Tender For Ammonia Tank Project Residual Work (Piping, Civil And Structural Work) For Interconnecting Piperack Area At Fact - Cd, Ambalamedu,Kochi, Kerala.
Tender Value
Ref. Documents
Estimated cost
Bid Submission
02 Feb 2023
0 days left
EMD
1 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
ambalamedu → Kerala
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Ammonia Tank Project Residual Work ( Piping, Civil And Structural Work ) For Interconnecting Piperack Area At Fact - Cd, Ambalamedu, Kochi, Kerala.
BOQ
| Sl. No. | Item Description |
| 1 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1m above ground level and removal of rubbish and cleared items to locations pointed out by Engineer in-charge, with in a lead of 50m. |
| 2 | Demolishing R.C.C. work manually / by mechanical means including stacking of reinforcement bars and disposal of unserviceable material with in 50m lead as per direction of Engineer in-charge. |
| 3 | Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in - charge : in cement mortar. |
| 4 | \"Dismantling steel work in single sections including dismembering and stacking with in 50m lead, as per direction of Engineer – in - charge. in Channels, angles, tees and flats.\" |
| 5 | Disposal of moorum/ building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved dumping ground for lead up to 10 km for all lifts, within the premises of FACT CD, complete as per directions of Engineer-in-Charge. |
| 6 | Charges for conveying the surplus earth to places approximately 5 kms away and dumping at low lying places as directed by the Engineer in-charge. |
| 7 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains, in all kinds of soil, including dressing of sides and ramming of bottoms, lift up to 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed by the Engineer-in -charge, with in a lead of 50m. The rates shall include bailing out water, and keeping the sides from collapsing using necessary timbering, planking, and shoring. |
| 8 | \"Casting 600mm diameter bored cast in-situ reinforced cement concrete piles, as per Engineering specification 32686-12-DA-011 R0 in M35 grade ready mix concrete after boring through Direct mud circulation method as per IS 2911- Part 1/sec 2, having minimum cement of 400 KG/M3 of concrete, using Portland Pozzolana cement confoMing to IS 1489, river sand / manufactured sand confoMing to IS 383, 20mm or less size graded hard granite broken stones, admixtures to concrete as per IS 9103, water as per IS 456 and reinforced with High strength defoMed bars of 500D/550D grade confoMing to IS 1786 for the entire length of piles. The pile shall be socketed into hardrock for a depth of 600mm(boring through rock paid separately). All the materials used in the casting of concrete shall be done with the approval of Engineer-in-charge.The rate shall include the cost for all plants, tools, materials labour and other services for boring the piles including mobilisation and demobilisation of piling rigs, boring to the required depth and stabilisation of hole with bentonite slurry or other required material to suit site conditions, making channels in the ground, making service roads and arrangements for transportation and disposal of muck (The muck will be treated as owned by the contractor and it will be the responsibility of the contractor to dispose the muck without causing environment damage with necessary peMission from the concerned authority and consultant / client to be infoMed well in advance on the disposal methodology before starting the work), cleaning the bores with water, lowering the reinforcement cages, concreting, excavating and levelling the ground exposing piles to a depth of 100mm below cut-off level after curing and gaining sufficient strength. Rate of reinforcement alone shall be paid extra - For piles of length 23m below cut-off level. (payment shall be made for length of pile below cut off level only) |
| 9 | Extra charges for boring through hard rock for a depth of 600mm over and above rates quoted for item no(8) for 600mm dia pile |
| 10 | Chipping and removing weak concrete at the top of RCC piles to the cut off level in line and levels carefully, manually / mechanically without damaging the remaining portion of pile and exposing the reinforcement, cleaning the reinforcement off any loose concrete particles and removing the debris to places pointed out within the project premises as directed by the Engineer in-charge |
| 11 | Charges for empty boring through various strata to the required diameter of pile specified in the Item above, clearing the area, collecting, conveying and disposal of muck of all types such as liquid, fluid, solid and spoil earth (The muck will be treated as owned by the contractor and it will be the responsibility of the contractor to dispose the muck without causing environment damage with necessary peMission from the concerned authority and consultant / client to be infoMed well in advance on the disposal methodology before starting the work) including hire charges for tools and plants, rigs, cost of labour, etc. complete for all depth. (Payment will be made for abandoned pile due to reasons attributable to owner and for empty boring involved in between ground level at the time of casting the piles and cut-off level of piles.) 600 mm dia. piles. |
| 12 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. |
| 13 | Supplying and stacking good earth brought from outside, at locations pointed out by the engineer in-charge |
| 14 | Providing and laying in position reinforced cement concrete work in 1:2:4 mix (1 Portland Pozzolana cement: 2 coarse river sand/manufactured sand:4 20mm nominal size graded hard granite broken stones) including all charges for mixing concrete, laying, consolidating, curing, but excluding cost of reinforcement, centering and shuttering , as per standard specifications and as directed by the Engineer in-charge for yard paving |
| 15 | Providing and laying plain cement concrete work in 1:4:8 mix (1 cement: 4 coarse river sand/manufactured sand: 8 40mm nominal size graded hard granite broken stones) including all charges for mixing concrete, laying, consolidating, curing, cost for bailing out of water, oil, liquid mud etc. from all sources in excavated pits, trenches, etc. complete at all levels as per standard specifications but excluding the cost of shuttering, and as directed by the Engineer in-charge for foundation / levelling course etc. |
| 16 | Providing and laying in position machine batched and machine mixed design mix M-30 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer incharge. (Note: - Cement content considered in this item is @ 340 KG/M3. Excess cement used as per design mix is payable separately) – for all works below plinth level |
| 17 | Providing and laying in position machine batched and machine mixed design mix M-30 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer incharge. (Note: - Cement content considered in this item is @ 340 KG/M3. Excess cement used as per design mix is payable separately) – for all works above plinth level |
| 18 | Reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size) work at all levels, excluding cost of centering, shuttering, finishing and reinforcement & including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer in-charge-For drains |
| 19 | Reinforced cement concrete work of M25 grade for precast cover slab using Portland pozzolana cement containing more than 25% of fly ash, river sand / manufactured sand confoMing to IS 383 and 20mm nominal size graded hard granite broken stones including all charges for designing the mix, weigh batching, including installation of batching plant at the designated location in the site premises or arranging MC, mixing concrete, cost of adding concrete admixtures as required, transporting, foMwork, laying, vibrating, consolidating, curing with minimal use of potable water subject to provision of IS 456, handling, transporting, loading, unloading, keeping and fixing in position, at all levels etc., complete but excluding cost of providing reinforcements. (Exposed surfaces of pre-cast elements shall have good finish with no blemish or mark on the finished surfaces) NOTE- (1) Minimum Cement content shall be @ 330 KG/M3. Excess/ less cement used as per design mix is payable/ recoverable separately. (2) Fly ash confoMing to grade I of IS 3812 (Part-1) only be used as part replacement of OPC as per IS: 456. UnifoM blending with cement to be ensured in accordance with clauses 5.2 and 5.2.1 of IS:456 - in the items of BMC and MC -for cover slabs (75mm to 100mm thick) on drain |
| 20 | Add for using extra cement in the items of design mix over and above the specified cement content therein. |
| 21 | Providing form work to cement concrete and RCC works with necessary plywood / steel sheet, steel joists, runners, struts, posts etc with adjustable spans and telescopic posts, wooden planks etc. including removal after completion /curing at all levels for foundation footings, bases of columns and walls and for mass concrete with straight sides. |
| 22 | \"Providing form work to cement concrete and RCC works with necessary plywood / steel sheet, steel joists, runners, struts, posts etc with adjustable spans and telescopic posts, wooden planks etc. including removal after completion /curing at all levels for Columns, Pillars, Piers, Abutments, Posts and Struts. Rate to include for shuttering at all heights\" |
| 23 | Providing form work to cement concrete and RCC works with necessary plywood / steel sheet, steel joists, runners, struts, posts etc with adjustable spans and telescopic posts, wooden planks etc. including removal after completion /curing at all levels for Lintels, beams, plinth beams, girders, bressumers and cantilevers. Rate to include for shuttering at all heights |
| 24 | Supplying, fabricating, conveying, and fixing reinforcement to RCC works at all levels with high strength deformed bars Fe 500D/ 550D grade Thermo Mechanically Treated (TMT) bars confoMing to IS 1786 including all charges for uncoiling and straightening rods, cutting rods, bending cold, placing in position and supplying & tying with black annealed tying wire of 16 gauge, etc. complete. |
| 25 | Supplying, conveying, fabrication and erection of MS single section members such as channels, guard rail, MS angle hand rails verticals, etc. with fixtures such as end stops, clamps, bolts and nuts etc. including charges for cutting, splicing, drilling holes as required, fixing to lines and levels and cleaning thoroughly with power tools and painting with two coats of synthetic enamel of approved shade over two coats of red oxide zinc chromate primer. |
| 26 | Supply, fabrication and erection of structural steel work in built up trusses bolted or welded at all levels with MS angles, channels, tees, flats, RSJs, rods, pipes, hollow rectangular sections and plates for roof trusses, purlins, cladding, gratings, runners etc. including cutting, welding, hoisting, erecting in position with necessary MS bolts including preparation of surface by grit/shot blasting at all heights including hire of plants and equipments, labour and costs of grits, shots. After grit/shot blasting the surface shall exhibit almost clean white metal and shall have surface finish of Sa 2 ½ asper IS 9954. (Mill scale, rust & foreign matter shall be removed to the extent that only traces remaining are slight stains in the foM of spots or strip)The rate shall include erecting necessary scaffolding works wherever required and covering working area during blast cleaning with tarpaulin of good quality to prevent spreading of dust, paint to the nearby operating areas and painting with two coats of synthetic enamel of approved shade over two coats of red oxide zinc chromate primer. |
| 27 | Providing and fixing mild steel round holding down bolts with nuts and washer plates complete and painting with two coats of synthetic enamel of approved shade over two coats of red oxide zinc chromate primer. |
| 28 | Supplying and fixing chemical anchor bolts of HILTI or equivalent etc for anchoring the structural members to existing concrete column/beam as per manufactures specification. etc. complete to lines and levels at all levels with 12mm dia bolts (HIT-V Threaded rod or equivalent) fixed with Re500 V4 adhesive of HILTI or equivalent |
| 29 | Supplying and grouting pockets, base plates, etc. at all levels for static equipments /structural steel supports using nonshrink grout shrinkkomp 10 of M/s ACC or Conbextra GP I of M/s FOSROC or equivalent. |
| 30 | Supply of Metallic Pipes - LTCS, A333 GR.6, SMLS, BE, ASME B 36.10, SCH 40, 80 NB, as per TPS 32686-03-PS-004/Engineering specification 03ES301/10. |
| 31 | Supply of Metallic Pipes - CS, A106 GR.B, SMLS, BE, ASME B 36.10, SCH 40, 80 NB, IBR, as per TPS 32686-03-PS-004/Engineering specification 03ES301/10. |
| 32 | Supply of Metallic Pipes - CS, A106 GR.B, SMLS, BE, ASME B 36.10, SCH 40, 50 NB, as per TPS 32686-03-PS-004/Engineering specification 03ES301/10. |
| 33 | Supply of Metallic Pipes- CS-GLV, IS1239 ERW Galvanised, ERW, BE, IS-1239-I, HVY, 50 NB, as per TPS 32686-03-PS-004/Engineering specification 03ES301/10. |
| 34 | Supply of Metallic Pipes- CS, IS1239-1, ERW, BE, IS-1239-I, HVY, 50 NB, as per TPS 32686-03-PS-004/Engineering specification 03ES301/10. |
| 35 | Supply of Metallic Pipes- CS, A106 GR.B, SMLS, BE, ASME B 36.10, SCH 80, 25 NB, as per TPS 32686-03-PS-004/Engineering specification 03ES301/10. |
| 36 | Supply of Metallic Pipes- CS, A106 GR.B, SMLS, BE, ASME B 36.10, SCH 80, 20 NB, IBR, as per TPS 32686-03-PS-004/Engineering specification 03ES301/10. |
| 37 | Supply of Metallic Flanges – WN, A350GR.LF2CL.1, RF, B16.5, 300#, 80NB to suit pipe thk. SCH 40, as per TPS 32686-03-PS-005/Engineering specification 03ES302/10. |
| 38 | Supply of Metallic Flanges – WN, A105, RF, B16.5, 300#, 80NB to suit pipe thk. SCH 40, as per TPS 32686-03-PS-005/Engineering specification 03ES302/10. |
| 39 | Supply of Metallic Flanges – WN, A105, IBR, RF, B16.5, 150#, 80NB, to suit pipe thk. SCH 40, as per TPS 32686-03-PS-005/Engineering specification 03ES302/10. |
| 40 | Supply of Metallic Flanges – THD, A105, GALVANISED RF, B16.5, 150#, 50NB to suit pipe thk. SCH 40, as per TPS 32686-03-PS-005/Engineering specification 03ES302/10. |
| 41 | Supply of Metallic Flanges – WN, A105, RF, B16.5, 150#, 50NB to suit pipe thk. SCH 40, as per TPS 32686-03-PS-005/Engineering specification 03ES302/10. |
| 42 | Supply of Metallic Flanges – SO, A105, RF, B16.5, 150#, 50NB to suit pipe thk. HVY(IS1239), as per TPS 32686-03-PS-005/Engineering specification 03ES302/10. |
| 43 | Supply of Metallic Flanges – WN, A105, IBR, RF, B16.5, 150#, 50NB, to suit pipe thk. SCH 40, as per TPS 32686-03-PS-005/Engineering specification 03ES302/10. |
| 44 | Supply of Metallic Flanges – SW, A105, RF, B16.5, 150#, 25NB, as per TPS 32686-03-PS-005/Engineering specification 03ES302/10. |
| 45 | Supply of Metallic Flanges – BLIND, A350GR.LF2CL.1, RF, B16.5, 300#, 80NB, as per TPS 32686-03-PS-005/Engineering specification 03ES302/10. |
| 46 | Supply of Metallic Flanges - FIG-8 BLIND, A350GR.LF2CL.1, FF, B16.48, 300#, 80NB, as per TPS 32686-03-PS-005/Engineering specification 03ES302/10. |
| 47 | Supply of Metallic Pipe Fittings - 90LR, A420 GR.WPL6, SMLS, BW, B16.9, SCH 40, 80NB, as per TPS 32686-03-PS-006/Engineering specification 03ES303 / 10. |
| 48 | Supply of Metallic Pipe Fittings - 90LR, A234GR.WPB, IBR, SMLS, BW, B16.9, SCH 40, 80NB, as per TPS 32686-03-PS-006/Engineering specification 03ES303 / 10. |
| 49 | Supply of Metallic Pipe Fittings - 90LR, A234 GR.WPB-GALVANIZED, FGD, THD, B16.11, SCH 80, 50NB,as per TPS 32686-03-PS-006/Engineering specification 03ES303 / 10. |
| 50 | Supply of Metallic Pipe Fittings - 90LR, A234GR.WPB, SMLS, BW, B16.9, SCH 40, 50NB,as per TPS 32686-03-PS-006/Engineering specification 03ES303 / 10. |
| 51 | Supply of Metallic Pipe Fittings - 90LR, A234GR.WPB, SMLS, BW, B16.9, SCH 80, 50NB,as per TPS 32686-03-PS-006/Engineering specification 03ES303 / 10. |
| 52 | Supply of Metallic Pipe Fittings - 90LR, A105, FGD, 3000 rating, SW, B16.11, 25NB, as per TPS 32686-03-PS-006/Engineering specification 03ES303 / 10. |
| 53 | Supply of Metallic Pipe Fittings - 90LR, A234GR.WPB, IBR, SMLS, BW, B16.9, SCH 80, 20NB, as per TPS 32686-03-PS-006/Engineering specification 03ES303 / 10. |
| 54 | Supply of Metallic Pipe Fittings - EQT, A420 GR.WPL6, SMLS, BW, B16.9, 80NB, as per TPS 32686-03-PS-006/Engineering specification 03ES303 / 10. |
| 55 | Supply of Metallic Pipe Fittings - EQT, A234GR.WPB, IBR, SMLS, BW, B16.9, SCH 40, 80NB, as per TPS 32686-03-PS-006/Engineering specification 03ES303 / 10. |
| 56 | Supply of Metallic Pipe Fittings - EQT, A234 GR.WPB-GALVANIZED, FGD, THD, B16.11, SCH 80, 50NB, as per TPS 32686-03-PS-006/Engineering specification 03ES303 / 10. |
| 57 | Supply of Metallic Pipe Fittings - EQT, A234GR.WPB, SMLS, BW, B16.9, SCH 80, 50NB, as per TPS 32686-03-PS-006/Engineering specification 03ES303 / 10. |
| 58 | Supply of Metallic Pipe Fittings - EQT, A105, FGD, 3000 rating, SW, B16.11, 25NB, as per TPS 32686-03-PS-006/Engineering specification 03ES303 / 10. |
| 59 | Supply of Metallic Pipe Fittings - EQT, A105,IBR, SMLS, BW, B16.9, SCH 80, 20NB, as per TPS 32686-03-PS-006/Engineering specification 03ES303 / 10. |
| 60 | Supply of Metallic Pipe Fittings - FPLG, A105, FGD, 3000 rating, SW, B16.11, 25NB, as per TPS 32686-03-PS-006/Engineering specification 03ES303 / 10. |
| 61 | Supply of Metallic Pipe Fittings - FPLG, A105 GALVANISED, FGD, 3000 rating, THD, B16.11, SCH 80, 50NB, as per TPS 32686-03-PS-006/Engineering specification 03ES303 / 10. |
| 62 | Supply of Metallic Pipe Fittings - UNION, A105 GALVANISED, FGD, 3000 rating, THD, B16.11, SCH 80, 50NB, as per TPS 32686-03-PS-006/Engineering specification 03ES303 / 10. |
| 63 | Supply of Metallic Pipe Reduced Fittings - ECC, A234GR.WPB, IBR, SMLS, BE, B16.9, SCH 40 x SCH 40, 80 NB x 50 NB, as per TPS 32686-03-PS-006/Engineering specification 03ES303 / 10. |
| 64 | Supply of Metallic Pipe Reduced Fittings - CSWG, A105, IBR, BE, BS3799, SCH 40 x SCH 80, 50 NB x 25 NB, as per TPS 32686-03-PS-006/Engineering specification 03ES303 / 10. |
| 65 | Supply of Metallic Pipe Reduced Fittings - ECC, A234GR.WPB, BE, B16.9, SCH 40 x SCH 40, 150 NB x 80 NB, as per TPS 32686-03-PS-006/Engineering specification 03ES303 / 10. |
| 66 | Supply of Pipeline Gaskets - Spiral Wound Gasket with Inner and Centering Rings, Filler Material: Graphite Tape, Winding Material: 316 SS, Inner Ring Material: 316 SS, Centering Ring Material: 316 SS - B16.20, 4.5mm thk., 80 NB, to suit flange - RF, 300#, B16.5, as per TPS 32686-03-PS-007/Engineering specification 03ES305 / 10. |
| 67 | Supply of Pipeline Gaskets - Spiral Wound Gasket with Inner and Centering Rings Filler Material: Graphite Tape, Winding Material: 316 SS, Inner Ring Material: 316 SS, Centering Ring Material: 316 SS - B16.20, 4.5mm thk., 80 NB, to suit flange - RF, 150#, B16.5, as per TPS 32686-03-PS-007/Engineering specification 03ES305 / 10. |
| 68 | Supply of Pipeline Gaskets - Spiral Wound Gasket with Inner and Centering Rings, Filler Material: Graphite Tape, Winding Material: 316 SS, Inner Ring Material: 316 SS - B16.20, 4.5mm thk., 50 NB, to suit flange - RF, 150#, B16.5, as per TPS 32686-03-PS-007/Engineering specification 03ES305 / 10. |
| 69 | Supply of Pipeline Gaskets - Non-asbestos Sheet Gasket General Use (Design Temperature =< 100 degC) - B16.21, 3mm thk., 50 NB, to suit flange - RF, 150#, B16.5, as per TPS 32686-03-PS-007/Engineering specification 03ES305 / 10. |
| 70 | Supply of Pipeline Gaskets - Non-asbestos Sheet Gasket General Use (Design Temperature =< 100 degC) - B16.21, 3mm thk., 25 NB, to suit flange - RF, 150#, B16.5, as per TPS 32686-03-PS-007/Engineering specification 03ES305 / 10. |
| 71 | Supply of Bolts & Nuts – STUD, A320GR.L7, M20 x 110mm,and HEX NUT, A194GR.7, as per TPS 32686-03-PS-008/Engineering specification 03ES306 / 10. |
| 72 | Supply of Bolts & Nuts – STUD, A193GR.B7, M20 x 110mm, and HEX NUT, A194GR.2H, as per TPS 32686-03-PS-008/Engineering specification 03ES306 / 10. |
| 73 | Supply of Bolts & Nuts – STUD, A193GR.B7, M16 x 95mm, and HEX NUT, A194GR.2H, as per TPS 32686-03-PS-008/Engineering specification 03ES306 / 10. |
| 74 | Supply of Bolts & Nuts – STUD, A193GR.B7, M16 x 85mm, and HEX NUT, A194GR.2H as per TPS 32686-03-PS-008/Engineering specification 03ES306 / 10. |
| 75 | Supply of Bolts & Nuts – STUD, A193GR.B7, M16 x 90mm, and HEX NUT, A194GR.2H, as per TPS 32686-03-PS-008/Engineering specification 03ES306 / 10. |
| 76 | Supply of Bolts & Nuts – STUD, A193GR.B7, M14 x 70mm, and HEX NUT, A194GR.2H, as per TPS 32686-03-PS-008/Engineering specification 03ES306 / 10. |
| 77 | Supply of Valve - VAF322, GATE VALVE, A352GR.LCB/304+HF BB,OS&Y HANDWHEEL EXTENDED BONNET, WITH CAVITY RELIEF, RF, API 600, 300#, 80 NB, as per TPS No. 32686-03-PS-009 (Engineering specification 03ES307/10, Doc. no.FKAT-ED-000-PIP-SPC-0001). |
| 78 | Supply of Valve - VAF211XZ, GATE VALVE, A216GR.WCB/#8 BB,OS&Y HANDWHEEL DRILLED, TAPPED & PLUGGED AT LOCATIONS A & G PER MSSSP-45, IBR, RF, API 600, 150#,80 NB, as per TPS No. 32686-03-PS-009 (Engineering specification 03ES307/10, Doc. no.FKAT-ED-000-PIP-SPC-0001). |
| 79 | Supply of Valve - VAF211, GATE VALVE, A216GR.WCB/#8 BB,OS&Y HANDWHEEL, RF, API 600, 150#, 50 NB, as per TPS No. 32686-03-PS-009 (Engineering specification 03ES307/10, Doc no.FKAT-ED-000-PIP-SPC-0001). |
| 80 | Supply of Valve - VAS411, GATE VALVE, A105/#8 BB,OS&Y API 602 HANDWHEEL, SW, API 602, 800#, 25 NB, as per TPS No. 32686-03-PS-009 (Engineering specification 03ES307/10, Doc no.FKAT-ED-000-PIP-SPC-0001). |
| 81 | Supply of Valve - VAS411, GATE VALVE, A105/#8 BB,OS&Y API 602 HANDWHEEL, SW, API 602, 800#, 20 NB, as per TPS No. 32686-03-PS-009 (03ES307/10, FKAT-ED-000-PIP-SPC-0001). |
| 82 | Supply of Steam Trap, ST - 001, SW, A105/SS3I6, 20 NB, as per TPS No. 32686-03-PS-010 (Engineering specification 03ES304/10, Data Sheet 32686-03-PS-ST001). |
| 83 | Butt welding & Fillet Welding - 80 NB, BW, SCH 40, MATERIAL: CARBON STEEL ( A 333 Gr. 6,ASME A 106 Gr. B/IS1239), with / without reinforcement, as per Engineering Specification 25ES205 / 10.The rate for weld joint shall include all costs associated with making a joint such as cleaning, marking out, cutting, profiling, beveling, grinding, aligning, fitting, up, tack welding,cleaning, chipping, preheating, placing of wind shields and / wind or weather protection and final welding together with any special welding requirement (including but not limited to inert gas welding) and final cleaning of welds . This item shall include preparation, final alignment, butt / seal / socket fillet welding of fabricated pipe sections, spool pieces, fitting valves, flanges / orifice flanges etc. and closing length installed and roughly aligned into the respective position and align on respective supports.For branch welding with reinforcement, the rate shall include all costs towards fabrication and welding of reinforecement ring also. Branch welding without reinforcement pad shall be considered as one pipe weld. Rate for branch welding with reinforcement pad shall be taken as 1.5 times the rate for ordinary pipe weld.The rates does not cover stress releaving, radiography/Ultrasonic/DP tests.Payment shall be made on the basis of number of weld joints completed. Welding of sockolets, weldolets, threadolets and such fittings shall be paid according to the size of the fitting and not according to the size of the piping to which it is attached.Payment for non specified sizes/thickness will be made propotional to the product of nominal bore and thickness of the pipe based on the nearest avilable size / thickness. |
| 84 | Butt welding & Fillet Welding - 50 NB, BW, SCH 80, MATERIAL: CARBON STEEL ( A 333 Gr. 6,ASME A 106 Gr. B/IS1239) with / without reinforcement, as per Engineering Specification 25ES205 / 10.The rate for weld joint shall include all costs associated with making a joint such as cleaning, marking out, cutting, profiling, beveling, grinding, aligning, fitting, up, tack welding,cleaning, chipping, preheating, placing of wind shields and / wind or weather protection and final welding together with any special welding requirement (including but not limited to inert gas welding) and final cleaning of welds . This item shall include preparation, final alignment, butt / seal / socket fillet welding of fabricated pipe sections, spool pieces, fitting valves, flanges / orifice flanges etc. and closing length installed and roughly aligned into the respective position and align on respective supports.For branch welding with reinforcement, the rate shall include all costs towards fabrication and welding of reinforecement ring also. Branch welding without reinforcement pad shall be considered as one pipe weld. Rate for branch welding with reinforcement pad shall be taken as 1.5 times the rate for ordinary pipe weld.The rates does not cover stress releaving, radiography/Ultrasonic/DP tests.Payment shall be made on the basis of number of weld joints completed. Welding of sockolets, weldolets, threadolets and such fittings shall be paid according to the size of the fitting and not according to the size of the piping to which it is attached.Payment for non specified sizes/thickness will be made propotional to the product of nominal bore and thickness of the pipe based on the nearest avilable size / thickness. |
| 85 | Butt welding & Fillet Welding - 50 NB, BW, SCH 40, MATERIAL: CARBON STEEL ( A 333 Gr. 6,ASME A 106 Gr. B/IS1239) with / without reinforcement, as per Engineering Specification 25ES205 / 10.The rate for weld joint shall include all costs associated with making a joint such as cleaning, marking out, cutting, profiling, beveling, grinding, aligning, fitting, up, tack welding,cleaning, chipping, preheating, placing of wind shields and / wind or weather protection and final welding together with any special welding requirement (including but not limited to inert gas welding) and final cleaning of welds . This item shall include preparation, final alignment, butt / seal / socket fillet welding of fabricated pipe sections, spool pieces, fitting valves, flanges / orifice flanges etc. and closing length installed and roughly aligned into the respective position and align on respective supports.For branch welding with reinforcement, the rate shall include all costs towards fabrication and welding of reinforecement ring also. Branch welding without reinforcement pad shall be considered as one pipe weld. Rate for branch welding with reinforcement pad shall be taken as 1.5 times the rate for ordinary pipe weld.The rates does not cover stress releaving, radiography/Ultrasonic/DP tests.Payment shall be made on the basis of number of weld joints completed. Welding of sockolets, weldolets, threadolets and such fittings shall be paid according to the size of the fitting and not according to the size of the piping to which it is attached.Payment for non specified sizes/thickness will be made propotional to the product of nominal bore and thickness of the pipe based on the nearest avilable size / thickness. |
| 86 | Butt welding & Fillet Welding - 50 NB, SO, SCH 40, MATERIAL: CARBON STEEL ( A 333 Gr. 6,ASME A 106 Gr. B/IS1239) with / without reinforcement, as per Engineering Specification 25ES205 / 10.The rate for weld joint shall include all costs associated with making a joint such as cleaning, marking out, cutting, profiling, beveling, grinding, aligning, fitting, up, tack welding,cleaning, chipping, preheating, placing of wind shields and / wind or weather protection and final welding together with any special welding requirement (including but not limited to inert gas welding) and final cleaning of welds . This item shall include preparation, final alignment, butt / seal / socket fillet welding of fabricated pipe sections, spool pieces, fitting valves, flanges / orifice flanges etc. and closing length installed and roughly aligned into the respective position and align on respective supports.For branch welding with reinforcement, the rate shall include all costs towards fabrication and welding of reinforecement ring also. Branch welding without reinforcement pad shall be considered as one pipe weld. Rate for branch welding with reinforcement pad shall be taken as 1.5 times the rate for ordinary pipe weld.The rates does not cover stress releaving, radiography/Ultrasonic/DP tests.Payment shall be made on the basis of number of weld joints completed. Welding of sockolets, weldolets, threadolets and such fittings shall be paid according to the size of the fitting and not according to the size of the piping to which it is attached.Payment for non specified sizes/thickness will be made propotional to the product of nominal bore and thickness of the pipe based on the nearest avilable size / thickness. |
| 87 | Butt welding & Fillet Welding - 25 NB, SW,SCH 80, MATERIAL: CARBON STEEL ( A 333 Gr. 6,ASME A 106 Gr. B/IS1239) with / without reinforcement, as per Engineering Specification 25ES205 / 10.The rate for weld joint shall include all costs associated with making a joint such as cleaning, marking out, cutting, profiling, beveling, grinding, aligning, fitting, up, tack welding,cleaning, chipping, preheating, placing of wind shields and / wind or weather protection and final welding together with any special welding requirement (including but not limited to inert gas welding) and final cleaning of welds . This item shall include preparation, final alignment, butt / seal / socket fillet welding of fabricated pipe sections, spool pieces, fitting valves, flanges / orifice flanges etc. and closing length installed and roughly aligned into the respective position and align on respective supports.For branch welding with reinforcement, the rate shall include all costs towards fabrication and welding of reinforecement ring also. Branch welding without reinforcement pad shall be considered as one pipe weld. Rate for branch welding with reinforcement pad shall be taken as 1.5 times the rate for ordinary pipe weld.The rates does not cover stress releaving, radiography/Ultrasonic/DP tests.Payment shall be made on the basis of number of weld joints completed. Welding of sockolets, weldolets, threadolets and such fittings shall be paid according to the size of the fitting and not according to the size of the piping to which it is attached.Payment for non specified sizes/thickness will be made propotional to the product of nominal bore and thickness of the pipe based on the nearest avilable size / thickness. |
| 88 | Butt welding & Fillet Welding - 20 NB, SW, SCH 80, MATERIAL: CARBON STEEL ( A 333 Gr. 6,ASME A 106 Gr. B/IS1239) with / without reinforcement, as per Engineering Specification 25ES205 / 10.The rate for weld joint shall include all costs associated with making a joint such as cleaning, marking out, cutting, profiling, beveling, grinding, aligning, fitting, up, tack welding,cleaning, chipping, preheating, placing of wind shields and / wind or weather protection and final welding together with any special welding requirement (including but not limited to inert gas welding) and final cleaning of welds . This item shall include preparation, final alignment, butt / seal / socket fillet welding of fabricated pipe sections, spool pieces, fitting valves, flanges / orifice flanges etc. and closing length installed and roughly aligned into the respective position and align on respective supports.For branch welding with reinforcement, the rate shall include all costs towards fabrication and welding of reinforecement ring also. Branch welding without reinforcement pad shall be considered as one pipe weld. Rate for branch welding with reinforcement pad shall be taken as 1.5 times the rate for ordinary pipe weld.The rates does not cover stress releaving, radiography/Ultrasonic/DP tests.Payment shall be made on the basis of number of weld joints completed. Welding of sockolets, weldolets, threadolets and such fittings shall be paid according to the size of the fitting and not according to the size of the piping to which it is attached.Payment for non specified sizes/thickness will be made propotional to the product of nominal bore and thickness of the pipe based on the nearest avilable size / thickness. |
| 89 | Installation of Straight or Fabricated Pipe - CS Pipe, 80NB, as per Engineering Specification 25ES205 / 10.The rate covers all the works required for the proper installation, above ground / in trenches of all types of carbon steel, IBR, Alloy Steel and Stainlesssteel piping and prefabricated piping sections including, The work shall include transportation from owners storage point, handling, rigging, scaffolding, placing and alignment of pipe and fittings into their respective positions and on to their respective supports. Fabrication and erection of trunnion supports, installation of special items like bellows, strainers, traps, etc. are also included in this rate. Hydraulic/pneumatic testing of the piping systems, flushing, draining and drying up shall also be included in the quoted rate.Excluded from this item shall be installation of pipe supports other than trunnions, installation of hangers, making of flanged connections,installation of valves, control valves etc., and any other item specifically exempted and paid for under separate bid items.The contractor shall make the most economical use of straight pipe length in the fabrication and field erection of straight piping runs and closing lengths.The pay quantityshall be theactualcentrelinelength in meters, of straight or fabricated pipe excluding pipe supports,valves,control valves etc.actuallyinstalled or required . Paymentforthework done will be made only whenthe piping is properly located and peMenantly supported in its final position in the field after hydrotesting. |
| 90 | Installation of Straight or Fabricated Pipe - CS Pipe, 50NB, as per Engineering Specification 25ES205 / 10.The rate covers all the works required for the proper installation, above ground / in trenches of all types of carbon steel, IBR, Alloy Steel and Stainless steel piping and prefabricated piping sections including, The work shall include transportation from owners storage point, handling, rigging, scaffolding, placing and alignment of pipe and fittings into their respective positions and on to their respective supports. Fabrication and erection of trunnion supports, installation of special items like bellows, strainers, traps, etc. are also included in this rate. Hydraulic/pneumatic testing of the piping systems, flushing, draining and drying up shall also be included in the quoted rate.Excluded from this item shall be installation of pipe supports other than trunnions, installation of hangers, making of flanged connections,installation of valves, control valves etc., and any other item specifically exempted and paid for under separate bid items.The contractor shall make the most economical use of straight pipe length in the fabrication and field erection of straight piping runs and closing lengths.The pay quantityshall be theactualcentrelinelength in meters, of straight or fabricated pipe excluding pipe supports,valves,control valves etc.actuallyinstalled or required . Paymentforthework done will be made only whenthe piping is properly located and peMenantly supported in its final position in the field after hydrotesting. |
| 91 | \"Installation of Straight or Fabricated Pipe - CS Pipe, 25NB, as per Engineering Specification 25ES205 / 10.The rate covers all the works required for the proper installation, above ground / in trenches of all types of carbon steel, IBR, Alloy Steel and Stainlesssteel piping and prefabricated piping sections including, The work shall include transportation from owners storage point, handling, rigging, scaffolding, placing and alignment of pipe and fittings into their respective positions and on to their respective supports. Fabrication and erection of trunnion supports, installation of special items like bellows, strainers, traps, etc. are also included in this rate. Hydraulic/pneumatic testing of the piping systems, flushing, draining and drying up shall also be included in the quoted rate.Excluded from this item shall be installation of pipe supports other than trunnions, installation of hangers, making of flanged connections,installation of valves, control valves etc., and any other item specifically exempted and paid for under separate bid items.The contractor shall make the most economical use of straight pipe length in the fabrication and field erection of straight piping runs and closing lengths.The pay quantityshall be theactualcentrelinelength in meters, of straight or fabricated pipe excluding pipe supports,valves,control valves etc.actuallyinstalled or required . Paymentforthework done will be made only whenthe piping is properly located and peMenantly supported in its final position in the field after hydrotesting.\" |
| 92 | \"Installation of Straight or Fabricated Pipe - CS Pipe, 20NB, as per Engineering Specification 25ES205 / 10.The rate covers all the works required for the proper installation, above ground / in trenches of all types of carbon steel, IBR, Alloy Steel and Stainlesssteel piping and prefabricated piping sections including, The work shall include transportation from owners storage point, handling, rigging, scaffolding, placing and alignment of pipe and fittings into their respective positions and on to their respective supports. Fabrication and erection of trunnion supports, installation of special items like bellows, strainers, traps, etc. are also included in this rate. Hydraulic/pneumatic testing of the piping systems, flushing, draining and drying up shall also be included in the quoted rate.Excluded from this item shall be installation of pipe supports other than trunnions, installation of hangers, making of flanged connections,installation of valves, control valves etc., and any other item specifically exempted and paid for under separate bid items.The contractor shall make the most economical use of straight pipe length in the fabrication and field erection of straight piping runs and closing lengths.The pay quantityshall be theactualcentrelinelength in meters, of straight or fabricated pipe excluding pipe supports,valves,control valves etc.actuallyinstalled or required . Paymentforthework done will be made only whenthe piping is properly located and peMenantly supported in its final position in the field after hydrotesting.\" |
| 93 | \"Installation of Flange - B16.5, 80 NB as per Engineering Specification 25ES205 / 10.The work under this item covers all operations necessary to complete a flanged joint and shall include transportation from owners storage point, handling, cleaning and preparation of flange faces and gaskets, placing, aligning, installation of gaskets, bolts/studs, final aligment and tightening of pipe flanges, orifice flanges, blind flanges, expansion joint flanges flanged valves and fittings etc. at all elevations. Installation of orifices, spades, blinds are also included in the quoted rate. The rate is applicable for all ratings and materials. The pay quantity for the items shall be number of pairs of flanges actually completed.\" |
| 94 | \"Installation of Flange - B16.5, 50NB, as per Engineering Specification 25ES205 / 10.The work under this item covers all operations necessary to complete a flanged joint and shall include transportation from owners storage point, handling, cleaning and preparation of flange faces and gaskets, placing, aligning, installation of gaskets, bolts/studs, final aligment and tightening of pipe flanges, orifice flanges, blind flanges, expansion joint flanges flanged valves and fittings etc. at all elevations. Installation of orifices, spades, blinds are also included in the quoted rate. The rate is applicable for all ratings and materials. The pay quantity for the items shall be number of pairs of flanges actually completed.\" |
| 95 | \"Installation of Flange - B16.5, 25NB, as per Engineering Specification 25ES205 / 10.The work under this item covers all operations necessary to complete a flanged joint and shall include transportation from owners storage point, handling, cleaning and preparation of flange faces and gaskets, placing, aligning, installation of gaskets, bolts/studs, final aligment and tightening of pipe flanges, orifice flanges, blind flanges, expansion joint flanges flanged valves and fittings etc. at all elevations. Installation of orifices, spades, blinds are also included in the quoted rate. The rate is applicable for all ratings and materials. The pay quantity for the items shall be number of pairs of flanges actually completed.\" |
| 96 | \"Installation of Valves - Gate valve, FLG, CS, 80NB, as per Engineering Specification 25ES205 / 10.The rate covers all works required to install all on-line items like valves, control valves, safety valves, flowmeters, steam taps etc. in the piping at all elevations. The work shall include transporatation from owners storage point. handling, rigging, lifting, placing & final alignment of valves in to their Respective positions & orientation to suit operationg conditions. The rate is applicable for all matls, types & rating. Werlding and making of flanged connections are excluded from this rate and they will be paid as per schedule A & B.2Also included under this items shall be any work required to ensure the initial satisfactory operation of the valve including minor gland/plud adjustments, lubrication and minor adjustments to the operationg mechanism. After erection in place, the valves shall be fully opened and then, after ensuring free movement, shall be closed.The pay quantity shall be the no of items installed.\" |
| 97 | \"Installation of Valves - Gate valve, FLG, CS, 50NB, as per Engineering Specification 25ES205 / 10.The rate covers all works required to install all on-line items like valves, control valves, safety valves, flowmeters, steam taps etc. in the piping at all elevations. The work shall include transporatation from owners storage point. handling, rigging, lifting, placing & final alignment of valves in to their Respective positions & orientation to suit operationg conditions. The rate is applicable for all matls, types & rating. Werlding and making of flanged connections are excluded from this rate and they will be paid as per schedule A & B.2Also included under this items shall be any work required to ensure the initial satisfactory operation of the valve including minor gland/plud adjustments, lubrication and minor adjustments to the operationg mechanism. After erection in place, the valves shall be fully opened and then, after ensuring free movement, shall be closed.The pay quantity shall be the no of items installed.\" |
| 98 | \"Installation of Valves - Gate valve, SW, CS, 25NB, as per Engineering Specification 25ES205 / 10.The rate covers all works required to install all on-line items like valves, control valves, safety valves, flowmeters, steam taps etc. in the piping at all elevations. The work shall include transporatation from owners storage point. handling, rigging, lifting, placing & final alignment of valves in to their Respective positions & orientation to suit operationg conditions. The rate is applicable for all matls, types & rating. Werlding and making of flanged connections are excluded from this rate and they will be paid as per schedule A & B.2Also included under this items shall be any work required to ensure the initial satisfactory operation of the valve including minor gland/plud adjustments, lubrication and minor adjustments to the operationg mechanism. After erection in place, the valves shall be fully opened and then, after ensuring free movement, shall be closed.The pay quantity shall be the no of items installed.\" |
| 99 | \"Installation of Valves - Gate Valve, SW, CS, 25NB, as per Engineering Specification 25ES205 / 10.The rate covers all works required to install all on-line items like valves, control valves, safety valves, flowmeters, steam taps etc. in the piping at all elevations. The work shall include transporatation from owners storage point. handling, rigging, lifting, placing & final alignment of valves in to their Respective positions & orientation to suit operationg conditions. The rate is applicable for all matls, types & rating. Werlding and making of flanged connections are excluded from this rate and they will be paid as per schedule A & B.2Also included under this items shall be any work required to ensure the initial satisfactory operation of the valve including minor gland/plud adjustments, lubrication and minor adjustments to the operationg mechanism. After erection in place, the valves shall be fully opened and then, after ensuring free movement, shall be closed.The pay quantity shall be the no of items installed.\" |
| 100 | \"Radiographic Inspection of the weld joints shall be conducted as per the code, specs and Engineering Specification 25ES205 / 10. Drawings & instruction of the Engineer-in-charge. However the extent of inspection (%) shall be as per attached document REF:25ES205The rate quoted shall be inclusive of all operations necessary to fulfill the work of radiography (x-ray / gamma ray) tests including all tools / tackles, films, chemicals etc. complete. After testing, if any joint is found defective, the same shall be rectified and re-tested free of cost. The pay quantity shall be linear centimeters of weld successfully passed.\" |
| 101 | \"DP/MP Test of the weld joints shall be conducted as per the code, specs and Engineering Specification 25ES205 / 10. Drawings & instruction of the Engineer-in-charge. However the extent of inspection (%) shall be as per attached document REF:25ES205The rate quoted shall be inclusive of all operations necessary to fulfill the work of DP/MP tests including all tools / tackles, films, chemicals etc. complete. After testing, if any joint is found defective, the same shall be rectified and re-tested free of cost. The pay quantity shall be linear centimeters of weld successfully passed.\" |
| 102 | \"Fabrication and Erection of Structural SupportsSupply of material, transportation, cutting, edge preparation drilling, threading, welding and fixing of structurals supports at all elevations and chipping and grouting as required and clamping /bottling/fixing of pipeline (including the cost of sand, cement, MS plates ,chemical bolts & Structurals) as per Engineering Specification 25ES205 / 10.\" |
| 103 | \"Supply and installation of C1 Resting cradle as per Engineering Specification 25ES205 / 10.Transportation from owner’s store, installation etc. are included.Fabrication of supports including supply of materials. Actual quantity based on approved for construction drawing. Refer attached support standard for details.\" |
| 104 | \"Supply and installation of C4 Guide Cradle as per Engineering Specification 25ES205 / 10.Transportation from owner’s store, installation etc. are included.Fabrication of supports including supply of materials. Actual quantity based on approved for construction drawing. Refer attached support standard for details.\" |
| 105 | \"Supply and installation ofD1S5 Directional stopper shoe including stopper as per Engineering Specification 25ES205 / 10.Transportation from owner’s store, installation etc. are included.Fabrication of supports including supply of materials. Actual quantity based on approved for construction drawing. Refer attached support standard for details.\" |
| 106 | \"Supply and installation of S1 resting shoe as per Engineering Specification 25ES205 / 10.Transportation from owner’s store, installation etc. are included.Fabrication of supports including supply of materials. Actual quantity based on approved for construction drawing. Refer attached support standard for details.\" |
| 107 | \"Supply and installation of S1 Guide shoe as per Engineering Specification 25ES205 / 10.Transportation from owner’s store, installation etc. are included.Fabrication of supports including supply of materials. Actual quantity based on approved for construction drawing. Refer attached support standard for details.\" |
| 108 | \"Supply and installation of G1 bare pipe guide as per Engineering Specification 25ES205 / 10.Transportation from owner’s store, installation etc. are included.Fabrication of supports including supply of materials. Actual quantity based on approved for construction drawing. Refer attached support standard for details.\" |
| 109 | \"Painting - 80NB pipeline ( insulated line:only primer, refer painting spec.), as per Engineering Specification 02ES023/2010.The unit of measurement for Painting of pipeline shall be Running Meters along centreline (includes all on line fittings, valves & instr. tapping up to first isolation) and number of markings (Markings includes2M long ground color, Color Band(s), Line identification no. & Flow direction arrow).For painting the Marking on insulated, SS, Gl and Cl lines, the unit shall be Per Marking.Painting of pipe supports (includes base springs, Hanger springs, shoes & trunnions and excludes pipe bridge structures, platforms, eqpt. support structures & such structures which does not actually support the pipeline) forms part of the pipeline and no separate payment shall be made.\" |
| 110 | \"Painting - 80NB pipeline, as per Engineering Specification 02ES023/2010.The unit of measurement for Painting of pipeline shall be Running Meters along centreline (includes all on line fittings, valves & instr. tapping up to first isolation) and number of markings (Markings includes2M long ground color, Color Band(s), Line identification no. & Flow direction arrow).For painting the Marking on insulated, SS, Gl and Cl lines, the unit shall be Per Marking.Painting of pipe supports (includes base springs, Hanger springs, shoes & trunnions and excludes pipe bridge structures, platforms, eqpt. support structures & such structures which does not actually support the pipeline) forms part of the pipeline and no separate payment shall be made.\" |
| 111 | \"Painting - 50NB pipeline ( insulated line:only primer, refer painting spec.), as per Engineering Specification 02ES023/2010.The unit of measurement for Painting of pipeline shall be Running Meters along centreline (includes all on line fittings, valves & instr. tapping up to first isolation) and number of markings (Markings includes2M long ground color, Color Band(s), Line identification no. & Flow direction arrow).For painting the Marking on insulated, SS, Gl and Cl lines, the unit shall be Per Marking.Painting of pipe supports (includes base springs, Hanger springs, shoes & trunnions and excludes pipe bridge structures, platforms, eqpt. support structures & such structures which does not actually support the pipeline) forms part of the pipeline and no separate payment shall be made.\" |
| 112 | \"Painting - 50NB pipeline (insulated line:only primer, refer painting spec.), as per Engineering Specification 02ES023/2010.The unit of measurement for Painting of pipeline shall be Running Meters along centreline (includes all on line fittings, valves & instr. tapping up to first isolation) and number of markings (Markings includes 2M long ground color, Color Band(s), Line identification no. & Flow direction arrow).For painting the Marking on insulated, SS, Gl and Cl lines, the unit shall be Per Marking.Painting of pipe supports (includes base springs, Hanger springs, shoes & trunnions and excludes pipe bridge structures, platforms, eqpt. support structures & such structures which does not actually support the pipeline) forms part of the pipeline and no separate payment shall be made.\" |
| 113 | \"Painting - 25NB pipeline, as per Engineering Specification 02ES023/2010.The unit of measurement for Painting of pipeline shall be Running Meters along centreline (includes all on line fittings, valves & instr. tapping up to first isolation) and number of markings (Markings includes2M long ground color, Color Band(s), Line identification no. & Flow direction arrow).For painting the Marking on insulated, SS, Gl and Cl lines, the unit shall be Per Marking.Painting of pipe supports (includes base springs, Hanger springs, shoes & trunnions and excludes pipe bridge structures, platforms, eqpt. support structures & such structures which does not actually support the pipeline) forms part of the pipeline and no separate payment shall be made.\" |
| 114 | \"Painting markings – 80NB, as per Engineering Specification 02ES023/2010.The unit of measurement for Painting of pipeline shall be Running Meters along centreline (includes all on line fittings, valves & instr. tapping up to first isolation) and number of markings (Markings includes2M long ground color, Color Band(s), Line identification no. & Flow direction arrow).For painting the Marking on insulated, SS, Gl and Cl lines, the unit shall be Per Marking.Painting of pipe supports (includes base springs, Hanger springs, shoes & trunnions and excludes pipe bridge structures, platforms, eqpt. support structures & such structures which does not actually support the pipeline) forms part of the pipeline and no separate payment shall be made.\" |
| 115 | Paint markings – 50NB, as per Engineering Specification 02ES023/2010.The unit of measurement for Painting of pipeline shall be Running Meters along centreline (includes all on line fittings, valves & instr. tapping up to first isolation) and number of markings (Markings includes 2M long ground color, Color Band(s), Line identification no. & Flow direction arrow).For painting the Marking on insulated, SS, Gl and Cl lines, the unit shall be Per Marking.Painting of pipe supports (includes base springs, Hanger springs, shoes & trunnions and excludes pipe bridge structures, platforms, eqpt. support structures & such structures which does not actually support the pipeline) forms part of the pipeline and no separate payment shall be made.\" |
| 116 | \"Cold Insulation (IC) - 80NB Line size, 80mm thk, as per Engineering Specification 02ES042/2010.Running metres thru centerline ( includes all on-line pipe fittings, valve lengths and instrument tappings up to first isolation valve ). Any on-line reducer shall be included in the higher size. For branches, the measurement shall be from surface of bigger / main pipe.\" |
| 117 | \"Hot Insulation (IH) - 80NB Line size, 50mm thk, as per Engineering Specification 02ES029/2010.Running metres thru centerline ( includes all on-line pipe fittings, valve lengths and instrument tappings up to first isolation valve ). Any on-line reducer shall be included in the higher size. For branches, the measurement shall be from surface of bigger / main pipe.\" |
| 118 | \"Hot Insulation (IH) - 50NB/25NB Line size, 40mm thk, as per Engineering Specification 02ES029/2010.Running metres thru centerline ( includes all on-line pipe fittings, valve lengths and instrument tappings up to first isolation valve ). Any on-line reducer shall be included in the higher size. For branches, the measurement shall be from surface of bigger / main pipe.\" |
| 119 | \"Cold Insulation (IC) - Flange joints, 80NB line size, 80mm thk, as per Engineering Specification 02ES042/2010.Pipelines : Running metres thru centerline (includes all on-line pipe fittings, valve lengths and instrument tappings up to first isolation valve). Any on-line reducer shall be included in the higher size. For branches, the measurement shall be from surface of bigger / main pipe.Flanges : No. of boxes (one box per flange joint)Valves : Per valve in nos.\" |
| 120 | \"Hot Insulation (IH) - Flange joints, 80NB line size, 50mm thk, as per Engineering Specification 02ES029/2010.Pipelines : Running metres thru centerline (includes all on-line pipe fittings, valve lengths and instrument tappings up to first isolation valve). Any on-line reducer shall be included in the higher size. For branches, the measurement shall be from surface of bigger / main pipe.Flanges : No. of boxes (one box per flange joint)Valves : Per valve in nos.\" |
| 121 | \"Hot Insulation (IH) - Flange joints, 50NB line size, 40mm thk as per Engineering Specification 02ES029/2010.Pipelines : Running metres thru centerline (includes all on-line pipe fittings, valve lengths and instrument tappings up to first isolation valve). Any on-line reducer shall be included in the higher size. For branches, the measurement shall be from surface of bigger / main pipe.Flanges : No. of boxes (one box per flange joint)Valves : Per valve in nos.\" |
| 122 | \"Cold Insulation (IC) - Flanged valves, 80NB line size, 80mm thk, as per Engineering Specification 02ES042/2010.Pipelines : Running metres thru centerline (includes all on-line pipe fittings, valve lengths and instrument tappings up to first isolation valve). Any on-line reducer shall be included in the higher size. For branches, the measurement shall be from surface of bigger / main pipe.Flanges : No. of boxes (one box per flange joint)Valves : Per valve in nos.\" |
| 123 | \"Hot Insulation (IH) - Flanged valves, 50NB line size, 50mm thk, as per Engineering Specification 02ES029/2010.Pipelines : Running metres thru centerline (includes all on-line pipe fittings, valve lengths and instrument tappings up to first isolation valve). Any on-line reducer shall be included in the higher size. For branches, the measurement shall be from surface of bigger / main pipe.Flanges : No. of boxes (one box per flange joint)Valves : Per valve in nos.\" |
AI Tender Summary
Tender Timeline
Jan 11, 2023
11:30 IST
Tender Published
Tender notice published.
CompletedFeb 02, 2023
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedFeb 03, 2023
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender