Tender For Cluster Wise Single Village Water Supply Schemes Under Jal Jeevan Mission Block Nagar Untari Panchayat-Garbandh Hulhula Khurd Haliwanta Kala And Narhi Cluster No-26 Under Drinking Water And Sanitation Division Garhwa For The Year 2022, Garhwa-Jharkhand

TDR : 35694027

Tender Notice
Corrigendum Details
BOQ

Expired

Garhwa , Jharkhand

Tender Brief : Corrigendum : Tender For Cluster Wise Single Village Water Supply Schemes Under Jal Jeevan Mission Block Nagar Untari Panchayat-Garbandh Hulhula Khurd Haliwanta Kala And Narhi Cluster No-26 Under Drinking Water And Sanitation Division Garhwa For The Year 2022

Document Fees
₹ 10000 /-

EMD
₹ 972000.0 /-

Tender Value
₹ 9.71 Crore /-

Submission Date
28-01-2023

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !

Sr No	Corrigendum Date	Corrigendum	Type	New Submission Date
1	16-01-2023	Date Extend	Date	28-01-2023

Name of Work : BOQ forImplementation of Cluster wise Single Village Water Supply Schemes under Jal Jeevan Mission Block - Nagar untari, Panchayat - Garbandh, Hulhula khurd, Haliwanta kala & Narhi (Cluster : 26)under Drinking Water and Sanitation Division, Garhwafor the year 2022-23

Sl. No.	Item Description
1	MODEL-1AWITHOUT SOURCE(No.of Scheme 12 )
2	Solar Photovoltaic (SPV) Solar Submersible D.C. Water Motor Pump
3	Designing, Supplying, Installation, Testing & Commissioning with all tools & Parts of following Solar Photovoltaic (SPV) Solar Submersible D.C. Water Motor Pump Suitable for minimum 125mm x 115mm bore well as per MNRE Guideline with following specifications & accessories.
4	SPV arrays contains specified No of same capacity type & specification modules connected to series or parallel to obtained the required voltage & current the power output of individual PVmodules should be minimum 200 watt peak.
5	i) The SPV modules should be as per IEC-61215 and IEC 61730 part 1.0)
6	ii) All external parts of motor pump used in submersible pump which are in contact of water is stainless steel grade 303 or higher as required.
7	iii) The PV modules shouldbe mounted on metallic structure of adequate strength and appropriate design which can withstand load of modules & High wind pressure up to 200Km/h.
8	iv) The module mounting structure should be hot dip galvanized according to IS 4759.
9	v) To enhance the performance of SPV water pumping system & arrangement for seasonal tilt angle Adjustment should be provided
10	vi) Necessary arrangement should be provided in controller automatic start-run-stop through out the day with water level detection system. (As per MNRE Specification)
11	vii) Necessary protection such as lightening arrestor etc. should be provided to protect the controller & SPV
12	viii) The suction/delivery pipe shall be UPVC / H.D.P.E. pipes of appropriate size 60m or more as required minimum pressure rating of 8kg/Sq cm- PE 100 grade for pump up to 3HP & 10 Kg/Sq cm- PE 100 grade for 5 HP.
13	ix) All cable used shall be as per IS 694. Suitable size of cable shall be used in sufficient length for inter connection between the SPV array to SPV controller and SPV controller to solar power pump. Provision of cable shall be as per IS 14536.
14	x) The motor pump set should have a 5 years warranty.
15	xi) Control panel suitable for motor pump with arrangement of dry run & over flow protection sensor, float switch & rain prevention box. (As per MNRE Specification)
16	xii) The SPV controller must have IP-65 protection or must be housed in cabinet having at least IP-65 protection.
17	xiii) The system should be as per MNRE guide line & Eco-friendly with suitable arrangement to operate new pump manually.
18	xiv) With third party inspection before dispatch.
19	xv) Fitting, fixing & mounting on water tank steel structure.
20	xvi) Provision for web basedremote monitoring of the pumps to be installed must be made through the inbuilt controllers . It should be possible to ascertain the daily water output, the power generated by PV Array ,the Up and downtime of the pump during the year, number of days the pump was unused or under breakdown repairs.
21	The following details should be marked indelibly on the motor pump set
22	a) Name of the Manufacturer or Distinctive Logo.
23	b) Model Number.
24	c) Serial Number.
25	Solar submersible motor pump (SPV DC Type)
26	i) 1 HP (DC Pump) with 900 WP minimum watt P.V. Panel as MNRE pump head Max Shut-off head up to 120 mtrs. For higher or lower head or in between various modules output could be decided on prorates basis. (As per latest guide line of MNRE)
27	Carrying out recuperation/Yield Test for ascertaining the discharge of constructed well/ excavated profile as directed by the IEC. The testout by the drawing down water from the well/ profile below normal/subsoil water level up to full depth rise is recorded the normal water level/subsoil water level in the well / profile as well as strainer/level at pump as per design of W.S. scheme shall be recorded prior to the test including cost of all materials, over Load , Labours etc. complete as directed.
28	Supplying all labours, tools and equipments for dismantling of head & water tank assembly and taking out 32 mm dia old G.I. Pipe, connecting rod, cylinder assembly the dismantled components after necessary changing for making the T/W in good condition with all transportation including unused taken out materials back in store all complete job as per direction of E/I.
29	Provision of solar night lamp.
30	Construction RCC Foundation for Steel structurestaging& Solar panel
31	Earth work in excavation in foundation trenches in ordinary soil and disposal of excavated earth as obtained to a distance up to 50.0m ,including all lifts, levelling ,ramming the foundation trenches, removing roots of trees, shrubs all complete as per approved design ,building specification and direction of E/I (vide classification of soil item -B)
32	Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials ,labour ,royalty and taxes all complete as per building specification and direction of E/I(Mode of measurement compacted volume)
33	Providing brick Flat soling
34	Providing PCC M-150 in nominal mix of (1:2:4) in foundationwith approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M.2.5to 3 including screening shuttering mixing cement concrete in mixer and placing in position vibrating striking curing and royalty all complete as per building specification and direction of E/I
35	Providing RCC M-200 in nominal mix of (1:1.5:3) in columnswith approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M.2.5to 3 including screening shuttering mixing cement concrete in mixer and placing in position vibrating striking curing and royalty all complete as per building specification and direction of E/I.
36	(a)Foundation for Steel structure staging
37	Footing
38	Vertical Pedestal
39	Tie Beam
40	Providing for steel reinforcement as per approved design and drawing excluding carriage of T.S. bar to work site cutting, bending with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/I.
41	Carriage of construction materials to work site including loading, unloading & stacking etc. all complete.
42	Cement10KM lead
43	Sand 36KM lead
44	Stone chips11KM lead
45	Construction ofgalvanized tubular Steel structure staging for (4.5m) HDPE water storage Tank& Solar Panel.
46	Providing structural steel galvanised tubular hollow section work in trusses, other similar trussed purlins and members with all bracing ,gusset plates etc as per detailed design and drawing or as directed by Engineer- in-charge ,including cutting fabricating ,hoisting , erecting and fixing in position , making riveted/bolted /welded connections and one coat of anticorrosive paint and over it two coat of all oil painting & For Structure(PLUS) Providing and applying materials &labour for hot dip galvanizing of above structure including transportation for galvanizing minimum thickness 80microns (Net wt. of components to be Galv) preferably TATA structural section etc complete.
47	Providing structural steel work in trusses other similar trussed purlins and members with bracing gusset plates etc as per detailed design and drawing or as directed by Engineer- in-charge including cutting fabricating hoisting erecting and fixing in position making reverted bolted welded connections one coat of anticorrosive paint and over it two coats of oil painting etc complete.
48	Materials and labour for vinyl painting of matter given by department in different color
49	Installation of 2000 liters Capacity Water Storage Tank
50	Providing and fixing HDPE container Syntex or alike one piecemolded water tank made out of low density polythyler andbuilt corrugation including of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow of all tanks capacity 2000.00 litres Capacity Water storage Tank
51	Transportation Charge
52	Lifting of 2000 Litrs Capacity Tank up to 4.5m height with lifting tools with rope and labour
53	Making hole in Tank
54	Making long screw in G.I. pipe including supplying and fitting jam nuts and extra socket etc.
55	Rising and Distribution Network with House Connection up to 10 Nos. including Platform & Stand post
56	Earth work in excavation in foundation trenches in hard soil (Vide Classification soil item B) and disposal of excavated earth as obtained to a distance up to 50 Mtr. including all lifts, leveling, ramming the foundation trenches, removing roots of trees, shrubs all complete as per approved design, specification and direction of E/I.
57	Dismantling plain cement concrete work including stacking serviceable materials in countable stacks within 15 M lead and disposal of unserviceable materials with all leads all complete.
58	Providing PCCM-200 with nominal mix of (1:1.5:3) with approved quality of stone chips 20 mm to 6 mm size graded and clean coarse sand of FM 2.5 to 3.0 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, sticking, curing , taxes and royalty all complete as per specification and direction of E/I. for construction of road cutting portion.
59	Rising Main
60	Manufacture, supply and Delivery offollowing Nominal dia UPVC column pipes including PVC socket (Coupler),
61	65mm dia -Density of pipe 1.38 to 1.43 Gm per Cm3 OD:74.5 to 75.2mm wall Thickness End:9mm to 10.7mm, Barrel 9mm to 10.7 mm, Length: 3Mtrs.Rising main
62	50 mm dia -Density of pipe 1.38 to 1.43 Gm per Cm3 OD:87.5 to 88.2mm wall Thickness End:9 .8 mm to 11.9mm, Barrel 7.3mm to 9 mm, Length: 3Mtrs. Delivery Pipe
63	Distribution Main
64	Providing and supplying High Density Polyethylene pipe (HDPE pipe) of 20 mm to 225 mm OD and pressure 6.0 Kg/cm2 and 10 Kg/cm2 suitable for water supply which is available in all standard conforming to ISI -- 4984/14151/12786/13488,ISO 4427 , DIN-8074materials rates are Ex-factory excluding transportation, taxes and duties. PE-80 , PN- 10.
65	63 mm HDPE Pipe
66	50 mm HDPE Pipe
67	32 mm HDPE Pipe-
68	20 mm HDPE Pipe-
69	Providing and fixing Gun Metal Gate valvewith C I wheel of approved quality (screwed end).
70	65 mm dia
71	50 mm dia .
72	Providing and supplying High Density Polyethylene(HDPE )fittings of 20 mm to 225 mm OD and pressure 6.0 Kg/cm2 and 10 Kg/cm2 suitable for water supply which is available in all standard conforming to ISI -- 4984/14151/12786/13488,ISO 4427 , DIN-8074materials rates are Ex-factory excluding transportation, taxes and duties.
73	Lowering, Laying and Jointing H. D. P. E./M. D.P. E. pipes in proper position including all specials by compression fitting/electro fusion and butt fusion jointing procedure as per relevant IS Code complete with all materials for jointing procedure like Electro fusion machine, Electric heater/butt fusion welding machine with hydraulic jack, top loading clamp etc. and all labours as directed by engineer in charge as per IS-7634 Part II.
74	For Rising
75	65 mm HDPE Pipe
76	50 mm HDPE Pipe
77	For Distribution
78	65 mm HDPE Pipe
79	50 mm HDPE Pipe
80	32 mm HDPE Pipe
81	20 mm HDPE Pipe
82	15 mm Dia GI Pipe
83	Supplying all materials , labour and tools for fixing 15 mm dia G.I. pipes with Red lead and yarn of following nominal bore with screwed and socketed joints on wall, ceiling and floor including supplying and fitting of wall hooks or pipe clamps, wooden plugs, cutting pipes to size and threading ends if required etc. all complete as per specification and direction of Engineer-in-Charge.
84	Supplying and fixing G.I. fittings of approved make all complete as per specification and direction of E/I.
85	Elbow 15 mm dia.
86	Reducer Socket 20x15 mm dia.
87	Nipple 15 mm dia.
88	Plain Socket 15 mm dia.
89	Supplying and fixing G.M. ferrule of approved make in existing C.I./D.I. main Including drilling and taping C.I./D.I. main all complete as per specification and direction of E/I. 3 mm, 6 mm 10 mm dm ferrule weight not less than 425 gram.
90	Providing and fixing Gun Metal full way valve of approved quality, all complete, as per specification and direction of E/I.
91	65 mm dia Full way valve
92	50 mm dia and weight not less than 1.5 Kg.
93	Providing and fixing of male ended C.I.Body brass spindle valve and seat Bib cock of approved quality with extra socketall complete as per specification and direction of E/I.
94	15 dia and weight not less than 400 Gm
95	Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design.With common burnt clay F.P.S.(non modular) bricks of class designation 7.5.
96	Full way valve chamber
97	Supplying materials , labours and equipment\"s for construction of 0.90M x 0.90 M size P.C.C. (1:2:4) Rectangular Platform with stand post in house including 12 mm thick cement plaster in C.M. (1:4) with neat cement punning over exposed surfaceall complete job, as per approved design, specification and direction of E/I.
98	Providing brick masonry chamber ofinner size 600 x 600 x 450 mm deep for bore well protection having 125 mm thick wall and 75 mm R.C.C cover including cement plaster of exposed surface, etc all complete job.
99	Earth work in back filling the trenches after laying different types and size of pipes with earth removed during excavation within initial lead and lift as per specification and direction of Engineer-in-Charge.
100	Providing fitting & fixing 32 mm to 50 mm service HDPE saddleall complete job, as per approved design, specification and direction of E/I.
101	Carriage of materials from different sources or departmental stores to work site including loading, transporting, unloading and stacking the materials at work site etc. all complete job. as per direction of E/I.
102	Cement Lead 10 Km (avg.)
103	Sand Lead 36 Km (avg.)
104	Stone Chips Lead 11 Km (avg.)
105	Steel ReinforCement Lead 10 Km (avg.)
106	Bricks Lead 06 Km (avg.)
107	Annual Operation & Maintenance cost based on Existing D/T Well with solarmotor pump for 5 years
108	O & M Cost for 1st year
109	O & M Cost for 2nd year
110	O & M cost for 3rd Year
111	O & M cost for 4th Year
112	O & M cost for 5th Year
113	Provision of one no SIM card & its recharging cost for RMC
114	MODEL-1B WITH SOURCE (Drilled T/W 125/115dia mm, 60M Deep)(49 Nos)
115	Tube Well
116	Drilling Portion
117	Construction for 115/125 mm dia drilled Tube-Well for drilling in all kinds of soil rock for installation of hand pump with D.T.H Rig machine all complete including supplying all materials, labours, tools, drilling, rigs, air compressor and equipments as well as fuel lubricant for making 125/115 mm dia boring etcand cost of transporting rig machine and other vehicle up to site workas per specification and direction of Engineer-in-charge.
118	(a) Up to 30mtr. Depth bellow G.L. in Rural Areas
119	(b) Beyond 30mtr.In Rural Areas
120	Providing all equipments and labour for lowering 125mm dia blue UPVC Casing pipe as casing for protecting the side from falling during the process of drilling all complete job including carriage of material to work site.
121	Supplying labour cement and calcium chloride or bentonite solution and equipments for Grouting to Casing Pipe all complete job including carriage of material to work site as per specification & direction of E/I
122	Supplying all tools, equipments and labour and doing washing, flushing and development of drilled tube well to give clean and clear water all complete as per direction E/I.
123	Supplying all materials labours and equipment including 125 mm dia GI/CI cap 125 mm dia T/W properly all complete and taking it out as per specification & direction of E/I. (the cap will be property of department)
124	Civil Portion
125	Supplying all tools, equipment, labours and lowering 32 mm dia G.I. (Medium)pipe in DT in 3 mtr. Length all complete job as per direction of E/I. Including carriage of materials.
126	Supplying all tools, Labour for fitting and fixing deep well cylinder with necessary connecting rod all complete job as per specification & direction of E/I.
127	Supplying all materials, labours for fitting and fixing of India Mark II Hand Pump with all accessories all job complete as per direction of E/I. Including carriage of materials.
128	Supplying all materials, labours and equipment for constructing PCC (1:2:4) circular platform around each drilled tube well including 12mm thick cement plaster (1:4) with neat cement punning over exposed surface as per UNICEF design etc. all complete. Including carriage of materials.
129	Supplying all materials labour and equipment for constructing PCC (1:2:4) drain as per UNICEF Design etc. all complete .Including carriage of materials.
130	Add Extra Item for Supplying tools, labours and materials for painting, numbering and year for construction of T/Well and taking of colour photograph with two or three nearest persons including platform, drain, soak pit and also longitude & latitude, details of T/W such as total depth, casing depth, static water level, drawdown, discharge, strata chart, beneficiary population etc in separate sheet/format all complete as per direction of E/I.
131	COST OF MATERIALS
132	cost of standard I.S.I. mark Deep Well Hand Pump for India mark-II, I.S.I. 15500 (Part 2) / 2004 with latest revision including 12mm x 3 meter long 8 no. Connecting Rods made of bright bar electro-galvanized fitted with coupler & normal stand assembly recommended for use with cylinder assembly suitable for bore wellcasing pipe.
133	Cost of 32 mm dia GI pipe (Medium) 3 Mtrs long screwed at both ends with seamless socket as per IS:1239(Part 1990).
134	Cost of 125 mm dia blue UPVC Casing Pipe as per I.S.12818/2016 CML no.- 5543459
135	RCC Foundation for Steel structurestaging& Solar panel
136	Earth work in excavation in foundation trenches in ordinary soil and disposal of excavated earth as obtained to a distance up to 50.0m ,including all lifts, levelling ,ramming the foundation trenches, removing roots of trees, shrubs all complete as per approved design ,building specification and direction of E/I(vide classification of soil item -B)
137	Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials ,labour ,royalty and taxes all complete as per building specification and direction of E/I
138	Providing designation 75 A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I
139	Providing nominal mix PCC of (1:4:8) in foundationwith approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M.2.5to 3 including screening shuttering mixing cement concrete in mixer and placing in position vibrating striking curing and royalty all complete as per building specification and direction of E/I
140	Providing RCC M-20 in nominal mix of (1:1.5:3) in columnswith approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M.2.5to 3 including screening shuttering mixing cement concrete in mixer and placing in position vibrating striking curing and royalty all complete as per building specification and direction of E/I.
141	(a)Foundation for Steel structure staging
142	Footing and Vertical Pedestal Raft
143	Column
144	Tie Beam
145	(b)Foundation for Solar panel
146	Footing
147	Vertical Pedestal
148	Providing for steel reinforcement as per approved design and drawing excluding carriage of T.S. bar to work site cutting, bending with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/I.
149	(a) Foundation for Steel structure staging
150	Carriage of materials from different sources or departmental stores to work site including loading, transporting, unloading and stacking the materials at work site etc. all complete job. as per direction of E/I.
151	Cement Lead 10 Km (avg.)
152	Sand Lead 36 Km (avg.)
153	Stone Chips Lead 11 Km (avg.)
154	Steel Reinforcement Lead 10 Km (avg.)
155	Bricks Lead 06 Km (avg.)
156	Galvanized tubular Steel structure staging forHDPE water storage Tank& Solar Panel
157	Providing structural steel galvanisedsqure pipe section work in trusses, other similar trussed purlins and members with all bracing ,gusset plates etc as per detailed design and drawing or as directed by Engineer- in-charge ,including cutting fabricating ,hoisting , erecting and fixing in position , making riveted/bolted /welded connections and one coat of anticorrosive paint and over it two coat of all oil painting & For Structure(PLUS) Providing and applying materials &labour for hot dip galvanizing of above structure including transportation for galvanizing minimum thickness 80microns (Net wt. of components to be Galv) preferably TATA structural section etc complete.
158	HARDWARE (L.S.)
159	Information board for IEC
160	Providing structural steel work in trusses other similar trussed purlins and members with bracing gusset plates etc as per detailed design and drawing or as directed by Engineer- in-charge including cutting fabricating hoisting erecting and fixing in position making reverted bolted welded connections one coat of anticorrosive paint and over it two coats of oil painting etc complete
161	Installation of 5000 liters Capacity Water Storage Tank
162	Providing and fixing HDPE container Syntex or alike one piecemolded water tank made out of low density polythyler andbuilt corrugation including of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow of all tanks capacity 5000.00 litres Capacity Water storage Tank
163	Transportation Charge
164	Lifting of 5000 Litrs Capacity Tank up to 4.00m height with lifting tools with rope and labour
165	Making hole in Tank
166	Making long screw in G.I. pipe including supplying and fitting jam nuts and extra socket etc.
167	Rising and Distribution Network with House Connection up to 20 Nos. including Platform & Stand post
168	Earth work in excavation in foundation trenches in hard soil (Vide Classification soil item B) and disposal of excavated earth as obtained to a distance up to 50 Mtr. including all lifts, leveling, ramming the foundation trenches, removing roots of trees, shrubs all complete as per approved design, specification and direction of E/I.
169	Dismantling plain cement concrete work including stacking serviceable materials in countable stacks within 15 M lead and disposal of unserviceable materials with all leads all complete
170	Providing PCCM-200 with nominal mix of (1:1.5:3) with approved quality of stone chips 20 mm to 6 mm size graded and clean coarse sand of FM 2.5 to 3.0 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, sticking, curing , taxes and royalty all complete as per specification and direction of E/I. for construction of road cutting portion
171	Rising Main
172	Manufacture, supply and Delivery offollowing Nominal dia UPVC column pipes including PVC socket (Coupler),
173	65mm dia -Density of pipe 1.38 to 1.43 Gm per Cm3 OD:74.5 to 75.2mm wall Thickness End:9mm to 10.7mm, Barrel 9mm to 10.7 mm, Length: 3Mtrs.Rising main
174	50 mm dia -Density of pipe 1.38 to 1.43 Gm per Cm3 OD:87.5 to 88.2mm wall Thickness End:9 .8 mm to 11.9mm, Barrel 7.3mm to 9 mm, Length: 3Mtrs. Delivery Pipe
175	Distribution
176	Providing and supplying High Density Polyethylene pipe (HDPE pipe) of 20 mm to 225 mm OD and pressure 6.0 Kg/cm2 and 10 Kg/cm2 suitable for water supply which is available in all standard conforming to ISI -- 4984/14151/12786/13488,ISO 4427 , DIN-8074materials rates are Ex-factory excluding transportation, taxes and duties.
177	63 mm HDPE Pipe
178	50 mm HDPE Pipe
179	32 mm HDPE Pipe
180	20 mm HDPE Pipe
181	Providing and fixing Gun Metal Gate valvewith C I wheel of approved quality(screwed end).
182	65 mm dia
183	50mm dia
184	Providing and supplying High Density Polyethylene(HDPE )fittings of 20 mm to 225 mm OD and pressure 6.0 Kg/cm2 and 10 Kg/cm2 suitable for water supply which is available in all standard conforming to ISI -- 4984/14151/12786/13488,ISO 4427 , DIN-8074materials rates are Ex-factory excluding transportation, taxes and duties.
185	Lowering, Laying and Jointing H. D. P. E./M. D.P. E. pipes in proper position including all specials by compression fitting/electro fusion and butt fusion jointing procedure as per relevant IS Code complete with all materials for jointing procedure like Electro fusion machine, Electric heater/butt fusion welding machine with hydraulic jack, top loading clamp etc. and all labours as directed by engineer in charge as per IS-7634 Part II.
186	For Rising
187	50 mm HDPE Pipe
188	65 mm HDPE Pipe
189	Distribution
190	65 mm HDPE Pipe
191	50 mm HDPE Pipe
192	32 mm HDPE Pipe
193	20 mm HDPE Pipe
194	Providing 15 mm dia. G.I. pipe Tata or equivalent make as per IS 1239 (Part 1/2004) ISI Mark /medium quality in Stand Post.
195	Supplying all materials , labour and tools for fixing 15 mm dia G.I. pipes with Red lead and yarn of following nominal bore with screwed and socketed joints on wall, ceiling and floor including supplying and fitting of wall hooks or pipe clamps, wooden plugs, cutting pipes to size and threading ends if required etc. all complete as per specification and direction of Engineer-in-Charge.
196	Supplying and fixing G.I. fittings of approved make all complete as per specification and direction of E/I.
197	Elbow 15 mm dia.
198	Reducer Socket 20x15 mm dia.
199	Nipple 15 mm dia.
200	Plain Socket 15 mm dia.
201	Supplying and fixing G.M. ferrule of approved make in existing C.I./D.I. main Including drilling and taping C.I./D.I. main all complete as per specification and direction of E/I. 3 mm, 6 mm 10 mm dm ferrule weight not less than 425 gram.
202	Providing and fixing Gun Metal full way valve of approved quality, all complete, as per specification and direction of E/I.
203	65 mm dia Full way valve
204	50 mm dia and weight not less than 1.5 Kg.
205	Providing and fixing of male ended C.I.Body brass spindle valve and seat Bib cock of approved quality with extra socketall complete as per specification and direction of E/I.
206	15 dia and weight not less than 400 Gm
207	Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design.With common burnt clay F.P.S.(non modular) bricks of class designation 7.5. Full way valve chamber
208	Supplying materials , labours and equipment\"s for construction of 0.90M x 0.90 M size P.C.C. (1:2:4) Rectangular Platform with stand post in house including 12 mm thick cement plaster in C.M. (1:4) with neat cement punning over exposed surfaceall complete job, as per approved design, specification and direction of E/I.
209	Providing brick masonry chamber ofinner size 600 x 600 x 450 mm deep for bore well protection having 125 mm thick wall and 75 mm R.C.C cover including cement plaster of exposed surface, etc all complete job
210	Earth work in back filling the trenches after laying different types and size of pipes with earth removed during excavation within initial lead and lift as per specification and direction of Engineer-in-Charge.
211	Providing fitting & fixing 32 mm to 50 mm service HDPE saddleall complete job, as per approved design, specification and direction of E/I.
212	Carriage of materials from different sources or departmental stores to work site including loading, transporting, unloading and stacking the materials at work site etc. all complete job. as per direction of E/I.
213	Cement Lead 10 Km (avg.)
214	Sand Lead 36 Km (avg.)
215	Stone Chips Lead 11 Km (avg.)
216	Steel ReinforCement Lead 10 Km (avg.)
217	Bricks Lead 06 Km (avg.)
218	Solar Photovoltaic (SPV) Solar Submersible D.C. Water Motor Pump
219	Designing, Supplying, Installation, Testing & Commissioning with all tools & Parts of following Solar Photovoltaic (SPV) Solar Submersible D.C. Water Motor Pump Suitable for minimum 125mm x 115mm bore well as per MNRE Guideline with following specifications & accessories.
220	SPV arrays contains specified No of same capacity type & specification modules connected to series or parallel to obtained the required voltage & current the power output of individual PVmodules should be minimum 200 watt peak.
221	i) The SPV modules should be as per IEC-61215 and IEC 61730 part 1.0)
222	ii) All external parts of motor pump used in submersible pump which are in contact of water is stainless steel grade 303 or higher as required.
223	iii) The PV modules shouldbe mounted on metallic structure of adequate strength and appropriate design which can withstand load of modules & High wind pressure up to 200Km/h.
224	iv) The module mounting structure should be hot dip galvanized according to IS 4759.
225	v) To enhance the performance of SPV water pumping system & arrangement for seasonal tilt angle Adjustment should be provided
226	vi) Necessary arrangement should be provided in controller automatic start-run-stop through out the day with water level detection system. (As per MNRE Specification)
227	vii) Necessary protection such as lightening arrestor etc. should be provided to protect the controller & SPV
228	viii) The suction/delivery pipe shall be UPVC / H.D.P.E. pipes of appropriate size 60m or more as required minimum pressure rating of 8kg/Sq cm- PE 100 grade for pump up to 3HP & 10 Kg/Sq cm- PE 100 grade for 5 HP.
229	ix) All cable used shall be as per IS 694. Suitable size of cable shall be used in sufficient length for inter connection between the SPV array to SPV controller and SPV controller to solar power pump. Provision of cable shall be as per IS 14536.
230	x) The motor pump set should have a 5 years warranty.
231	xi) Control panel suitable for motor pump with arrangement of dry run & over flow protection sensor, float switch & rain prevention box. (As per MNRE Specification)
232	xii) The SPV controller must have IP-65 protection or must be housed in cabinet having at least IP-65 protection.
233	xiii) The system should be as per MNRE guide line & Eco-friendly with suitable arrangement to operate new pump manually.
234	xiv) With third party inspection before dispatch.
235	xv) Provision for web basedremote monitoring of the pumps to be installed must be made through the inbuilt controllers . It should be possible to ascertain the daily water output, the power generated by PV Array ,the Up and downtime of the pump during the year, number of days the pump was unused or under breakdown repairs.
236	The following details should be marked indelibly on the motor pump set
237	a) Name of the Manufacturer or Distinctive Logo.
238	b) Model Number.
239	c) Serial Number.
240	Solar submersible motor pump (SPV DC Type)
241	i) 1 HP (DC Pump) with 900 WP minimum watt P.V. Panel as MNRE pump head Max Shut-off head up to 120 mtrs. For higher or lower head or in between various modules output could be decided on prorates basis. (As per latest guide line of MNRE)
242	Carrying out recuperation/Yield Test for ascertaining the discharge of constructed well/ excavated profile as directed by the IEC. The testout by the drawing down water from the well/ profile below normal/subsoil water level up to full depth rise is recorded the normal water level/subsoil water level in the well / profile as well as strainer/level at pump as per design of W.S. scheme shall be recorded prior to the test including cost of all materials, over Load , Labours etc. complete as directed.
243	Supplying all labours, tools and equipments for dismantling of head & water tank assembly and taking out 32 mm dia old G.I. Pipe, connecting rod, cylinder assembly the dismantled components after necessary changing for making the T/W in good condition with all transportation including unused taken out materials back in store all complete job as per direction of E/I.(As per Model Estimate of Solar Energy based Mini WSS. TS done by SE, Ranchi Circle & Circle Gumla dt. 21.05.2019)
244	Provision of solar night lamp.
245	Galvanised Chain-line mess Fencing around Solar Panel where bore well is away from tower
246	Annual Operation & Maintenance cost based on Existing D/T Well with solarmotor pump for 5 years
247	O & M Cost for 1st year (Excluding Repair Charges)
248	O & M Cost for 2nd year with Annual Repair Charges
249	O & M cost for 3rd Year
250	O & M cost for 4th Year
251	O & M cost for 5th Year
252	Provision of one no SIM card & its recharging cost for RMC
253	MODEL- 02 (8000 LITRE 8 METER STAGING)(42 Nos)
254	Construction of 125 mm x 115 mm x 90.0 M deep Drilled Tube Well
255	Supplying all materials, labour and tools and equipment for drilling 125 x 115 mm dia bore well in any kinds of soil and rocks by using D.T.H. super rig machine and ball hammer technology including all technology inclusive of mobilization, demobilization of rigs air compressor all accessories of rigs tools and plant labour etc. all complete job including transportation charge cost of flushing charge, geographical investigation etc. all complete
256	(a) 0.00m Up to 30.00m depth below G.L. In Rural Areas
257	(b) 30.000m Up to 120.00m depth beyond . In Rural Areas
258	Basic rate of 125mmdia Blue UPVC Casingpipe Confirming to I.S.I . latest revision IS(12818)/2016
259	Supplying all materials, labour and inserting UPVC bluepipe 125 mm internal dia casing pipe for protecting the bore hole in over burden up to hard surface as per IS 12818-1392 with latest revision all complete job with taxesas per specification and direction of E/I.
260	Supplying labour cement and calcium chloride or bentonite solution and equipment’s for grouting Casing pipe
261	Supplying all tools, equipments and labour and doing washing, flushing and development of drilled tube well to give clean and clear water all complete as per direction E/I.
262	Supplying laboursand equipment’s including 125 mm dia G.I. Cap & fittingand fixing over thecasing pipe of bore well properly and taking it out as per direction of E/I.
263	Supplyingmaterials and labours for constructing bore well chamber of 75 B designation brick masonry chamber 600 mm x 450 mm and 750 mm deep internal dimension having 250mm thickness in cement mortar 1:6 including 12mm cement plaster 1:6 with 600 mm x 475 mm RCC cover with earth work in excavation and 75 mm thick PCC (1:3:6) in foundation and refilling all complete as per specification and direction of E/I.
264	2 H.P. D.C. SolarMotor Pump Complete Set
265	Designing, Supplying, Installation, Testing & Commissioning with all tools & Parts of following Solar Photovoltaic (SPV) Solar Submersible D.C. Water Motor Pump Suitable for minimum 125mm x 115mm bore well as per MNRE Guideline with following specifications & accessories.
266	SPV arrays contains specified No of same capacity type & specification modules connected to series or parallel to obtained the required voltage & current the power output of individual PVmodules should be minimum 200 watt peak.
267	i) The SPV modules should be as per IEC-61215 and IEC 61730 part 1.0)
268	ii) All external parts of motor pump used in submersible pump which are in contact of water is stainless steel grade 303 or higher as required.
269	iii) The PV modules shouldbe mounted on metallic structure of adequate strength and appropriate design which can withstand load of modules & High wind pressure up to 200Km/h.
270	iv) The module mounting structure should be hot dip galvanized according to IS 4759.
271	v) To enhance the performance of SPV water pumping system & arrangement for seasonal tilt angle Adjustment should be provided
272	vi) Necessary arrangement should be provided in controller automatic start-run-stop through out the day with water level detection system. (As per MNRE Specification)
273	vii) Necessary protection such as lightening arrestor etc. should be provided to protect the controller & SPV
274	viii) The suction/delivery pipe shall be UPVC / H.D.P.E. pipes of appropriate size 60m or more as required minimum pressure rating of 8kg/Sq cm- PE 100 grade for pump up to 3HP & 10 Kg/Sq cm- PE 100 grade for 5 HP.
275	ix) All cable used shall be as per IS 694. Suitable size of cable shall be used in sufficient length for inter connection between the SPV array to SPV controller and SPV controller to solar power pump. Provision of cable shall be as per IS 14536.
276	x) The motor pump set should have a 5 years warranty.
277	xi) Control panel suitable for motor pump with arrangement of dry run & over flow protection sensor, float switch & rain prevention box. (As per MNRE Specification)
278	xii) The SPV controller must have IP-65 protection or must be housed in cabinet having at least IP-65 protection.
279	xiii) The system should be as per MNRE guide line & Ecofriendly with suitable arrangement to operate new pump manually.
280	xiv) With third party inspection before dispatch.
281	xv) Provision for web basedremote monitoring of the pumps to be installed must be made through the inbuilt controllers . It should be possible to ascertain the daily water output, the power generated by PV Array ,the Up and downtime of the pump during the year, number of days the pump was unused or under breakdown repairs.
282	The following details should be marked indelibly on the motor pump set
283	a) Name of the Manufacturer or Distinctive Logo.
284	b) Model Number.
285	c) Serial Number.
286	Solar submersible motor pump (SPV DC Type)
287	i) 2 HP (DC Pump) with 1800 wp minimum watt P.V. Panel as MNRE pump head Max Shut-off head up to 100 mtrs. For higher or lower head or in between various modules output could be decided on prorates basis. (As per latest guide line of MNRE)
288	Provision of solar night lamp.
289	8000 Litre CapacityR.C.C. Water Tank (2.1 x 2.1 x 2.1 m Internal size) with 8 M staging having Utility Room at Ground Level
290	Earth work in excavation in foundation trenches in ordinary soil (vide classification of soil item-B ) and disposal of excavated earth as obtained to a distance up to 50 m including all lifts,levelling,ramming the foundation trenches, removing roots of trees shrubs all complete as per approved design, building specification and direction of E/I.
291	Providing P.C.C.M-150 in nominal mix of (1:2:4) in foundation with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including screening, mixing cement concrete in mixer and placing in position,vibrating,curing,taxes and royalty all complete as per building specification direction of E/I.
292	Providing and laying in situ Cement concrete of trap/granite/quartzite/ gneiss metal for RCC work in foundation like raft, grillage, strip foundation and footing of RCC columns and steel stanchions including normal dewatering, \"plywood form work, bully/steel propups, compaction, finishing andcuring, etc, complete. (By weigh batching and mix design for M-250only. Use of L & T, A.C.C., Ambuja, Birla Gold, Manikgad, Rajashree, etc. cement is permitted.)
293	Providing and casting in situ Cement Concrete of trap/granite/quartzite/ gneiss metal of approved quality for RCC work as per detailed drawings and designs or as directed by Engineer-in-charge including normal dewatering, centering, \"plywood formwork, bully/steel prop-ups, compaction, finishing the formed surfaces with CM 1:3 of sufficient minimum thickness if special finish is to be provided and curing, etc. complete. (By weigh batching and mix design for M-250 and M-300 only.Use of L&T, A.C. C., Ambuja, Birla Gold, Manikgad, Rajashree, etc. cement is permitted)
294	G.L to above roof of Utility Room
295	Column Utility Room, Roof Beam to Tank beam M-25
296	Column Tank Beam to Tank Roof M-25
297	Providing and casting in situ Cement Concrete of trap/granite/quartzite/ gneiss metal of approved quality for RCC work as per detailed drawings and designs or as directed by Engineer-in-charge including normal dewatering, centering, \"plywood formwork, bully/steel prop-ups, compaction, finishing the formed surfaces with CM 1:3 of sufficient minimum thickness if special finish is to be provided and curing, etc. complete. (By weigh batching and mix design for M-250 and M-300 only. Use of L&T, A.C. C., Ambuja, Birla Gold, Manikgad, Rajashree, etc. cement is permitted)
298	Bracing
299	Beam of Tank Floor
300	Providing and casting in situ Cement Concrete of trap/granite/quartzite/ gneiss metal of approved quality for RCC work as per detailed drawings and designs or as directed by Engineer-in-charge including normal dewatering, centering, \"plywood formwork, bully/steel prop-ups, compaction, finishing the formed surfaces with CM 1:3 of sufficient minimum thickness if special finish is to be provided and curing, etc. complete. (By weigh batching and mix design for M-250 and M-300 only. Use of L&T, A.C. C., Ambuja, Birla Gold, Manikgad, Rajashree, etc. cement is permitted) (excluding M.S, or Tor reinforcement) For RCC M-300 grade Slabs / Landings / Vertical Walls Section-G-Plain and Reinforced Cement Concrete
301	Tank Floor Roof M-30
302	Tank Roof Top M-25
303	Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads including cost of materials,labours,royalityand taxes all complete as per building specification and direction of E/I.(Mode of measurement-compacted volume).
304	Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes royalty all complete as per building specification and direction of E/I.
305	Filling in foundation trenches and plinth in layers not exceeding 150mm thick, well watered,rammed,fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50M and lift of 1.5M all complete as per building specifications and direction of E/I.(Mode of measurement-compacted volume).
306	Providing designation 75 A Brick work in C.M(1:6) in foundation and plinth with approved quality of clean coarse sand of F.M.2 to2.5 including providing 10mm thick mortar joints, cost of screening,scaffolding,raking out joints to 15mm depth,curing,taxes and royalty all complete as per building specification and direction of E/I.
307	Providing designation 75A Brick work in C.M(1:6) in superstructure with approved quality of clean coarse sand of F.M 2 to 2.5 including providing 10mm thick mortar joints, cost of screening,scaffolding,raking out joints 15mm depth,curing,taxes and royalty all complete as per bldg. specification and direction of E/I.
308	Providing R.C.C.M-200 in nominal mix of (1:1.5:3) in lintel with approved quality of stone chips (20mm to 6mm size) graded and clean coarse of F.M 2.5 to 3 including screening, centering, shuttering, mixing cement concrete in mixer and placing in position, vibrating striking, curing(but excluding the cost of reinforcement),taxes and royalty all complete as per building specification and direction of E/I.
309	Providing av.63 mm thick R.C.C M-200 in nominal mix of (1:1.5:3) chhajja with approved quality of stone chips (20mm to 6mm size) graded and clean coarse sand of F.M 2.5 to 3 including in mixer and placing in position,vibrating,striking,6mm cement plaster(1:4) in ceiling and sides of chhajja with sand of F.M 1.5, curing(but excluding the cost of reinforcement) taxes, and royalty all complete as per building specification and direction of E/I.
310	Providing T.M.T steel reinforcement of different dia rods as per approved design and drawing including carriage of M.S bars to work site, cutting bending and binding with annealed wire with cost of wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I.
311	Supplying, fitting and fixing M.S grill made of 20*6 mmM.S flats as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/I.
312	Providing and fixing fan hooks of 16 mm dia M.S.bar & 1 meter long bent to required size and shape, placed in position and fixed in the R.C.C. slab/beam at the time ofcasting all complete as per building specification and direction of E/I.
313	Supplying, fitting and fixing 20 gauge G.C.I sheet gate fitted on M.S angle frame of size60606 mm including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in C/C(1:2:4) blocks of required size, applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I.
314	Providing 12 mm cement plaster (1:4) with clean coarse sand of F.M 1.5 including cost of screening, curing with all leads and lifts of water,scaffolding,taxes and royalty all complete as per building specification and direction of E/I.
315	Providing 12 mm cement plaster (1:6) with clean coarse sand of F.M 1.5 including cost of screening, curing with all leads and lifts of water,scaffolding,taxes and royalty all complete as per building specification and direction of E/I.
316	Providing 6 mm cement plaster (1:4 ) in ceiling with clean coarse sand of F.M 1.5 including cost of screening, curing with all leads and lifts of water,scaffolding,taxes and royalty all complete as per building specification and direction of E/I.
317	Providing 12 mm cement plaster (1:3) with clean coarse sand of F.M 1.5 with floating coat of neat cement in skirting including rounding of junctions with floor,curing,taxes and royalty all complete as per building specification and direction of E/I.
318	Providing 19 mm water proof cement plaster (1:3) with clean coarse sand of F.M 1.5 with 5% cico or any other approved water proofing compound including cost of screening, curing with all leads and lifts of water,scaffolding,taxes and royalty all complete as per building specification and direction of E/I.
319	Providing 1.5 mm cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of E/I.
320	Providing two coats of snowcem of approved shade and make over old surface including washing, cleaning, sand papering the wall,scaffolding,curing and taxes all complete as per building specification & direction of E/I.
321	Extra for each coat of cement wash, distemper paint or snowcem over exterior surface for each consecutive floor above first floor including scaffolding etc all complete as per building specification & direction of E/I.
322	Providing two coats of synthetic enamel paint of approved shade and make over steel surface throughly,scaffolding and taxes all papering including cost of scaffolding and taxes all complete as per building specification & direction of E/I.
323	Providing and fixing G.I. pipe railing having 1.0 M height consisting 50 x 50 x 6 mm thick M. S. angles as verticals at 1.5 M c/c, and additional posts at every corner with 3 rows of 25 mm dia G.I. pipes of medium class variety as horizontal and painting 3 coats of oil paint over 1 coat of anticorrosive paint of approved colour and shade including cost of all labour, transporting bends to curved shape, etc. complete.
324	Providing and fixing in position M.S. ladder 0.50 M wide consisting of 75 x 10 mm M.S. flats as stringers and 16 mm dia M.S. bars in double rows as steps placed at 25 cm c/c including cost of material and labour involved, welding, anchoring and applying 3 coat of anti-corrosive paint, etc. complete as directed by Engineer-in-charge.
325	Carriage of materials from different sources or departmental stores to work site including loading, transporting, unloading and stacking the materials at work site etc. all complete job. as per direction of E/I.
326	Cement Lead 10 Km (avg.)
327	Sand Lead 36 Km (avg.)
328	Stone Chips Lead 11 Km (avg.)
329	Steel ReinforCement Lead 10 Km (avg.)
330	Bricks Lead 06 Km (avg.)
331	Distribution Network & House Connection20 -40 Nos. including Platform & Stand post
332	Earth work in excavation in foundation trenches in hard soil (Vide Classification soil item B) and disposal of excavated earth as obtained to a distance up to 50 Mtr. including all lifts, leveling, ramming the foundation trenches, removing roots of trees, shrubs all complete as per approved design, specification and direction of E/I.
333	Dismantling plain cement concrete work including stacking serviceable materials in countable stacks within 15 M lead and disposal of unserviceable materials with all leads all complete.
334	Providing PCCM-200 with nominal mix of (1:1.5:3) with approved quality of stone chips 20 mm to 6 mm size graded and clean coarse sand of FM 2.5 to 3.0 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, sticking, curing , taxes and royalty all complete as per specification and direction of E/I.
335	Rising Main
336	Manufacture, supply and Delivery offollowing Nominal dia UPVC column pipes including PVC socket (Coupler),
337	65mm dia -Density of pipe 1.38 to 1.43 Gm per Cm3 OD:74.5 to 75.2mm wall Thickness End:9mm to 10.7mm, Barrel 9mm to 10.7 mm, Length: 3Mtrs.Rising main
338	50 mm dia -Density of pipe 1.38 to 1.43 Gm per Cm3 OD:87.5 to 88.2mm wall Thickness End:9 .8 mm to 11.9mm, Barrel 7.3mm to 9 mm, Length: 3Mtrs. Delivery Pipe
339	Distribution
340	Providing and supplying High Density Polyethylene pipe (HDPE pipe) of 20 mm to 225 mm OD and pressure 6.0 Kg/cm2 and 10 Kg/cm2 suitable for water supply which is available in all standard conforming to ISI -- 4984/14151/12786/13488,ISO 4427 , DIN-8074materials rates are Ex-factory excluding transportation, taxes and duties. PE-80 , PN- 10
341	63 mm HDPE Pipe
342	50 mm HDPE Pipe
343	32 mm HDPE Pipe
344	20 mm HDPE Pipe
345	Providing and fixing Gun Metal Gate valvewith C I wheel of approved quality(screwed end).
346	65 mm dia.
347	50 mm dia.
348	Providing and supplying High Density Polyethylene(HDPE )fittings of 20 mm to 225 mm OD and pressure 6.0 Kg/cm2 and 10 Kg/cm2 suitable for water supply which is available in all standard conforming to ISI -- 4984/14151/12786/13488,ISO 4427 , DIN-8074materials rates are Ex-factory excluding transportation, taxes and duties. PE-80 , PN- 10
349	Lowering, Laying and Jointing H. D. P. E./M. D.P. E. pipes in proper position including all specials by compression fitting/electro fusion and butt fusion jointing procedure as per relevant IS Code complete with all materials for jointing procedure like Electro fusion machine, Electric heater/butt fusion welding machine with hydraulic jack, top loading clamp etc. and all labours as directed by engineer in charge as per IS-7634 Part II.
350	For Rising
351	65 mm HDPE Pipe
352	50 mm HDPE Pipe
353	Distribution
354	65 mm HDPE Pipe
355	50 mm HDPE Pipe
356	32 mm HDPE Pipe
357	20 mm HDPE Pipe
358	Providing 15 mm dia. G.I. pipe Tata or equivalent make as per IS 1239 (Part 1/2004) ISI Mark /medium quality in Stand Post.
359	Supplying all materials , labour and tools for fixing 15 mm dia G.I. pipes with Red lead and yarn of following nominal bore with screwed and socketed joints on wall, ceiling and floor including supplying and fitting of wall hooks or pipe clamps, wooden plugs, cutting pipes to size and threading ends if required etc. all complete as per specification and direction of Engineer-in-Charge.
360	Supplying and fixing G.I. fittings of approved make all complete as per specification and direction of E/I.
361	Elbow 15 mm dia.
362	Reducer Socket 20x15 mm dia.
363	Nipple 15 mm dia.
364	Plain Socket 15 mm dia.
365	Supplying and fixing G.M. ferrule of approved make in existing C.I./D.I. main Including drilling and taping C.I./D.I. main all complete as per specification and direction of E/I. 3 mm, 6 mm 10 mm dm ferrule weight not less than 425 gram.
366	Providing and fixing of male ended C.I.Body brass spindle valve and seat Bib cock of approved quality with extra socketall complete as per specification and direction of E/I.
367	15 dia and weight not less than 400 Gm
368	Providing and fixing Gun Metal full way valve of approved quality, all complete, as per specification and direction of E/I.
369	65 mm dia Full way valve
370	50 mm dia and weight not less than 1.5 Kg
371	Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design.With common burnt clay F.P.S.(non modular) bricks of class designation 7.5. Full way valve chamber
372	Providing brick masonry chamber ofinner size 600 x 600 x 450 mm deep for bore well protection having 125 mm thick wall and 75 mm R.C.C cover including cement plaster of exposed surface, etc all complete job
373	Supplying materials , labours and equipments for construction of 0.90M x 0.90 M size P.C.C. (1:2:4) Rectangular Platform with stand post in house including 12 mm thick cement plaster in C.M. (1:4) with neat cement punning over exposed surfaceall complete job, as per approved design, specification and direction of E/I.
374	Earth work in back filling the trenches after laying different types and size of pipes with earth removed during excavation within initial lead and lift as per specification and direction of Engineer-in-Charge.
375	Providing fitting & fixing 32 mm to 50 mm service HDPE saddleall complete job, as per approved design, specification and direction of E/I.
376	Carriage of materials from different sources or departmental stores to work site including loading, transporting, unloading and stacking the materials at work site etc. all complete job. as per direction of E/I.
377	Cement Lead 10 Km (avg.)
378	Sand Lead 36 Km (avg.)
379	Stone Chips Lead 11 Km (avg.)
380	Steel ReinforCement Lead 10 Km (avg.)
381	Bricks Lead 06 Km (avg.)
382	Annual Operation & Maintenance cost based on Existing D/T Well with solarmotor pump for 5 years
383	O & M Cost for 1st year (Excluding Repair Charges)
384	O & M Cost for 2nd year with Annual Repair Charges
385	O & M cost for 3rd Year
386	O & M cost for 4th Year
387	O & M cost for 5th Year
388	Provision of one no SIM card & its recharging cost for RMC (01 SIM Each Year)
389	Add 18% GST
390	Add 1% Labour Cess

Also Visit

Tenders

Jharkhand Tenders

Construction Tenders

Water Storage and Supply Tenders

Water Supply Project Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Cluster Wise Single Village Water Supply Schemes Under Jal Jeevan Mission Block Nagar Untari Panchayat-Garbandh Hulhula Khurd Haliwanta Kala And Narhi Cluster No-26 Under Drinking Water And Sanitation Division Garhwa For The Year 2022, Garhwa-Jharkhand

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Cluster Wise Single Village Water Supply Schemes Under Jal Jeevan Mission Block Nagar Untari Panchayat-Garbandh Hulhula Khurd Haliwanta Kala And Narhi Cluster No-26 Under Drinking Water And Sanitation Division Garhwa For The Year 2022, Garhwa-Jharkhand

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us