Public Works Department-PWD has published Tender For Construction Of 08 Numbers Of New Residential Quarters For Judicial Officers Of Various Grade [ Grade-I: 03 Nos, Grade-Ii: 03 Nos, Grade-Iii: 02Nos.] At Bishramganj Under Sepahijala District/Sh: Building Portion Including Internal Water Supply,. Submission Date for this Tender is 06-02-2023. Electrification Work Tenders in Sepahijala Tripura. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | SUB-HEAD : EARTH WORK |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. - All kinds of soil |
| 3 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. - All kinds of soil |
| 4 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. - All kinds of soil |
| 5 | Extra for additional lift of 1.5m or part thereof. - All kinds of soil |
| 6 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete. |
| 7 | Supplying chemical emulsion in sealed containers including delivery as specified. |
| 8 | (i) Chlorpyriphos/Lindane emulsifiable concentrate of 20% |
| 9 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment as per IS: 6313 (Part III)- Latest revision (excluding the cost of chemical emulsion): |
| 10 | (i) Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. - With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. |
| 11 | (ii) Treatment of soil under plinth filling using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with sand filling: - With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. |
| 12 | SUB-HEAD : CEMENT CONCRETE WORK |
| 13 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - - All work upto plinth level: |
| 14 | (i) 1:4:8 ( 1 Cement: 4 fine sand : 8 graded stone aggregate 40 mm nominal size) |
| 15 | (ii) 1:3:6 ( 1 Cement: 3 fine sand : 6 graded stone aggregate 20 mm nominal size) |
| 16 | (iii) 1:2:4 ( 1 Cement: 2 fine sand : 4 graded stone aggregate 20 mm nominal size) |
| 17 | Centering shuttering including struttings, propping etc. and removal of form work for: |
| 18 | (i) Foundations, footings, bases for columns. |
| 19 | Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer"s specification |
| 20 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 fine sand : 6 graded well burnt brick aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. |
| 21 | SUB-HEAD : RCC WORK |
| 22 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement- -All work upto plinth level: |
| 23 | (i) 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 24 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and skirting courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement- |
| 25 | (i) 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 26 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement- |
| 27 | (i) 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 28 | Reinforced cement concrete work in arches, archribs, domes, vaults, shells, folded plate and roofs having slope more than 15° up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with |
| 29 | (i) 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 30 | Reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers, facias and eaves boards above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with |
| 31 | (i) 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 32 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete uptoplinth level. |
| 33 | (i) Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 34 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. |
| 35 | (i) Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 36 | Providing precast cement concrete Jali 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 6mm nominal size) reinforced with 1.6 mm dia mild steel wire including centring and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3(1cement : 3 fine sand)etc. complete, excluding the plastering of jambs, sills and soffits |
| 37 | (i) 50 mm thick |
| 38 | Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete in vertical & horizontal fins, individually or forming box louvers, setting in cement mortar 1:2 (1 cement : 2 coarse sand), including the cost of required centering, shuttering but , excluding the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size). |
| 39 | Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size). |
| 40 | Providing and fixing in position copper plate as per design for expansion joints. |
| 41 | Centering shuttering including struttings, propping etc. and removal of form work for: |
| 42 | (i) Foundations, footings, bases for columns etc. for mass concrete with timber plank |
| 43 | (ii) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. using shuttering ply |
| 44 | (iii) Suspended floors, roofs, landings, balconies and access platform with 12 mm thick shuttering ply |
| 45 | (iv) Lintels, beams, plinth beams, girders, bressumers and cantilevers with shuttering ply |
| 46 | (v) Columns, Pillars, Piers, Abutments, Posts and Struts with shuttering ply |
| 47 | (vi) Stairs (excluding landings) except spiral-staircases with wooden plank |
| 48 | (vii) Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards. |
| 49 | (viii) Edges of slabs and breaks in floors and walls under 20 cm. wide |
| 50 | (ix) Weather shade, Chajjas, corbels etc., including edges. |
| 51 | SUB-HEAD : BRICK WORK |
| 52 | First class brick work in foundation and plinth including cost of all materials as required complete:- |
| 53 | (i) In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 54 | (ii) In cement mortar 1:6 ( 1 cement : 6 fine sand ). |
| 55 | First class brick work in superstructure above plinth level & upto floor-five level including cost of all materials as required complete:- |
| 56 | (i) In cement mortar 1:6 ( 1 cement : 6 fine sand ). |
| 57 | (i) In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 58 | Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:- |
| 59 | (i) In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 60 | Extra for providing & placing in position 2 nos 6mm dia MS bars at every 6th course offull brick masonry work including anchorage in joints of 75mm in each side in superstructure for all level including cost of all materials as required complete:- |
| 61 | (i) In cement mortar 1:6 ( 1 cement : 6 fine sand ). |
| 62 | Extra for providing & placing in position 2 nos 6mm dia MS bars at every 4th course ofhalf brick masonry work including anchorage in joints of 75mm in each side in superstructure for all levelincluding cost of all materials as required complete:- |
| 63 | (i) In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 64 | SUB-HEAD : CLADDING WORK |
| 65 | Providing and fixing gangsawcutofapproved thickness mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base of cement mortar 1:4 ( 1 cement : 4 fine sand ) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing , curing, moulding and polishing to edges to give high gloss finish etc.complete at all levels:- |
| 66 | (i) 18 mm thick Rajnagar Plain white marble/ Udaipur green marble/ Zebra black marble or equivalent duly approved:- - Area of slab upto 0.50 sqm. |
| 67 | (ii) 18 mm thick Granite of any colour and shade duly approved:- - Area of slab upto 0.50 sqm. |
| 68 | Providing edge moulding to approved thickness marble stone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete at all levels as required as per design approved by the Engineer-in-charge:- |
| 69 | (i) 18 mm Marble work. |
| 70 | (ii) 18 mm thick Granite work. |
| 71 | SUB-HEAD : WOOD & PVC WORK |
| 72 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position : |
| 73 | (i) Local Teak wood |
| 74 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for paneled or paneled and glazed shutters 25 to 40 mm thick. |
| 75 | (i) Local Teak Wood 16mm. Thick |
| 76 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veeners on both faces of shutters. |
| 77 | (i) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 78 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete. |
| 79 | (i) Fixed to openings /wooden frames with rawl plugs screws etc. |
| 80 | Providing 40 × 5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30 × 10 × 15 cm 1:3:6 mix (1 cement : 3 fine sand : 6 graded stone aggregate 20mm nominal size) |
| 81 | Providing and fixing bright finished brass butt hinges with necessary screws etc.complete : |
| 82 | (i) 125 x 85 x 5.5 mm (heavy type) |
| 83 | (ii) 100 x 85 x 5.5 mm (heavy type) |
| 84 | Providing and fixing bright finished brass door latch with necessary screws etc. complete : |
| 85 | (i) 300 x 16 x 5 mm |
| 86 | (ii) 250 x 16 x 5 mm |
| 87 | Providing and fixing bright finished brass towerbolts (barrel type) with necessary screws etc. complete : |
| 88 | (i) 250 x 10 mm |
| 89 | (ii) 200 x 10 mm |
| 90 | Providing and fixing bright finished brass handles with screws etc. complete : |
| 91 | (i) 125 mm |
| 92 | (ii) 100 mm |
| 93 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. |
| 94 | Providing and fixing bright finished brass 100 mm mortice latch and lock ISI marked with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles with necessary screws etc. complete (Best make of approved quality) |
| 95 | Providing and fixing IS : 3564 marked Aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc. complete. |
| 96 | Providing and fixing factory made door frame (single rebate) made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 60mm width & 30mm thickness and shall be fixed to wall as per instructions of Engineer-In-Charge using 100x8 sheet metal CSK screws. |
| 97 | Providing and fixing 28 mm thick door shutter made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 71mm width & 28mm thick as vertical & horizontal styles. Joints are made using solventadhesive and GI ‘C sections (39mm x 19mm x 0.6mm thick) or M S pipe (40mm x 20mm ) stiffener frame insert & telescopic polymeric ‘L’ corners .The panel shall be filled with 3mm thick high - pressure compact laminate as per manufacturer’s specifications and directions of the Engineer-in-charge, cover moulding shall be provided for covering fixing screws and elegant look.( for W.C. bathroom door shutter). |
| 98 | Providing and fixing IS : 3564 marked aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessaryaccessories and screws etc. complete. |
| 99 | Providing 50 × 50 × 50 mm Gamair wood plugs including cutting brick work and fixing in cement mortar 1:3 (1 cement: 3 fine sand) and making good the walls etc. |
| 100 | SUB-HEAD : STEEL WORK |
| 101 | Providing and fixingfan clamp type-Iof 16 mm dia M.S. bar bent to shape with hooked ends in R.C.C. slabs during laying including painting the exposed portion of loop, all as per standard design complete. |
| 102 | Providing structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as required. |
| 103 | Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm at 100 mm centre to centre and braced with flat iron diagonals 20x5mm size with top and bottom rail of T-iron 40x40x6mm with 40mm dia. steel pulleys & with riveted bolts, nuts, locking arrangement, stoppers, handles, hold fast /anchor bolt including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approved steel primer etc. complete as required. |
| 104 | Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. complete as required:- |
| 105 | (i) In stringers, treads, landing etc. of stair cases including use of chequered plate wherever required, all complete. |
| 106 | (ii) In grating, frames, guard bar, railing, brackets, gates and similar works, all complete. |
| 107 | Providing and fixing hand rail using structural steel etc. of approved size by welding etc. to steel ladder railing, balcony railing and staircase railing etc. including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer complete as required:- |
| 108 | (i) M.S. tube |
| 109 | Providing and fixing M.S. round holding down bolts with nuts and wahser plates complete as per standard design. |
| 110 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 111 | SUB-HEAD : ALUMINIUM WORK & STRUCTURAL GLAZING |
| 112 | Providingandfixingaluminiumworkfordoors,windows,ventilators and partitions withextrudedbuiltupstandardtubularsections/ appropriateZsectionsandothersectionsofapprovedmake conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawingandthedirectionofEngineerincharge.(Glazingand paneling and dash fasteners to be paid for separately) :- |
| 113 | (i) For fixed portion of approved quality:- - Anodisedaluminium(anodisedtransparentordyedto requiredshadeaccordingtoIS:1868,Minimumanodic coating of grade AC 15). |
| 114 | (ii) For shutters of doors, windows & ventilatorsincluding providing and fixing hinges / pivots and making provision for fixing fittings wherever required including the cost of EPDM rubber / neoprene gasket required ( Fittings shall be paid for separately ):- - Anodisedaluminium(anodisedtransparentordyedto requiredshadeaccordingtoIS:1868,Minimumanodic coating of grade AC 15). |
| 115 | Providing and fixing glazing of approved quality in aluminium doors,windows, ventilator, shutters and partition etc. with EPDM rubber / neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge (Cost of snap beading shall be paid in basic item) :- |
| 116 | (i) With float glass panes of 4.0 mm thickness ( weight not less than 10.0 kg / sqm ) |
| 117 | (ii) With float glass panes of 5.5 mm thickness ( weight not less than 13.50 kg / sqm ) |
| 118 | Providing and fixing stainless steel ( SS 304 grade ) adjustable friction window stay of approved quality with necessary stainless steel screws etc. to the side hung windows etc. complete as per direction of Engineer-in-charge:- |
| 119 | (i) 205 x 19 mm |
| 120 | Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. of approved quality completeas per direction of Engineer-in-charge:- |
| 121 | (i) Anodised aluminium of grade AC 15. |
| 122 | Providing and fixing 100 mm brass locks (best make of approved quality) with 6 levers without pair of handles for aluminium doors including necessary cutting and making good etc. completeas per direction of Engineer-in-charge. |
| 123 | SUB-HEAD : FLOORING AND SKIRTING WORK |
| 124 | Providing and fixingMarble stone in floors over 20 mm thick bed ofcement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with ordinary cement slurry including pointing with white cement mixed with of matching shade, including rubbing and polishingcomplete. |
| 125 | (i) 18mm thick Marble Stone - Rajnagar plain marble |
| 126 | Tile work in skirting, risers of steps and dado up to 2 m height over 12 mm thick bed of cement mortar 1:3 (1 cement :3 fine sand) and jointed with grey cement slurry @ 3.3 kg/sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 127 | (i) 8mm thick Rajnagar marble tiles (polished) |
| 128 | Extra for prefinished nosing to treads of steps of marble stone. |
| 129 | Providing and laying ceramic floor tiles in different sizes (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 - 2017 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid over 20 mm thick cement mortar 1:4 (1 cement : 4 fine sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. complete. |
| 130 | (i) Mat Finish Tiles - Ceramic Tiles 1st quality 400 x 400mm in all shades and designs |
| 131 | (ii) Anti-Skid Tiles - Ceramic Tiles 1st quality 400 x 400mm in all shades and designs |
| 132 | Providing and fixing Kota stone in floors over 20 mm thick bed ofcement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with ordinary cement slurry including pointing with ordinary cement mixed with pigment of matching shade, including rubbing and polishingcomplete. |
| 133 | (i) Kota stone slab 25mm thick |
| 134 | Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1 : 3 ( 1 cement : 3 fine sand ) and joined with ordinary cement slurry mixed with pigment to match the shade of slabs, including rubbing and polishing complete. |
| 135 | Providing and fixing 1st quality ceramic glazed wall tiles (minimum 200 x 300) conforming to IS : 15622 - 2017 (thickness to be specified by the manufacturer) of approved make in all colours, shadesof any size as approved by Engineer-in-charge in skirting, risers of steps and dados, laid over 12 mm thick bed of cement mortar 1 : 3 (1 cement : 3 fine sand) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade complete. |
| 136 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 - 2017, of approved make, in all colours and shades, laid over 20mm thick cement mortar 1:4 (1 cement : 4 fine sand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding grouting the joints with white cement and matching pigments etc., complete. |
| 137 | (i) Double charged Stainfree vitrified tiles - Size of tile 60x60 cm |
| 138 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622 - 2017, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 fine sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete |
| 139 | (i) Double charged Stainfree vitrified tiles - Size of tile 60x60 cm |
| 140 | Providing and fixing precast chequered cement concrete tiles 18 mm thick, laid in footpath & courtyard, on 20 mm thick bed ofcement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with neat cement slurry including rubbing and cleaning complete as per direction of the Engineer-in-Charge. |
| 141 | Providing and fixing 25 mm thick pre-polished colored concrete designer tiles making by strong vibratory compaction technology using 50% white cement and 50% ordinary cement of size 300mm x 300mm, laid in footpath & courtyard, on 20 mm thick bed ofcement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc. complete as per direction of the Engineer-in-charge. |
| 142 | Providing and laying cement concrete 1:2:4 (1 cement: 2 fine sand : 4 graded well burnt brick aggregate) flooring finished with a floating coat of neat cement including cement slurry, rounding of edges and strips and cost of glass strips etc. complete. |
| 143 | (i) 40 mm thick |
| 144 | SUB-HEAD : ROOFING AND CEILING WORK |
| 145 | Supply & installation of pre-painted Galvalume sheetsfor roofing/cladding (size, shapeandpitch of corrugation as approvedby Engineer-in-charge)in 550mpasteelgrade, made out of Cold Rolled Steel coated with Zinc-Aluminium alloy coating of 43.5% Zn, 55% Al and 1.5% Silicon confirming to ASTM A792/A792M and AS1397, Alloy coating AZ150/AZ70, colour coated with high quality Polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side. Sheet shouldhaveprotectiveguardfilmof25micronsminimumtoavoid scratcheswhiletransportationandshouldbesupplied in singlelength upto 12 metre or as desired byEngineer-in-charge.The sheet shall be fixedusingselfdrilling/selftappingscrewsofsize(5.5x55mm)with EPDM washersfilledwithwhiteleadcompleteuptoanypitchinhorizontal/ verticalorcurvedsurfacesexcludingthecostofpurlins, raftersand trusses and including cutting to size and shape wherever required. |
| 146 | i) 0.60mm thickness |
| 147 | Supply & installation of pre-painted Galvalume sheets roofing accessories in 550mpasteelsteelgrade, made out of Cold rolled steel coated with Zinc-Aluminium alloy coating of 43.5% Zn, 55% Al and 1.5% Silicon confirming to AASTM A792/A792M and AS1397, Alloy coating AZ150/AZ70, colour coated with high quality polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side. Sheet shouldhaveprotectiveguardfilmof25micronsminimumtoavoid scratcheswhiletransportation. Sheet shouldhaveprotectiveguardfilmof25micronsminimumtoavoid scratcheswhiletransportation. The sheet shall be fixedusingselfdrilling/selftappingscrewswith EPDMwashers complete for Ridges/Valley/Gutter/Flashing of width 610mm: |
| 148 | i) 0.60mm thickness |
| 149 | ProvidingandfixingonwallfaceunplasticisedRigidPVCrainwater pipes (working pressure 4 kg/cm2)conformingto IS : 13592 Type Aincludingjointingwith sealring conformingtoIS:5382leaving10mmgapforthermalexpansion: |
| 150 | (i) Single socketed pipe - 110 mm OD |
| 151 | Providingandfixing on wallface unplasticised - PVCmouldedfittings/ accessoriesfor unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type-Aincludingjointingwith sealringconformingtoIS : 5382 leaving 10 mm gap forthermalexpansion: |
| 152 | (i) Coupler - 110mm |
| 153 | (ii) Single equal tee with door - 110 x 110 x 110 mm |
| 154 | (iii) Single equal tee without door - 110 x 110 x 110 mm |
| 155 | (iv) Bend 87.5 - 110mm |
| 156 | (v) Plain shoe - 110 mm |
| 157 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised-PVCrainwater pipesbymeansof50x50x50mmhard woodplugs,screwedwithM.S.screwsofrequiredlengthincluding cutting brick work andfixing with cement mortar 1 : 4 (1cement : 4 fine sand) making good the wall etc. complete. |
| 158 | (i) 110mm |
| 159 | Providing and fixing to the inlet mouth of rain water pipe PTMT grating with thickness of 8mm and weighing not less than 100gm. complete. |
| 160 | (i) 100mm |
| 161 | SUB-HEAD : FINISHING WORK |
| 162 | 12 mm cement plaster of mix |
| 163 | (i) In cement mortar 1 : 4 ( 1 cement : 4 fine sand ) |
| 164 | (ii) In cement mortar 1 : 6 ( 1 cement : 6 fine sand ) |
| 165 | 15 mm cement plaster on the rough side of single or half brick wall of mix: |
| 166 | (i) Cement mortar 1:4 (1 cement : 4 fine sand) |
| 167 | (ii) Cement mortar 1:6 (1 cement : 6 fine sand) |
| 168 | 6 mm cement plaster of mix: |
| 169 | (i) In cement mortar 1 : 3 ( 1 cement : 3 fine sand ) |
| 170 | Neat cement punning. |
| 171 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : |
| 172 | (i) New work ( two or more coats) over and including water thinnable priming coat with cement primer. |
| 173 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 174 | Finishing walls with premium acrylic smooth exterior paint with Silicon additives of required shade of approved brand and manufacture [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : |
| 175 | (i) New work ( two or more coats applied @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 176 | Applying priming coat [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : |
| 177 | (i) With ready mixed Pink or Grey primer of approved brand and manufacture on wood work ( hard & soft wood ). |
| 178 | (ii) With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works |
| 179 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]: |
| 180 | (i) Two or more coats on new work |
| 181 | SUB-HEAD:WATER PROOFING WORK |
| 182 | Grading roof for water proofing treatment complete as required as per direction of the Engineer-in-charge with : |
| 183 | (i) Cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded stone aggregate 20 mm nominal size) |
| 184 | (ii) Cement mortar 1:4 (1cement : 4 fine sand) |
| 185 | Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like as required as per direction of the Engineer-in-charge, consisting of : (i) 1st course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) 2nd course of 20 mm cement plaster 1:3 (1 cement : 3 fine sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) 3rd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) 4th course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/ sqm). |
| 186 | SUB-HEAD : SANITARY WORKS |
| 187 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushingcisternwithmanuallycontrolleddevice(handlelever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : |
| 188 | (i) White Vitreous china Orrisa pattern W.C. pan of size 580x440 mm with integral type foot rests. |
| 189 | Providingandfixingwhitevitreouschinapedestaltypewatercloset (Europeantype W.C.pan)withseatandlid,10litrelowlevelwhite P.V.C.flushing cistern withmanually controlled device (handlelever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : |
| 190 | (i) W.C. pan with ISI marked white solid plastic seat and lid |
| 191 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm sizes respectively. |
| 192 | Providing and fixing white vitreous china squatting plate urinal with integral rim longitudinal flush pipe. |
| 193 | Providingand fixing wash basinwith C.I. brackets, 15 mm C.P. brass pillartaps,32mmC.P.brasswasteofstandardpattern,including paintingoffittingsandbrackets,cuttingandmakinggoodthewalls wherever require : |
| 194 | (i) White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar taps. |
| 195 | Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required: |
| 196 | (i) Kitchen sink without drain board - 610x460 mm bowl depth 200 mm. |
| 197 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 198 | (i) Semi rigid pipe - 32 mm dia |
| 199 | (ii) Flexible pipe - 32 mm dia |
| 200 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : (i) Circular shape 450 mm dia |
| 201 | Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 202 | Providing and fixing toilet paper holder : (i) C.P. brass |
| 203 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour. |
| 204 | (i) 600mm long towel rail with total length of 645mm, width 78mm and effective height of 88mm, weighing not less than 190gms. |
| 205 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements weighing not less than 106 gms. |
| 206 | Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colours weighing not less than 105 gms. |
| 207 | Providing and fixing PTMT towel ring trapezoidal shape 215mm long, 200mm wide with a minimum distances of 37mm from wall face with concealed fittings arrangement of approved quality and colours weighing not less than 80 gms. |
| 208 | ProvidingandfixingonwallfaceunplasticisedRigidPVC rain water, soil, waste & vent pipes (working pressure 6 kg / cm2)conformingto IS : 13592 Type Aincludingjointingwith sealring conformingtoIS:5382leaving10mmgapforthermalexpansion: |
| 209 | (i) Single socketed pipe-100 mm OD |
| 210 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised-PVCrainwater, soil, waste & vent pipesbymeansof50x50x50mmhard woodplugs,screwedwithM.S.screwsofrequiredlengthincluding cutting brick work andfixing with cement mortar 1 : 4 (1cement : 4 fine sand) making good the wall etc. |
| 211 | i) 110mm |
| 212 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water, soil, waste & vent pipes pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap forthermalexpansion: |
| 213 | (i) Coupler - 110mm |
| 214 | (ii) Single equal tee without door - 110 x 110 x 110 mm |
| 215 | (iii) Single equal tee with door - 110 x 110 x 110 mm |
| 216 | (iv) Bend 87.5 - 110mm |
| 217 | (v) Plain shoe - 110 mm |
| 218 | (vi) Doubleequal junction of required degreewithout door - 110x110x110 x110 mm |
| 219 | (vii) Doubleequal junction of required degreewith door - 110x110x110 x110 mm |
| 220 | (viii) Terminal guard - 110 mm |
| 221 | SUB-HEAD : WATER SUPPLY |
| 222 | Providing and fixing G.I. pipes of medim class as per IS : 1239 with latest amendment complete with G.I. fittings and clamps, including cutting and making good the walls etc. complete as per CPWD specification and direction of the Engineer - in - charge. - Internal work - Exposed on wall. |
| 223 | (i) 15 mm dia. nominal bore |
| 224 | (ii) 20 mm dia. nominal bore |
| 225 | (iii) 25 mm dia. nominal bore |
| 226 | (iv) 40 mm dia. nominal bore |
| 227 | Providing and fixing G.I pipesof medim class as per IS : 1239 with latest amendment complete with G.I. fittings and clamps, including making good the walls/floor etc. concealed pipe includingpainting two coats or more with anticorrosive bitumastic paint, cutting chases and making good the same complete as per CPWD specification and direction of the Engineer - in - charge. |
| 228 | (i) 15 mm dia. nominal bore |
| 229 | (ii) 20 mm dia. nominal bore |
| 230 | Making connection of G.I. distribution branch with G.I. mainfollowing sizes by providing and fixing tee, including cutting and threading the pipe etc. complete as per CPWD specification and direction of the Engineer - in - charge. |
| 231 | (i) 25 to 40 mm nominal bore |
| 232 | Providing and fixing brass bib cock of approved quality : |
| 233 | (i) 15 mm nominal bore |
| 234 | Providing and fixing brass stop cock of approved quality : |
| 235 | (i) 15 mm dia nominal bore |
| 236 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): |
| 237 | (i) 25 mm nominal bore |
| 238 | (ii) 40 mm nominal bore |
| 239 | Providing and fixing gun metal non-return valve of approved quality (screwed end): |
| 240 | (i) 25 mm nominal bore - Vertical |
| 241 | (ii) 40 mm nominal bore - Vertical |
| 242 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 243 | Constructing masonryChamber 30x30x50 cm, inside , in brick workincement mortar1:4 (1 cement :4 fine sand) forstopcock, withC.I.surface box100x100x75mm (inside)with hingedcover fixedincement concreteslab1:2:4mix (1 cement:2 coarsesand:4gradedstoneaggregate20mmnominalsize) necessary excavation foundationconcrete 1:5:10 ( 1cement :5fine sand:10gradedstoneaggregate40mmnominalsize)andinside plastering with cement mortar 1:3 (1 cement :3 coarsesand) 12mm thick finishedwithafloatingcoatofneatcementcompleteasper standard design : |
| 244 | (i) With Second Class bricks |
| 245 | Painting G.I. pipes and fittings with synthetic enamel white paint with two coats overa ready mixed priming coat, both of approved quality for new work : |
| 246 | (i) 15 mm diameter pipe. |
| 247 | (ii) 20 mm diameter pipe. |
| 248 | (iii) 25 mm diameter pipe. |
| 249 | (iv) 40 mm diameter pipe. |
| 250 | Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality : |
| 251 | (i) 15 mm diameter pipe |
| 252 | (ii) 20 mm diameter pipe |
| 253 | (iii) 25 mm diameter pipe |
| 254 | (iv) 40 mm diameter pipe |
| 255 | Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws including excavation, refilling the earth or cutting of wall and making good the same complete wherever required : |
| 256 | (i) 25 mm nominal bore. |
| 257 | (ii) 40 mm nominal bore. |
| 258 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet: |
| 259 | (i) 100 mm diameter |
| 260 | SUB HEAD : SEWAGE AND DRAINAGE WORKS |
| 261 | Providing, laying and jointing glazed stoneware pipes grade ‘A’ with stiff mixture of cement mortar in the of 1:1 (1 cement: 1 fine sand) including testing of joints etc. complete : |
| 262 | (i) 150 mm diameter |
| 263 | Providing and laying cement concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) alround S.W. pipes including bed concrete as per standard design: |
| 264 | (i) 150 mm diameter S.W, pipe |
| 265 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with well burnt 2nd class bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. |
| 266 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with 1st class bricks in cement mortar 1:4 (1 cement : 4 fine sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C. top slab with 1:2:4 mix (1 cement :2 fine sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement: 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 fine sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design : |
| 267 | (i) Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets : |
| 268 | Extra for depth beyond 450 mm of brick masonry chamber for underground C.I. inspection chamber with same specification as mentioned in item no 20.330 complete as per standard design : |
| 269 | (i) For 500x700 mm size |
| 270 | SUB HEAD : MISCELLANEOUS WORK |
| 271 | 60 mm thick factory made c.c. interlocking paver block of M-35GradeProviding and laying factory made coloured chamfered edge Cement Concrete paver blocks of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. complete as per specifications & approval/ direction of Engineer-in-Charge.- (a) 60 mm thick c.c. paver block of M-35 grade with approved colour, design and pattern. |
| 272 | Supplying and installation of 2 H.PMono block Pump 50x40 mm Suction and delivery pipe complete fabricated to C.0 base of standard size with holding down bolt with panel board, single phase connection motor and starter to main switch, indicator and earthening etc. complete as per direction of the Engineer-In-Charge (No additional cost for electrification upto main switch will be paid seperately) Measurement to be taken after successful operation of the Pump) |
| 273 | SUB HEAD : INTERNAL ELECTRIFICATION WORK |
| 274 | Wiring for light/ fan/ exhaust fan/ call bell point with 2x1.5 sq. mm PVC insulated copper conductor cable (FR) in PVC conduit (medium gauge) recessed in slab/ wall complete with 6/10 amps modular type switch, cover plate, GI box including necessary connection etc. as required. |
| 275 | Wiring for 2 way controlling light point with 3x1.5 sq. mm PVC insulated copper conductor cable (FR) in PVC conduit (medium gauge) recessed in slab/ wall complete with 6/10 amps modular type 2 way switch, cover plate, GI box including necessary connection etc. as required. |
| 276 | Providing and fixing of 3 pin 6/10 amps plug point withmodulartype 6/10ampsswitch andsocketincludingconnectionwith 2 x 1.5 sq. mm PVC insulated Copper conductor cable (FR) onmodular concealedswitch board with cover plate earthing the 3rd pin etc. as required. |
| 277 | Providing and fixing of 3/6 pin 16/20 amps plug point withmodulartype 16/20ampsswitch andsocketincludingconnectionwith 2 x 2.5 sq. mm PVC insulated Copper conductor cable (FR) onmodular concealedswitch board with cover plate earthing the 3rd pin etc. as required. |
| 278 | Wiring for Circuit/Sub-main with the following sizes PVC insulated Copper conductor cable (FR) in PVC conduit (medium gauge) recessed in slab/ wall etc. as required:- |
| 279 | (i) 2 X 1.5 + 1 X 1.5 sq mm |
| 280 | (ii) 2 X 2.5 + 1 X 1.5 sq mm |
| 281 | (iii) 2 X 4 + 1 X 1.5 sq mm |
| 282 | (iv) 4 X 4+ 2 X 1.5 sq mm |
| 283 | (v) 4 X 6+ 2 X 2.5 sq mm |
| 284 | Supplying and fixing of the following modular accessories including necessary connection etc. as required. |
| 285 | (i) RJ45 LAN socket outlet (1M):- |
| 286 | (ii) TV socket outlet (1M):- |
| 287 | (iii) Blank plate (1M):- |
| 288 | (iv) Louvers/opaque type LED foot lamp (4M):- |
| 289 | (v) RJ11 telephone socket outlet (1M):- |
| 290 | (vi) 20/25 amps single phase motor starter switch (2M):- |
| 291 | Supplying & fixing of 1200 mm sweep white color AC ceilingfan capacitor typedouble ball bearing complete with 300 mm down rod,canopies,shackles, 3nos blades, including wiring the down rod with 2x1.5 sqmm PVC insulated Copper conductor cable(FR)(ISI marked, BEE 1star/minimum service value 4.0 m3/min/W) : - |
| 292 | Supplying and fixing of the following electrical accessories including necessary connection etc. as required. |
| 293 | (i) Electronic 5 step fan regulator |
| 294 | Supplying & installation of 300 mm sweep metalic body exhaust fan including connection etc as required:- |
| 295 | Supplying & installation of 225/230 mm sweep metalic body exhaust fan including connection etc as required:- |
| 296 | Supplying & installation of shutter for 225/230/300 mm sweep metalic body exhaust fan in the existing hole as required:- |
| 297 | Making different sizes of hole in the wall for fixing of exhaust fan including finishing the same with cement plastering and painting etc as required: |
| 298 | Supplying and fixing of following surface/recess mounted LED luminaries in powder coated die cast housing complete with high efficiency polycarbonate diffuser and necessary connection etc.as required (with 50000 burning hours and minimum lumen output of 100 lm/watt):- |
| 299 | (i) Surface mounted box type batten suitable for single 18/20 watt integrated LED tube lamp (without lamp):- |
| 300 | (ii) Surface mounted round/Square shaped 12 watt LED downlight with integral driver and high quality polycarbonate diffuser:- |
| 301 | Supplying and fixing of following LED Tubes, retrofit bulbs/lamps for LED luminaries including necessary connection etc. as required:- |
| 302 | (i) 18/20 watt LED tube with integral driver and polycarbonate diffuser (50000 burning hours and minimum lumen output of 100lm/watt):- |
| 303 | (ii) 9 watt LED retrofit lamp with polycarbonate body and aluminium heatsink :- |
| 304 | (iii) 20 watt LED retrofit lamp with polycarbonate body and aluminium heatsink :- |
| 305 | Supplying and fixing of following outdoor LED luminaries in powder coated die cast housing complete with heat resistant tempered glass/diffuser including necessary connection etc. as required (50000 burning hours and minimum lumen output of 100 lm/watt):- |
| 306 | (i) 36 watt LED street light fixture with integral driver and secondary lens (IP 66):- |
| 307 | (ii) 40 watt LED post top light fixture with integral driver and high quality polycarbonate diffuser (IP 65):- |
| 308 | Supplying & fixing of G.I. pipe (medium gauge) bracket fabricated at suitable angle for fixing of outdoor light on wall/ RCC base with necessary MS clamp, nut, bolt etc as required:- |
| 309 | (i) 40 mm dia |
| 310 | Supplying and fixing of the following electrical accessories including necessary connection etc. as required. |
| 311 | (i) Musical call bell |
| 312 | (ii) 3mm thick bakelite sheet |
| 313 | Supplying and installation of powder coated steel sheet enclosure (MCB DB) suitable for 240/415 volts MCB/Isolator/RCCB (SP/SPN/DP/TP/TPN/FP) complete with necessary bus bar, neutral link, din rail, earth bar etc i/c connectionas required. |
| 314 | (i) 8way horizontal TPN MCB DB (Double door):- |
| 315 | (ii) 4 way SPN MCB DB (double door):- |
| 316 | (iii) 2 way SPN MCB DB (single door):- |
| 317 | (iv) (2+10) / 12way SPN MCB DB (double door):- |
| 318 | (v) 6 way vertical TPN MCB DB suitable for FP MCB incomer (Double door):- |
| 319 | (vi) 6way horizontal TPN MCB DB (Double door):- |
| 320 | Supplying & installation of 10 KA breaking capacity, B/C curve MCB of following ratings in the existing MCB DB including connectionas required:- |
| 321 | (i) 6 to 32 amps SP MCB:- |
| 322 | (ii) 6 to 32 amps DP MCB:- |
| 323 | (iii) 40/50/63 amps FP MCB:- |
| 324 | (iv) 6 to 32 amps FP MCB:- |
| 325 | (v) 6 to 32 amps TP MCB:- |
| 326 | Earthing with 40 mm dia G.I. Earth pipe (medium gauge) 4.5 m. long complete with masonry enclosure on top CI cover plate size 12"x 12" having locking arrangement including CC work, holes on earth pipe etc. as required. |
| 327 | Extra for using salt (5 kg) and charcoal (46kg) for pipe earth electrode as required. |
| 328 | Proving and fixing / drawing of 4.06 mm dia (8 SWG) G.I. wire on surface or in existing G.I/ PVC/ Polythene pipe for loop earthing as required. |
| 329 | Supplying and fixing of the following sizes wooden switch boards with 3mm thick bakelite cover etc. as required. |
| 330 | (i) 300mm x 380mm (12" X 15") :- |
| 331 | Supplying &fixing of 12mm thick marine plywood conforming to IS:710 with necessary painting etc as required:- |
| 332 | Supplying and fixing of following vertical storage water heater 5 star catagorycomplete with 15 amps top, connection pipes including necessary connection etc as required. |
| 333 | (i) 15 litre storage capacity:- |
| 334 | Suppiying & fixing of UTP- 4 Pair Cat- 6E LAN Cable in existing PVC conduit i/c necessary connection etc as required. |
| 335 | Supplying & installation of Surge Protection Device (SPD) of following ratings in the existing Panels/MCB DBs including necessay connections etc as required:- |
| 336 | (i) Surge Protection Device (SPD, withdrawable) (Type-2) with Imax 15 KA (3P+N) :- |
| 337 | (ii) Catridge for Surge Protection Device (SPD) (Type-2) with Imax 15 KA (3P+N) :- |
| 338 | Supplying and installation of Bus bar chamber of the following ratings and sizes made of steel sheet enclosure with all accessories including necessary connection etc. as required:- |
| 339 | (i) 32 amps 415 volts four strip Copper busbar chamber 4 ways of size (300mmx240mmx80mm):- |
| 340 | Supplying and laying of the following sizes XLPE insulated PVC sheathed aluminium conductor armoured cable with necessary connection etc as required |
| 341 | (i) 2 core 4 Sq mm |
| 342 | Excavation of earth for cable trench of 800mm depth & 300mm width in all kinds of soil including back filling of cable trench with the excavated soil with 20cm layer of sand, 3.5 nos bricks per metre for protection including ramming, consolidating to the original shape as per dirrection of Site Engineer |
| 343 | Drawing of armoured/un-armoured cable with proper saddling etc as required |
| 344 | SUB HEAD : INTERNAL ROAD WORK |
| 345 | Excavation in Soil using Hydraulic Excavator and Tippers with disposal upto 1000 m Excavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections and transporting to the embankment location with all lifts and lead upto 1000 m as per MoRD Technical Specification Clause 302.3. |
| 346 | Compacting Original Ground Compacting original ground supporting subgrade Loosening of the ground upto a level of 300 mm below the subgrade level, watered, graded and compacted in layers to meet requirement of Tables 300.1 and 300.2 for subgrade construction as per MoRD Technical Specification Clause 303.5.2. |
| 347 | Granular Sub-base with Well Graded Material (Table 400.1) (A) By Mix in Place Method Construction of granular sub-base by providing well graded material spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per MoRD Technical Specification Clause 401. i). For Grading I Material |
| 348 | Water Bound Macadam Sub-Base / Base a). WBM Grading 2 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kNin stages to proper grade and camber, applying and brooming, stone screening/ binding materials to fill up the interstices of coarse aggregate, watering and compacting to the required density "Grading 2" as per MoRD Technical Specification Clause 405. (A) By Manual Means |
| 349 | Water Bound Macadam Sub-Base / Base b). WBM Grading 3 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kNin stages to proper grade and camber, applying and brooming, stone screeningto fill up the interstices of coarse aggregate, watering and compacting to the required density "Grading 3" as per MoRD Technical Specification Clause 405. (A). By Manual Means |
| 350 | Tack coat using hot straight run bitumen of grade VG-30 on W.B.M. Providing and applying tack coat using hot straight run bitumen of grade VG-30, including heating the bitumen, spraying the bitumen, cleaning and preparing the existing road surface as per specifications:On W.B.M. @ 0.75 kg/ sqm. |
| 351 | Bituminous Macadam Providing and laying bituminous macadam with hot mix plant using crushed aggregates of grading as per Table 500.4 premixed with bituminous binder, transported to site upto a lead of 1000 m laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled to achieve the desired compaction as per MoRD Technical Specification Clause 504. i). With Viscosity Graded Bitumen of VG-30. |
| 352 | 20 mm thick Open-Graded Premix Carpet using Bituminous (Viscosity grade/ modified bitumen) Binder Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using Viscosity grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base , including mixing in a suitable plant, laying and rolling with a three wheel 80 - 100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C or Type D as per MoRD Technical Specification Clause 508. Case - II : By Mechanical Means I). Bitumen of VG-30 |
| 353 | Seal Coat Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A or Type B or Type C or Type D as per MoRD Technical Specification Clause 510. A. By Manual Means Case - IV : Type D (premix with fine sand) (I). Bitumen of VG-30 |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
