|
| 1 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 2 | a)1:2:4 (1 cement : 2 coarse sand(zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 3 | b)1:5:10 (1 cement : 5 coarse sand(zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 4 | Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete : |
| 5 | a)100X58X1.90 mm |
| 6 | Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineer-in-charge |
| 7 | a)Extruded section profile size 48x40 mm |
| 8 | Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC ‘C’ channel of size 30mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. |
| 9 | Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. |
| 10 | An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the ‘C’ Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer’s specification & drawing. |
| 11 | 30 mm thick plain PVC door shutters. |
| 12 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, |
| 13 | (i)Single socketed pipes. |
| 14 | a)75 mm diameter |
| 15 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion. |
| 16 | a)Single tee with door |
| 17 | i)75x75x75 mm |
| 18 | b)Single tee without door |
| 19 | i)75x75x75 mm |
| 20 | c)Bend 87.5° |
| 21 | i)75 mm bend |
| 22 | d)Shoe (Plain) |
| 23 | i)75 mm Shoe |
| 24 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hardwood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. |
| 25 | a)75 mm |
| 26 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : |
| 27 | a)Water thinnable cement primer. |
| 28 | Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. |
| 29 | a)One coat |
| 30 | b)Two coats |
| 31 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 32 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : |
| 33 | a)One or more coats on old work. |
| 34 | Finishing walls with Acrylic Smooth exterior paint of required shade : |
| 35 | a)Old work (One or more coat applied @ 0.90 ltr/10 sqm). |
| 36 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground , all complete as per directions of Engineer-In-Charge. |
| 37 | a)With cement mortar 1:4 (1 cement : 4 fine sand). |
| 38 | Providing and fixing white vitreous china water closet squatting pan (Indian type) : |
| 39 | a)Orissa pattern W.C. pan of size 580x440 mm |
| 40 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. |
| 41 | a)10 litre capacity - White |
| 42 | Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete : |
| 43 | a)White solid plastic seat with lid |
| 44 | Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : |
| 45 | a)Flat back wash basin of size 550x400 mm. |
| 46 | Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 47 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: |
| 48 | a)100x100 mm size P type |
| 49 | i)With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 50 | Providing & fixing fly proof wire gauze mesh to windows, clerestory windows & doorsandto balcony grills with T.W. beading 15x1mm, nails & screws or with binding with GI wires as per site requirement and as directed by E-I-C etc complete. |
| 51 | a)Stainless steel (grade 304) wire gauze of 0.3 mm dia wire and 1.8mm aperture on both sides. |
| 52 | Providing and supplying of one coat of NITO Bond SBR modified cement slurry 1:2:5 (1 Litre:NITo Bond SBR :2 Litre water :5 Kg Cement ) of M/s Fosroc chemicals (India) Pvt Ltd or equivalent complete as per manufactureres specifications and as per the directions of Engineer-In-Charge. The rate shall include the cost of all materials ,hire charges for tools and plants, labour operations involved etc complete |
| 53 | Supply and application of rust remover, cleaning and etching agent Reebaklens RR of Ms Fosroc chemicals (India) Pvt Ltdover the corroded reinforcement bars, stirrups, lateral ties of slabs, beams & columns after removing rust scales, |
| 54 | Supply mixing and application of ready to use anticorrosive coating Nitozinc Primer of M/s Fosroc chemicals (India) Pvt. Ltd., or equivalent in two coats @ 28ml per R.M. (Proportion of 668ml Nitozinc base + 400 mlNitozinc primer hardener = 1 ltr) to the exposed steel reinforcements, stirrups, lateral ties of slabs, beams & columns complete as per the manufacturer\"s specification and as per the instructions of Engineer in charge, the rate is inclusive ofthe cost of all materials, hire charges of tools, labour charges etc., |
| 55 | Providing andfixing powder coated aluminium fly proof wire gauze meshdoors & window shutters with frames including fixing Stainless steel (grade 304) wire gauze/mesh of 0.20 mm dia wire and 1.8mm aperture on both sides. with necessary hinges ,handles and magnetic catchers etc all complete |
| 56 | a)For door -doorframe and door shutter frame made up of Alumimium profie of 50mm wide 1.20mm thick of Jindal Make or equivalent. |
| 57 | b)For window -window frame andshutter made up of Alumimium profie of 25wide 1.20mm thick of Jindal Make or equivalent. |
| 58 | Cleaning of existing T- V or T-VI or special T-V staff quarter at all heightsby removal of cob web, pigeon droppings, debris, unwanted, un serviceableabandoned material etcfrom all the rooms, dusting of walls,windows, doors ,cubboards etc, washing the flooring of all rooms with detergent,washing the flooring and dado of toilets and bath room with the acid etc.,making them into useable/liveable conditions complete etc for immediate occupation of quarteras directed by Engineer-in-charge.Each quarter cleaning is measured as one job. |
| 59 | T-V Qtr |
