mortar 1:6 (1 cement : 6 coarse sand). |
| 12 | Providing and fixing Glass mossaic tiles at finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in-Charge. |
| 13 | 12 mm cement plaster of mix : |
| 14 | 1:4 (1 cement: 4 fine sand). |
| 15 | 15 mm cement plaster on the rough side of single or half brick wall of mix : |
| 16 | 1:4 (1 cement: 4 fine sand). |
| 17 | Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-in-charge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately). |
| 18 | Applying stamping finish to the top surface of freshly laid plain/reinforced cement concrete of specific grade in porticos, sidewalks, driveways, pool decks and open yards as per direction of Engineer-in-Charge. The process shall include the following: The concrete shall be placed and screeded to the finish grade, and floated to an uniform surface by using standard finishing techniques. The approved colour hardener @ 2.7Kg/sqm shall be applied evenly to the surface of the fresh concrete by the dry shake method by sprinkling in two or more hakes, floated after each shake and trowelled only after the final floating. The approved release agent @0.113 kg/sqm shall be applied evenly to the trowelled surface before stamping of the said release agent can be applied to the flexible polyurethane stamp moulds of approved design and in required sizes to achieve final stamped pattern, These stampings shall be placed on the surface of concrete in three to four pieces at a time and tapped gently with rammers of sufficient size and weight to leave proper stamp marks and the process repeated for the remaining concrete surface till the whole concrete surface to be stamped is completed withint the time while concrete is in plastic stage of setting. After stamping the curing shall be done as per maunfacturers specifications. After initial curing the imprinted joints shall be grouted using cement slurry mixed with colour hardner as per requirement. The surface shall be sealed by applying acrylic based sealer not less than 0.167 litre/sqm on finished surface. The construction joints shall be provided by groove cutting of size 4mm x 20mm in panel size 3m x 3m or less as per the site condition and filling the same with 10mm baker rod and providing and laying PU (polyurethane) based joint sealer of approved make as per manufacturer"s specifications and finished by applying polyurethane resin based top protective clear coat of minimum 80micron applied with rollers on properly cured and dry clean surface. (Cost of concrete flooring is not included in this item which shall be paid separately). |
| 19 | Supply, Installation, Testing & Commissioning of 6 feet dia water ball fountain with following specification: A. Ball fountain body 1. Full Dandelion with arms and nozzles complete 2. Dia - 6 Ft. Dia. (full round) 3. Arms - 108 nos. (minimum) 4. Inlet Point - 2 inch Pipe 5. Body - Stainless steel 304Gr.B. Pump - Submersible Pump(Make : Kirlosker/Crompton or equivalent) 1. Submersible Pump Capacity : (Minimum) 10 HP/Three Phase 2. Discharge - 32.0 LPS(minimum) 3. Head - 12 Mtr 4. Suction & Delivery-100x100mmC. Electrical Item 1. Electrical Panel with Star Delta starter for 10 HP X 1 no. pumpset complete with MCB"s ammeter, voltmeter, single phasing preventer, indicating lights, etc. 2. Power Supply (Power Converter) 3. Programmable Color Changing LED based Water Proof Nozzle Mounted Light(24 Pre-Programmed colour patterns) 4. Master Control Device for RGB Lights 5. Including Electrical work such as Submersible cabling, conduting, etc.(Distance upto 50 Mtr.) |
| 20 | Supply, Installation, Testing & Commissioning of MULTIPLE GEYSER TYPE WATER FOUNTAIN with following specification:A. Fountain body 1. Geyser Jet Nozzle with Ball Joint -1" Dia. (25 mm) & 1.5" dia (40mm) 2. SS Light Stand for 3 Lights Fixing on Centre Jet 3. SS Light Stand for 1 Light Fixing on RingB. Pump -Submersible Pump(Make : Kirlosker/Crompton or equivalent) 1. Capacity : (Minimum) 3.0 HP/Three Phase 2. Discharge - 19.0 LPS(minimum) 3. Head - 8 Mtr 4. Suction & Delivery-80 x 80 mmC. Electrical Item 1. Electrical Panel with Star Delta starter for 3.0 HP X 1 no. pumpset complete with MCB"s ammeter, voltmeter, single phasing preventer, indicating lights, etc. 2. Power Supply (Power Converter) 3. Programmable Color Changing LED based Water Proof Nozzle Mounted Light (24 Pre-Programmed colour patterns) 5. Including Electrical work such as Submersible cabling, conduting, etc.(Distance upto 50 Mtr.) |
| 21 | Electrical works |
| 22 | LAYING OF LT POWER/ CONTROL/ TELEPHONE/ INSTRUMENT/ CCTV/ COMPUTER AND OTHER CABLES IN TRENCHES Horizontal and vertical laying of one or more armoured / unarmoured PILCA / PVC insulated and PVC sheathed / XLPE LT power (voltage grade upto 1.1 KV)/ control/ telephone/ instrument/ CCTV/ computer and other cables of following sizes in pre-excavated cable trench or existing trench/ RCC or Hume or Stoneware or Metal pipe /masonry duct, fixing of number tags ( if required), testing plus transportation from stores to site, unpacking, straightening, dressing of cable and returning the empty drum with unused cable, if any, to stores etc. all complete with labour and materials as per the drawings, specifications and directions of the Engineer-in-charge. NOTE: Cables will be supplied by the Owner free of cost. |
| 23 | Overall diameter upto 35 MM |
| 24 | LAYING OF LT POWER/ CONTROL/ TELEPHONE/ INSTRUMENT/ CCTV/ COMPUTER AND OTHER CABLES ON CABLE TRAYS/ STRUCTURES Horizontal and vertical laying of one or more armoured / unarmoured PILCA / PVC insulated and PVC sheathed / XLPE LT power (voltage grade upto 1.1 KV)/ control/ telephone/ instrument/ CCTV/ computer and other cables on cable racks/ wall and steel structures upto any height, fixing of saddles, aluminium strip, number tags ( if required), testing plus transportation from stores to site, unpacking, straightening, dressing of cable, fixing with clams/ cleats as required and returning the empty drum with unused cable, if any, to stores etc. all complete with labour and materials as per the drawings, specifications and directions of the Engineer-in-charge. NOTE: Cables will be supplied by the Owner free of cost. |
| 25 | Overall diameter upto 35 MM |
| 26 | DRESSIING OF CABLES Dressing of cable in underground trenches, cable trays/rack etc. including supply and fixing of clamps etc., wherever necessary, as per the direction of the Engineer-in-charge |
| 27 | Overall diameter upto 35 MM |
| 28 | SFI OF GI CABLE TRAY (INCL. COST OF TRAY) Supply ,fabricating and installing following sizes of perforated GI cable trays including horizontal and vertical bends, reducers, tees, cross members and other accessories as required and duly suspended from the ceiling and / or fix to steel / RCC columns, beams, or any other structure members with MS suspenders, angles, channels etc. complete as per the direction of Engineer-in-Charge |
| 29 | 100 mm x 25 mm x 2 mm |
| 30 | SUPPLY AND LAYING OF BRICKS Supply and laying of approved 2nd class bricks of thickness 75 mm in cable trench for cable protection as per the direction of Site-in-c |
| 31 | EXCAVATION OF EARTH FOR CABLE / PIPE LAYING FOR ELECTRICAL WORK Excavation of earth for cable trenches / laying of G.I. pipes for cable work in all types of soils including saturated soil upto a max. depth of 1.5 metres including shoring, strutting and bailing out of water (if necessary), backfilling and compacting in layers not exceeding 20 cm. thick to the finished ground level and disposal and dressing of excess earth within a lead of 50 metres all complete with labour and materials as per standards, drawings, specifications and directions of Engineer-in-charge. |
| 32 | ROAD CUTTING AND MAKING GOOD Cutting road and making good the same including supply of extra quantities of materials I.e. aggregate, moorum screening, red bajri and labour required. |
| 33 | Bituminous portion |
| 34 | GI PIPE LAYING (INCLUDING COST OF PIPE) Providing and laying medium quality, Class-B galvanised steel pipes of Tata / Jindal or approved equivalent make conforming to IS-1239 [Part-I] in underground trenches, on steel, concrete or similar structures including cutting, threading, bending, supply & installation of supports, clamps, small iron structures, spacer, seats, plugs, bush, fittings / fixtures like bends, tees, nipples, reducers etc. all complete as per specification, drawing and direction of Engineer-in-charge. Item includes sealing of pipe ends & joints with bushes and bitumen based fillings and such other miscellaneous works so as to make piping water tight. |
| 35 | 50 mm dia |
| 36 | PROVIDING EARTHING ELECTRODE Providing earthing electrode as per IS: 3043 standard / drawing / specifications with following sizesmedium quality, Class-B, ITC/KT/ Jindal make GI pipe fabricated as per the standard drawing and driven in the earth pit filled up with charcoal or coke dust mixed with salt clay (salt 0.5%) including providing inspection chamber as per the drawing with removable RCC (1:2:4) cover, earth, excavation, back filling, masonry work etc. all complete with labour and materials as per the direction of Engineer-in-Charge. Charcoal and salt cost will be paid seperately as extra. |
| 37 | 65 mm dia 3 metre long |
| 38 | SALT AND CHARCOAL FOR PIPE EARTHING Extra for using below given salt and charcoal for pipe earth electrode as required. Note: Unit of measurement is each which shall be measured as complete set of mentioned quantity of coke & salt. |
| 39 | 160 kg coke and 5 kg salt |
| 40 | EARTHING WITHGI / CU STRIPProviding Earthing with GI / CU strip of the following sizes including supply and laying of GI / CU strip and connecting consumables, all complete with labour and materials as per direction of Engineer-in-Charge. |
| 41 | 40 X 5 MM GI Strip |
| 42 | EARTHINGWITH GI WIRE ROPE Earthing with GI wire rope, providing and connecting equipment with earth buss bar including supply and fixing of GI wire rope of following diameter and making connection with equipment by means of GI bolts, nuts, washers, copper lugs etc. all complete with labour and materials as per direction of Engineer-in-Charge. |
| 43 | 10 MM |
| 44 | LT CABLE HEAT SHRINKABLE INDOOR / OUTDOOR CABLE END TERMINATION (INCLUDING COST OF END TERMINATION KIT) Providing end termination of power cable including cutting, stripping, providing lugs, cable insulation, providing and glanding with single/ double compression heavy duty brass cable gland conforming to IS-12943 , wherever specified, providing aluminiumlugs, crimping/ soldering, as necessary, restoration of insulation/ clamping of cable, tagging with aluminium tag,earthing of armour, connection to the equipment terminals etc. all complete with labour and materials as per standard and direction of the Engineer-in-Charge. Make of kits shall be of Raychem/ CCI/ approved equivalent make. |
| 45 | Upto 3 / 3.5 / 4 x 10 sqmm |
| 46 | 3 / 3.5 / 4 x 50 sqmm |
| 47 | SUPPLYING AND FIXING OF CC ROUTE MARKER Supplying and making cable route marker with cement concrete 1:2:4 (1 cement: 2 coars sand: 4 graded stone aggregate 20 mm nominal size) of size 60 cm x 60 cm at the bottom and 50 cmx50cm at the top with a thickness of 10 cm including inscription duly engraved as required. |
| 48 | STRUCTURAL STEEL WORK IN SINGLE SECTIONStructural steel work in single section fixed with or without connecting plate as specified belowincluding cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including supply of all material & labour,transportation etc.. |
| 49 | Without connecting plate |
| 50 | Cleaning of surface, rust removing of foreign matter, rubbing down thoroughly with emery paper, wire brush, washing with degreasing solvent (white spirit) to remove grease etc. and preparation of surface for application ofpaint by spray painting on electrical e quipment/structures/polesor any other metallic surface with two coats ofapproved brand and manufacturer Aluminium paintincluding supply of paint suitable for a temperature of 100 Degree Celsius.All complete with labour and materials as per directions of th e Engineer-in-Charge. |
| 51 | "Lettering with black Japan paint of approved brand and manufactureincluding supply of all material & labour and transportation etc Note : Unit of measurement is considered EACH which is equal to per cm height per letter." |
| 52 | SHIFTING OF PANEL/ MOTOR/ EQUIPMENT Transportation from the storeto the site or from worksite to worksite within battery area or within township of panel, motor and any other equipment alongwith all necessory accessories without any damage. All complete with labour, materials, necessary tools/ tackles and shifting vehical/ mode as per the direction of Engineer-in-Charge. Unit shall be read as EACH in place of TON |
| 53 | Equipment weighing above 500 kg and requiring hydra and tractor trolley etc. Unit shall be read as EACH in place of TON |
| 54 | ERECTION OF PANEL/MOTOR/EQUIPMENT Erection, testing and commissioning of panel, motor and any other equipment on existing foundation including carriage from Stores to the site, unpacking, placing on foundation, levelling, fixing and fitting of all components, making necessary connections, phase checking, meggering as necessary all complete with labour and materials as per the direction of Engineer-in-charge. |
| 55 | Equipment, Panels,motor etc. weighing above 500 kgand requiring hydra and tractor trolley etc.but <3MT. Unit of measurement is to be considered as EACH (EA) in place of TONNE (TO) till the next revision of M&I SOR. |
| 56 | INSTALLATION OF LIGHTING FIXTURES (EXCLUDING COST OF FIXTURES ) Fixing of following light fittings attachments on MS hanger/supports/ concrete wall structure /steel structure completed with lead in wires and other accessories all complete with labour and materials as per direction of the Engineer-in-Charge. (cost of light fittings/lamp control gears and other fittings shall be excluded). |
| 57 | Garden light fitting |
| 58 | CABLE,AL,3.5Cx50sq.mm,XLPE,SHTD,ARM, FR-LSH Cable: Power Conductor Material: Aluminium,IS : 8130-1984 Strand Type: Copper,IS : 8130-1984 Insulation Material: Extruded XLPE, conforming toIS 7098(part 1), Number of Cores: 3.5 Ambient Temperature: 40 deg C, Armoured Material: Galvanised round steel wire Maximum Operating Temperature: 90 deg C, Maximum Short Circuit Temperature: 250 deg C, Outer Sheath: PVC extruded type "ST-2" FR-LSH, chemically treated to prevent rodent ,termite attack,protected against solvent penetration and corrosive attack Voltage Grade: 1.1 KV (E), Standard Designation: IS - 7098(Part-I) with latest amendments |
| 59 | CABLE,CU,5Cx2.5sq.mm,XLPE,SHTD,ARM, FR-LSH Cable: Power Conductor Material: Copper,IS : 8130-1984 Strand Type: Copper,IS : 8130-1984 Insulation Material: Extruded XLPE, conforming toIS 7098(part 1), Number of Cores: 5 Ambient Temperature: 40 deg C, Armoured Material: Galvanised round steel wire Maximum Operating Temperature: 90 deg C, Maximum Short Circuit Temperature: 250 deg C, Outer Sheath: PVC extruded type "ST-2" FR-LSH, chemically treated to prevent rodent ,termite attack,protected against solvent penetration and corrosive attack Voltage Grade: 1.1 KV (E), Standard Designation: IS - 7098(Part-I) with latest amendments |
| 60 | 230V AC, Single Phase, 50 Hz LED BASED BOLLARD LIGHT FITTING ;10 W LED Height- 2" Enclosure- IP65 or better Outdoor type Warranty- 2 Years Burning Life- 50,000 Hrs Housing: Die cast Aluminium Make: Jaquar/Bajaj/Havells/Philips or Equivalent Model type should be aesthetically suitable &to be supplied as per direction of EIC. |
| 61 | S.No.,,Specifications,,Details A,,Specifications head 1.,,Feeder Pillar,,Outdoor Floor mounted along with 2 nos. of lifting eye hook. 2.,,Material of panel Enclosure ,,Polycarbonate (Hensel/Hager/Technic/ Spelsberg/Equivalent) Enclosure shall be transparent. 3.,,IP protection class,,IP65 (min.) 5.,,Access of feeder pillar,,From front & rear (desirable) with door locking arrangement. 6.,,Input Cable termination (Bus bar arrangement),,Input Feeder: Suitable for termination of 1run 4CX25sq.mm. Aluminum cable. Outgoing Feeder: Total 12 Nos. 7.,,Input Feeder,,63 A MCCB, 25KA, Make: Siemens/L&T/Schneider or equivalent 8.,,Cable entry,,From bottom 9. ,,Gland Plate,,Non corrosive metallic gland plate with knock out. Material to be specified. 10.,,Main Bus bar material,,Sleeved Aluminium Bus bar 11.,,Earthing,,Separate Earthing point/ bus bar for earthing of gland plates. Provision of double earthing. ,,Door,,Hinge supported panel door at panel front and back side shall be of polycarbonate with locking arrangement. 12. ,,Adapter box- below the incomer,,Metallic Adapter box with powder coat finish for main incoming cable 13.,,Canopy,,Canopy projected 300 mm in all directions for additional weather protection of thermoplastic material. 14.,,Indication Lamp,,Clustered type, LED (R,Y,B) , Voltage -240V 15.,,Time Switch,,Digital programmable time switch with 2NO & 2 NC auxiliary contacts. Contact Rating: 10Amp, 240 V AC. 17.,,Digital Voltmeter,,At Incomer 18.,,Digital Ammeter,,At Incomer 19.,,Outgoing feeder,,a.,,Rating: 10A, 30mARCCB, 1-phase, Make: ABB/ Siemens/L&T/Schneider or equivalent 20.,,Wiring Requirement,,Wiring from Time switch to Main Power contactors coil. Power contactor will get ON when Time switch will operate. 21.,,Acceptable make for Switchgear-MCCB,RCCB,,GE/ Siemens/ Schneider/ Legrand/ Hager ,,Ground clearance of the panel and other requirements,,Min 400mm. All channel and supporting angles shall be Hot dip galvanized. All fasteners shall be of SS make. 22.,,Flame retardant ,,As per relevant IEC60695 23.,,Glow Wire Test,,As per relevant IEC. 60695-2-11 24.,,UV resistance,,As per IEC 61439-1 25.,,Enclosure Colour,,RAL 7035. B.,,Documents to be submitted by Vendor 1.,,Compliance statement to all above tender technical specifications with Bill of material with makes/models of components 2.,,Vendor to submit GA drawing in accordance with above specifications along with offer for technical evaluation. 3.,,Test reports of NABL accredited labs for IP protection |
| 62 | LED Burial Light Fitting similar to Philips make BBP341 LED540/WW Or LLGB-15-C or EquivalentSupply of Light Fittings Housing: IP67 or better, 240V, 50 HZ, 1 PH AC Supply Complainec: IEC60598 Standard, Wattage- 6W/15W, CCT-3000K Initial Lumen Output ( steady State)- 540 Lumen +/- 10% or better System efficacy: >= 85 Lm/W CRI: > 70; Life Time: 50,000 Hrs, Recessed Mounting Beam angle: 20 Degree Power Factor: > 0.9, Surge Protection : 2KV/1KV, IP68 connector |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
