|
| 1 | Sub Estimate No - 1 :- PUMPINGMACHINERY-Item No.1 :- Providing, erecting and giving test of submersible pump set conforming to IS 8034 and motor conforming to IS 9283, with water proof winding. Pump shall be suitable for various delivery head and discharge with stainless steel shaft. Motor suitable for working on 415 V ± 10%, 3 Ph, 50 Hz A.C. Supply, with cable guard, thrust carbon/fiber bearing to withstand entire hydraulic thrust. The pump set shall be suitable for direct coupling, with suitable suction strainer. Pump should have suitable discharge out let as per manufacturer\"s design. Antithrust stream lined non return valve shall be provided with the pump. 3 m submersible copper conductor cable in single / double run and 2 pairs of suitable size erection clamp 10 mm thick shall be provided Submersible Pump 150 mm dia (with Bronze / Stainless steel (CF8M) Impeller) up to 8 stages On percolation well - Discharge / Q = 3.60 Lps, Head -198 & HP = 15 BHP |
| 2 | STAGE |
| 3 | Item No.2 :-Supplying & erecting automatic control panel for 3 Ph, 415 volt, a.c. Submersible/centrifugal pump set upto 20 HP consisting of Star Delta starter having relay range 13-21Amp,S.P.P., Combined ammeter/ voltmeter, phase indicating lamp enclosed in CRCA powder coated Vibration proof enclosure with IP 54 protection. Control Panel should offer single phasing, phase reversal, phase imbalance etc |
| 4 | Item No.3 :- Supplying, erecting & terminating XLPE armoured cable 3 core 10 sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU a) 3 x 10Sq mm Al. cable |
| 5 | Item No.4 :- Providing, erecting, jointing and commissioning Heavy duty, G.I. Pipe for pump suction/delivery as per detailed specification attached.100MM DIA PIPE a) Material |
| 6 | b) Labour 100 mm dia.Pipe |
| 7 | Item No.5:- Supplying and erecting \"B\" class G.I. Bend in position with necessary material100,MMDIA BEND |
| 8 | Item No.6 :- Providing erecting Cast Steel/ Spheroidal Graphite (S.G) Iron D/F Sluice Valves / Butterfly Valves with jointing to pipe work (including all hardware and packing) water works quality, having non-rising spindle with hand wheel and without bypass arrangement, spindle of stainless steel as per requirement, inspection charges, transportation upto departmental store, unloading, stacking, excluding GST levied by GOI & GOM in all respect etc. excluding C. C. foundation / structural steel support. Sluice Valves. CS-150 100 mm dia |
| 9 | Item No.7 :- Providing erecting Cast Steel /Spheroidal Graphite (S.G.) Iron D/F Reflux Valves Single Door with jointing to pipe work (including all hardware and packing) water works quality with jointing to pipe without bypass arrangement, with gunmental seats including inspection charges, transportation upto departmental store, unloading, stacking excluding GST levied by GOI & GOM in all respect etc. completed but excluding C. C.foundation / structural steel support. Reflux valve CS-150 100 mm dia |
| 10 | Item No.8:- Providing, fabricating, erecting, M.S. Flanges sleep on type (all tables) of required size and thickness with both side machined. 100 MM DIA |
| 11 | Item No.9 :- Providing pipe type earthing with 40mm. dia. G.l. pipe or 20 mm dia. G.l. Rod complete with all materials as per specification no. EA-EP |
| 12 | Item No. 10:- Supplying and erecting plywood 12 mm thick fixed to wall or on provided panel board with necessary materials such as screws, wall fasteners supports, nuts bolts etc. complete. |
| 13 | Item No.13 :- Providing, erecting triple spur gear type Chain Pulley Block suitable for capacity as below with 6 M lift complete with load chain and hand chain suitable for above lift, tested to 50% over load as per IS 3832 carrying ISI mark. --- do --- etc. complete. ( 2 Tonne Capacity) |
| 14 | Item No.14 :-Supplying and erecting flat flexible 3 core 10 sq mm PVC sheathed submersible type copper cable suitably clamped at fixed intervals with column pipe assembly complete. |
| 15 | Item No.15 :- Providing & erecting epoxy straight through joint outdoor/indoor for LT XLPE armoured cable 2.5 to 16 sq. mm. cable, with necessary material as per specification no. CB-JT/LT |
| 16 | Item No.16 :- Supplying and erecting porcelain base iron clad cut out of HC type 415V 16A erected on polished wooden block complete |
| 17 | Item No.17:- Supplying and erecting set of 3 pilot lamps all bakelite with colour glasses with miniature lamps 230 V/250V erected on provided CRCA box with panel type fuses and connected with PVC wires |
| 18 | Item No.18:- Supplying and erecting panel mounting type digital voltmeter having three and half digit LED display, calibrated for 0 to 750V AC suitable to operate on 500V AC supply with necessary PVC wire leads and lugs and mounting hardware on provided panel complete with calibration certificate from manufacturer. |
| 19 | Item No.19:- Supplying and erecting panel mounting type digital ammeter having three and half digit LED display, external CT operated, calibrated for suitable to operate on 500V, 0 to 1000A AC supply with necessary PVC wire leads and lugs and mounting hardware on provided panel complete with calibration certificate from manufacturer |
| 20 | Item No.20:- Supplying and erecting bank of All Polypropylene capacitors with the standard capacities of 1, 2, 3, 5, 7, 12.5, 15, 20 and 25 KVAR units of power factor correction for operation on 3 phase, 50 Hz, 400 V+/- 10% with externally discharging resistances, earthing terminals and built on angle iron or channel iron frame work and provided with terminal cover box complete erected and tested. |
| 21 | Item No.18:- Supplying and erecting panel mounting type digital voltmeter having three and half digit LED display, calibrated for 0 to 750V AC suitable to operate on 500V AC supply with necessary PVC wire leads and lugs and mounting hardware on provided panel complete with calibration certificate from manufacturer. |
| 22 | Item No.19:- Supplying and erecting panel mounting type digital ammeter having three and half digit LED display, external CT operated, calibrated for suitable to operate on 500V, 0 to 1000A AC supply with necessary PVC wire leads and lugs and mounting hardware on provided panel complete with calibration certificate from manufacturer |
| 23 | Item No.20:- Supplying, installing, testing & commissioning 3 phase, 11/0.433 kV, 50 Hz., 25 kVA oil immersed and naturally cooled outdoor type, aluminium wound transformer, delta/star connected with additional neutral brought out on load side, temperature rise should not exceed 40oC by thermometer in oil and 45oC by the resistance in winding at full load rating, with standard accessories complete with test certificate with losses below 190 Watts at 50% load, 635 Watts at 100% load as per IS:1180 - 2014, energy efficiency level II, with necessary permissions of Electrical Inspector, as per specification no SS- TR. |
| 24 | Item No.21:- Supplying and erecting bank of All Polypropylene capacitors with the standard capacities of 1, 2, 3, 5, 7, 12.5, 15, 20 and 25 KVAR units of power factor correction for operation on 3 phase, 50 Hz, 400 V+/- 10% with externally discharging resistances, earthing terminals and built on angle iron or channel iron frame work and provided with terminal cover box complete erected and tested. |
| 25 | Sub Estimate No - 2 :- PUMPINGMACHINERY-Item No.1 :- Providing, erecting and giving test of submersible pump set conforming to IS 8034 and motor conforming to IS 9283, with water proof winding. Pump shall be suitable for various delivery head and discharge with stainless steel shaft. Motor suitable for working on 415 V ± 10%, 3 Ph, 50 Hz A.C. Supply, with cable guard, thrust carbon/fiber bearing to withstand entire hydraulic thrust. The pump set shall be suitable for direct coupling, with suitable suction strainer. Pump should have suitable discharge out let as per manufacturer\"s design. Antithrust stream lined non return valve shall be provided with the pump. 3 m submersible copper conductor cable in single / double run and 2 pairs of suitable size erection clamp 10 mm thick shall be providedSubmersible Pump 150 mm dia (with Bronze / Stainless steel (CF8M) Impeller) up to 8 stages |
| 26 | STAGE |
| 27 | Item No.2 :-Supplying & erecting automatic control panel for 3 Ph, 415 volt, a.c. Submersible/centrifugal pump set upto 20 HP consisting of Star Delta starter having relay range 13-21Amp,S.P.P., Combined ammeter/ voltmeter, phase indicating lamp enclosed in CRCA powder coated Vibration proof enclosure with IP 54 protection. Control Panel should offer single phasing, phase reversal, phase imbalance etc |
| 28 | Item No.3 :- Supplying, erecting & terminating XLPE armoured cable 3 core 10 sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU a) 3 x 10Sq mm Al. cable |
| 29 | Item No.4 :- Providing, erecting, jointing and commissioning Heavy duty, G.I. Pipe for pump suction/delivery as per detailed specification attached.100MM DIA PIPE a) Material |
| 30 | b) Labour 100 mm dia.Pipe |
| 31 | Item No.5:- Supplying and erecting \"B\" class G.I. Bend in position with necessary material100,MMDIA BEND |
| 32 | Item No.6 :- Providing erecting Cast Steel/ Spheroidal Graphite (S.G) Iron D/F Sluice Valves / Butterfly Valves with jointing to pipe work (including all hardware and packing) water works quality, having non-rising spindle with hand wheel and without bypass arrangement, spindle of stainless steel as per requirement, inspection charges, transportation upto departmental store, unloading, stacking, excluding GST levied by GOI & GOM in all respect etc. excluding C. C. foundation / structural steel support. Sluice Valves. CS-150 100 mm dia |
| 33 | Item No.7 :- Providing erecting Cast Steel /Spheroidal Graphite (S.G.) Iron D/F Reflux Valves Single Door with jointing to pipe work (including all hardware and packing) water works quality with jointing to pipe without bypass arrangement, with gunmental seats including inspection charges, transportation upto departmental store, unloading, stacking excluding GST levied by GOI & GOM in all respect etc. completed but excluding C. C.foundation / structural steel support. Reflux valve CS-150 100 mm dia |
| 34 | Item No.8:- Providing, fabricating, erecting, M.S. Flanges sleep on type (all tables) of required size and thickness with both side machined. 100 MM DIA |
| 35 | Item No.9 :- Providing pipe type earthing with 40mm. dia. G.l. pipe or 20 mm dia. G.l. Rod complete with all materials as per specification no. EA-EP |
| 36 | Item No. 10:- Supplying and erecting plywood 12 mm thick fixed to wall or on provided panel board with necessary materials such as screws, wall fasteners supports, nuts bolts etc. complete. |
| 37 | Item No.13 :- Providing, erecting triple spur gear type Chain Pulley Block suitable for capacity as below with 6 M lift complete with load chain and hand chain suitable for above lift, tested to 50% over load as per IS 3832 carrying ISI mark. --- do --- etc. complete. ( 2 Tonne Capacity) |
| 38 | Item No.14 :-Supplying and erecting flat flexible 3 core 10 sq mm PVC sheathed submersible type copper cable suitably clamped at fixed intervals with column pipe assembly complete. |
| 39 | Item No.15 :- Providing & erecting epoxy straight through joint outdoor/indoor for LT XLPE armoured cable 2.5 to 16 sq. mm. cable, with necessary material as per specification no. CB-JT/LT |
| 40 | Item No.16 :- Supplying and erecting porcelain base iron clad cut out of HC type 415V 16A erected on polished wooden block complete |
| 41 | Item No.17:- Supplying and erecting set of 3 pilot lamps all bakelite with colour glasses with miniature lamps 230 V/250V erected on provided CRCA box with panel type fuses and connected with PVC wires |
| 42 | Item No.18:- Supplying and erecting panel mounting type digital voltmeter having three and half digit LED display, calibrated for 0 to 750V AC suitable to operate on 500V AC supply with necessary PVC wire leads and lugs and mounting hardware on provided panel complete with calibration certificate from manufacturer. |
| 43 | Item No.19:- Supplying and erecting panel mounting type digital ammeter having three and half digit LED display, external CT operated, calibrated for suitable to operate on 500V, 0 to 1000A AC supply with necessary PVC wire leads and lugs and mounting hardware on provided panel complete with calibration certificate from manufacturer |
| 44 | Item No.20:- Supplying and erecting bank of All Polypropylene capacitors with the standard capacities of 1, 2, 3, 5, 7, 12.5, 15, 20 and 25 KVAR units of power factor correction for operation on 3 phase, 50 Hz, 400 V+/- 10% with externally discharging resistances, earthing terminals and built on angle iron or channel iron frame work and provided with terminal cover box complete erected and tested. |
| 45 | Sub work.4 :R.C.C E.S.R.CAPACITY35000LTR 9 m st ht . Item no 1 : Designing (aesthetically), and constructing RCC ground service reservoirs / RCC sumps in M-300 mix. of required capacity including excavation in all types of strata, foundation concrete, container walls, bottom slab top RCC roof slab / or dome, 20 mm thick cement plaster with water proofing compound in CM 1:3 proportion. to inside face of the container,including epoxy paint from inside including refilling and disposing of surplus stuff within lead of 50 M, all labour and material charges, for laying and jointing of pipe assembly for inlet, outlet washout, over flow andbye-pass arrangement consisting of C.I./ M.S. D/F. pipes, specials and valves of given diameters, providing and fixing accessories such as Stainless Steel ladder inside and outside, C.I. Manholeframe and cover, water top slab, B.B. masonry chamber for all valves, ventilating shafts, including giving satisfactory hydraulic test and water tightness test as per IS code and providing three coats of Acrylic emulsion with Silicon additives Paint to all expose surface of structure including roof surface etc. completeas per design data, criteria, obligatory requirements and detailed specifications. |
| 46 | R.C.C E.S.R.CAPACITY 30000LTR 9 m st ht . |
| 47 | R.C.C E.S.R.CAPACITY25000LTR 9 m st ht . |
| 48 | R.C.C E.S.R.CAPACITY 20000LTR 9 m st ht . |
| 49 | R.C.C E.S.R.CAPACITY25000LTR 9 m st ht . |
| 50 | Item No. 3 : Providing & supplying ISI standard CI double flanged pipes. Inlet Pipe & washout pipes 100 mm CID/F |
| 51 | Inlet Pipe & washout pipes 80 mm CID/F |
| 52 | Inlet Pipe & washout pipes 125 mm CID/F |
| 53 | Item No.4 :Providing and supplying ISI standard CIDF specials of required thickness with 3 coats of approved make epoxy paint (Shalimar, Ciba or Mahindra & Mahindra make) from inside and outside including all taxes (Central and local), octroi, inspection charges, transportation to stores / site, and stacking, etc. complete. |
| 54 | Item No.5 : Providing and supplying double flange sluice valves confirming for IS 2906/14846 including warn gear arrangement as per test pressure stainless steel spindle capsincluding all statutary duties and taxes such as GST levied by Gol and GoM in all respect , transportation etc complete125mm dia sluice valve PN-1 |
| 55 | Item No.5 : Providing and supplying double flange sluice valves confirming for IS 2906/14846 including warn gear arrangement as per test pressure stainless steel spindle capsincluding all statutary duties and taxes such as GST levied by Gol and GoM in all respect , transportation etc complete.100 mm dia sluice valve PN-1 |
| 56 | Sub Estimate No - 5 Rising Main Excavation for foundation/ pipe trenches in earth, soils of all types, sand gravel and soft murum, including removing the excavated material upto a distance of 50 meters & lifts as below, stacking & spreading as directed, normal dewatering,preparingthebedforfoundationand excluding backfilling, etc. complete. |
| 57 | Excavationforfoundation/pipetrenchesinhardmurum and boulders, W.B.M. road including removing the excavatedmaterialuptoadistanceof50Mbeyondthe area and lifts as below, stacking and spreading as directedbyEngineer-in-charge,normaldewatering, preparingthebedforfoundationandexcludingback- filling, etc. complete.-HMB |
| 58 | Excavation for foundation/ pipe trenches in soft rock and oldcementandlimemasonryfoundationasphaltroad including removing the excavated material upto a distance of50Mbeyond areaandliftsasbelow,stackingas directed by Engineer-in-charges, normal dewatering, preparing the bed for foundation and excluding backfilling, etc. complete.-Soft Rock |
| 59 | Excavation for foundation / pipe trenches in hard rock by controlledblasting,includingtrimmingandlevellingthe bedbychisellingwherenecessaryandremovingthe excavatedmaterialandstackingitinmeasurableheaps within a distance of 50 metres from the area and lifts as below, normal dewatering, excluding backfilling, etc. complete. Lift 0 to 1.5 M-Hard Rock |
| 60 | Filling in plinth and floors murum bedding in trenches with approved murum from foundation 15 cm to 20 cm layers including watering and compaction complete. |
| 61 | Item No.6 :-Providing D.I. pipes (push on joints pressure pipes of D. I. of following class and diameters confirming to the I. S. specification inclusive cost of jointing materials (Rubber gasket of EPDM Quality ) excluding GST levied by GOI & GOM in all respect including Third party inspection charges of TPI Agency approved by MJP including Transit insurance, Railway Freight, Unloading from railway wagon, Loading into Truck, Transportation to departmental store, unloading, stacking etc. completed as directed by Engineer in charges (IS 1536/2001 for pipes and I S 158/1969 and IS 12820/1989 or latest edition/ revision with amendments for Rubber Gaskets. 100mm dia. DI-K9 Pipe-L-1915MExt Well to Gaothan ESR and Ext Well ToMalewadi, Bhulewasti ESR\"s-L-1956M |
| 62 | 90mm dia. HDPE 8 kg/cm^2 Ext Well to Thakrwadi ESR-L-628M |
| 63 | ProvidingG.I./P.V.C/HDPESpecialsasperstandard specifications&directionofinchargeEngineer.(5%of Item No.1,2&3) |
| 64 | Item No.8 :-Lowering laying and jointing with SBR ruber gaskets C.I. S/S pipes of various classes with CI / MS specials of following diameter in proper position, grade and alignment as directed by Engineer-in-charge including conveyance of material from stores to site of work, including cost of jointing materials and rubber rings labour etc. complete. 100mm dia. DI-K9 Pipe- |
| 65 | 90mm dia. HDPE 8 kg/cm^2 Ext Well to Thakrwadi ESR-L-628M |
| 66 | HydraulictestingofG.I.pipelinetospecifiedpressure includingcostofallmaterialsandlabourandwaterfor testingforthelengthupto1kmusingreciprocatingtype pumpswhichshouldbeabletoprovidespecifiedtest pressure gauges and other necessary equipments,labour operationchargesetc.requiredfortesting,Therates underthisitemshallalsoincludecostofretestingif necessary and reinstating to original postion. GI Pipe 80 mm Dia M Class |
| 67 | 90mm dia. HDPE 8 kg/cm^2 Ext Well to Thakrwadi ESR-L-628M |
| 68 | ProvidingISImarkG.I.Pipeoffollowingclassanddia. Includingalllocalandcentraltaxes,octroi,inspection charges, transportation to stores. etc. complete. GI Pipe 100 mm Dia M Class |
| 69 | LoweringLaying&jointingG.I.pipesandspecialsof followingclassanddiameterincludingconveyancefrom storestositeofworks,alllabour,givingsatisfactory hydraulictest,etccompleteeitherunderground orin vertical position, as directed by Engineer-in-charge.GI Pipe100mm Dia M Class |
| 70 | HydraulictestingofG.I.pipelinetospecifiedpressure includingcostofallmaterialsandlabourandwaterfor testingforthelengthupto1kmusingreciprocatingtype pumpswhichshouldbeabletoprovidespecifiedtest pressure gauges and other necessary equipments,labour operationchargesetc.requiredfortesting,Therates underthisitemshallalsoincludecostofretestingif necessary and reinstating to original postion. GI Pipe 100 mm Dia M Class |
| 71 | Providing, erecting, connecting double flanged short body pattern tye manually operated Butterfly Valve having body, disc and end cover in graded cast iron to IS 210 Gr. CF 200generallyconforminginBS5155,Syntheticrubber faced ring secured on disc by retaining ring with stainless steelscrewstubshaftofstainlesssteelridinginTeflon bearings excluding C.C. foundation/ structural steel support confirming to IS 3095-1991.- Sluice valves+Sluice valve for washout100 mm Dia |
| 72 | Lowering laying and jointing inposition following C.I.D/F Reflux valves Butterfly valves and sluice valves including cost of all labour joining material, including not bolts and givingsatisfactoryhydraulictestingetc.complete.(Rate for all class of sluice valves) Sluice valves+Reflux valve+Sluice valve washout 100 mm Dia |
| 73 | Item No.14:- Providing and supplying Kinetic Double Orifice type Air Valves confirming to IS 14845 as per MJP’s standard specifications combined with screw down isolating valve, small orifice elastic ball resting on a gun metal orifice nipple, large orifice vulcanite ball seating on moulded seat ring, inlet face and drilled, including insurance, third party inspection charges, loading, unloading, transportation upto departmental stores, excluding GST levied by GOI & GOM in all respect etc. complete. (40mm dia) |
| 74 | Providingandfixinginpositionairvalveshaftincluding providing and fixing GI Medium Class or 6 mm thick M.S. pipe shaft 2.70 M long over branch flange of air valve tee, providingPCCblockofM-150concrete150mmthick aroundtheairvalveteeincludingencasingofvertical shaft in PCC M-150 as shown in type design together with providingandmakingflangedjointswhereverrequired and fixing of air valve over the shaft excluding cost of air valve and branch flanged air valve tee. etc. complete as per type design and as directed by Engineer-in-charge for following diameters of pipe lines (type design attached.) upto 150 mm on Murum & harder strata |
| 75 | Item No.16 :- Valve Chamber with Precast RCC Covers Providing and constructing B.B. masonry valve chamber with 15 cm thick 1:3:6 proportion PCC bedding, excluding excavation, B.B. masonry in CM 1:5 proportion precast RCC frame and cover, etc. complete as directed by Engineer-in-charge.[As above of 90 x 45 cm internal size anddepth upto 1.2 M with precast R.C.C slab cover.] |
| 76 | ProvidingandlayinginsitufollowinggradesofC.C.of trap/granite/quartzite/gneissmetalforfoundationand bedding including dewatering, form work, compacting and curing, finishing etc. complete. |
| 77 | Item No.18 :- Providing and laying in situ Cement Concrete of trap/ granite / quartzite / gneiss metal for RCC work in foundation like raft, grillage, strip foundation and footing of RCC columns and steel stanchions including normal dewatering, form work, compaction, finishing and curing, etc. complete. (By weigh batching and mix design for M250 and M-300 only. Use of L&T, A.C.C., Ambuja, Birla Gold, Manikgad, Rajashree, etc. cement is permitted.) (Excluding M.S. or Tor reinforcement) |
| 78 | Item No.19 :- Providing and laying in situ Cement Concrete of trap/ granite / quartzite / gneiss metal for RCC work in foundation like raft, grillage, strip foundation and footing of RCC columns and steel stanchions including normal dewatering, form work, compaction, finishing and curing, etc. complete. (By weigh batching and mix design for M250 and M-300 only. Use of L&T, A.C.C., Ambuja, Birla Gold, Manikgad, Rajashree, etc. cement is permitted.) (Excluding M.S. or Tor reinforcement) |
| 79 | Refillingthetrencheswithavailableexcavatedstuffwith soft materialfirst over pipeline andthen hardmaterial in 15cmlayerswithallleadsandliftsincluding consolidation, surcharging, etc. complete |
| 80 | Item No.21 :- Providing and fixing in position M.S. air valve boxes fabricated with 2 mm thick M.S. plate, 30 x 30 x 3 mm size M.S. angle frame, concreting in M-150 for fixing the box in position, applying two coats of oil paint, painting chainage, locking arrangement, etc. complete as directed by Engineer-in-charge. |
| 81 | Item No.22 :-Providing and supplying ISI mark CI D/F reflux valves (non-return valves ) of following dia including railway freight, inspection charges, unloading from railway wagon, loading into truck, transportation upto departmental stores, unloading, stacking excluding GST levied by GOI & GOM in all respect etc. complete. Reflux valves as per I.S.5312 Part I (1984) 80 mm dia CI D/F REFLUX VALVE |
| 82 | b) Labour PN-1.6 with out by pass |
| 83 | Sub Estimate No - 6 :- Distribution SystemExcavation for foundation/ pipe trenches in earth, soils of all types, sand gravel and soft murum, including removing the excavated material upto a distance of 50 meters & lifts as below, stacking & spreading as directed, normal dewatering,preparingthebedforfoundationand excluding backfilling, etc. complete. |
| 84 | Excavationforfoundation/pipetrenchesinhardmurum and boulders, W.B.M. road including removing the excavatedmaterialuptoadistanceof50Mbeyondthe area and lifts as below, stacking and spreading as directedbyEngineer-in-charge,normaldewatering, preparingthebedforfoundationandexcludingback- filling, etc. complete.-HMB |
| 85 | Excavation for foundation/ pipe trenches in soft rock and oldcementandlimemasonryfoundationasphaltroad including removing the excavated material upto a distance of50Mbeyond areaandliftsasbelow,stackingas directed by Engineer-in-charges, normal dewatering, preparing the bed for foundation and excluding backfilling, etc. complete.-Soft Rock |
| 86 | Excavation for foundation / pipe trenches in hard rock by controlledblasting,includingtrimmingandlevellingthe bedbychisellingwherenecessaryandremovingthe excavatedmaterialandstackingitinmeasurableheaps within a distance of 50 metres from the area and lifts as below, normal dewatering, excluding backfilling, etc. complete. Lift 0 to 1.5 M-Hard Rock |
| 87 | Filling in plinth and floors murum bedding in trenches with approved murum from foundation 15 cm to 20 cm layers including watering and compaction complete. |
| 88 | Providing and supplying in standard lengths ISI mark rigid unplasticisedPVCpipessuitableforportablewaterwith solvent cement joints including cost of couplers, as per IS specification no. 4985/ 1988 including all local and central taxes, transportation, freight charges, inspection charges, loading, unloading, conveyance to the departmental stores/siteandstackingthesameinclosedshedduly protected from sun rays and rains including cost of jointing material i.e. solvent cement, etc. complete (selffit type to be jointed with cement solvent) 75 mm Dia PVC Pipe 4 Kg/sqcm |
| 89 | 90 mm Dia pvc Pipe 4 Kg/sqcm |
| 90 | 110 mm Dia pvc Pipe 4 Kg/sqcm |
| 91 | 140 mm Dia pvc Pipe 4 Kg/sqcm |
| 92 | ProvidingISImarkG.I.Pipeoffollowingclassanddia. Includingalllocalandcentraltaxes,octroi,inspection charges, transportation to stores. etc. complete. GI Pipe 80mm Dia M Class |
| 93 | ProvidingG.I./P.V.C/HDPESpecialsasperstandard specifications&directionofinchargeEngineer.(5%of Item No.1,2&3) |
| 94 | LoweringLaying&jointing with PVCpipesandspecialsof followingclassanddiameterincludingconveyancefrom storestositeofworks,alllabour,givingsatisfactory hydraulictest,etccompleteeitherunderground orin vertical position, as directed by Engineer-in-charge.75 mm Dia PVC Pipe 4 Kg/sqcm |
| 95 | 90 mm Dia pvc Pipe 4 Kg/sqcm |
| 96 | 110 mm Dia pvc Pipe 4 Kg/sqcm |
| 97 | 140 mm Dia pvc Pipe 4 Kg/sqcm |
| 98 | LoweringLaying&jointingG.I.pipesandspecialsof followingclassanddiameterincludingconveyancefrom storestositeofworks,alllabour,givingsatisfactory hydraulictest,etccompleteeitherunderground orin vertical position, as directed by Engineer-in-charge.GI Pipe 80 mm Dia M Class |
| 99 | HydraulictestingofPVCpipelinetospecifiedpressure includingcostofallmaterialsandlabourandwaterfor testingforspecifiedlengthincludingcutting,placingend cap making arrangement for filling safe water using reciprocating type pumps which should be able to provide specified test pressure gauges and other necessary equipments,labour,operationcharges,etc.requiredfor testing. The rate under this item shall also include cost of retesting, if necessary and reinstating to original position.75 mm Dia PVC Pipe 4 Kg/sqcm |
| 100 | 90 mm Dia pvc Pipe 4 Kg/sqcm |
| 101 | 110 mm Dia pvc Pipe 4 Kg/sqcm |
| 102 | 140 mm Dia pvc Pipe 4 Kg/sqcm |
| 103 | HydraulictestingofG.I.pipelinetospecifiedpressure includingcostofallmaterialsandlabourandwaterfor testingforthelengthupto1kmusingreciprocatingtype pumpswhichshouldbeabletoprovidespecifiedtest pressure gauges and other necessary equipments,labour operationchargesetc.requiredfortesting,Therates underthisitemshallalsoincludecostofretestingif necessary and reinstating to original postion. GI Pipe 80 mm Dia M Class |
| 104 | Providing, erecting, connecting double flanged short body pattern tye manually operated Butterfly Valve having body, disc and end cover in graded cast iron to IS 210 Gr. CF 200generallyconforminginBS5155,Syntheticrubber faced ring secured on disc by retaining ring with stainless steelscrewstubshaftofstainlesssteelridinginTeflon bearings excluding C.C. foundation/ structural steel support confirming to IS 3095-1991.- Sluice valves+Sluice valve for washout80 mm Dia |
| 105 | Lowering laying and jointing inposition following C.I.D/F Reflux valves Butterfly valves and sluice valves including cost of all labour joining material, including not bolts and givingsatisfactoryhydraulictestingetc.complete.(Rate for all class of sluice valves) Sluice valves+Reflux valve+Sluice valve washout 80 mm Dia |
| 106 | Item No.12 :- Providing and constructing B.B masonry valve chamber with 15 cm thick 1:3:6 proportion PCC bedding, excluding excavation, B.B. masonry in CM 1:5 proportions, precast RCC frame and cover, etc. complete as directed by Engineer-in-charge. (Size 0.60 x 0.45 M x 0.90M) |
| 107 | Item No.13 :- Providing and fixing C.I. road box including loading, unloading and carting to site of work including all necessary excavatio in all types of strata and fixing in murum packing, etc. complete. 225 mm x 300 mm (40 kg) |
| 108 | ProvidingandlayinginsitufollowinggradesofC.C.of trap/granite/quartzite/gneissmetalforfoundationand bedding including dewatering, form work, compacting and curing, finishing etc. complete. |
| 109 | Item No.18 :- Providing and laying in situ Cement Concrete of trap/ granite / quartzite / gneiss metal for RCC work in foundation like raft, grillage, strip foundation and footing of RCC columns and steel stanchions including normal dewatering, form work, compaction, finishing and curing, etc. complete. (By weigh batching and mix design for M250 and M-300 only. Use of L&T, A.C.C., Ambuja, Birla Gold, Manikgad, Rajashree, etc. cement is permitted.) (Excluding M.S. or Tor reinforcement) |
| 110 | Refillingthetrencheswithavailableexcavatedstuffwith soft materialfirst over pipeline andthen hardmaterial in 15cmlayerswithallleadsandliftsincluding consolidation, surcharging, etc. complete |
| 111 | Item No.1 :- Commissioning, running and maintaining the scheme to quantities, rated capacity, including manning necessary personnel such as operator, valveman, etc. as per requirements of the scheme and whoshould also administer chemical dose for a period of 1 month for individual scheme and for regional scheme, together with training of personnel spared by MJP / Local Body and handing over the scheme to Local Body after completion of the above period as directed by Engineer-in-charge.Note : Required chemicals to be supplied by Department free of cost and electricity bill will also be paid by the Department. |
| 112 | Item No.3 :- Providing and fixing board displaying information, such as \"Name of work, Tender cost, Name of Contractor, Work completion and liability period etc\", having rectangular shape of 1.20m x 0.90m size made out 18 gauge (1.25mm) thick mild steel sheet painted with one coat of Zinc chromate stoving primer and two coats of enamel paint on front side and grey stove enamel on back side and border / messages / symbols etc. complete.Spec. No. As directed by Engineer in Charge |
