Supply, Installation, Testing And Commissioning Of Electro-Mechanical Equipments At Water Supply Scheme Syed Abad Seer Under Jjm.---- 1 WSS Syedabad Seer(Adv. Cost Rs. 32,78,000/-) 2 Supply, Installation, Testing & Commissioning of Submersible Pumping Unitas per IS 8034 with following specification are as under :Discharge:5000 GPH Head: 103 MtrsPUMP : Efficiency = Not less than 50% Speed= 2900 RpmType of pump = Mixed flow.Type of fluid to be handled=Clear WaterMATERIAL OF CONSTRUCTION:Impeller= Stainless SteelPump Shaft = Stainless Steel SS 410.Pump Casing = Cast Iron/Stainless steelIMPELLER:Rest specification as clause- 1 of SBD Motor capacity = 15 HP 3 Providing/supplying and fitting ofG.I flanged Rising Main at site. The Pipe shall be hot dip Galvanized, class-C confirming to IS 1239. The job includes providing and fitting of M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16). Rest Specifications as per Clause-8 of SBDSize : DN80Class: C (Heavy) 4 Earth work in excavation by manual means in trenches for foundation, drains, pipes, cables (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and reaming of bottom lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed. (All kinds of soil 01 meter from cutting edge) 5 Filling available excavated earth in trenches, plinth, sides of foundation etc.in layers not exceeding 20 cm in depth, consolidating each deposited layer by reaming and watering, lead upto 50 m and lift upto 1.5m. 6 Providing and laying of stone soling including manual compaction 7 Centering and shuttering including strutting , propping etc. and removal of form work for Foundation , footings , bases for columns 8 Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering . all work upto plinth level with 1: 2 : 4 mix ( 1 cement , 2 coarse sand , 4 graded stone aggregate 20mm nominal size) 9 Fabrication, providing and fitting of split type MS clamps10 mm thick, 2 ft long and 3 inch wide for lowering and holding of pumping unit fitted. The job includes the cost of required size of nuts and bolts. Size: 80mm 10 Fabrication ,Providing and fitting of90-120 degree bend/elbowto be fabricated out ofG.I pipe, 1 m lengthand flanged on both ends ato make it leak proof. The flanges shall be M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16) and welded on both sides. The job includes nuts, bolts, gaskets etc as per site requirement.Size:DN 80Class: C 11 Cutting of hot dip galvanized G.I,pipe across the section by dint of pipe cutter/ gas cutter. The job also includes Providing and welding of M.S flanges to the two ends of pipe. The Thickness of flange shall conform to IS 6392 Part 1st Table-17. The flange welding shall be carried out in double layers using Advani/Esab/L&T- SS Bond make electrodes to form strong welding joint by dint of DC arc welding. The job further includes Providing and Fitting of nuts and bolts (conforming to IS:1363 Part 1st) and Rubber Insertion Gaskets (conforming to IS: 638/79) to be used between flanged joints. The size of the pipe isDN 80 , Class-C 12 Fabrication, providing and fitting of washout Tee with arm length 1.2 feet each. The Tee shall be fabricated out of G.I pipe with M.S Flanges conforming to BIS 6392/1997 Table 17 (Rating PN16) fastened with weld joints on three ends. Size: 80mmClass: C class 13 Providing and fitting of, Ductile Iron double flanged, non-rising spindle soft seatedglandless gate/ sluice valves as per IS14846 for regulating the water supply outside the pumping units .Rest Specifications as per clause - 12 of SBDSize: DN80PN:1.6/16 14 Providing and fitting ofDuctile Iron double flanged, Slanted seatswing check valve( NRV) as per IS 5312. The body shall be of ductile cast iron with fully encapsulated vulcanized EPDM rubber(Approved for drinking water). The valve shall be compatible for buried applications and shall be safe to install in both horizontal and vertical positions.Rest Specifications as per clause - 13 of SBDSize: 80mmPN: 1.6/16 15 Providing, fitting , testing and commissioning of50mm diameter ARV (Air Release valve ) as per IS 14845 to be fitted toG.Irising Main. The ARV Shall have the following specifications: i. Valve type -single chamber, single orifice.Rest Specifications as per clause - 14 of SBD size = DN 50 , PN 1.6/16 16 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses, construction of lineretc. including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer , including welding and bolted with special shaped washers etc. completeElectric resistance or induction butt welded tubes 17 Providing and fitting ofM.S 4 inch hinges -6 no and M.S handle heavy -8no., Anchor bolts with nuts (M16) of 0.3 m long= 04 No. Metallic strip (350mm×50mm×3mm) = 02 No. 18 Fabrication of gantry mechanism/CGI Shed /angle iron sleeping bedby way of providing Structural steel in built up sections , trusses and framed work, including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer all complete welded 19 Creation of pope mounted , outdoor type Electric Sub Stationby way ofS/I/T/C of 11/0.433 KVA , 3 Phase Distribution Transformer with Bimetallic Terminal connectors Energy level -2 Aluminum woundSpecifications conforming to IS : 1180 (Part 1) 2014 with latest amendments Rest specification as per clause - 26 Of SBDRating: 63KVA HT Transformer, 3 phase (Level 2). 20 Providing and fittingG.I Channel /Angle/ Flat of sizes including clamps 21 Supply, Installation, Testing and commissioning of Polymeric Gang operated Air break switch, outdoor type, triple pole, suitable for vertical installation, single break provided with locking arrangement at both ON and OFF position consisting ofHT post double insulator, copper or copper alloy high pressure heavy contact assembly, rod with bearings , operating handle and 2 length of 32mm dia. GI pipe conforming to IS 1818 1961, 06 No. of insulators, rated voltage 11KV 200A complete as per IS specs. 22 Supply, Installation, Testing and commissioning of 11KVpolymer fuses SetHorn Gap3-phase 200 Asuitable for vertical installation . 23 Supply, Installation, Testing and commissioning ofGapless Surgearrestor station class, 10KA, 9KV, LA With polymer housing , Station Type . 24 Supply and fitting of 11 KV polymeric composite pin insulator 12 KV, 5KN, Lighting impulse 75KV Positive, and 80 KV Negative , creepagedistance 320 mm 25 Supply, installation, errection of9 mtrs long H.T pole of specifications ST- 410 (sp-33) . The job further includes drilling of holes for installation of various accessories .wherever required. The job further includes GI wire earthing of pole as per REC standard. 26 P/F of Galvanized nuts, bolts of various sizes as per site requirement. 27 P/F Danger Plate with clamps 28 Providing and fixing G.I Barbed wire for anti climbing 29 Providing and fixing of anti climbing devices with clamps 30 Painting of poles Red oxide 31 Painting of poles Aluminum paint 32 Providing and fitting of ACSR as per IS 398 (part-2) 1996 for 50 sq.mmACSR (Galvanised steel reinforced) for fitment of various accessories 33 Supply, Installation and Testing of 35 Sq mm XLPE Aluminum H.Tcable (ABC type ) of 11 KV grade with following specs.Size (cross sectional area in sq mm) = 3×35 with reinforced wirePhases:Red, Yellow, Blue 34 Providing and fitting of Anchoring clampscomprising clamp body , plastic wedge, steel bill bracket , straps and buckles or nuts and bolts required for holding of 3 – Core , 35 Sq. mm H.T AB Cable. 35 P/F of 11 KV cable termination kit for connecting 35 Sq mm XLPE cable (ABC type) with the existing HT line near tapping point andHT transformer. 36 Providing and fitting of LT Distribution box for HT transformer with MCCB For incomer and SFU for out going circuits . Capacity of transformer: 63KVA 37 Fabrication, Providing and fitting ofModularmotor control panel of appropriate size fabricated out of 14 SWG sheet having required openings/vents and protection Class : IP-55 & fitted with accessories as under:a) Busbar Chamber:Rest specifications as per clause- 43- D of SBD 38 Providing, fitting, testing and commissioning ofvoltage stabilizeras per specifications below: Type of voltage controller: Manually operated copper wound, 3-phase, AC power supply multi step.Type of Regulator: Double plate type with electrolytic copper contacts.Input voltage : 250-400 volts.(3 phase)Output voltage : 400 ±10% volts.Frequency : 50±3 C/S.Rest Specifications as per Cluase-44 Of SBDRating::50KVA 39 Providing and fitting of 3-Core flatsubmersible copper cable conforming to IS: 694 (Part 1st) – 1964 & IS: 694 (Part 2nd) - 1964 for Submersible Pumping Unit and other electrical Equipments . The cable connections terminal shall be fitted with copper thimbles of required size. Size: 10 sqmm 40 Providing and Fitting of 3 /3.5/2-Core, XLPE Armoured Aluminium Cable conforming to IS: 7089 part 1st as service line from the HT transformer to control panel including necessary thimbling, crimping, taping etc.NOTE:- The cable terminal ends for connection to switchgear at various requisite points shall be Al. Thimbles of dowel’s make and of appropriate size and connected by hydraulic crimp tool only.i) 50 sqmm, 3.5core, LT, 1.1 KV 41 ii) 10sqmm, 2 core, LT , 1.1 KV 42 P/I of earthing station for substation, LT panel, DG set and stabilizer comprising of company fabricated earthing electrode as per IS: 3043. The job includes Auguring of bore of required dia/depth for installation of electrode along with backfill compound mixed with soil and all other items required thereof for achieving the best result. The job includes connecting of electric gadgets through GI strip as per relevant standards.Safe earthing electrode size:80 mm dia , Length :2000 mmBack fill compound :30 kg 43 Illumination of Premises:Providing and erection of 9 Mtr long Hot Dip Galvanized octagonal pole (single Section) with bottom 150mm, top 75mm wide, thickness 3mm with 70 Microns Zinc coating having inside arrangement for providing of power connection along with following items.Rest Specifications as per clause -50 of SBD 44 Providing, installation, testing and commissioning of area lighting 120 Watt LED (Street Light Type) on top of octagonal pole vide item No.36Having following specs:Input: 90-240 V 50 HzPower Factor: >0.9Rest Specifications as per clause -51 of SBD 45 Providing, Installation and testing of 2KVA fully automatic voltage stabilizer with input voltage 70-240 V and output 220 V. The stabilizer shall be installed and connected to the electric circuit as per location provided by site incharge. 46 Providing, laying & fixing with adhesive/bonding material of insulation rubber mats on the floor of the pump house, covering area around electro-mechanical machinery for safeguarding the life & limb of the workmen due to possible leakage of current & short circuit. The floor surface shall be made good & shall be free from dust, grease, foreign material & moisture free. The mats shall be as per IS 15652:2006 & shall have the following specifications: -Composition: Rubber (synthetic mats for electrical purpose)Thickness: - 2.5mm Size: - 1M wide.The rubber mats shall be accepted with manufacturers test certificate. 47 Providing and fitting of 19 mm thick multilayered ply sheet of size 6 x 3 feet , 2 nos including cutting , fixingall complete including painting of the play sheet by one coat of primer and two coats of enamel paint 48 Providing of good quality bedding for night stay/Shift consisting of: -i) Mattress with warm cover size 6x3 (6Kg)- 02 No’sii) Quilt with warm cover size 5x8 (6Kg)- 02 No’sRest specifications as per clause -57 of SBD 49 Carriage of sand , stone aggregate by mechanical transportincluding loading, unloadingand stacking (average distance-5km) 50 Carriage of soling stone by mechanical transportincluding loading, unloadingand stacking (average distance-5km) 51 Carriage of cement/steel/CGI sheet/GI pipes below 100mm dia and other heavy materials by mechanicaltransportincluding loading, unloadingand stacking (average distance -25Km)
