Military Engineer Services-MES has published Tender For Addn/Altn Of 134 Jco And Or Pre Map Md Accn At Abohar Mil Stn (Job No 10Camwp/2022-23/01). Submission Date for this Tender is 05-06-2023. Kitchen Equipment Tenders in abohar Punjab. Bidders can get complete Tender details and download the document.
| Sr No | CorrigendumDate | Corrignedum | CorrigendumType | NewSubmissionDate |
| 1 | 17-Jan-2023 | Corrigendum 01 | Date | 27-02-2023 |
| 2 | 11-Feb-2023 | Corrigendum2 | Date | 13-03-2023 |
| 3 | 24-Feb-2023 | Corrigendum 03 | Date | 29-03-2023 |
| 4 | 15-Mar-2023 | Corrigendun 04 | Date | 08-04-2023 |
| 5 | 24-Mar-2023 | Corrigendum5 | Date | 17-04-2023 |
| 6 | 05-Apr-2023 | Corrigendun 06 | Date | 24-04-2023 |
| 7 | 13-Apr-2023 | Corrigendun 07 | Date | 01-05-2023 |
| 8 | 21-Apr-2023 | Corrigendum 08 | Date | 11-05-2023 |
| 9 | 01-May-2023 | Corrigendum 09 | Date | 18-05-2023 |
| 10 | 08-May-2023 | Corrigendum 10 | Date | 23-05-2023 |
| 11 | 11-May-2023 | Corrigendum 11 | BOQ | 23-05-2023 |
| 12 | 15-May-2023 | Corrigendum 12 | Date | 29-05-2023 |
| 13 | 17-May-2023 | Corrigendum 13 | BOQ | 29-05-2023 |
| 14 | 29-May-2023 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 05-06-2023 |
| Sl. No. | Item Description |
| 1 | B/R PORTION |
| 2 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) areanot exceeding 1.50 sqm each and removing from site including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast complete all as specified and asdirected by Engineer-in- charge. |
| 3 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) areaexceeding 1.50 sqm but not exceeding 4 Sqm each and removing from site including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast complete all as specified and asdirected by Engineer-in- charge. |
| 4 | Taking down wooden shutters only of any description area exceeding 1.0 sqm and not exceeding 2.0 sqm each and refixing in same opening after necessary easing, adjustments, minor repairs, oiling, adjustment with cutting or fixing plain fillets/planks made from second class hard wood etc to remove gap between floor and shutter complete all as specified and as directed by Engineer-in- charge. |
| 5 | Supply & fixing aluminium sliding windowthree trackwith frame & two glass shutters using 4 mm thick glass tinted modi guard and oneshutter with stainless steel wire gauge wirecloth 0.31 mm nominaldia of wire and width of aperture 1.61 mm using aluminium powder coated section (minimum thickness of powder coating not less than 50 micron) including approved fittings like aluminium cleat, PVC track, bearing, handle lock, rubber beading etc complete all as specified and as directed by Engineer-in-Charge. Note:- Size of aluminium section of make Jindal main-2010 or equivalent in make mentioned in Appx A to PSS-II (Equivalency approved by GE) shall be as under :- (i)Three track top and vertical - Section No 20621. (ii) Three track bottom - SectionNo 20620 (iii)Shutter vertical section - Section 20604 (iv)Shutter top and bottom - Section 20604 (v) Shutter vertical middle (interlock) - Section 20605 (vi)Cost of Glass and wire cloth shall be included in the unit rate. |
| 6 | Supply & fixing aluminium anodised frame, made out of aluminium sectionpowder coated(minimum thickness of powder coating not less than 50 micron) for window, ventilators and aluminium partition with one or more rebates including joining cleat for fixing etc., the top and bottom horizontal members and vertical members adjacent walls shall be fixed with floor, ceiling walls and cills where required and fixing with the help of rawal plug and screw or with fixing clip or with expansion hold plate fasteners. Aluminium section shall be smooth, rust free, straight mitred and jointed mechanically where ever required complete all as specified and as directed by Engineer-in-Charge. Note :- The weight of each section shall be physically ascertained through a board of officers convened by GE and payment shall be made only after the actual weight at site. |
| 7 | Supply & fixing anodised aluminium window shutter (glazed or gauzed), side hung type without sash bars, made out of aluminium section weighing not less than 0.55 Kg/mtr, powder coated (minimum thickness of powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, anodised aluminium fittings (each shutter) such as peg stays 150mm long (1 No), hinges type B-21 100mm long (2 Nos) suitable handle (1 No.), complete all as specified and as directed by Engineer-in-Charge. Note :- Aluminium chowkhat/ frame, Glass, wiremesh and grill where required shall be measured and paid separately under appropriate item of BOQ. |
| 8 | Supply & fixing aluminium Powder coated grill weight not less than 1.50 kg/sqm in windows, ventilators including fixing material complete all as specified and as directed by Engineer-in-Charge. |
| 9 | Supply & fixing Fiber Glass Reinforced plastic (FRP) Door Frame of cross section 90mm x 45mm having single rebate of 32mm x 15mm to receive shutter of 30mm thickness. The laminate door frame moulded with two resistant grade unsaturated polyester plain and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame., complete all as specified and as directed by Engineer-in- charge. |
| 10 | Supply and fixing to existing door frames 30mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames, complete as specified by the manufacturer and as per directions of Engineer- in-charge. |
| 11 | Supply & fixing Factory made prefabricated Pressed steel Door frame made out of mild steel 1.25mm thick girth of frame 185mm including necessary MS rawl plug/bolts and fixing 75mm long butt hinges medium weight cold rolled mild steel etc and shutter including stiffeners made out of mild steel sheet 1.25mm thick cut to size, holes punched and welded seams including bending or turning up all around, mitred angle etc as required with Locking arrangement using mild steel mortise lock 4 levers with 2 Nos of keys of size 100mm (Make Godrej/Harison/Navtal) including MS chromium plated handle and 2 Nos MS locking rods out of 8 mm dia not exc 1000mm long fixed to mortise lock and handle with necessary bolts and nuts covered by MS sheet 1.25 mm thick complete including two coat of synthetic enamel paint over a shop coat of zinc chromate primer on interior surface (not -visible from front) and hammer tone paint on exterior surface ( visible from front) as per Godrej Pattern including taking out old shutter with frame complete all as specified and as directed by Engineer-in-charge. |
| 12 | Material and labour for providing kitchen cabinet and cubboard in required sizes at site made out of 18mm thick PVC sheet (prelam) having one side decorative laminated sheet (for shutter, back side of cabinet, sides of cabinet, partition and shelves etc). All the edges of shutter and front exposed edge of partition/shelves shall be covered with 2mm thick edge bonding tape as per manufacturer. Including all required fixing material such as SS brackets, screws, adhesive etc., including taking out old any type cabinet complete all as specified and as directed by Engineer-in-charge. Note :- (i) The area of each sheet (shutter, back side of cabinet, sides of cabinet, partition and shelves)shall be measured in sqm for payment. (ii)Magnetic catcher, handle/knob, continuous Piano hinges and PVC frame (where required) shall be measured and paid separately under appropriate item of BOQ. (iii) Any other material required for making/fixing/hanging of cabinet shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account. |
| 13 | Supply and fixing Magnetic catcher fixed with steel screw complete all as specified and as directed by Engineer-in-charge. |
| 14 | Supply and fixing 40mm dia, cupboard knobs brass, fixed with nut, screw and washer bright finish complete all as specified and as directed by Engineer-in-charge. |
| 15 | Supply & fixing Continuous (piano) hinges, stainless steel, bright finish, width of flap when open 30mm complete all as specified and as directed by Engineer-in-charge . |
| 16 | Supply and fixing Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as directed by Engineer-in-Charge. (Note :- Frame shall be elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life) |
| 17 | Supply and fixingfactory made pressed steel frames of size 125 x 60mm (thickness of sheet shall be 1.25mm) for doors with one or more rebates including necessary lugs and lock strike plate, etc. , including fixing only butt hinges suitable Nos as directed for each leaf, and making good the wall with plaster in CM 1:6 complete all as specified and as directed by Engineer-in- charge. Note : - Butt hinges shall be measured and paid separately under appropriate item of BOQ as supply only. |
| 18 | Supply and fixingfactory made pressed steel frames of size 105 x 60mm (thickness of sheet shall be 1.25mm) for doors with one or more rebates including necessary lugs and lock strike plate, etc. , including fixing only butt hinges suitable Nos as directed for each leaf, and making good the wall with plaster in CM 1:6 complete all as specified and as directed by Engineer-in- charge. Note : - Butt hinges shall be measured and paid separately under appropriate item of BOQ as supply only. |
| 19 | Material and labour for PCC (1:3:6) type C-1, using 20 mm graded aggregated as in back filling of pressed steel door frame/chowkhat and bed block for fixing of hold fast complete all as specified and as directed by Engineer-in-Charge |
| 20 | Supply & fixing factory made plain framed panelled shutter 35mm thick made out of 2nd class hard wood with lock rail and panel (two panels) inserts of 9mm BWP commercial ply. The size of rails and styles as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and as directed by Engineer-in- charge. |
| 21 | Supply & fixing factory made glazed and skeleton shutter 35mm thick made out of 2nd class hard wood kiln seasoned and chemically pressure treated, open rebated and prepared to receive glass, gauze, etc., but divided into squares, with plain chamfered or rounded, mitred and rebated sash bars, any numbers, fitted with cut and mitred beads for securing glass, gauze etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a);complete all as specified and as directed by Engineer-in- charge. |
| 22 | Supply only 100mm long stainless steel butt hinges heavy duty type B-21 complete all as specified and as directed by Engineer-in-charge. |
| 23 | Supply and fixing 100mm long stainless steel butt hinges heavy duty type B-21 including stainless steel screws complete all as specified and as directed by Engineer-in-charge. |
| 24 | Supply and fixing anodised aluminium handle cast type 150mm long complete all as specified and as directed by Engineer-in-charge. |
| 25 | Supply and fixing in replacement anodised aluminium handle cast type 150mm long complete all as specified and as directed by Engineer-in-charge. |
| 26 | Supply and fixing aluminium anodised barrel tower bolt of extruded section, 200mm longcomplete all as specified and as directed by Engineer-in-charge. |
| 27 | Supply and fixing in replacement aluminium anodised barrel tower bolt of extruded section, 200mm longcomplete all as specified and as directed by Engineer-in-charge. |
| 28 | Supply & fixingaluminium anodised sliding door bolts 300mm long, with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed by Engineer-in- charge. |
| 29 | Supply & fixing in replacement aluminium anodised sliding door bolts 300mm long, with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed by Engineer-in- charge. |
| 30 | Supply & fixing Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, Overall length of cover plate 150mm, complete all as specified and directed by Engineer-in-Charge. |
| 31 | Supply & fixingin replacement Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, Overall length of cover plate 150mm, complete all as specified and directed by Engineer-in-Charge. |
| 32 | Supply and fixing mild steel 300mm long rat tail rod pattern spring including roller and roller plate and fixing to frame with screw complete all as specified and as directed by Engineer-in- charge. |
| 33 | Supply & fixingin replacement mild steel 300mm long rat tail rod pattern spring including roller and roller plate and fixing to frame with screw complete all as specified and as directed by Engineer-in- charge. |
| 34 | Supply and fixing curtain rod 25mm dia MS pipe with ivory coloured PVC coated, wall thickness of pipe not less than 20 guage, including fancy type brackets and pair of decorated end knobs (finials), stop roller etc. as per site requirement, fixed to wall with fixing accessories, including taking down old existing curtain rods any description complete all as specified and as directed by Engineer-in-Charge. |
| 35 | Supply & fixing Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed complete all as specified and as directed by Engineer-in- charge |
| 36 | Supply & fixing in replacement Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed complete all as specified and as directed by Engineer-in- charge |
| 37 | Supply & fixing 4mm thick sheet glass ordinary quality in squares / retangular not exceeding 0.5sqm in each pane (aluminium window/ventilator) complete all as specified and as directed by Engineer-in- charge. Note :- Aluminium fittings and rubber beading for securing the glass shall be included in main item of aluminium window/ventilator of BOQ. |
| 38 | Supply & fixing, 4mm thick figured glass pin head type in squares / retangular not exceeding 0.5sqm in each pane complete all as specified and as directed by Engineer-in- charge. Note :- Aluminium fittings and rubber beading for securing the glass shall be included in main item of aluminium window/ventilator of BOQ. |
| 39 | Roughening surfaces of old concrete floor by picking, sweeping cleaning and washing down with water to remove dust etc. complete all as specified and as directed by Engineer-in-Charge. |
| 40 | Material and labour for Non Skid ceramic light coloured tiles7 to 8 mm thick squarearea of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floor, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile includingnecessary cutting as per site requirement, tiles laid over and including 15 mm thick bedding layer (screed bed) in cement mortar (1:6) and finish the surface rough to receive the tile complete all as specified and directed by Engineer-in-Charge. |
| 41 | Material and labour for Non Skid ceramic light coloured tiles 7 to 8mm thick square or rectangular as in skirting (cut from same size and type as floor tile ), dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile includingnecessary cutting as per site requirement, tiles laid over and including 10 mm thick bedding layer (rendering) in cement mortar (1:4) and finish the surface rough to receive the tile including making good plaster surfaces (above skirting tile) to match the existing complete all as specified and as directed by Engineer-in-Charge. |
| 42 | Demolition of floor hearth or wall tilling including cement mortar bedding but not backing including removing rubbish material from building and thrown in low lying empty area at any distance upto 500 metres from the site complete all as specified and as directed by Engineer-in-Charge. |
| 43 | Material and labour for Glazed ceramic coloured tiles light shade of size 300mmx 450mm, 7mm thick, as in vertical surface set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 10 mm thick bedding layer (rendering) in cement mortar (1:4) and finish the surface rough to receive the tile complete all as specified and as directed by Engineer-in-Charge. |
| 44 | Dismantling of Stone slabs of any description or thickness in floors, plateform, apron etc laid bedded and pointed in any mortarincluding removing rubbish material from building and thrown in low lying empty area at any distance upto 500 metres from the site complete all as specified and as directed by Engineer-in-Charge. |
| 45 | Material and labour 18-20mm thickness approved shade granite of minimum size equal to width of slab (not less than 610mm) machine cut, granite duly factory grinding and polishing and chamfering the outer edges (table rubbed and mirror polished) as in cooking platform and like laid over and including 20mm thick cement mortar (1:4) screed bed including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including accomodate the hole for gas pipe complete all as specified and as directed by Engineer-in-Charge. |
| 46 | Material and labour for machine cut 20 to 25 mm thick, Kota stone slab (size of slab not less than 550x450mm for flooring and in single piece for treads of staircase), laid over and including 20 mm thick bedding layer in cement mortar (1:6) and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing /grinding (mirror finish) andpolishing by machine, including machine cutting to make it square or rectangular as per site complete all as specified and as directed by Engineer-in-Charge. |
| 47 | Material and labour for machine cut 18mm thick, Kota stone slab as in skirting, dado and on pillar, laid over and including 10 mm thick bedding layer in cement mortar (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing /grinding (mirror finish ) and polishing by machine, including machine cutting to make it square or rectangularcomplete all as specified and as directed by Engineer-in-Charge. |
| 48 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided including removing rubbish material from building and thrown in low lying empty area at any distance upto 500 metres from the site complete all as specified and as directed by Engineer-in-Charge |
| 49 | Material and labour for water proofing treatment to sunken slab and adjoining vertical surfaces as per any one of the two method as specified in PSS-II respective clause of CA complete all as directed by Engineer-in-charge/GE. Note : (i) Work shall be executed through specialized agency (ii) The treatment shall be carried out as per the manufactures instructions and as directed by the Engineer in charge. The name of firm shall be got approved from CWE before carrying out the work. (iii) Only Plan area will be measured for payment. Treatment should be continue upto 450mm height on vertical walls. (iv) PCC filling under sunken area will be measured & paid separately. |
| 50 | Material & Labour for PCC (1:5:10) type E2 using 40mm graded stone aggregate as filling of sunken floors complete all as specified and as directed by Engineer-in-charge. |
| 51 | Material & Labour for 40 mm GI pipe medium grade, made to shape as in spout pipe 60cm long in sunken/ verandah/ Balcony including making hole and making good with cement mortar complete all as specified and as directed by Engineer-in-charge. |
| 52 | Dismantling brick terracing tiles single layer from roof laid and pointed in cement mortar ncluding cleaning and stacking serviceable tiles for re use and balance unserviceable tiles removing from the site complete all as specified and as directed by Engineer-in-charge. |
| 53 | Demolition/taking out of mud from roofs, any thickness, including removing / cutting uprooting grass, vegetations and roots of small plants etc on roof and surrounding/parapit wall etc, including removing rubbish material from building and thrown in low lying empty area (as per direcction of AGE) at any distance upto 500 metres from the site complete all as specified and as directed by Engineer-in-Charge |
| 54 | Material and labour for Preparing surface of top roof slab including sides of parapits and cleaned of all foreign materials such as fungues, moss, dust, loose particle etc by wire brushing, sprinkling water on the surface and ensure water does not stand anywhere. If it is so, the roof surface shall be leveled with cement mortar and after that surface shall be painted with one coat of cold applied bituminous primer @ 0.40 ltr per sqm, applied over primed surface APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt. not less than 150 gms/sqm) laid on primed surface by forced application, torching with overlaps as recommended by the manufacturer complete all as specified and as directed by Engineer-in-charge. |
| 55 | Material and labour for PCC ( 1:4:8) using brick aggregate as in roof minimum average thickness 75mm and increasing uniformly towards ridges to obtain a chain slope 1:40, the top shall be trowelled with the addition of jaggery solution and finished smooth complete all as specified and as directed by Engineer-in-charge. |
| 56 | Material and labour for 40mm thick brick tiles laid/bedded on screed bed 15mm thick in cement mortar (1:6), on existing lime concrete surfaces of roof,joints grouted flush in cement mortar (1:3) mixed with liquid WPC @ as per manufacturer instruction per bag of cement of 50kg and including flush pointing as work proceed with same material complete all as specified in clause 11.27.3 of MES Sch Part-I (2009) complete all as specified and as directed by Engineer-in-Charge. (Note :- Water proofing compound shall be measured & paid separately as Supply only) |
| 57 | Material and labour for 40mm thick brick tiles (old serviceable tiles obtained from demolition/dismantled itemshall be reused)laid/bedded on screed bed 15mm thick in cement mortar (1:6), on existing lime concrete surfaces of roof,joints grouted flush in cement mortar (1:3) mixed with liquid WPC @ as per manufacturer instruction per bag of cement of 50kg and including flush pointing as work proceed with same material complete all as specified in clause 11.27.3 of MES Sch Part-I (2009) complete all as specified and as directed by Engineer-in-Charge. (Note :- Water proofing compound shall be measured & paid separately as Supply only) |
| 58 | Material and labour for covering the crumple joint between walls, beams, columns by 0.56 mm thick Plain Aluminium sheeting,Alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing (length and girth as fixed) including fixing material and takig out old sheet complete all as specified and as directed. |
| 59 | Providing and injecting approved grout in proportion Stirrer mixed Acrylic Polymer of approved make @ 2% of weight of cement used modified cement slurry non shrinks compound in concrete/RCC work. Made with recommended by the manufacture into cracks/honey-comb area of concrete/masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of GE. Note :- The payment shall be made on the basis of actual weight of approved grout injected. |
| 60 | Material and labour for 75 mm thick PCC (1:3:6) type C-2 using 40mm graded mechanically crushed stone aggregate as in plinth protection finished even and smooth without using extra cement including 10mm wide, 30mm deep joints at the rate of 3.00 mtr centre to centre and at every turning point, filling the Joints withbituminous sealing compound of grade ‘A’/bitumen mastic filler/sealant complete all as specified and as directed by the Engineer-in-Charge. |
| 61 | Taking up or down existing galvanised steel water tubing (GI pipe) 15mm bore including fitting/connection from wall, ceiling, floor etc. complete all as specified and as directed by Engineer-in-charge. |
| 62 | Re-fixing old serviceable 15mm bore galvanised steel water tubing (GI pipe) but new fittings like elbow, tee, union, socket, reducer etc. in new or old portion/position to walls, ceiling, floor etc complete all as specified and as directed by Engineer-in-charge. (Note :- Old serviceable pipe obtained from taking up or down (here-in-before) item of this BOQ shall be reused after necessary cleaning internally and rerunning the old screw threads as required. |
| 63 | Supply and fixing galvanized steel tubing (GI pipe) medium grade 15mm bore ISI marked with all new fittings like elbow, tee, union, socket, reducer etc. and fixed complete to walls, ceiling or laid in floor including cutting and threading of pipe complete all as specified and as directed by Engineer-in- charge. |
| 64 | Taking up or down existing galvanised steel water tubing (GI pipe) 20mm bore including fitting/connection from wall, ceiling, floor etc. complete all as specified and as directed by Engineer-in-charge. |
| 65 | Re-fixing old serviceable 20mm bore galvanised steel water tubing (GI pipe) but new fittings like elbow, tee, union, socket, reducer etc. in new or old portion/position to walls, ceiling, floor etc complete all as specified and as directed by Engineer-in-charge. (Note :- Old serviceable pipe obtained from taking up or down (here-in-before) item of this BOQ shall be reused after necessary cleaning internally and rerunning the old screw threads as required. |
| 66 | Supply and fixing galvanized steel tubing (GI pipe) medium grade 20mm bore ISI marked with all new fittings like elbow, tee, union, socket, reducer etc. and fixed complete to walls, ceiling or laid in floor including cutting and threading of pipe complete all as specified and as directed by Engineer-in- charge. |
| 67 | Supply and fixing galvanized steel tubing (GI pipe) medium grade 40mm bore ISI marked with all new fittings like elbow, tee, union, socket, reducer etc. and fixed complete to walls, ceiling or laid in floor including cutting and threading of pipe complete all as specified and as directed by Engineer-in- charge. Note for item No 61 to 67 :- Cost for cutting chases/groove as required for concealed pipe as directed shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account. |
| 68 | Supply & fixing rotational mouldedpolyethylene water storage tank white colour of capacity 500 litres (cylindrical vertical, triple layered with closed top, ISI marked), hoisted and fixed in position including making inlet and out let connection including dismantling/taking down of existing unserviceable PVC water storage tanks of any description and capicity with float valve and gate valve complete all as specified and as directed by Engineer-in-charge. |
| 69 | Supply and fixing ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball (polythene float) complete, screwed suitable for 20mm bore iron pipe complete all specified and as directed by Engineer-in-charge. Note :- The minimum weight of ball valve shall be as given in SSR or in relevant IS. |
| 70 | Supply and fixing gun metal, globe or gate valve (ISI marked), with iron wheel head, screwed both ends suitable for 20mm bore iron pipes complete all as specified and as directed by Engineer-in-charge. Note :- The minimum weight of gate valve shall be as given in SSR or in relevant IS. |
| 71 | Supply and fixing in replacement bib tap with Wall Flange cast copper alloy, chromium plated, fancy type, long body, with round head/knob, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified & directed by Engineer-in-charge.Cat part No CON-107KN of Jaquar or Techno commercial equivalent in make mentioned in Appx "B" |
| 72 | Supply and fixing in replacement 15 mm bore chromium plated Angle stop valve with Wall Flange of cast copper alloy chromium plated, fancy typewith round head/knob, screwed down high pressure screwed end for iron pipe or for unions and fixed complete all as specified and as directed by Engineer-in-charge. Cat part No CON-059KN of Jaquar or Techno commercial equivalent in make mentioned in Appx "B" |
| 73 | Supply and fixing central hole Single Lever Basin Mixer, 15mm bore, chromium plated, for mixing hot & cold water, complete with fittings, 450mm long braided hoses with connection and nut for WHB including taking out old any type pillar cock/mixer complete all as specified and as directed by Engineer-in-charge. Cat part No VGP-81011B of Jaquar or Techno commercial equivalent in make mentioned in Appx "B" |
| 74 | Supply and fixing central hole basin mixer valve with regular spout, 15mm bore, brass chromium plated, for mixing hot & cold water, complete with fittings, 450mm long braided hoses with connection and nut for WHB including taking out old any type pillar cock/mixer complete all as specified and as directed by Engineer-in-charge. Cat part No CON-167KNB of Jaquar or Techno commercial equivalent in make mentioned in Appx "B" |
| 75 | Supply and fixing in replacement mixer valve with swinging spout (for sink) 15mm bore, brass chromium plated, for mixing hot & cold water, screwed down for iron pipe suitable for fixing to wallcomplete all as specified and as directed by Engineer-in-charge. Cat part No CON-CHR-309KNM of Jaquar or Techno commercial equivalent in make mentioned in Appx "B" |
| 76 | Supply and fixing in replacement chromium plated, Wall Mixer with provision for overhead Shower with 115mm Long Bend Pipe On Upper Side, Connecting Legs & Wall Flanges, screwed ends suitable for15mm bore iron pipe, complete all as specified and as directed by Engineer-in-charge. Cat part No CON-273KNUPR of Jaquar or Techno commercial equivalent in make mentioned in Appx "B" |
| 77 | Supply and fixing in replacement Kitchen Rack / Dish Rack (Kitchen Stand or wall mounted) of size750mmx600mmx250mm (Appx size) made out of Food Grade Stainless Steel 1mm thick sheet/strip including necessary arrangements for plates and utencils to keep (Holds up to many plates or bowls To accommodate several place settings, Multipurpose), stylish modern streamline design, rust resistant, easy to assemble and clean including fitting accessories complete all as directed by Engineer-in-charge. |
| 78 | Supply & fixing in replacement stainless steel sink with drainageboard made out of 1.00mm thick sheet , kitchen or laboratory withplugs, washers, waste pipe includingbedding in cement mortar to dwarf wall or fixing cast iron cantilever brackets and connecting union to waste pipe; overall size 915mm x 460mm with bowl size 405mm x 355mm x 200mm including taking down existing chinaware sink complete all as specified and directed by Engineer-in-Charge. |
| 79 | Supply & fixing in replacement vitreous china Oval Shape Slim/Thin Rim Ceramic Wash Basin, white, flat back of size 550mm x 400mm, Counter top/table top including 32mm chromium plated waste coupling and PVC waste pipe including fixing material for wash basin on granite slab and including making hole in granite slab for coupling, complete all as specified and as directed by Engineer-in-Charge. |
| 80 | Supply & fixing in replacement corner vitreous china wash basin, white, flat back of size 450mm x 390mm, including 32mm chromium plated waste coupling and PVC waste pipe including bracket and cutting for and pinning in end of bracket or erecting with long screwed shanks & fly-nuts, flange end bedded in red lead cement, complete all as specified and as directed by Engineer-in-Charge. |
| 81 | Supply & fixing in replacement 300 mm long PVC connection 15mm size with brass nuts complete all as specified & directed by Engineer-in-charge. |
| 82 | Supply & fixing in replacement 450 mm long PVC connection 15mm size with PTMT nuts complete all as specified & directed by Engineer-in-charge. |
| 83 | Supply & fixing in replacement vitreous China squatting pan "Orissa" pattern white of size 580mmx440mm white with integral foot rests, excluding flushing cistern, flush pipe above floor but including setting the trap and pan in lime concrete (1 lime, 2 sand or surkhi and 5 aggretate), min. 150mm thick all round and finished just below level of rim of pan to receive the floor finishing, including PVC flush pipe upto finished floor level, joints of flush pipe and trap make leakproof and testing upto entire satisfaction of Engineer-in-charge before filling concrete complete all as specified and as directed by Engineer-in- charge. |
| 84 | Supply and fixing in replacement PVC low level cistern of 10 ltrs capacity with top push button inclusive of brackets and PVC bend long type and connection to flush pipe of any size and pattern with inlet ball valve float and handle complete all as specified and directed by Engineer-in-Charge. |
| 85 | Supply & fixing in replacement cromium plated swivel shower of any colour with shower arm 15 mm size,195 mm long with bend of 45 degree with flange of any colour for fixing with 15mm dia pipe complete all as specified and as directed by Engineer-in-charge. Note :- The minimum weight 40gms. |
| 86 | Supply and fixingin replacement PVC Bathroom mirror cabinet of appx size 450mm X 350mm X 140mm (Compact Mirror Cabinet, Concealed shelves) approved quality complete all as specified and as directed by Engineer-in-charge. |
| 87 | Supply and fixingin replacement chromium plated Towel Ring Round with Round Flange, fixed on wall with chromium plated brass screws and PVC plug complete all as specified and as directed by Engineer-in-charge. Cat part No ACN-1121BN of Jaquar or Techno commercial equivalent in make mentioned in Appx "B" |
| 88 | Supply and fixingin replacement chromium plated Soap Dish Holder with Round Flange, fixed on wall with chromium plated brass screws and PVC plug complete all as specified and as directed by Engineer-in-charge Cat part No ACN-1131N of Jaquar or Techno commercial equivalent in make mentioned in Appx "B" |
| 89 | Supply and fixingin replacementcorner PVC shelf assembly fancy type with brackets, fixed with brass screws and PVC plug complete all as directed by Engineer-in-charge. |
| 90 | Taking down eaves gutters and rain water PVC/CI pipes ( any size or pattern) including all fittings, heads, shoes, bends, swan-neck etc ( measured overall as fixed along the centre line over fittings and accessories) complete as specified and as directed by Engineer-in- charge |
| 91 | Supply & fixing 110mm bore PVC (SWR) pipes single socketed(pressure rating not less than 4kg/sqcm) in any length with rubber ring joints for drain or rain water fixed along walls with and including PVC stack clamps (interval of 1m) of suitable size, complete all as specified and as directed by Engineer-in- charge. |
| 92 | Supply & fixing 75mm bore PVC (SWR) pipes single socketed(pressure rating not less than 4kg/sqcm) in any length with rubber ring joints for drain or rain water fixed along walls with and including PVC stack clamps (interval of 1m) of suitable size, complete all as specified and as directed by Engineer-in- charge. |
| 93 | Supply & fixing PVC (SWR) bends (any radius) suitable for 110mm bore pipe complete all as specified and as directed by Engineer-in- charge. |
| 94 | Supply & fixing PVC (SWR) bends (any radius) suitable for 75mm bore pipe complete all as specified and as directed by Engineer-in- charge. |
| 95 | Supply & fixing PVC (SWR) junction single, (Single T) equal or unequal with access door suitable for 110mm bore pipe complete all as specified and as directed by Engineer-in- charge. |
| 96 | Supply & fixing PVC (SWR) junction single, (Single T) equal or unequal with access door suitable for 75mm bore pipe complete all as specified and as directed by Engineer-in- charge. |
| 97 | Supply & fixing PVC (SWR) vent cowl suitable for 75mm bore pipe complete all as specified and as directed by Engineer-in- charge. |
| 98 | Supply & fixing PVC (SWR) multi floor trap including jointing with solvent cement suitable for 75mm bore pipe complete all as specified and as directed by Engineer-in- charge. |
| 99 | Supply & fixing stainless steel Grating 125 mm dia with or without waste hole complete all as specified and as directed by Engineer-in- charge. |
| 100 | Supply & fixing 32mm bore High density polyethylene pipes (HDPE) of pressure rating not less than 6kg/sqcm laid in floors/trenches complete all as specified and as directed by Engineer-in- charge. Note :- (i) Excavation, earth work if required, shall be measured & paid separately under appropriate item of this Schedule.) |
| 101 | Excavation in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundations, shafts, wells, cess pits, manholes, for taking out old pipe and laying new pipe line, for laying cable etc. not exceeding 10 Sqm on plan and getting out in soft/loose soil including trimming the sides and forming bottom surfaces to required levels complete all as specified and as directed by Engineer-in-charge. |
| 102 | Returning filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm thick complete all as specified and as directed. |
| 103 | Removing excavated material (surplus soil) to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed by Engineer-in-charge. |
| 104 | Material and labour for PCC ( 1:4:8),type D-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and as directed by Engineer-in-charge. |
| 105 | Material and labour for PCC (1:2:4), type B-1 using 20 mm graded stone aggregate as in coping, mud stops, packing sides/around of interlocking tiles, bed block, for embedded posts & similar work etc including weatherings, slightly rounded or chamfered angles complete all as specified and as directed by Engineer-in-charge. |
| 106 | Material and labour for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment of voids in masonry using chemical emulsion@ one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and as directed by Engineer-in-charge. |
| 107 | Material and labour for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre 300mm apart including drilling depth of holes not less than 300mm and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and as directed by Engineer-in-charge. |
| 108 | Taking down cement or cement lime plaster from brick wall etc including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge. |
| 109 | Material and labour for internal plastering 15mm thick in cement mortar (1:6) on any face of Brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge. |
| 110 | Material and labour for rendering/plastering 15mm thick on any face of Brick wall or concrete surfaces consisting in two layers i.e. first layer 10mm thick in cement mortar (1:4) and second (top layer) layer 5mm thick in cement mortar (1:4) including mixing of liquid WPC in mortar @ as per manufacturer instruction per bag of cement of 50kg, finished even and smooth without using extra cementcomplete all as specified and as directed by the Engineer-in-Charge.(Note :- WPC shall be measured & paid separately as Supply only) |
| 111 | Material and labour for Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster (1:4) (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster (1:1/2:2) (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete as specified and as directed by Engineer-in-Charge. Note :- Grooves shall be measured & paid separately |
| 112 | Material and labour for Forming groove of uniform size 12mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as specified and as directed by Engineer-in-Charge. |
| 113 | Supply only liquid water proofing compound complete all as specified and as directed by the Engineer-in-Charge. |
| 114 | Dismantling of brick work or stone / boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, in any description including cleaning and stacking serviceable brick for re use and balance removing rubbish from the site complete all as specified and as directed by Engineer-in-charge. |
| 115 | Material and labour for brick work(old serviceable bricks obtained from dismantled itemshall be reused ) straight or curved on plan exc. 6 metre mean radius built in cement mortar (1:6) complete all as specified and as directed by Engineer-in-charge. |
| 116 | Material and labour for brick work with sub class ‘B’ old size burnt clay bricks, straight or curved on plan exc. 6 metre mean radius built in cement mortar (1:6) complete all as specified and as directed by Engineer-in-charge. |
| 117 | Material and labour for brick workin half brick thick wall straight or curved on plan exc. 6 metre mean radius built in cement mortar (1:4) complete all as specified and as directed by Engineer-in-charge. |
| 118 | Surface dressing not exceeding 15cm deep in soft/ loose soilincluding cutting of grass, roots, bushes if any and filling of lower portion with soil obtained from cuttingafter sepration of grass, roots, bushes etc and dressing and removing from site all grass, roots and extra soil if any complete all asspecified and as directed by Engineer-in-Charge. |
| 119 | Material and labour for 75mm thickcement concrete ( 1:4:8),type D-2 using 40 mm graded stone aggregate as in sub base complete all as specified and as directed by Engineer-in-charge. |
| 120 | Supply and laying/fixing 60 mm thick (M35 grade) precast interlocking tile/paving block factory made chamfered edge (made by using PU moulds on Vibrating Table Machine) using cement concrete and pigment, prepolished & preglazed, with approved colour, design & pattern as in foot parth, parks, lawns, drive ways or light traffic parking etc., laid in required colour & pattern, over and including 50mm thick compacted bed of fine sand cushining, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand and complete all as specified and as directed by Engineer-in-Charge. |
| 121 | Supply and laying factory made kerb stone of M-25 grade cement concrete laid in position to the required line, level and curvature, jointed with cement mortar (1:3) (1 cement:3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete all as specified and as directed. |
| 122 | Demolition of cement concrete reinforced of any description such as slab/OHT staging, kitchen chimeny, chajjas, fins, shelves, OHT etc, including reinforcement cut as required to facilitate demolition and prepare the surface to casting/jointing newincluding removing rubbish material from building and thrown in low lying empty area at any distance upto 500 metres from the site complete all as specified and as directed by Engineer-in-Charge |
| 123 | Material and labour for reinforced cement concrete M-25 (Design mix) using 20mm graded stone aggregate as in slabs supported on walls, beams and columns landing, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed by Engineer-in-Charge. (NOTE : Reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule. |
| 124 | Material and labour for reinforced cement concrete M-25 (Design mix) using 20mm graded stone aggregate as in louvers, parapets, railing and like complete all as specified and as directed by Engineer-in-Charge. (NOTE : Reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule. |
| 125 | Material and labour for reinforced cement concrete M-25 (Design mix) using 20mm graded stone aggregate as in chajjas, fascias, fins and like complete all as specified and as directed by Engineer-in-Charge. (NOTE : Reinforcement and form work shall be measured and paid for separately under appropriate item of this schedule. |
| 126 | Material and labour for mild steel TMT bars 10mm dia & over cut to length bent to shape, required including cranking, bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed by the Engineer-in-Charge. (NOTE : Weight of binding wire shall not be considered for measurement and payment purpose.) |
| 127 | Material and labour for mild steel TMT bars 6 to 8 mmdiacut to length bent to shape, required including cranking, bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed by the Engineer-in-Charge. (NOTE : Weight of binding wire shall not be considered for measurement and payment purpose.) |
| 128 | Material and labour for mild steel TMT bars 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders cut to length, bent to shape required including bending, cranking etc and binding with and including MS wire (annealed) not less than 0.9mm dia, complete all as specified & directed by Engineer-in- charge. (NOTE : Weight of binding wire shall not be considered for measurement and payment purpose) |
| 129 | Form work to soffits of suspended slabs such as flat roof slabs, floor slabs, shelf slab, landings and similar work not exceeding 200mm thick (horizontal or sloping) rough finished complete all as specified and as directed by Engineer-in- charge. |
| 130 | Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc. vertical or to batter rough finished complete all as specified and as directed by Engineer-in- charge. |
| 131 | Form work tochullah hoods, chajjas, troughs and similar items including edgesrough finished complete all as specified and as directed by Engineer-in- charge. |
| 132 | Form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10cm wide rough finished complete all as specified and as directed by Engineer-in- charge. |
| 133 | Shotcreting average thickness 25mm in RCC columns, beams and slab etc. (with mix minimum cement content of 350 Kg per Cum, M-25). Concrete having the specified minimum characteristic compressive strength (with ordinary portland cement, coarse sand and graded stone aggregates of 6mm maximum size) incl the cost of centering and shuttering at edges and corner etc as directed by Engr-in-Charge incl chipping of unsound/week concrete material 25mm average thickness from slabs, beams/columns etc with mannual Chisel or standard power driven percussion type all of approved makes incl tapering of all edges, making square shoulder of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes and throughly washing with water and allowing it to dry etc incl removel of rust by applying approved rust remover chemical and the coating with Dr Fixit Epoxy zinc primer @ 6 Sqm per Litre at DFT of 100 micron as per manufacturer"s instruction and specification, including removing rubbish material from building and thrown in low lying empty area at any distance from the site as directed complete as specified and as directed by Engineer-in-Charge. Make :- Sika / Fosroc/Pidilite or Techno commercial equivalent make approved by GE in writing from E-in-C"s approved list. Note : Complete treatment to be executed by approved applicator. |
| 134 | Supply and fixing hard drawn steel wire fabric not exc 4kg/sqm cut to lengths, wire mesh to be fixed and firmly anchored to the concrete surface by means of"L" shaped mild steel shear key welded with existing reinforcement including cost of material, labour, tools and plants incl welding/L-clip/tying with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed. |
| 135 | Material and labour for rendering 5mm thick in cement mortar (1:3) on surface of ceiling after shotcreting treatment, finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge. |
| 136 | Dismantling wrought iron or mild steel work of any description complete all as specified and as directed by Engineer-in- charge. |
| 137 | Excavation in post holes in soft/loose soil n. exc 0.50 cum each, getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers n. exc 25 cm including removing of surplus spoil to a distance n exc 50 mtr and making good the disturbed surfaces all as specified and directed by Engineer-in-Charge. |
| 138 | Material and labour for PCC (1:3:6), type C-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete, in post hole, bed block& similar work etc including form work complete all as specified and as directed by Engineer-in-charge. |
| 139 | Material and labour for mild steel Framed work such as grills, ladder, cooler stand, cloth drying provision, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similar work conforming to Fe.290.Gde-E-165complete all as specified and as directed by Engineer-in- charge. |
| 140 | Material and labour for structural steel work, framed work made by using rolled mild steel Joist, channel, angle, or tee sections, fixed independently distance pieces, cleats or other connecting plates, gusset plates, brackets, bending and welding, riveting etc, and cut to shape, drilled and counter sunk for screw, conforming to Gde Fe-410-W (Gde E-250 quality A)complete all as specified and as directed by the Engineer-in-Charge. |
| 141 | Cutting out concrete blocks, slabs, brickwork or stone masonry (in alter nate course), forming tooth-ings for and bonding new work in mortar into old work, including new materials entering old wall ie PCC (1:3:6) type C-1 using 20mm graded stone aggregate and set in cement mortar (1:6) complete all as specified and as directed by Engineer-in-charge. |
| 142 | Supply and fixing 4mm dia galvanised iron wire fitted with nut bolts complete all as specified & directed by Engineer-in- charge. |
| 143 | Material and labour for preparation ofnew steel and iron surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engineer-in- charge. |
| 144 | Material and labour for Preparation ofnew wooden or wood based surfacesof any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by Engineer-in- charge. |
| 145 | Material and labour for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth by cleaning the dust and removing all loose particle with using sanded paper, clean cloths and dry paint brush & applying two coats of synthetic enamel paint (1st quality) of approved tint/colour to achieve glossing finish with using paint brush complete as specified and as directed by Engineer-in-Charge. |
| 146 | Material and labour for preparation of old painted wooden surfaces of any description not otherwise described over 10cm width or girth by cleaning the dust and removing all loose particle with using clean cloths and dry paint brush & applying two coats of synthetic enamel paint (1st quality) of approved tint/colour to achieve glossing finish with using paint brush complete as specified and as directed by Engineer-in-Charge. |
| 147 | Material and labour for Preparation ofnew plastered Internalwall surface by sand papering or by any other mean and after preparing the surfaces applying the following complete all as specified and as directed by Engineer-in-charge:- (a)Applying Wall care putty in two coats on wall surface and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as directed. (b)Two coats of acrylic emulsion of approved tint over a coat of primer by using paint brush / Roller. |
| 148 | Material and labour for Preparation ofnew plastered external wall surface by sand papering or by any other mean and after preparing the surfaces applying the following complete all as specified and as directed by Engineer-in-charge:- (a)Applying Wall care putty in two coats on wall surface and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as directed. (b)Two coats of exterior acrylic emulsion of approved tint over a coat of primer by using paint brush / Roller. |
| 149 | Material and labour for Preparation ofnew plastered or concrete surface of ceiling surface by sand papering or by any other mean and after preparing the surfaces applying the following complete all as specified and as directed by Engineer-in-charge:- (a)Three coats of white wash by using paint brush. |
| 150 | Material and labour forPreparation of old decorated surfaces (plastered / unplastered) of ceiling by remove / scraping down allsmoke soot, moulds, moss & efflorescent salts, oil & greasy spots etc with using broom /steel patti / wire brush / sand papering or by any other mean including applyingwall care putty where required for filling to depressions/nail holes/light cracks etc and to make surface even and smooth, and after preparing the surface smooth applying One coat of lime white wash with paint brush complete all as specified and as directed by Engineer-in-Charge. |
| 151 | Material and labour for complete removal of existing treatment on Old Internal wall surfaces of any desciption, preperation of surface by Mechanised sander having suction vaccum Bag using Smart periodical methodology and after preparing the surfaces applying the following complete all as specified and as directed by Engineer-in-charge:- (a) Applying Wall care putty in two coats 1.5 mm thick each for filling to depression of scraped surface/nail holes/light cracks etc and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as directed. (b) Two coats of acrylic emulsion of approved tint over a coat of primer on old prepared surface by using paint brush / Roller. Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-chrge in case of places where using of Mechanical equiment are not posiible. |
| 152 | Material and labour for complete removal of existing treatment on Old external wall surfaces of any desciption, preperation of surface by Mechanised sander having suction vaccum Bag using Smart periodical methodology, complete all as specified and as directed by Engineer-in- charge and applying the following:- (a) Applying Wall care putty in two coats 1.5 mm thick each for filling to depression of scraped surface/nail holes/light cracks etc and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as directed. (b) Two coats of exterior acrylic emulsion of approved tint over a coat of acrylic emulsion external primer on old prepared surface by using paint brush / Roller. Note : Contractor may use manual scraping tools for complete removal and surface prepration with prior approval of Engr-in-chrge in case of places where using of Mechanical equiment are not posiible. |
| 153 | Material and labour forPreparation of old decorated surfaces (plastered/unplastered) of walls/pillars /cornices by remove / scraping down allsmoke soot, moulds, moss & efflorescent salts, oil & greasy spots etc with using broom /steel patti / wire brush / sand papering or by any other mean and after preparing the surfaces applying the following complete all as specified and as directed by Engineer-in-charge:- (a) Applying Wall care putty where required for filling to depression of scraped surface/nail holes/light cracks etc and smoothening the surfcae with sand papers / Mechanised sanding etc prepatory to paint as directed. (b) Two coats of acrylic emulsion of approved tint on old prepared surface by using paint brush / Roller. |
| 154 | B/R PORTION |
| 155 | Taking down carefully existing copper/aluminium point wiring (light/fan/sockets/bell/power point) complete with all accessories such as switch socket with sheet, ceiling rose, lamp holder including rusted/broken concealed conduit, junction and sunken boxes etc and removing dismantled material and making good disturbed surface of walls/floors etc matching with existing surface complete all as specified and as directed by Engineer-in-Charge. |
| 156 | Material and labour for concealed Point wiring for one light point/fan point controlled by one switch (using red, black and green etc colour wires as colour coding) complete with 1.5 Sqmm (nominal cross section area)single core FRLSH PVC insulatedunsheathed and multi strand copper conductor cable 1100 volt (ISI marked)drawn through andincludingPVC conduit 20mm dia (medium duty, ISI marked) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction boxes etc., including 2mm thick galvanised steel pressed sunken terminal boxes (Min 60mm deep, suitable size) concealed in wall, including 3mm thick bakelite plastic laminated sheet top cover for sunken boxes flush to surface for mounting of switches / socket / regulator etc, including provn of 1.5 Sqmm single core FRLSH PVC insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls/ceiling/floors etc. by using CM (1:3)complete all as specified and as directed. (switches/ socket / regulator shall be measured and paid separately under appropriate item of BOQ/Sch "A"). |
| 157 | All as per above Srl item No. 156 but for onesocket out let 5 Amps point controlled by one switch (on same board) complete all as specified and as directed by Engineer-in-charge. (switches, sockets etc. shall be measured and paid separately under appropriate item of BOQ/Sch A). |
| 158 | All as per above Srl item No. 156 but for one socket out let 5 Amps point controlled by one switch (on independent board and not below the any other switch board) complete all as specified and as directed by Engineer-in-charge. (switches , sockets etc. shall be measured and paid separately under appropriate item of BOQ). |
| 159 | All as per above Srl item No. 156 but for call bell point (on independent board) complete all as specified and as directed by Engineer-in-charge. (switches shall be measured and paid separately under appropriate item of BOQ). |
| 160 | Material and labour for concealed Point wiring for one light point controlled by two Nos- two way switch (using red, black and green colour wires as colour coding) complete with 1.5 Sqmm(nominal cross section area) single core FRLSH PVC insulatedunsheathed and multi strand copper conductor cable 1100 volt (ISI marked)drawn through andincludingPVC conduit 20mm dia (medium duty, ISI marked) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction box etc, including 2mm thick galvanised steel pressed sunken terminal boxes (Min 60mm deep, suitable size) concealed in wall, including 3mm thick bakelite plastic laminated sheet top cover for sunken boxes flush to surface for mounting of switch, including provn of 1.5 Sqmm single core FRLSH PVC insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls/ceiling/floors etc. by using CM (1:3)complete all as specified and as directed. (switches shall be measured and paid separately under appropriate item of BOQ). |
| 161 | Material and labour for concealed Point wiring for onesocket out let 15/16 Amps point controlled by one switch (on independant board) (using red, black and green colour wires as colour coding) complete with 2.5 Sqmm (nominal cross section area)single core FRLSH PVC insulatedunsheathed and multi strand copper conductor cable 1100 volt (ISI marked)drawn through andincludingPVC conduit 20mm dia (medium duty, ISI marked) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction box, including 2mm thick galvanised steel pressed sunken terminal boxes of (Min 60mm deep, suitable size) concealed in wall, including 3mm thick bakelite plastic laminated sheet top cover for sunken boxes flush to surface for mounting of switches / socket, including provn of 2.5 Sqmm single core FRLSH PVC insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls/ceiling/floors etc. by using CM (1:3)complete all as specified and as directed. (switch, socket shall be measured and paid separately under appropriate item of BOQ). |
| 162 | Material and labour for concealed Point wiring for onesocket out let 15/16 Amps point controlled by one switch (on independant board) (using red, black and green colour wires as colour coding) complete with 4 Sqmm (nominal cross section area)single core FRLSH PVC insulatedunsheathed and multi strand copper conductor cable 1100 volt (ISI marked)drawn through andincludingPVC conduit 20mm dia (medium duty, ISI marked) with all fittings and all accessories i.e. pipe bend, pipe hook, elbow, junction box, including 2mm thick galvanised steel pressed sunken terminal boxes of (Min 60mm deep, suitable size) concealed in wall, including 3mm thick bakelite plastic laminated sheet top cover for sunken boxes flush to surface for mounting of switches / socket, including provn of 4 Sqmm single core FRLSH PVC insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. including cutting chases in wall and making good disturbed surfaces of walls/ceiling/floors etc. by using CM (1:3)complete all as specified and as directed. (switch, socket shall be measured and paid separately under appropriate item of BOQ). |
| 163 | Taking down carefully existing copper/aluminium point wiring (light/fan/sockets points ) complete with all accessories such as switch with sheet, ceiling rose including rusted/broken concealed sunken boxes etc but except concealed conduit and junction boxes and removing dismantled material and making good disturbed surface of walls/floors etc matching with existing surface complete all as specified and as directed by Engineer-in-Charge. |
| 164 | Material and labour for concealed Point wiring for one light point/fan point /bell point controlled by one switch (using red, black and green colour wires as colour coding) complete with 1.5 Sqmm (nominal cross section area)single core FRLSH PVC insulatedunsheathed and multi strand copper conductor cable 1100 volt (ISI marked)drawn through existing PVC conduit but including 2mm thick galvanised steel pressed sunken terminal boxes of suitable size (Min 60mm deep, suitable length) concealed in wall, 3mm thick bakelite plastic laminated sheet top cover for sunken boxes flush to surface for mounting of switches / socket / regulator etc, including provn of 1.5 Sqmm single core FRLSH PVC insulated multi strand copper conductor wire continues as earth wire connected to earth dolly etc. complete all as specified and as directed. (switches, regulator shall be measured and paid separately under appropriate item of BOQ). Note:- Where ever it is not feasible to cable drawn through existing PVC conduit in roof salb (for ceiling fan point only) due to blocked, casing caping shall be provided by contractor without any extra cost, cost for the same shall deemed to be included in the quoted unit rate. |
| 165 | Supply and fixing switch piano flush type (ISI marked) , 5/6Amps, single pole, one way fixed on laminated sheet complete all as specified and as directed by Engineer-in-charge. Note ;- Laminated sheet shall be measured and paid in point wiring item of BOQ. |
| 166 | Supply and fixing switch piano flush type (ISI marked), 5/6Amps, single pole, two way fixed on laminated sheet complete all as specified and as directed by Engineer-in-charge. (laminated sheet and covering frame shall be includedin point wiring item of BOQ). |
| 167 | Supply and fixing switch piano flush type (ISI marked), Bell Push, 5Amps, single pole, one way fixed on laminated sheet complete all as specified and as directed by Engineer-in-charge.(Laminated sheet shall be measured and paid in point wiring item of BOQ). |
| 168 | Supply and fixing Socket outlet multipurpose type (ISI marked), 2 in 1, 5 pin, 5/6 Amp, flush type fixed on laminated sheet complete all as specified and as directed by Engineer-in-charge. (Laminated sheet shall be measured and paid in point wiring item of BOQ). |
| 169 | Supply and fixing Socket outlet multipurpose type (ISI marked), 2 in 1, 6/5 pin, 6 amp and 16 amp, flush type fixed on laminated sheet complete all as specified and as directed by Engineer-in-charge. (Laminated sheet shall be measured and paid in point wiring item of BOQ). |
| 170 | Supply and fixing switch piano flush type (ISI marked), 15/16Amps, single pole, one way complete all as specified and as directed by Engineer-in-charge.(Laminated sheet shall be measured and paid in point wiring item of BOQ). |
| 171 | Supply and fixing ceiling rose (ISI marked) surface type polycarbonate isolated body three terminal, topline series 65x50mm, 6 Amp, complete all as specified and as directed by Engineer-in-Charge. |
| 172 | Supply and fixing angle lamp holder (ISI marked) polycarbonate cased body (B22 base), top line series, with back plate, 6Amps, complete all as specified and directed by Engineer-in-Charge. |
| 173 | Supply and fixingelectric calling Bell Ding Dong type, AC 230 Volts single pole including making elctric connection and testing, complete all as specified and as directed by Engr-in-charge. |
| 174 | Supply and fixing MCB ‘B’ curve suitable for 240 volts AC supply, 06 to 32 Amps, SP with over load and short circuit protection and rupturing capacity not less than 10 KA,fixing in DB/panel complete all as specified and as directed by Engineer-in-charge |
| 175 | Supply and fixing MCB ‘B’ curve suitable for 240 volts AC supply, 32-40 Amps, SPN with over load and short circuit protection and rupturing capacity not less than 10 KA,fixing in DB/panel complete all as specified and as directed by Engineer-in-charge |
| 176 | Supply and fixing in replacement (concealed flush to wall) factory made DB (made out of CRCA sheet not less than 1.2mm thick, fitted with DIN channel neutral link and 200 Amp rated bus bar) SPN, 12 Way 240V, suitable for mounting MCB/Isolator, conforming to IS-13032, DB shall be semi glosy finished with epoxy polyster based powder paint sprayed and backed at high temperature between powder paint process to ensure smooth finish and protection against corrosion atmosphere. The DB shall be double door type with hinged door with locking arrangement, the DBs shall be same make as MCBs, DB shall be provided with level marking indicating the incoming and outgoing circuits on always as specified. The DBs shall be of IP-43 protection class, including taking down unserviceable old DB any type including MCB etc and including making good disturbed surfaces of walls as necessaty complete all as specified and directed by Engineer-in-charge. Note :- MCB’s shall be measured and paid separately under appropriate item of BOQ. |
| 177 | Supply and fixing in replacement of LED complete fitting including batten, T-8 Retro LED polycarbonate 1 x 20Watt, appx 4 feet long, with decorative ultra ceiling square profile linear LED lighting fixture with extruded polycarbonate environment friendly, including electric connection with using 2 core flexible copper conductor cable 23/0.00076 from ceiling rose to tube fitting, complete fitting with all accessories and following specifications, including taking down old unserviceable light fitting any type complete all as specified and directed by Engineer-in-Charge :- (a) Lumen system efficacy of luminaire should be minimum 100 Lumen per watt.(b) Input Voltage range : 140 to 270 volts.(c) Temp operating range : Minus 10°C to Plus 45°C(d) Power factor : Minimum 0.95 (e) THD : Max10%.(f) IP rating : IP-20.(g) CRCA pre coated housing with two coloured plastic end cap.(h) LED Driver of the same make as of the luminaire.(j) LED driver should be complete with all protections vizopen/short circuit protection, over voltage protection, all as per standard design of manufacturer.(k) Surge protection minimum 2.5 kV. (l) CCT : Minimum 6000K(m) CRI : Minimum 80 (n) Rated life time : 50000 burning hrs (Average 10 to 12 hrs daily) |
| 178 | Supply and fixingin replacement LED light fitting 1 x 10Watt, appx 2 feet long with decorative ultra ceiling square profile linear LED lighting fixture with extruded polycarbonate environment friendly, including electric connection with using 2 core flexible copper conductor cable 23/0.00076 from ceiling rose to light fitting,complete fitting with all accessories and following specifications, including taking down old unserviceable light fitting any type complete all as specified and directed by Engineer-in-Charge :- (a) Lumen system efficacy of luminaire should be minimum 100 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 10°C to Plus 45°C(d) Power factor : Minimum 0.95(e) THD : Max 10%. (f) IP rating : IP-20. (g) CRCA pre coated housing with two coloured plastic end cap.(h) LED Driver of the same make as of the luminaire. (j) LED driver should be complete with all protections vizopen/short circuit protection, over voltage protection, all as per standard design of manufacturer. (k) Surge protection minimum 2.5 kV.(l) CCT : Minimum 6000K(m) CRI : Minimum 80(n) Rated life time : 50000 burning hrs (Average 10 to 12 hrs daily) |
| 179 | Supply and fixing in replacement of LED Bulkhead fitting 1 x 10Watt, complete with Standard profile linear LED lighting fixture with extruded polycarbonate environment friendly, including electric connection with using 2 core flexible copper conductor cable 23/0.00076 from ceiling rose to light fitting, complete fitting with all accessories and following specifications, including taking down old unserviceable light fitting any type complete all as specified and directed by Engineer-in-Charge :- (a) Lumen system efficacy of luminaire should be minimum 100 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 10°C to Plus 50°C(d) Power factor : Minimum 0.95 (e) THD : Max 10%. (f) IP rating : IP-65. (g) CCT : 6500K (h) Impact resistant polycarbonate housing, polycarbonate diffuser with silicon gasket (j) LED Driver of the same make as of the luminaire. (k) LED driver should be complete with all protections vizopen/short circuit protection, over voltage protection, all as per standard design of manufacturer.(l) Surge protection minimum 2.5 kV.(m) CRI : Minimum 80 (n) Rated life time : 50000 burning hrs (Average 10 to 12 hrs daily) |
| 180 | Supply and fixing in replacement LED lamp minimum 3 star rated 9/10 W LED B-22 base complete all as specified and directed by Engr-in-Charge with following specifications (a) Lumen system efficacy of lamp should be minimum 100 Lumen per watt. (b) Input Voltage range : 160 to 270 volts (c) Temp operating range : Minus 10°C to Plus 50°C (d) Power factor : Minimum 0.90 (e) CRI: Minimum80 |
| 181 | Supply and fixing in replacement energy efficient LED security light fitting of 25W pressure die cast aluminium housing/body, heat resistant clear toughened glass,better optics for uniform distribution street luminaire, with driver, including electric connection, fixing the light fitting with existing bracket and clamps but including repalcement of nut bolts if required, complete fitting with all accessories and following specifications, including taking down old unserviceable light fitting with old bracket any type complete all as specified and directed by Engineer-in-Charge :- (a) Lumen system efficacy of luminaire should be minimum 100 Lumen per watt.(b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 10°C to Plus 50°C (d) Power factor : Minimum 0.95(e) THD : Max10%.(f) IP rating : IP66. (g) IK rating:Minimum IK07 (h) Built in potted LED Driver of the make as of the luminaire.(j) LED driver should be complete with all protections vizopen/short circuit protection, over voltage protection, all as per standard design of manufacturer.(k) Surge protection 10 kV (inbuilt + extended) (l) CCT : 5700 K. (m) CRI: Minimum 70 (n) Lens - High Efficiency wide angle lens. (o) BIS Approved fixtures and driver (p) Rated life time : 50000 burning hrs (Average 10 to 12 hrs daily) |
| 182 | Supply and hanging /fixing ceiling fan 1200 mm sweep AC Supply (Input Voltage Range ; 120 to280V), BLDC type, 5 star rated, BEE and ISI Marked super enamelled, copper winding of "B" class insulation, single phase, minimum 30W (± 10%), Temperature rise 40 degree maximum without remote but with and including capacitive regulator, 03 No blades, down rod including accessories, white colour, total harmonic less than 10%, 5 speed, hanging in position including making connection with flexible cord three core twisted copper conductor of suitable sizefrom ceiling rose to fan complete all as specified. Note :- (i) Serial Number as issued by Engr-In-Charge of celing fan and GE Office name shall also be written on fan with red colour permanent marker and fixing of regulator on switch board, cost for the same shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account |
| 183 | Supply and fixing exhaust fan (heavy duty) steel body, AC single Phase 230V, 50 Cycle per second, size 300mm sweep with blades and frame including self closing GI louvers off mode protection against birds etc mounted in suitable opening arrangement. including electric connection with and including new flexible sheathed copper wire of size 24/0.2mm, 3 core from ceiling rose to fan (not exceeding 0.5 mtr long), and hanging on wall with 4 Nos steel fastners 10mm dia 100mm long and making good the disturbed surface complete all as specified and as directed by Engineer-in-charge. Note :- Serial Number of exhaust fan issued by Engr-In-Charge and GE Office name shall also be written on fan with red colour permanent marker. |
| 184 | Supply and fixing ventilating Air fresher Fan of size 250mm sweep, single phase, 1200RPM, copper winding, made of sturdy Engineering plastic complete with louvers shutter, including provision of cutting of wall for suitable opening as per fan and making good the disturbed surface as per existing, including electric connection with suitable flexible copper cable from ceiling rose to fan complete all as specified and as directed by Engineer-in-charge. |
| 185 | Material and labour for concealed sub main wiring (Two run for main i.e. phase and netural and one run for continues as earth wire connected to earth dolly etc., using red, black and green colour wires as colour coding) with 6 Sqmm single core, FRLSH PVC insulated multistrand copper conductor drawn through and including PVC conduit 25mm dia (medium quality ISI marked), on independent circuit from DB including all fitting arrangement i.e. PVC clamp, rawl plug, screw, terminal/junction box, tee, bend etc. and including cutting of chases in wall, taking out old sub main wiring of any conductor any sizefrom conduit and taking down old unserviceable conduit with fittings, and making good disturbed surfaces of walls as per original complete all as specified and as directed by Engineer-in-charge. Note :-Three run of 6 sqmm copper wire and one run conduit shall be measured as one RM length for payment. |
| 186 | Supply, installation, commissioning and testing of factory made LT panel Board (main control board) of minimum size 100cm x 80cm x 25cm fixed on/inside wall (front side open-able, double glass door including locking arrangements and handle), dust proof, vermin proof made out of CRCA sheet 2 mm thick powder coated, Suitable arrangement for fixing electronic energy meter-04 Nos, including pre wired internal wiring with & including single core, PVC copper conductor unsheathed wire multistanded 6 sqmm including provision of rubber beading and mild steel cable glands and lugs,provision of air fins for ventilation, including comprising of 01 No MCCB 100Amps-FP-16KA-415V for incoming, 04 Nos MCB 40Amps-SPN for outgoing, 01 No MCB 10 Amps-SPN for outgoing and copper bus bar 200Amps for 3 phase and netural complete including all connections incoming / out going, including taking down old panel board any type with fittings complete all as directed by Engineer-in-charge. Note :- Cost for fixing of old Electronic meter after taking out from old panel board shall deemed to be included. |
| 187 | Supply and fixing electric water heater (Geyser) storage type ABS body of capacity 25 Ltrs, 5 Star rating, 230V, single phase AC supply,inner tank made out of heavy duty stainless steel sheet (designed with single weld line, factory tested with Hydraulic pressure as per latest IS code) with glass lined coating complete with all accessories such as safety valve, thermostate, NRV, connection piece, PVC connection for hot and cold water, three core PVC Insulated PVC Sheathed copper conductor flexible cable including 15Amp plug suitable for existing socket, including 04 No Nut bolts etc for hanging of geyser. Nut bolt grouting in wall in PCC (1:2:4) using 12.5mm graded stone aggregate for hanging the geyser and making good the disturbed surface complete all as specified and as directed by Engineer-in-charge. |
| 188 | Material and labour for Earthing complete with galvanised iron earth plate electrode of size 600 x 600 x 6 mm buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including GIearthing wire 4 mm dia by means of GI bolts/nuts/washers and protected by 15 mm bore GI medium grade pipe upto test point or upto main switch board, fixing with 02 Nos nuts and bolts. Earth plate shall be surrounded by alternate packed layer 15 cm thick of charcoal or coke and common saltall around bottom and top. 20 mmbore GI medium grade pipe for watering and including funnel, wire mesh, PCC chamber pit made with PCC (1:3:6) type C1 (using 20 mm graded stone aggregate) including necessary form work, excavation and earth work in any type ofsoil, returning filling and disposal of surplus soil to a distance not exceeding 50m,Pit cover 40mm thick made with RCC (1:2:4) type B1 (using 20 mm graded stone aggregate) including TMT reinforcement 8mm dia @ 75mm c/c both way, MS handle 12mm dia, cover rest on MS angle iron frame 40x40x6mm embeded in concrete duly painted with two coats of synthetic enamel paint over a coat ofred oxide primer, complete all as specified & shown in electrical plate No. 3 ofSSR 2009 (Part-I) including taking out/dismantling old unserviceable earthing system complete all as specified and as directed by Engineer-in-charge. Note:- (i) PCC chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner. (ii) Protection pipe and GI earthing wire upto test point or upto electric equipment from top of earth plate shall be included in the unit rate of this item. (iii) The earth testing arrangement should be done by the contractor as per direction of Engineer-in-charge. |
| 189 | Supply and laying or fixing or laid in trenches / ducts / through pipes / in floors / under roads / under hard standing /along poles and testing, Cross linked Polyethylene (XLPE) LT Cable, XLPE Insulated, PVC inner sheathed, bedded, galvanised steel strip or wire armoured cable (heavy duty) 1100 volt gradewith stranded aluminium conductor having cross sectional area 35 Sqmm3.5 core conforming to IS-7098 (Part-I)-1988 with upto date amendments, including taking out old unserviceable cable any size complete allas specified and as directed. Note :- (i) Excavation, earth work, sand cushioning, brick protection, boring/cutting of road and pipe shall be measured & paid separately under appropriate item of this Schedule.) |
| 190 | Material and labour for sand cushioning, with dry and clean fine river sand (for under ground cable) 8 cm before laying cable and 15 cm after laying and punned to 18 cm after laying of cablecomplete all as specified and as directed. (Note:- Punned thickness shall be considered for payment purpose) |
| 191 | Supply and laying un-reinforced precast concrete cable cover, class LV, type 2 flat, size 300mm x 180mm x 40mm for cable protection cover, laid dry in trenches over the cable , perpendicular to the direction of cable complete allas specified and as directed. |
| 192 | Supply and fixing in replacement GI tubing light grade of size 50 mm bore, ISI marked, fixed along poles/walls or laid in trenches, under road for cable protection including fittings (elbow, tee, socket etc) complete all as specified and as directed. (Note:- Excavation and earthwork as required shall be measured and paid separately under respective item of Sch.) |
| 193 | Material and labour for cutting of road/floor etc any type upto 45cm width and depth for laying of cable/pipe, after laying of cable/pipe returning filling with soil including spreading, leveling watering and well ramming in layers upto 30cm and top layer 15cm thick filling by using PCC (1:3:6) type C2 using 40mm graded stone aggregate to match the existing level of road/floor complete all as specified and as directed. |
| 194 | Boring of holes under road, pavement, hardstanding by using trenchless boring machine or by manual manpower suitable for inserting GI pipe any dia upto 50mm including removal of surplus soil and making good disturbed surface complete all as specified and as directed. NOTE:- Pipe for inserting as required shall be measured and paid for separately. |
| 195 | Material and labour for extra wiring for inverter socket out going to DB with 1.5 Sqmm single core, FRLSH PVC (using colour coding as directed) insulated multistrand copper conductor drawn through existing conduit (conduit for point wiring already catered in point wiring item of BOQ) including making connection to DB and inverter socket) complete all as specified and as directed by Engineer-in-charge. |
| 196 | Supply and fixing plug top 5/6Amp 3 pin good quality suitable for 240 volts, AC supply for inverter socket complete all as specified and as directed by Engineer-in-charge. |
| 197 | Supply and fixing socket outlet flush type (ISI marked), 25Amps (for inverter point),fixed on laminated sheet complete all as specified and as directed by Engineer-in-charge. (Laminated sheet shall be measured and paid in point wiring item of BOQ). |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
