Tender For Widening And Strengthening Of Samani To Ranada Road Km 00/000 To Km 08/952 Of Taluka - Amod, District - Bharuch In The State Of Gujarat Under Pmgsy-Iii Scheme Batch 2
Tender Value
4.56 Crore
Estimated cost
Bid Submission
31 Dec 2022
0 days left
EMD
9.59 Lakhs
Bank guarantee accepted
Document Fee
6000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
bharuch → Gujarat
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Widening And Strengthening Of Samani To Ranada Road Km 00 / 000 To Km 08 / 952 Of Taluka - Amod, District - Bharuch In The State Of Gujarat Under Pmgsy-Iii Scheme Batch 2
BOQ
| Sl. No. | Item Description |
| 1 | Item Description |
| 2 | Scarifying the existing bituminous road surface to a depth of 50 mm and disposal of scarified material with a with all lead & lift as per Technical Specification |
| 3 | Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlierand disposal of unserviceable materials and stacking of serviceable material (By Mechanical Meas) |
| 4 | Excavation for roadwork in soil with hydraulic excavator of0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross-sections, and transporting to the embankment location with all lead & lift as per Technical Specification |
| 5 | Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement as per Technical Specification |
| 6 | Construction of embankment with approved material obtained from borrow pits with a all lead & lift, transporting to site, spreading, grading to required slope and compacting to meet requirement with with all lead & lift as per Technical Specification |
| 7 | Layingand spreding avilable soil in the subgrade on a prepared surface, pulversing, mixing the spread soil in place with rotavator with4 percent slaked lime having minimum 70 percent of content of CaO , grading with motor grader and compecting with Roller |
| 8 | Construction of embankment with Coir Fiber (Desinsity of Coir Fiber 1.4g/cc) , spread and compacted in as, with all lead and liftas per Technical Specification. (Min. thikness 6.5mm) |
| 9 | Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavatorat OMC, and compacting with smoothwheelroller to achieve thedesired density, complete as per Technical Specification . (GSB-II) (Including Hard Shoulder) |
| 10 | Providing,laying,spreadingand compactinggradedstone aggregateto wet mix macadam specificationincludingpremixingthematerialwith water at OMC in mechanicalmixer (Pug Mill), carriageof mixed materialby tipper to site, layingin uniform layers in sub-base/base course on a well prepared sub-base and compacting with smoothwheel roller of 80 to 100kN weighttoachievethedesireddensityincludinglighting,barricatingandmaintenance of diversion, etcand Technical Specification |
| 11 | PrimeCoatwithbitumenemulsion:-Providingandapplyingprimercoatwith bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.9-.1.2 kg/sqm using mechanical means |
| 12 | Providing, laying and rolling of 37.50mm compacted thick B.M. in one layer with B.T. aggregate as specified and using bitumen for tack coat at the rate of 2.50 Kg. / 10Sqm. and using bitumen (VG-30) for mixing with aggregate at the rate of 3.3% of total mix including heating and mixing in drum mix plant, and transporting and spreading the same by paver finisher and consolidation with vibratory roller 80 to 100 Kn static weight including necessary firewood, oil, lubricants, labour charges, using contractor\"s own drum mix plant, machineries and requirement, tool etc. completed in accordance with the requirement of specification. |
| 13 | Providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 13.2 mm to 0.09 mm (Type-B) aggregates using penetration grade bitumen (VG-30) @ 19 kg/10 Sqmt. to the required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a Smooth wheeled roller 8-10 tonne capacity, and finishing to required level and grade. |
| 14 | Construction ofun-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design,laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, |
| 15 | Printing new letter and figures of any shade with synthetic enamel paint black or any other approved colour to give an even shade as per drawings and Technical Specification English and Roman |
| 16 | Providing and erecting direction and place identification retro-\reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide , fixed over aluminium sheeting, 2 mm thickwith areaexceeding 0.9 sqm supported on angle Iron post with primer and two coats of epoxy paint as per Specification. |
| 17 | Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron pipe 600 mm x 500 mm rectangular(chevron sign) |
| 18 | Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron pipe 900 mm x 300 mm rectangular(Hazard sign) |
| 19 | Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron pipe 600 mm circular sign board(Speed limit) |
| 20 | Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron pipe 600 mm equilateraltriangle(Cautionary sign) |
| 21 | Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron pipe 750 mm side octagon(Mandatory sign) |
| 22 | Providing and fixing of a typical design of PMGSY Informatory Sign Board “The board will be a composite unit consisting of three plates of Aluminum Composite Materials (ACM), material specifications as per Clause 1701.3.7. The top most plate will be in diamond shape of 600mm x 600 mm size, riveted over welded M.S. angle iron frame of 25 mm x 25mm x 5 mm size on back on edges. The middle plate will be 1200 mm x 150 mm size riveted over welded M.S. angle iron frame of 25mm x 25mm x 5 mm size on back on edges. The main lower most plate will be 1500 mm x 600 mm size, riveted over welded M.S. angle iron frame of 25 mm x 25 mm x 5 mm size. Welding of all the sheets over angle iron frame will be done neatly to have plain surface on one side. The angle iron frames of the lower most plate and the middle plate will be welded to two nos. 75 mm x 75 mm (12 SWG) sheet tubes posts placed at 1125 mm apart Centre to Centre. The top of the middle plate will be flushed with the top of 75 mm dia. medium steel tube posts and these posts will be embedded in cement concrete M15 grade blocks of 450 mm x 450 mm x 600 mm below ground level. The height of bottom of the lower most plate will be 1200 mm from normal ground level and the bottom of middle plate will be 100 mm above the top level of the lower most plate. The diamond Shaped plate mounted over angle iron frame will be connected to middle plate by square medium steel section of 47 mm x 47 mm thickness 12 SWG having a spacing of 100 mm between the diamond shaped plate and middle plate and this square section will be welded to the bottom point of the diamond shaped plate. ii). the lettering and borders, etc. of middle and bottom plate, PMGSY logo on top plate shall be as per clause 1701.4.6 Messages/Borders. All the sections of frame and posts will be painted with primer and two coats of Epoxy paint. The steel tube below ground level will be painted with three coats of Epoxy paint. The design, painting and lettering shall be done as per approved drawing.” |
| 23 | Providing and fixing Logo Board of PMGSY size 600×600mm diamond shape with 1 plate of size 900×250 mm made of 16 gauge sheet over frame of angle iron 25×25×3mm as per PMGSY specifications & drawing, painted with ready mixed synthetic enamel paint of superior quality in required shade and colour.All sections of framed posts and steel will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 (PMGSY Logo Board) |
| 24 | Providing and fixing of typical PMGSY CITIZEN\"S INFORMATION BOARD with Logo as per MORD specifications and drawing, made of 75mm square or 75mm dia. circularsteel tube of 12 SWG 3.2 m hight and cross member 2 Nos. 1m long,fixed with Angle iron 50 x 50 x 5 mm MS angle on the back side 2Nos vertical and 4 Nos horizontal. It is mounted by 2 plates of 1.6mm thick and size 900 x 750 mm, the pipe shall be erracted on 600 x 600 x 750 mm foundation blocks at appropriate depth made of cement concrete 1:2:4, painted by standard color as per drawing with lettering, border, heading and logo etc. using sinthetic enamel paint of superior quality andall details as per standard drawing ofPMGSY including welding, excavation, concreting, painting of base, border and lettering, painting cross section of road and other required details etc complete as directed by engineer-in-charge for any type of board wheather for flexible pavement or concrete pavement as prescribed for PMGSY. .(One for Flexible, Rigid Pavement &maintenance) |
| 25 | Reinforced cement concrete M15grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification5th Kilometre Stone (precast) |
| 26 | Reinforced cement concrete M15grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical SpecificationOrdinary Kilometer Stone (Precast) |
| 27 | Reinforced cement concrete M15grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification200 m stone (precast) |
| 28 | Reinforced cement concrete M15 grade boundary pillars/local stone of standard design as per IRC:25, fixed in position including finishing and lettering but excluding painting as per drawing and Technical Specification |
| 29 | Providing and fixing guard stones on curves or at any other place as directed by engineer incharge made of 220 X220X1000 mm hammer dressed stones and fixed 400mm into the ground in morum and broken agreegates block of size 500X500X500mm and painted with white and black bands in 2 coat with redimix enamel paint including excavation of pit etc. complete. |
| 30 | Speed Braker (For 9.0 Mt Formation Width (5.50 carriage way width))Providing and laying rounded hump type of Speed Breaker confirming to IRC â?? 99 and as per guidelines and drawings of NRRDA circular no. DO No. P-17019/6/2006/PII Dated 16 Sept 2009, including providing, laying and compaction of GSB, WMM, OGPC, Seal Coat Type B, as per specifications and appended drawing on both the sides of carriage way up to formation width maintaining rounded hump type shape with bituminous mix material i/c providing and painting of black and white strips, providing and fixing of two no. 600mm equilateral retro reflecting sign boards, i/c cost of all materials, labour T & P & Machinery etc complete on flexible or rigid pavment and as directed by engineer in charge as per relevant clauses of MORD specifications. |
| 31 | Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes. |
| 32 | Plain/reinforced cement concrete in substructure complete as per drawings and technical specification For Parapet Walls/Face Wall (M-15) |
| 33 | Earthwork in excavation for structures as per drawing and technical specifications including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitablematerial. |
| 34 | Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications PCC M-15 |
| 35 | Providing and laying boulder apron for bed protection with stone boulders of minimum size and weight as per Table , no fragmentweighing less than 25 kg laid dry complete as per drawing and technical specifications |
| 36 | Providing and laying filter material underneath pitching in slopes complete as per drawing and technical specifications |
| 37 | Supplying, fitting and placing TMT bar reinforcement in foundation complete as per drawings and technical specifications |
| 38 | Laying Reinforced Cement Concrete Pipe NP4/prestrssed concrete pipe on first class bedding in single row . (Laying Reinforced cement concrete pipe NP4/prestrssed concrete pipe for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation,protection works,backfilling,concrete and masonry works in head walls and parapets . )(1200 mm Dia) |
| 39 | Providing flood gauge marks on substructure as per design including painting complete. |
| 40 | Providing concrete for reinforced concrete in open foundations complete as per drawings and technical specifications R.C.C. grade M 30 |
| 41 | Providing reinforced cement concrete in substructure complete as per drawings and technical specification R.C.C. grade M 30 |
| 42 | Supplying, fitting and placing TMT bar reinforcement in substructrue complete as per drawings and technical specification |
| 43 | Providing weepholes in brick masonry/stone masonry , plain/ reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification |
| 44 | Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification |
| 45 | Providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm with smallersize towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and technical specification |
| 46 | Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications (RCC M-30) |
| 47 | Providing and laying reinforced cement concrete M 30 grade approch sab including reinforement and formwork completeas per drawing and technical specifications (RCC M-30) |
| 48 | Providing and laying cement concrete wearing course M 30 grade including reinforcement complete as per drawing and technical specifications |
| 49 | Reinforced Cement Concrete Crash Barrier (Provision of an Reinforced cement concrete crash barrier at the edges of the road, approaches to bridge structures and medians, constructed with M-40 grade concrete with Fe- 500D TMT reinforcement conforming to IRC:21 and dowel bars 25 mm dia, 450 mm long at expansion joints filled with pre-moulded asphalt filler board, keyed to the structure on which it is built and installed as per design given in the enclosure to MOST circular No. RW/NH - 33022/1/94-DO III dated 24 June 1994 as per dimensions in the approved drawing and at locations directed by the Engineer, all as specified). |
| 50 | Drainage spouts complete as per drawing and technical specifications |
| 51 | P.C.C. M 15 (Sub Structure) ordinary gradelevelling course below approach slab complete as per drawing and technical specifications |
| 52 | Providing and fixing 20 mm thick compressible fibre board in expansion joint complete as per drawing and technical specifications |
| 53 | Supplying, fitting, and placing TMT bar reinforcement in superstructure complete as per drawing and technical specifications ] |
| 54 | Providing and laying pitching on slopes laid over prepared filter media as per drawing and technical specifications |
| 55 | Providing and laying filter material underneath pitching in slopes complete as per drawing and technical specifications |
AI Tender Summary
Tender Timeline
Dec 16, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedDec 31, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedJan 02, 2023
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender