Irrigation Department has published Tender For Construction Of Nepali / Gorkha Cultural Cum Multipurpose Centre At Asomiya Nepali Sanskriti Sangrakshan Nyaas, Panikhati, Guwahati.. Submission Date for this Tender is 09-01-2023. Electrical Maintenance Tenders in Kamrup Assam. Bidders can get complete Tender details and download the document.
| Sr No | CorrigendumDate | Corrignedum | CorrigendumType | NewSubmissionDate |
| 1 | 05-Jan-2023 | Modification of EMD validity | Financial Bid | 09-01-2023 |
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in- charge.:All kinds of soil. |
| 2 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil:: Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia |
| 3 | Close timbering in trenches including strutting, shoring and packing cavities (wherever required) complete. (Measurements to be taken of the face area timbered).: Depth exceeding 3 m but not exceeding 4.5 m |
| 4 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 5 | PLINTH FILLING: Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 6 | Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil |
| 7 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. |
| 8 | Raising low site including around the building with approved soil obtained from outside by truck carriage within initial lead of 8.00 km including breaking clods, dressing etc. complete including paying necessary land compensation, municipal gate fees, if any monopoly duty etc. (profile measurement to be taken and 12.5% deduction for shrinkage to be made from total quantity) etc. complete as directed and specified, including forest royalty within a distance of 8.00 km. (forest royalty shall be reimbursed on production of necessary certificate from the forest authority duly countersigned by D.F.O. concerned). |
| 9 | ANTI-TERMITE TREATMENT:Supplying chemical emulsion in sealed containers including delivery as specified. :Chlorpyriphos/ Lindane emulsifiable concentrate of 20% |
| 10 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti- termite treatment (excluding the cost of chemical emulsion) : : Along external wall where the apron (existing) is not provided using chemical emulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300mm including excavation channel along the wall & rodding etc. complete::: With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration |
| 11 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti- termite treatment (excluding the cost of chemical emulsion) ::: Treatment of soil under existing floors using chemical emul sion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor:::With Chlorpyriphos/Lindane E.C. 20% with 1% concentration |
| 12 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti- termite treatment (excluding the cost of chemical emulsion) : ::Treatment of existing masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to the full depth of the hole : :With Chlorpyriphos/Lindane E.C. 20% with 1% concentration |
| 13 | BRICK SOLING: Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks. |
| 14 | CEMENT CONCRETE WORKS:: 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 15 | DPC: Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) |
| 16 | Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil. |
| 17 | PLINTH PROTECTION:Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation leveling and dressing and finishing the top smooth. |
| 18 | PLINTH PROTECTION DRAIN: Providing drain with cement concrete (1:3:6) 10cm thick sides 10cm thick bed over brick flat soling including 15mm thick cement plastering in prop. 1:3 finished with a floating coat of cement slurry as directed with necessary shttering for sides and earth work in excavation of foundation trenches and refilling the sides after completion of work etc. as specified.: i) 300mm wide and average 250mm deep with bed slope 1 in 150 with initial depth of 100mm. |
| 19 | Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. |
| 20 | Providing and placing in position 100 mm thick factory made machine batched & machine mixed Precast RCC Rectangular Covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm dia TMT bars of Fe 500 grade @ maximum 100mm c/c on both ways , neat cement punning on finished surface, properly encased on all edges with 1.6 mm thick , 100 mm wide MS sheet duly painted over priming coat , reinforcement to be welded at edges with MS sheet and providing 2 Nos. 12 mm dia bar for hooks etc i/c cost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge. |
| 21 | DESIGN MIX CONCRETE:Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.:: All works upto plinth level : Concrete of M25 grade with minimum cement content of 300 kg /cum |
| 22 | DESIGN MIX CONCRETE:Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.All works above plinth level upto floor V level: Concrete of M25 grade with minimum cement content of 330 kg /cum |
| 23 | FORMWORK: Centering and shuttering including strutting, propping etc. and removal of form for : :Foundations, footings, bases of columns, etc. for mass concrete |
| 24 | FORMWORK:Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 25 | FORMWORK: Centering and shuttering including strutting, propping etc. and removal of form for : : Suspended floors, roofs, landings, balconies and access platform |
| 26 | FORMWORK: Centering and shuttering including strutting, propping etc. and removal of form for :Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 27 | FORMWORK : Centering and shuttering including strutting, propping etc. and removal of form for :Columns, Pillars, Piers, Abutments, Posts and Struts |
| 28 | FORMWORK: Centering and shuttering including strutting, propping etc. and removal of form for : Stairs (excluding landings) except spiral-staircases |
| 29 | FORMWORK: Centering and shuttering including strutting, propping etc. and removal of form forEdges of slabs and breaks in floors and walls:: Under 20 cm wide |
| 30 | FORMWORK: Centering and shuttering including strutting, propping etc. and removal of form for : Weather shade, Chajjas, corbels etc., including edges |
| 31 | FORMWORK Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured). 5.11.1 Suspended floors, roofs, landing, beams and balconies (Plan area to be measured) |
| 32 | STEEL REINFORCEMENT: Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.::Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 33 | STEEL REINFORCEMENT : Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. : Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 34 | STEEL REINFORCEMENT:Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. : :Mild steel and Medium Tensile steel bars |
| 35 | MASONRY WORK: Brick work with common burnt clay F.P.S. (non-modular) bricks of class designation 7.5 in foundation and plinth in::: Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 36 | MASONRY WORK : Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. : Cement mortar 1:3 (1 cement :3 coarse sand) |
| 37 | Autoclaved Aerated concrete (AAC) Block : Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately). |
| 38 | AAC SUPER STRUCTURE: Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand ). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work. |
| 39 | ROOFING SHEET: Providing & fixing at all heights, levels and locations colour finish Aluminium alloy roofing sheets of alloy IS designation 31500, temperHx8 conforming to IS 737 and dimensions as per IS code 2676 with characteristics of good formability and corrosion resistance. The profile sheets shall be fixed to truss members in slope or required pitch or curvature with Hex cap headed self drilling/tapping Stainless steel screws M6, 50 mm long with 3 mm EPDM seal washer etc. all inclusive of labour, scaffolding, T&P and sundries etc. complete as per directions of the Engineer-In-Charge. (Cost of truss/frame work shall be paid separately).::0.56 mm, Aluminium Color coated troughed profile with center to center pitch of 200 mm, depth of 32 mm, overall profile width1092 mm, cover width 1000mm. |
| 40 | RIDGE: Providing and fixing of Pre-coated colour or mill finish Aluminium Roofing Accessories in 0.71 mm thickness ,Alloy 31500 (ISdesignation)[Aluminium Alloy (AA) 3004 (ISO designation)] For color, coating shall be 5-7 microns epoxy primer on both sides ofthe sheet and polyester top coat 15-18 microns, using self drilling/ tapping SS screws of size 6 x 50mm with 3mm thick EPDM sealand SS plain washer complete .Precoated/mill finish aluminium Ridges plain(500- 600mm) |
| 41 | TRUSS : Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 42 | STAINLESS STEEL RAILING : Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc. |
| 43 | UPVC WINDOW : Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.::Two track two panels sliding window made of (small series) frame 52 x 44 mm &sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm) |
| 44 | UPVC WINDOW : Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.:: Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension . (Area of window above 1.75 sqm upto 2.50 sqm). |
| 45 | UPVC WINDOW : Providing and fixing factory made uPVC white colour sliding glazed window above 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads, uPVC extruded interlocks and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle on one side of extreme panel along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) touch lock with hook (if required for wire mesh panel), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes,wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.:: Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 2.50 sqm upto 4.00 sqm.) |
| 46 | UPVC WINDOW : Providing and fixing factory made uPVC white colour sliding glazed window above 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads, uPVC extruded interlocks and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle on one side of extreme panel along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) touch lock with hook (if required for wire mesh panel), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes,wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.:::Two track four panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 4.00 sqm upto 8.00 sqm). |
| 47 | UPVC WINDOW ( FIXED) :Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.:Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.) |
| 48 | UPVC WINDOW:Providing and fixing factory made uPVC white colour sliding glazed door comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware"s and drainage of water etc. After fixing frame the gap between frame andadjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. 9.147F.1 Two track two panels sliding door made of (big series) frame 67 x 50 mm & sash 46 x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door above 2.00 sqm upto 5.00 sqm) |
| 49 | Float glass panes:4 mm thick glass pane (weight not less than10kg/sqm). |
| 50 | Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured). |
| 51 | M.S. GRILL: Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings /wooden frames with rawl plugs screws etc. |
| 52 | Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.Upto 5mm depth and 5 mm width |
| 53 | WPC DOOR FRAME: Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately).Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.26.86.7 Frame size 65 x 150 mm |
| 54 | WPC FLUSH DOOR SHUTTER: Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full bodythreaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 30 mm thick |
| 55 | FLUSH DOOR SHUTTERDECORATIVE TYPE : Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 56 | Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete : 9.70.1 125x64x1.90 mm |
| 57 | Providing and fixing expandable fasteners of specified size with necessary plastic sleeves and galvanised M.S. screws including drilling holes in masonry work /CC/ R.C.C. and making good etc. complete.50 mm long |
| 58 | SLIDING DOOR BOLT: Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 250x16 mm |
| 59 | TOWER BOLT: Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : SIZE: 250x10 mm |
| 60 | HANDLE:Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : SIZE: 125 mm |
| 61 | DOOR STOPPER: Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Single rubber stopper |
| 62 | LOCK:Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles ofapproved quality with necessary screws etc. complete. |
| 63 | HANDLE:Providing and fixing bright finished brass handles with screws etc. complete: SIZE: 125 mm |
| 64 | DOOR CLOSER: Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. |
| 65 | VISION PANEL: Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors. (cost of glass excluded) (overall area of door shutter to be measured):: Rectangular or square |
| 66 | Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 2nd class teak wood :; 50 x 20 mm |
| 67 | WALL TILES:Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.Deduct for not using 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) bedding in laying of floor tiles and jointing with grey cement slurry @ 3.3 kg/ sqm.. |
| 68 | FLOOR TILES: Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600x600 mm |
| 69 | ANTI-SKID TILES: Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. :Glazed Vitrified tiles Antiskid finish of size : Size of Tile 600 x 600 mm |
| 70 | CEMENT CONCRETE FLOOR: Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 11.3.1 40 mm thick with 20 mm nominal size stone aggregate |
| 71 | GRANITE FLOORING: Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. : Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent |
| 72 | MARBLEFLOORING : Providing and laying machine cut, mirror polished, Italian Marble stone flooring laid in required pattern in linear portion of the building all complete as per architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.: 18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc. |
| 73 | Providing edge moulding to 18 mm thick marble stone counters, Vanitiesetc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.Marble work |
| 74 | WOODEN FLOORING : 25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with ::Second class teak wood |
| 75 | FALSE CEILING : Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed fromM.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flangesof 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channelwith connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mmthick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer"s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) |
| 76 | CEMENT PLASTERING : 12 mm cement plaster of mix :1:4 (1 cement: 4 fine sand) |
| 77 | CEMENT PLASTERING : 15 mm cement plaster on the rough side of single or half brick wall of mix :: 1:4 (1 cement: 4 fine sand) |
| 78 | Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers. |
| 79 | Extra for plastering exterior walls of height more than 10 m fromground level for every additional height of 3 m or part thereof. |
| 80 | EXTERNAL PAINTING : Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm)over and including priming coat of exterior primer applied @ 2.20kg/10 sqm |
| 81 | PRIMER ON STEEL AND OTHER METAL SURFACE: Applying priming coat:With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works. Applying primary coat over new steel |
| 82 | PAINTING ON STEEL AND OTHER METAL SURFACE : Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture sqm: Two or more coats on new work |
| 83 | INTERNAL PAINTING (PLASTIC PAINT) : Wall painting with acrylic emulsion paint of approved brand andmanufacture to give an even shade : Two or more coats on new work |
| 84 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface: Water thinnable cement primer |
| 85 | PUTTY : Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. : 1.5 mm thk |
| 86 | Grading roof for water proofing treatment with: Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) |
| 87 | WATER PROOFING AND ROOF TREATMENT: Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge decketc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.:For vertical surface two coats @ 0.70 kg per sqm |
| 88 | WATER PROOFING AND ROOF TREATMENT:Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retainingwalls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge decketc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. :; For horizontal surface one coat @1.10 kg per sqm. |
| 89 | PILE :Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). Note: Truck Mounted rotary/TMR/Tubewell boring machine shall not be used .::500 mm dia piles |
| 90 | VERTICAL LOAD TEST: Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. Note: 1. Initial and Routine Load Test shall not be carried out by Dynamic method of testing. Note: 2. Testing agency shall submit the design of loading platform for the approval of Engineer-in-charge. :Single pile upto 50 tonne Safe capacity:Initial test (Test Load 2.5 times the Safe capacity) |
| 91 | ROUTINE TEST:(Test Load 1.5 times the Safe capacity) |
| 92 | INTEGRITY TEST: Integrity testing of Pile using Low Strain/ Sonic Integrity Test/ Sonic Echo Test method in accordance with IS 14893 including surface preparation of pile top by removing soil, mud, dust & chipping lean concrete lumps etc. and use of computerised equipment and high skill trained personal for conducting the test & submission of results, all complete as per direction of Engineer-in-charge. Note :- The inclusion of the above item in the schedule of work shall be judiciously decided by the technical sanctioning authority, keeping in view the quality control, type of soil strata & importance of the project.: 600 mm dia piles |
| 93 | Filling sunken floor with broken jhama brick bats and sand including compacting and supplying of materials complete as specified and directed for all levels. |
| 94 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : 12.21.1 In 75x75 mm deep chase |
| 95 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 96 | RWP:Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.:75 mm diameter |
| 97 | RWP : Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.: 110 mm diameter |
| 98 | PAINTING PIPE:Painting (two or more coats) on rain water, soil waste and vent pipes and fittings with synthetic enamel paint of approved brand and manufacture and required colour over a priming coat of approved steel primer on new work. :100 mm diameter pipes |
| 99 | PAINTING PIPE : Painting (two or more coats) on rain water, soil waste and vent pipes and fittings with synthetic enamel paint of approved brand andmanufacture and required colour over a priming coat of approved steel primer on new work.:150 mm diameter pipes |
| 100 | Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete. |
| 101 | Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. |
| 102 | Providing and fixing mild steel round holding down bolts with nuts and washer plates complete. |
| 103 | Providing and fixing bolts including nuts and washers complete. |
| 104 | ROOF INSULATION Providing & fixing " AEROLAM" or equivalent 19mm cross linled closed cell polyethylene foam insulationsheet having nominal Density 30 ± kg/cum, Thermal Conductivity: 0.0382 w/m°k, DIN 52615, Fire characteristics as per BS 476 part 7, self extinguishing, non toxic sheets including necessary arrangement and stationeries for fitting fixing and complete in all respect as specified and directed. |
| 105 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. |
| 106 | Empty boring for specified diameter piles from ground level to cut-off level.Pile Dia 500 mm |
| 107 | TURBO VENTILATOR: Supplying, fitting and fixing in position turbo ventilator of Nylon made Typhonic Bearing, double top cap ensured permanent alignment in inverted cap design, corrugated foil framed of aluminium fabrication for wind driven having wind velocity 1600 exauster of effective throatal Dia 21 inch and overall dia 28 inch having overall height 17 inch as specified and directed by the Engineer-in-charge. |
| 108 | EARTH FILLING Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. |
| 109 | SANITARY INSTALLATION INDIAN TYPE WATER CLOSET: Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 110 | EUROPEAN TYPE WATER CLOSET: Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid |
| 111 | URINAL: Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Single half stall urinal with 5 litre P.V.C. automatic flushing cistern |
| 112 | DIVISION PLATE: Supplying fiting and fixing vitreous china division plate including fitting and fixing compete as directed and specified. (i) Parryware Make , (a) White, (i) Partion Magnum / Large (Cat. No.C0571/07) |
| 113 | WASH BASIN: Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: : White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps |
| 114 | KITCHEN SINK:Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 17.10.1 Kitchen sink with drain board:size 510x1040 mm bowl depth 250 mm |
| 115 | BOTTLE TRAP: Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. |
| 116 | MIRROR: Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 117 | MIRROR: Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backingRectangular shape 453x357 mm |
| 118 | GLASS SHELF: Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl ,plugs etc., complete. |
| 119 | TOILET PAPER HOLDER: Providing and fixing toilet paper holder :C.P. brass |
| 120 | WASTE COUPLING: Providing, fitting and fixing Chrome Plated waste coupling complete as directed and specified. a) Jaquar Make (i) 32mm (HT/FT) (Cat.No.ALD-705 / 709) |
| 121 | SOAP TRAY: Providing, fitting and fixing S.S soap tray / soap dish complete as directed and specified. (i) Jaquar Make, (a) Continental (Cat.No.ACN-1331N) |
| 122 | TOWEL RAIL: 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. |
| 123 | TOWEL RAIL: Providing, fitting and fixing CP towel rail complete as directed and specified. (a) Jaquar make (ii)Continental 600mm (Cat.No. ACN-1111N) |
| 124 | COWEL: Providing fitting and fixing PVC cowel of ISI make complete as directed and specified(ii) 110mm dia. PVC cowel of ISI make |
| 125 | GRATING: C.P. Grating(ii) 110mm dia |
| 126 | BIB COCK: Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. : 15 mm nominal bore |
| 127 | STOP COCK: Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. :15 mm nominal bore |
| 128 | VALVE:Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : : 25 mm nominal bore |
| 129 | VALVE:Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : : 32 mm nominal bore. |
| 130 | VALVE:Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :50 mm nominal bore |
| 131 | VALVE:Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end)80 mm nominal bore |
| 132 | VALVE: Providing and fixing 25 mm nominal bore ball valve (brass) of approved quality, High or low pressure, with 150mm dia of pragya or equivalent plastic floats complete : |
| 133 | C.P.V.C. PIPES : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. INTERNAL WORK: Concealed work, including cutting chases and making good the walls etc: 20mm nominal outer dia Pipes |
| 134 | C.P.V.C. PIPES : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. INTERNAL WORK: Concealed work, including cutting chases and making good the walls etc. : 25mm nominal outer dia Pipes |
| 135 | C.P.V.C. PIPES : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. : 32 mm nominal outer dia Pipes |
| 136 | C.P.V.C. PIPES : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.External work:25 mm nominal dia Pipes |
| 137 | C.P.V.C. PIPES : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.External work:32 mm nominal dia Pipes |
| 138 | C.P.V.C. PIPES : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.External work: 40 mm nominal dia Pipes |
| 139 | C.P.V.C. PIPES : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.External work: 50 mm nominal dia Pipes |
| 140 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 141 | PVC PIPES,BENDS,JUNCTIONS,TEES ETC. Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 or other ISIapproved including joining ,fitting and fixing with clamps etc.as necessary completeat all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia. |
| 142 | Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 or other ISIapproved including joining ,fitting and fixing with clamps etc.as necessary completeat all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (iv) 75mm dia. |
| 143 | Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 or other ISIapproved including joining ,fitting and fixing with clamps etc.as necessary completeat all levels including below G.L as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages. (ii) 110mm dia. |
| 144 | Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 or other ISIapproved including joining ,fitting and fixing with clamps etc.as necessary completeat all levels including below G.L as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages. (iv) 75mm dia. |
| 145 | Supplying, fitting and fixing 87.5 degree PVC bend of or other ISIapproved including joining ,fitting and fixingetc.as necessary completeat all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia. |
| 146 | Supplying, fitting and fixing 87.5 degree PVC bend of or other ISIapproved including joining ,fitting and fixingetc.as necessary completeat all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (iv) 75 mm dia. |
| 147 | Supplying, fitting and fixing 87.5 degree PVC bend of or other ISIapproved including joining ,fitting and fixingetc.as necessary completeat all levels including below G.L as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages. (ii) 110mm dia. |
| 148 | Supplying, fitting and fixing 87.5 degree PVC bend of or other ISIapproved including joining ,fitting and fixingetc.as necessary completeat all levels including below G.L as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages. (iv) 75 mm dia. |
| 149 | Supplying fitting and fixing 87.5 degree PVC bendwith door of or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia. |
| 150 | Supplying fitting and fixing 87.5 degree PVC bendwith doorof or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (iv) 75 mm dia. |
| 151 | Supplying fitting and fixing 87.5 degree PVC bendwith door of or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages. (ii) 110mm dia. |
| 152 | Supplying fitting and fixing 87.5 degree PVC bendwith doorof or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages. (iv) 75 mm dia. |
| 153 | Supplying fitting and fixing45 degree PVC bend of or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia. |
| 154 | Supplying fitting and fixing45 degree PVC bend of or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (iv) 75 mm dia. |
| 155 | Supplying fitting and fixing45 degree PVC bend of or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages. (ii) 110mm dia. |
| 156 | Supplying fitting and fixing PVC Plain single tee of or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia. |
| 157 | Supplying fitting and fixing PVC Plain single tee of or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages. (ii) 110mm dia. |
| 158 | Supplying fitting and fixing PVC Plain single tee of or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages. (iv) 75 mm dia. |
| 159 | Supplying fitting and fixing PVCsingle tee with door of or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia. |
| 160 | Supplying fitting and fixing PVCsingle tee with door of or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (iv) 75 mm dia. |
| 161 | Supplying fitting and fixing PVCsingle tee with door of or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages. (ii) 110mm dia. |
| 162 | Supplying fitting and fixing PVCsingle tee with door of or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages. (iv) 75 mm dia. |
| 163 | Supplying fitting and fixing PVCsingle ‘Y’ of or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia. |
| 164 | Supplying fitting and fixing PVCsingle ‘Y’ of or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (iv) 75 mm dia. |
| 165 | Supplying fitting and fixing PVCsingle ‘Y’ of or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages. (ii) 110mm dia. |
| 166 | Supplying fitting and fixing PVCsingle ‘Y’ of or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages. (iv) 75 mm dia. |
| 167 | Supplying fitting and fixing PVCsingle ‘Y’ with door of or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 110mm dia. |
| 168 | Supplying fitting and fixing PVCsingle ‘Y’ with door of or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 75 mm dia. |
| 169 | Supplying fitting and fixing PVCsingle ‘Y’ with door of or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages. (i) 110mm dia. |
| 170 | Supplying fitting and fixing PVCsingle ‘Y’ with door of or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages. (ii) 75 mm dia. |
| 171 | Supplying fitting and fixing PVC double‘Y’ plain of or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 75 mm dia. |
| 172 | Supplying fitting and fixing PVC double‘Y’ plain of or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages. (i) 110mm dia. |
| 173 | Supplying fitting and fixing PVC double‘Y’ plain of or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages. (ii) 75 mm dia. |
| 174 | Supplying fiting and fixing PVC cross ‘T’ with doorof (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches.(i) 110mm x110mm |
| 175 | Supplying fiting and fixing PVC cross ‘T’ with doorof (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 75 mm x 75mm |
| 176 | Supplying fiting and fixing PVC cross ‘T’ with doorof (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages.(i) 110mm x110mm |
| 177 | Supplying fiting and fixing PVC cross ‘T’ with doorof (Supreme/Prince) or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages.(ii) 75 mm x 75mm |
| 178 | Supplying fitting and fixing PVC coupler of or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 110 mm dia |
| 179 | Supplying fitting and fixing PVC coupler of or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (iii) 75 mm dia |
| 180 | Supplying fitting and fixing PVC coupler of or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages. (i) 110 mm dia |
| 181 | Supplying fitting and fixing PVC coupler of or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.Cand making good to the damages. (iii) 75 mm dia |
| 182 | Supplying fitting and fixing PVC reducer of or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (iii) 110 mm x 90 mm |
| 183 | Supplying fitting and fixing PVC reducer of or other ISI approvedincluding joining , fittingand fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (iv) 110 mm x 75mm |
| 184 | Supplying fitting and fixing PVC socket plug of or other ISI approvedincluding joining , fittingand fixing etc. in exposed surface or trencesas necessary complete at all levels including below G.L. as directed and specified. (a) 110 mm |
| 185 | Supplying fitting and fixing PVC socket plug of or other ISI approvedincluding joining , fittingand fixing etc. in exposed surface or trencesas necessary complete at all levels including below G.L. as directed and specified. (b) 75 mm |
| 186 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : : 100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 187 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design:150 mm dia. R.C.C. pipe |
| 188 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design::250 mm dia. R.C.C. pipe |
| 189 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size), inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 190 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. 19.32.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 191 | ESTIMATE OF DEEP TUBE WELL Labour for test boring with 40mm (internal) dia G.I. Pipes including keeping surplus of earth and every 2.00m after first 3.00m depth and delivering the same in nearest P.W.D. camp in the small tin container(container, scaffolding, tools etc. will have to be arranged by the contractor at his own cost). |
| 192 | Machine boring of deep tube well upto 200mm dia. Bore hole asdirected by the Engineer in Charge |
| 193 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.:150 mm nominal size dia |
| 194 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.: 200 mm nominal size dia |
| 195 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (SUCTION PIPE):50 mm nominal outer dia Pipes |
| 196 | Providing and placing in position filters of 40 mm diameter G.I./PVCpipe with brass strainer of approved quality. |
| 197 | Providing and fixing gun metal non- return valve of approved quality (screwed end) : 50 mm nominal outer dia Pipes: Horizontal |
| 198 | Providing and fixing gun metal non- return valve of approved quality (screwed end) : 50 mm nominal outer dia Pipes:: Vertical |
| 199 | Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. |
| 200 | Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. |
| 201 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:150 mm dia |
| 202 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:200 mm dia |
| 203 | Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.: 200 mm clamp |
| 204 | Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).:150 mm dia. |
| 205 | Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).:200 mm dia |
| 206 | ESTIMATE FOR LIFT Supplying installation, testing and commissioning of Passenger Elevator(KONEmakefor 3stop(680 kg, 10 persons) having contract speed of 1.0 Metre/Sec (approx.)mps serving different floorin the existing lift shaft as per detailed specification enclosed and as under Location of the lift- 1.Type & Capacity-Passenger-10 Persons & 680Kg.2.Speed- 1.0 Metre./Sec (approx.) 3. Serving : Ground Floor to 2ndFloor ( 0,1,2) 3 Stops 3 Levels 3 Openings 4. Available Travel-6.90 metres 5. Pit depth: 1400 mm 4. LocationHead room - Top 13. Head Room : 4170 mm. 7. Shaft dimension WxD- 1950 mm Wide X 1900 mm 9. Machineroom less 11.Car dimention WxDxH : 1200mm x1400mm x 2239mm. 11. Clear car height : 2200 mm 14. Car Door size:W x H : 900 mm x 2000 mm 11. Car door type : Door centre opening, 2 panels 11. Shaft wall : Rcc 8. Power supply : 415 Volts50 Hz 10. Light power supply: 230 V |
| 207 | ELECTRIFICATION WORKS Point wiring : Point wiring in PVC conduit, with modular type switch - Wiring for light point / fan point / exhaust fan point / call bell point ( for door call bellonly )with 1.5 Sq.mm FRLS PVC insulsted copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 Sq.mm FRLS PVC insulated copper conductor single core cable etc as required. Conduit Make : Anchor / Richa or equivalent as approved. Wires : FR/FRLS - Finolex, RRKable, Anchor, Havels or equivalent asapproved. : Group B |
| 208 | POWER POINT AND SUB MAIN WIRINGWiring for light/power plug with 2x2.5 Sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit alongwith 1 No. 2.5 Sq.mm FRLS PVC insulated copper conductor single core cable for loop earthing as directed forLP power point ( having 2 nos. 5A switch and 2 nos. 5A socketandLP points ) |
| 209 | Wiring for15/16A power plugwith 2x4 Sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit alongwith 1 No. 4 Sq.mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 210 | Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required .Make : Anchor / Richa or equivalent as approved:4 Module (125mmX75mm) for Geyser and powerPoint |
| 211 | Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required .Make : Anchor / Richa or equivalent as approved :6 Module (200mmX75mm) forLP2 - TV / COMPUTER POWER POINT(5A2nos Switch with 5A2 nos. Socket ) |
| 212 | Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required .Make : Anchor / Richa or equivalent as approved :3 Module (125mmX75mm) for LP1-lightpowerPoint in rooms andCommon place |
| 213 | Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required .Make : Anchor / Richa or equivalent as approved :1 Module (75mmX75mm) for call bell switch |
| 214 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including conections but excluding modular plate etc. as required. Make ; Havells/ Panasonic/ Schneider or equivalent as approved.: 2 Nos. 5/6amp modular switch for LP2 - TV/ Computer Point.And LP1 and existing switch boards |
| 215 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including conections but excluding modular plate etc. as required. Make ; Havells/ Panasonic/ Schneider or equivalent as approved.:2 nos. 5/6 amps modular socket forLP2- TV Point. And LP1 and existing switch boards |
| 216 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including conections but excluding modular plate etc. as required. Make ; Havells/ Panasonic/ Schneider or equivalent as approved.: 15/16 amps modular switch for Geyser andPP and for common lighting switch |
| 217 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including conections but excluding modular plate etc. as required. Make ; Havells/ Panasonic/ Schneider or equivalent as approved.: 15/16 amps modular socketfor Geyser and PP |
| 218 | Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.FOR DOOR CALL |
| 219 | Supplying and fixing call bell switch for service call in the existingSB , complete as required. |
| 220 | Circuit / submain /Light plug wiringin PVC conduit: Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed PVC conduit as required. Wires : FR/FRLS - Finolex, RRKable, Anchor, Havels or equivalent asapproved:2 x 1.5 Sq.mm + 1 x1.5 Sq.mm earth wire from 15A commmonswitch lighting points of corridor and stage lightingas directed. |
| 221 | Circuit / submain /Light plug wiringin PVC conduit: Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed PVC conduit as required. Wires : FR/FRLS - Finolex, RRKable, Anchor, Havels or equivalent asapproved : 2 x 2.5 Sq.mm + 1 x 2.5 Sq.mm earth wire from DB to SB and common switch lighting / fan systemas directed |
| 222 | Circuit / submain /Light plug wiringin PVC conduit: Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed PVC conduit as required. Wires : FR/FRLS - Finolex, RRKable, Anchor, Havels or equivalent asapproved :2 x 4 Sq.mm + 1 x 4 Sq.mm earth wire forsub main fromDB to PP / AC / Geyser |
| 223 | Circuit / submain /Light plug wiringin PVC conduit: Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed PVC conduit as required. Wires : FR/FRLS - Finolex, RRKable, Anchor, Havels or equivalent asapproved: :2 x 6 Sq.mm + 1 x 6 Sq.mm earth wire forsub main fromTPN to SPN DB |
| 224 | Circuit / submain /Light plug wiringin PVC conduit: Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed PVC conduit as required. Wires : FR/FRLS - Finolex, RRKable, Anchor, Havels or equivalent asapproved : :2 x 6 Sq.mm + 1 x 6 Sq.mm earth wire forsub main fromMDB to TPN DB |
| 225 | POWER DISBRIBUTION BORD Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutralbus bar, earth bar, din bar, interconnections, powder paintedincluding earthing etc. as required. (But withoutMCB/RCCB/Isolator) as required.- for each floor power distribution for hostel and guest house rooms.:4 way (4 + 12), Double door |
| 226 | Supplying and fixing following way, single pole and neutral ways surface/ recess mounting,MCB distribution board, 240 V, on surface/ recess complete with tinned copper bus bar, neutral bus bar, earth bar, dinbar,interconnections,powderpaintedincluding earthing etc. as required. (But without MCB/RCCB/Isolator) as required. -: 8 wayDouble door for rooms |
| 227 | Supplying and fixing following way, single pole and neutral ways surface/ recess mounting,MCB distribution board, 240 V, on surface/ recess complete with tinned copper bus bar, neutral bus bar, earth bar, dinbar,interconnections,powderpaintedincluding earthing etc. as required. (But without MCB/RCCB/Isolator) as required. - : 12wayDouble door |
| 228 | Supplying and fixing following way, single pole and neutral ways surface/ recess mounting,MCB distribution board, 240 V, on surface/ recess complete with tinned copper bus bar, neutral bus bar, earth bar, dinbar,interconnections,powderpaintedincluding earthing etc. as required. (But without MCB/RCCB/Isolator) as required. - : 16 wayDouble |
| 229 | Supplying and fixing 5 amps to 32 amps rating, 240 / 420volts, "B" series, miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. : 10 ampsto 32A Single pole |
| 230 | Supplying and fixing 5 amps to 32 amps rating, 240 / 420volts, "B" series, miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. :32 amps DP |
| 231 | Supplying and fixing 5 amps to 32 amps rating, 240 / 420volts, "B" series, miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required : 32A Triple pole for TPN DB incomming |
| 232 | Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. |
| 233 | Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enamelled white on both sides, and with inscription in single red colour on front side as required for each electrical room door . |
| 234 | Supply & Installation ofFans Installation, testing and commissioning of ceiling fan including wiring the down rods of standard length (upto 30 cm) with 1.5 sq.mm FR PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. |
| 235 | Supply and Installation of 3 blade1400 mm sweep white Summer Breeze ceilingfan. Make ; Oirentor equivalent Havells orCGL make as approved. |
| 236 | Supply and Installation of 3 blade1200 mm sweep white Summer Breezeceilingfan. Make ; Oirentor equivalent Havells orCGL make as approved. |
| 237 | Supply and Installation of 3 blade 1200 sweep very silent very powerful double bearing ceiling fan. Make ; Oirent Aeroquiet or equivalent Havells or CGL make as approved. For guest house room and common room. |
| 238 | Supplying and fixing stepped type elctronic fan regulator on the existing modular plateswitch box excluding modular plate as required. |
| 239 | Supply and Installation of 450 mm dia Tornado wall fan.Make ; Oirentor equivalent Havells, CGLor Panasomic make as approved. |
| 240 | Supply and Installation of IndustrialHVLS FAN having 5/6 nos extrudedaluminium black anodixed blades, 10/11 feet (3.3M)sweep diameter ,. Producing a 2-3 mph breezeequivalent to a 4-7 degree reduction in preceived temperature completewith all necessary accessories as required for installation of the fan in complete. , Make Serco, ecoair or equivalent as approved |
| 241 | Installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connections, testing, commissioning etc. as required. |
| 242 | Supply of 300 mm high sppedexhaust fan . Make ; Oirent air flow or equivalent Havells, CGLor Panasomic make as approved. For Toilets |
| 243 | Supply of 450 mm industrial heavy dutyhigh spped (1400 rpm) exhaust fan . Make ; Oirentor equivalent Havells, CGLor Panasomic make as approved. For Toilets |
| 244 | Supply of 150mm high sppedexhaust fan having automatinc lovour shutter . Make ; Oirent Ventilator HSor equivalent Havells, CGLor Panasomic make as approved. For VIP waiting room Toilets |
| 245 | Supply & Installation of Light /Luminaries and FixturesInstallation, testing and commissioning of prewired, flourescent fittings / all type of LED indoor ceiling fittings , complete with all accessories and tube etc. directly on ceiling/wall/ False ceiling, including connections with 1.5 sq.mm. PVC insulated, copper conductor, single core cable etc. as required. |
| 246 | Supplying of following LED lighting fixtures complete with Drive andLamps with reflector/cover etc. complete as required:- Make : Sura ,Siska /CGL/ Havells orPanasonic as approved24W NW (6K) LED Recessed mounted square slim and elegant down light panel made of aluminium PDC housing for indoor applicationn with high aesthetic appeal for uniform light of 6000K Make ; Surya Rivo LED or equivalent CGL, Havells, or Siska as approved.for Stageinside lighting. |
| 247 | Down light square shapedsurfacemounted 12 watt,NW (6.5K) LEDlight fitting. Make - CGL Pearl Nios LCDSPLN-S-12NW 12W CDLor equivalent Surya, Siska, Havells, panasonic as approvedfor corridor and staircase lighting. |
| 248 | Down light square shapedrecess mounted12 watt LED ,NW (6.5K)light fitting. Make - CGL Pearl Ultima LSCSM-12NWCDLor equivalent Surya, Siska, Havells, panasonic as approvedfor corridor and staircase lighting. For VIP waiting room |
| 249 | Supply of 70W LED CDL lamp set made of highly efficacy wellglass consuming lesser energy with hight lighting levels having an efficacy of 110Lm / W ingressprotectionofIP65. Make : CGL LWV12-70-CDL orequivalent Havells. Surya, Philips, Siskaas approved |
| 250 | Down light square shapedsurfacemounted 6 watt,WW(3.0K) LEDlight fitting. Make - CGL Pearl Nios LCDSPLN-S-6WW or equivalent Surya, Siska, Havells, panasonic as approvedfor corridor and staircase lighting. For Night lamp |
| 251 | 1 x 20 W LED6500K retrofitting polycarbinateT8tube with in built driver and heat sink double sided connection with compact commercial batten suitable for T8 LED tube Make ;CGL Cat Ref. LT820865 andfor batten unilite DMLN1LT8-16 or equivalentSiska orHavells , phillips, bajaj as approved.for small classroom lighting |
| 252 | Supplying andfixingbrassbatten/angleholderincluding connection etc. as required. |
| 253 | Supply and installation of 12W LED NW bulb on existing angle holder as required. Make ; Siska, Surya, Havellsas approved. |
| 254 | Supply and installation of 40W NW (6K) LED street light along with 600 mm long 32mm diaGI arms with necessary clamps , nuts and bolts as required to install the lamp set on culm or stress members as directed .Make ; Siska - SSK -ST-40W SN or equivalent Havells, CGL , Surya, or philips as approved for building peripherallighting. |
| 255 | Geysers: Supply and installation of25Lts capacity Geyserwith necessary piping etc. as required to complete the job. Make : CGL Arno Neoor equivalent Smith /Bajaj. |
| 256 | Geysers : Supply and installation of15 Lts capacity Geyserwith necessary piping etc. as required to complete the job. Make : CGL Arno Neoor equivalent Smith /Bajaj. For AC & NON AC ROOMS |
| 257 | Air conditioner: Supplyand installation of wall mountedInverter type5-Star rated Air Conditioner havingsplit unit with indoor BLDC fan motor, R32 prefilled regrigerant gas, selfmanufactured Dual Inverter compressor, Ocean Black Fin, Ocean Black Protection Low gas detection , 100% copper condenser, 100% Grooved copper, Stabilizer free , HD filter, cools at 52 degree C |
| 258 | Supply of 19mm CPVC condansate drain pipe with 9mm thick class - O nitral rubber insulation asrequired for above AC system |
| 259 | Supply of 4 core 1.5 sqmm copper control cum transmission unarmoured power cablein a suitable conduit as required between indoor and out door uint |
| 260 | Supply and installation of modular32A AC starter switch on exixting 2modulebox.Make ; HavellsACYSMXW321 or equivalent |
| 261 | Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required .Make : Anchor / Richa or equivalent as approved : 2 Module (75mmX75mm) for AC starter |
| 262 | Fire Extenguisher : Supply andistallation of 4.5 Kg, Mild steel ABC, A class powder/ CO2 type fire extenguisher |
| 263 | Earthing : Earthing withG.I.earthpipe4.5metrelong,40mmdia cover plate having locking arangement and watereing pipe with charcoal / coke and salt as required for panel earthing and transformer body earthing. |
| 264 | Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required. |
| 265 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. |
| 266 | Providing and fixing earth bus bar joint made of 20mmx3mm thick 125 mm long with 6 nos. G.I bolts , nuts, chuck nut and spring washers etc. complete as requried |
| 267 | UNDER GROUND CABLE WORKS FOR POWER SUPPLY : Supply of following sizes of 1.1 KV grade single core/multicore aluminium conductor XLPE insulated and PVC sheathed armoured / unarmouredcable conforming to IS 1554 (Part-I) 1988.. Make ; RR Kable, Havells, Polycab, KEIOr equivalent as approved:4 Core, 95 sq.mm. Aluminiun conductorXLPEARMOUREDCable. From Transformer to MDB |
| 268 | Supply of following sizes of 1.1 KV grade single core/multicore aluminium conductor XLPE insulated and PVC sheathed armoured / unarmouredcable conforming to IS 1554 (Part-I) 1988.. Make ; RR Kable, Havells, Polycab, KEIOr equivalent as approved: 3 Core, 4 sq.mm. Aluminiun conductorXLPEARMOUREDCable.for out door lighting |
| 269 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioC70:C80ning, protective covering and refilling the trench etc as required. : Up to35 sq. mm |
| 270 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioC70:C80ning, protective covering and refilling the trench etc as required. : Up to95 sq. mm |
| 271 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. : Up to35 sq. mm |
| 272 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.:Upto 95sq. mm |
| 273 | Supply and making cable end termination with brass compression glands and crimped aluminium lugs following sizes of PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade of the following sizes as required.: 4C X95 sq. mm (19mm) |
| 274 | GI PIPES: Supplying and embedding following G.I pipe of medium class for cable entry / road crossing of cable etc. including bending the pipe as required shape as required. b) 40 mm dia |
| 275 | STREET LIGHT : Supply of IP65, 72 W LED Street lightMake : Siska -SLF-CF-72W or equivalent Surya, Havells, Philipsas approved. |
| 276 | Supply and installation of IP55 Poly carbonate SMC box size 230mmx170mmx105mm door fixed hinged (make - syntex) with 5A SP MCB DIN bar, Earth bar ect. as reqiored with necessary anchor fastnerrequired to fit the box on the wall at required position or as directed . |
| 277 | Supply of 6 mtrs height GIoctagonal street light pole with base plate, arms , nuts & bolts as required for installation of the street light as mentioned above and as directed. |
| 278 | Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required.:Above 4.5 metre and upto 6.5 metre (for decorative stright lightpole ) as diected. |
| 279 | TRANSFORMER : Supplying, installation testing and commissioning of the following rating copper woundout door type transformer. Transformer should be as per CEA / BIS guidelines as ammended up to datefor losses along with LV enclosure.:100 KVA, 50Hz. 11/0.433 KV. Oil filledLEVEL 2, 4 STAR ,COPPER WINDING transformer . |
| 280 | Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.for transformer neutral grounding. |
| 281 | Supplying and layingdoublerun 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection terminating with nut,bolt, spring, washer etc. asrequired. |
| 282 | MAIN POWER DISTRIBUTION BOARD (MDB) Design, manufacture, supply, installation, testing and commissioning of cubicle type panel fabricated out of 14 SWG CRCA sheet steel , floor mounted totally enclosed switch baord suitable for use of 415 volts , 3 phase, 50HZ complete with aluminium bus-bar and all accessories including supply and fixing of following incoming and outgoing switchgears. The sheet steel shall undergo minimum 7 tank treatment followed by finishing powder coating of min 60 micron thickness.Incomer:FP 125 A 50 KA Ics= 100% Icu MCCB with microprocessor based release with buit in E/F Protection, extended rotary handle and spreader terminal - 1 Nos. Digital Ammeter0-200A 3 Phase 4 WireAccuracy Class 1 as per IEC 62053-21 Bezel dimension (W X H)=96 X 96mm:1 No. Digital Voltmeter - 0-500V 3 Phase 4 WireAccuracy Class 1 as per IEC 62053-21 Bezel dimension (W X H)=96 X 96mm :1 Nos. CT 200/5 240V 3 Phase 4 wire Freq 50Hz+/- 5% Accuracy Class 0.5S : 1 Set SP MCB with 10KA breaking capacity of rating 6 Amp :03 Nos RYB Indicating Lamps : 1 set,BUS BAR : 800 A TPN AL. bus bar with coloured heat shrinkable PVC sleeve-1 Set,Outgoings: 63A 3P MCCB, 25KA - 2Nos , 40A 3P MCCB, 25KA - 6Nos , 32 A TP MCB, 25 KA - 1 No.. B - series, 32 A DP MCB, 25 KA - 4 No.. B - series ,EARTH BUS. |
| 283 | D.G.SET : Supply, Installation and commissioning of 75KVA,430V, 3-Phase Silent Diesel Generator Sets with auto run and autochange over facility.Make ; Kirloskar, Cumminsor CGL as approved. |
| 284 | 2HP, Single phase 6/ 26stage submerssible pump . |
| 285 | Supply of motor control panel suitable for 2HP single phase submerssible pump set |
| 286 | Supply of 3 Core, Submerssible copper cable |
| 287 | Lightening Arrestors SystemEarthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.ForLightning Arrester Earthing |
| 288 | Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required. |
| 289 | Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required. |
| 290 | Providing and fixing ofG.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run) |
| 291 | Providing and fixing ofG.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run) |
| 292 | CONSTRUCTION OF 100 KVA 11/0.430 KV BJPCOMMUNITY HALL SUBSTATION, HAZONBORY, ALONG WITH CONSTRUCTION OF 500 METER OF SINGLE CIRCUIT 11kVOH LINE WITH ACSR "RACOON" CONDUCTOR ON STEEL TUBULAR POLE "SP-56 "(WITH AVERAGE SPAN OF 35 METERS) WITH FEEDER PILLARS SP 56 Length of pole = 11.00 metreslength, coated with black bituminous paint (internally & externally) up to the earth level , with 14 mm. diameter through hole for earth connection, including grouting with concrete (1:2:4) on steel base plate.( Length of sections of poles are Bottom = 5.20 M, Middle =3.40 M, Top = 2.40 M, Out side dia. & Thickness Bottom = 165.10 x 4.50 mm, Middle =138.70 x 4.50 mm, Top =114.3 x 3.65 mm |
| 293 | G.I. channel cross arm 100 x 50 x 6 x2200mm |
| 294 | G.I. angle 50 x 50 x 6 mm. for guard bracket |
| 295 | GI 11KV Cross Arm with angle size 50x50x6 mm |
| 296 | .I.Hook - GI |
| 297 | 11KV Disc Insulator ( Polimer ) 72 KN ( B&C Type ) |
| 298 | 11KV PIN insulator (Polimer ) 5KN (FRP 24mm ) |
| 299 | ACSR "Racoon" conductor |
| 300 | Tension clamp for ACSR "Racoon" conductor |
| 301 | Ploe Clamp ofGI Flat 50x6 mm |
| 302 | G. I. wire 8 swg. for guarding |
| 303 | Hot Dip G. I. wire 6 swg. for earthing (every pole to be earthed) |
| 304 | HT Stay Set |
| 305 | Hot Dip GI Wire Stay Wire 7/10SWG ( for HT) |
| 306 | 11KV Guy Insulator (Porcelain ) |
| 307 | G.I Earthing pipe50mm dia , 3m length, 3.15mm thickness with perforated holesofdia 15mm dia at 30cm length along length ofthe epipe Earthing as per latest amendments of Indian Electricity Rules 2003 |
| 308 | GI Strip 25x3 mm for DTR Earthing |
| 309 | PG clamp, for ACSR "Racoon" conductor |
| 310 | Danger plate "11000 volts" |
| 311 | Bimatalic Lug 300 sq mm |
| 312 | Bimatalic Lug 185 sq mm (for neutral ) |
| 313 | 11KV GOAB Switch 400 Amp |
| 314 | 11KV DO Fuse Set 150A Assembly |
| 315 | 11KV, 5KA Linghtning Arrestor line type |
| 316 | 3P4W ICS DLMS compliant HT Trivector energy meter |
| 317 | 3 Ph 4W Combined CT/PT Accuracy Class : 0.5,25/5A |
| 318 | Control Cable1 Core X 2.5 sq. mm |
| 319 | Metering Cabinate |
| 320 | 11KV Danger plate |
| 321 | AMR Modem |
| 322 | Sundries L/S |
| 323 | Load security to be deposited to APdCLfor 85 kW Commercial Load |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
