|
| 1 | Providind and fixing ofMonumental National Flag at SMVD University |
| 2 | Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. |
| 3 | All kinds of soil |
| 4 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. |
| 5 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: |
| 6 | 1:3:6 (1 cement :3coarse sand: 6 graded stone aggregate 20 mm nominal size) |
| 7 | Providing and laying in positionM-25 grade concrete for reinforced cement concrete work, using cement content as per approved design mix, manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying , excluding the cost of centering, shuttering finishing and reinforcement including cost of admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer- in - charge. Note: - Cement content considered in this item is @ 330 kg/ cum. Excess/ less cement used as per design mix is payable/ recoverable separately. |
| 8 | All works upto plinth level |
| 9 | Centering and shuttering including strutting, propping etc. and removal of form for: |
| 10 | Foundations, footings, bases of columns etc. for mass concrete |
| 11 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in |
| 12 | Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 13 | Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in : |
| 14 | Cement mortar 1:3 ( 1 cement : 3 coarse sand) |
| 15 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever necessabolts etc. of required size, on the top of the floor or the side of waist slab ry stainless steel nuts and bolts complete ,including fixing the railing required) and fitting the same with with necessary accessories and stainless steel dash fasteners, stainless steel with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 16 | Chequerred precast cement concrete tiles 22mm thick in footpath and courtyard, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing, cleaning and curing complete, on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand) as per direction of engineer incharge . |
| 17 | Ordinary cement with out any pigment |
| 18 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. |
| 19 | Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent |
| 20 | Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-in charge: |
| 21 | 1:3:6 or richer mix (i/c equivalent design mix) |
| 22 | Redressinglawns including weeding, cheeling the grass, forking the ground, top dressing with sludge or manure mixing the same with forked soil, watering and maintaining the lawn for 30 days or more till the grass |
| 23 | Redressinglawns including weeding, cheeling the grass, forking the ground, top dressing with sludge or manure mixing the same with forked soil, watering and maintaining the lawn for 30 days or more till the grass |
| 24 | Part B |
| 25 | Supply of 45.0 tall polygon, monumental flag mast in sections, hot dip galvanized with head frame having pulleys arrangement complete as required. Flag mast structure shall be designed considering wind velocity as per IS 875.The structural design of flag mast is included in the item. |
| 26 | Supply ofmechanical systemfor raising & lowering of flag with followingsi) double drum winch suitable for 8 mm diameter wire rope for flag hoisting and integral motor ,(1.5 HP induction motor , three phase with mechanical over load tripping mechanism with winch arrangement for hoisting of flag) with torque limiter, chain, sprocket complete as required. ii) 8 mm diameter galvanized wire rope for flag hoisting. iii) 3 numbers additional 6 mm diameter safety wire ropes.iv) Lighting finial.v) Aviations brackets 2 nos. |
| 27 | Supply of foundation bolts with nuts & washer complete with template & anchor plate as required. |
| 28 | Supply of constant glowing LED aviation light with 3X 1.5 square mm, trailing copper armoured PVC cable complete |
| 29 | Supply of specially designed 300 Watt LED outdoor, IP 65 flood light complete for façade lighting of National flag. |
| 30 | Supply of Indian national flag of size 30 ft X 45 ft made out of polyester fabric (160 gsm ), with reinforced super- strong nylon webbing on all 3 sides & eyelets complete as required. |
| 31 | Supply of flag mounting accessories like snap clamp, dog clamp, turn buckles, bobbins complete |
| 32 | Supply of ornamental crown fiber dome with embedded MS plate, to be mounted on top of flag mast. |
| 33 | Supply of electrical control panel for flag mast including reversing starter, timer, contractor, MCB etc complete as required. |
| 34 | Painting of flag mast with marine paint including etch primer suitable for hot dip galvanized surface complete as required. |
| 35 | Erection of the 45.0 meter tall flag mast with the help of suitable capacity hydraulic crane including stress fit assembly with special tools, installation of wire ropes, winch, motor with accessories, aviation lights, lighting finial, fiber dome complete as required. |
| 36 | Earthing for flag mast with 2.5 meter long, 40mm diameter GI pipe including connection to flag mast with 25x3mm GI strip complete as required. |
| 37 | ELECTRICAL |
| 38 | Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 39 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required |
| 40 | 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 41 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required |
| 42 | 25 mm |
| 43 | 32 mm |
| 44 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. |
| 45 | 1 or 2 Module (75mmX75mm) |
| 46 | 4 Module (125mmX75mm) |
| 47 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. |
| 48 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. |
| 49 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) |
| 50 | 4 way (4 + 12), Double Door |
| 51 | 6 way (4 + 18), Double door TPN DB |
| 52 | Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 53 | 40Amp |
| 54 | 63 Amp |
| 55 | Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) |
| 56 | Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required. |
| 57 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, brickprotective covering and refilling the trench etc as required. |
| 58 | Upto 35 sq. mm |
| 59 | Providing and fixing 6 SWG dia G.I. wire on surface or in recessfor loop earthing along with existing surface/ recessed conduit/submain wiring/ cable as required. |
| 60 | Providing, laying and fixing following dia RCC pipe NP2 class (light duly) in ground complete with RCC collars, jointing with cement motar 1:2 ( 1 cement : 2 fine sand ) including trenching (75 cc deep) and refilling etc as required. 100 mm |
| 61 | Supplying of XLPE,Aluminium armoured cable of 1.1KV gradel with GI Clamps,forfloor/wall with all haed ware and fixing arrangement etc. for surface laying as required. |
| 62 | 4 Core 10 Sqmm XLPE Alu arm.cable |
| 63 | 4 Core 16 Sqmm XLPE Alu arm.cable |
| 64 | Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 1.6mm thick CRCA sheet, hinged doors of 1.6mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required Bus bar:-.Electrolytic high conductivity aluminium Four Pole (full rated)busbars rated at 220/240V,50 Hz., 2000 amps, Automaticwith Ms paint coted /insulated with heat shrinkable coloured PVC sleeves,etc complete asper direction engineer inchargeSwitch gearinconer = 63 A MccB, OUTgoing =SPN 32 A -5 No\"s |
| 65 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with Chemical earthing materialas required and as per direction . |
| 66 | Supplying,Installation, testing and commissioning of pre-wired, 5wwall led recess foot lightcomplete with all accessories and tube etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. |
