Tender For Conversion Of Existing Sad At Village Maur Kalan Into Mohalla Clinic District Bathinda., Bathinda-Punjab

TDR : 35227313

Tender Notice
BOQ

Expired

Bathinda , Punjab

Tender Brief : Tender For Conversion Of Existing Sad At Village Maur Kalan Into Mohalla Clinic District Bathinda.

Document Fees
₹ 5000 /-

EMD
₹ 48700.0 /-

Tender Value
₹ 24.34 Lakhs /-

Submission Date
19-12-2022

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Providing Vitrified tile & Enterance flooring after Dismentling of Existing Flooring
2	Dismantling glazed tiles (to be carefully removed).
3	Providing and laying vitrified floor tiles in different sizes in light colour shades made using Full Body Technology (thickness to be specified by the manufacturer) with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 fine sand), complete. ( Full body vitrified tiles have pigment in entire body / thickness of tile which makes chips and scratches less noticeable and make na ideal choice for high traffic zones.)
4	Size 600x600 mm
5	Grouting the joints of flooring tiles having joints of 3 mm width, using2mm to 3 mm gap using spacersand later this gap to be filled with cement basedgrout ) with Cement base grout and matching pigments etc., complete, including filling / grouting and finishing complete as per direction of Engineer-in-charge.
6	Size 600x600 mm.
7	Providing and Laying Tactile Flooringfull body vitrified , low water absorption below 5%, having excellent slip resistance , very dense, durable and abrasion resistant, solid through colour, fade proof, highly chemical and stain resistance unglazed finish porcelain tile of size 300mm x 300mm x 10mm + 5mm thick, approved profile design, Tec-button/Tec-liner laid in ordinary grey cement and on 20mm thick bed of cement mortar 1:3 filling neat cement slurry between jointswith WhiteCement containingpigment to match the shade complete in all respect. (Tile design and patternwill be as per guidelines issued for persons with disability)
8	Providing and Installation of Safety signage as per guideline for person with disability made ofretro reflectivesheeting as per colour specified and writing matter will be ofsame material in whitefixed / pasted over 4mm thick aluminum composite sheet, including cost of writing matter with braille also firmly fixed on wall with nylon fastener, brass screw and washercomplete as per specification and as desired by engineer in charge.
9	Marble stone flooring with 12-15 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with :
10	Udaipur Green Marble Tiles ofthickness 12mm to 15mm
11	Slabs sizes above 0.50 sqm
12	Marble work of thickness 12-15 mm for wall lining (veneer work), backing filled with a grout of average 12 mm thick in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment to match the marble shade (To be secured to the backing by means of cramps, which shall be paid for separately).
13	Udaipur Green Marble Tiles ofthickness 12mm to 15mm
14	Slabs sizes above 0.50 Sqm
15	Extra labour for projected nosing of stair case of any shape and design
16	Providing and laying 50 mm wide antiskid tape made of slip resistant material colour contrast, edge strip, self adhesive to be fixed onfront edge of Stair treads to help people with visual disabliity and elderly even in dim light conditions &reduce the risk of slipping Make 3M or equivalent brand complete as per specifications, Harmonised guidelines for PwD and as desired by engineer-in-charge.
17	Providing and laying 25 mm to 50mm wide high intensitiy reflective conspicuity tape colour contrast, edge strip, self adhesive to be fixed onfront edge of Stair riser to help people with visual disabliity and elderly even in dim light conditions &reduce the risk of slipping Make 3M or equivalent brand complete as per specifications, Harmonised guidelines for PwD and as desired by engineer-in-charge.
18	Partition, Ceiling & Painting Work
19	Dismantling brick work tile, masonry or tile liningIn cement
20	20mm thick cement plaster 1:4 in two coat work.
21	Providing and fixing partition 74 mm overall thickness partitionupto ceiling height consisting of G.I. frame and with 12 mm thick double BISON Board including providing and fixing of frame work made of special section power pressed/ role form G.I. sheet with zinc coating of grade 175 consisting of floor and ceiling channel 50mm wide having equal flanges of 32mm and 0.5mm thick fixed to the floor and ceiling at the spacing of 610mm centre to centre with dash fastener of 12.5mm dia-meter,40mm length and the studs 48mm wide having one flange of 34mm and other flange 36mm and 0.50mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610mm centre to centre by 6mm dia bolts and nuts at both ends of partition fixed flush to wall with rawl plugs at spacing 450mm centre to centre and fixing of boards to either side of frame work by 25mm drive all screws on studs, floor and ceiling channels at the spacing of 300mm centre to centre, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, joint finisher and two coats of primer suitable for board as per manufacture’s specificatior and direction of engineer-in-charge all complete.
22	Providing & fixing wooden Partition having internal frame work of Kail wood section 50mm x 50mm, 6mm thick waterproof ply on both sides finished with 1mm thick mica complete as per architect drawing & as desired by Engineer-in-Charge
23	Providing & fixing wooden frame/Chowkhat for fixed glazing & Door Chowkhat having sal wood section 50mm x 50mm, 6mm thick waterproof ply on both sides finished with 1mm thick mica complete as per architect drawing & as desired by Engineer-in-Charge
24	Factory manufactured solid flush door fixed in positioniron hinges, etc . (excluding the cost of any fittings other than specified above but including the labour for fxing the same in position a) comercial with elm or gujan facing on both/sides with laminated core and lipped edges. iv) 35mm thick.
25	Commercial with elm or gurjan facing on both\Sides with laminated core and lipped edges:-
26	35mm thick.
27	Providing and fixing high pressure laminated sheet 1 mm thick.
28	Cost of aluminum fittings complete for doors, windows such as tower bolts, handles,Stoppers and screw etc. for these fittings (Excluding sliding bolt)For shutter area above 0.50 sqm
29	For shutter area above 0.50 sqm
30	Providing & Fixing glass panes with nails and putty or wooden strip complete in all respectGlazing area above 0.09 sqm
31	Glazing area above 0.09 sqm
32	5.0mm thick Plate glass (INDIAN)
33	Providing, fixing Glass frosted film on glass existing fixed at site complete as per specification & as desired by Engineer-in-Charge.
34	Providing and fixing hydraulic door closer ISI mark with necessary screw etc. completeI.S.I Designation No. III (size of door 851mm to 1000mm)
35	size of door 851mm to 1000mm
36	Supply & Fixing ofpressed steel frames (Chowkats) consisting of 18 gauge (1.25mm) thick steel sheet ofthe specified section(standard design latest) including iron lugs (hold fasts) iron hinges, confirming to P.W.D. specifications including bolts for fixing stops, lock-notch provision for receiving tower bolts, Hydraulic spring and finished with one priming coat of approved quality, fixed in position, including the cost of cement concrete 1:3:6 for filling in the frame and cement concrete 1:2:4 for lugs complete.
37	Doors and windows frame of size 151mm x 60mm with 35 mm wide double rebate weighing 3.95 kg/rmt
38	Providing & fixing of Box type steel windows, made of various ERW section outer 60mm x 25mm, central mullion 60mm x 25mm, for shutter 50mm x 20mmhaving thickness of1.25mm (18 gauge), shash bar MS Tee 25mm x 3mmwhere required joints mitered and electrically flash-welded, with iron fittings including necessary iron handles, hinged cleat, tower bolts, iron hold fast and pintle hinges complete (excluding glazing and wire gauge) and finished with ready mixed paint red lead non setting primercomplete as per specification, Drawings and to the entire satisfaction of engineer-in-charge. (Note:- Glazing, wire gauge and grill will be paid as per respective items)
39	Extra for providing & fixing Steel beading of approved shape steel tube beading size 12mm X 12mm, 18 gauge of approved shape and section with screw for fixing of glass panes instead of glazing clips and metal slash putty in steel doors , windows & Ventilators complete in all respect
40	Wrought iron & Mild steel ladders, framed grills, gratings etc. with ends of bars riveted or molded forged framed window guards, barred iron doors stair case iron railing etc. including cost of bolts and nuts, screws, welding rod complete fixing in position
41	Supplying and fixing glass panes with glazing clips and special metal sash putty of approved make.Glass panes 4mm thick above 0.40 sqm area.
42	Glass panes 4mm thick above 0.40 sqm area.
43	Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminum doors including necessary cutting and making good etc. complete.
44	Providing and fixing beading to door and windows chowkats of commercial hard wood, such as Hollock, Champ, Chirassy Chaplash etc (Non coniferous timber other than teak conforming to ISI specification no 100., kiln seasoned) with iron screws, fixed in position complete as per design and shape required50mmx12mm
45	Finishing ofbeading section 50mm x 12mm with Enamel paint two coat work with one coat of primer including preparation of surface complete as per specifications and as desired by Engineer-in-Charge.
46	Providing & fixing 16 guage stainless steel pipe railing of grade 304 duly fixed on steps with the help of bolts grouted on steps with hand rail and newel post of 50mm dia Stainles steel pipe, Balusters of 40mm dia stainless steel pipe complete in all respects.
47	Providing and fixing SS Braile indicators of size 170mm x 35mm to be fixed on handrails of the the approved design and make having Braile dots raised 0.5mm above base plate, to the installed at the specified locations as per the directions of the Engineer-in-Charge complete s per design/specifications and guidelines as per the entire satisfaction of the Engineer-in-Charge
48	Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflection > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, F
49	With 16 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.55 to 0.6) size 595x595 mm
50	Providing and Fixing ceiling consisting of 12.5mm thickGypsum Board of any size G.I. Cradling hanged from the ceiling by means of G.I. hanger complete as per drawings,specifications and tothe entire satisfaction of engineer-in- charge.
51	Scraping White wash and colour wash
52	Providing and fixing of Back Panel of Reception comprising of framing of 50mm x 50mm Partal/ Kail wood or equivalent with 3mm thick backing of Bakelite sheet on wall side,6mm thick waterproof ply on both sides and front portion fixed with 1mm thick laminate of colour and shade to be approved by Architect.Grooves in laminate or elsewhere to be provided as per architectural drawing. The make of ply and laminate and colour of laminate shall be provided as per approval by Architect/ Engineer-in-charge
53	Providing & fixing 6mm thick BISON board waterproof paneling on wall with the help of PVC gatti & SS Screws upto 3\"-6\" high on periphery wall of inside hall complete as per drawing & desired by Engineer-in-Charge
54	Painting two or more coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade. Including priming coat & preparation of surface
55	Providing & applying heritage granual homogeneous wall finishing system from Bakelite Coating & Paints Pvt. Consisting of two component system of dry Granual (25 kg/pack) made of 92% silice particle, coated with fade resistant pigmants and 100% acrylic co-polymers bonding agent (5 ltr pack) with the applied thickness of coating being between 0.8 to 1.2mm to be applied in single coat on a cured level smooth plastered, as per the shade combination approved and as per manufacturer specification, all complete inclusive of primer on the base.
56	Distempering with Acrylic washable oil bound distemper (of approved manufacture) two or more coats over one priming coat to give an even shade
57	Applying priming coat with metal primer on new steel or iron work including preparation of surface.
58	Painting two or more coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade.
59	Finishing walls with Premium Acrylic smooth exterior paintwith silicon additives of required shade with two or more coats applied @ 1.43litre/10 Sqm over and including base coat of water proofing Cement Paint applied @ 2.20 Kg/10 Sqm
60	Providing Signage & Providing New Colour ACP Sheet after Removing of existing ACP Sheets
61	Providing & fixing ACP Sheets of various thickness High Class ISI markedcomplete in all respect as per the directions of Engineer-in-charge.3mm thickACP Sheet
62	Writing matter on front signage Using highintensityMicroprismaticgrade retroreflective SheetingType IV as per ASTM D 4956 09 and as per IRC 67 2012
63	Providing and Fixing Name Plates of various sizes made of PVC sheet printed with self adhesive tape pasted on sunboard complete as desired by Engineer-in-Charge
64	Providing and Fixing Letters of “MOHALLA CLINIC” in SS 304 grade. Height and font as per approved drawing
65	Repair of Existing damages i.e regrading of tile terracing,replacement of glazing, replacement of chequred tile on ramp, replacement of parking pavers.
66	Taking out existing CC interlocking paver blocks from footpath/ central verge/pavement, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge.
67	Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M-35 grade machine made rubber moulded smooth finish with strong vibratory process or with vibro- hydraulic compaction machine and of approved size and design / shape laid in Ordinary Grey and pattern over and including 40 mm thick compacted bed of coarse sand, filling the joints with fine sand etc, all complete as per directions of Engineer-in-Charge.IS COde : 15658 (2006)
68	Extra Cost for using darker fast shade for interlocking pavers Tiles of any shape & thickness instead of grey colours.
69	Regrading terracing of mud plaster covered with tiles or bricks in cement by dismantling tiles or bricks, removing mud plaster, preparing the surface of mud plaster to proper, slope, relaying mud plaster Gobri leaping and tiles or bricks grouted in cement mortar 1:3 (1 cement and 3 fine sand) including replacingunserviceable tiles, or bricks with new over and disposal of unserviceable material to the dumping ground within 50 m lead (The cost of new tiles or bricks excluded).
70	Cost of new tile to be replaced instead of broken tiles in regrading of tile terracing including loading / unloading & all leads as desired by Engineer in charge .
71	Cement concrete 1:2:4 gola 10cm x 10cm concave quadrant along junction of roofs with parapet wall finished smooth, where specially specified.
72	Top khurra 0.6m x 0.6m for rain water pipe in 25mm thick cement concrete 1:2:4 over 50mm thick cement concrete 1:8:16.
73	Providing and fixing in position gratings 150mm x 150mmon top Khura PVC grating
74	Dismantling brick or flagged stone flooring without concrete base.
75	Providing and Laying Out DoorPrecast Designer chequered tiles of any size & any shape 25mm thickness having top layer of white cement mixed with pigment, laid on 20mm thick bed of ordinary cement mortar 1:3(1 ordinary cement :3 fine sand), joints grouted with white cement slurrycontainingpigment to match the shade complete in all respect as per specifications and to the entire satisfaction of engineer- in- charge.
76	Renewing glass panes with putty and nails wherever necessaryGlass panes weighing 10.75 Kg/sqm
77	Reception Counter including panneling on back complete
78	Providing and fixing at site the Reception Table plan dimensions as 5’-6” x 4’6” and height 2’-3” with storage, drawers, space for legs, etc complete as per drawing. The table should be sturdy and stable and will comprise of knot-free teak wood, wherever required, 19mm/ 12mm/ 6mm water proof ply and 1mm laminates of Make and Colour to be approvedby Architect/ Engineer-in-charge. The item also includes hardware such as drawer channels, handles, etc of make and design to be approved by Architect/ Engineer-in-charge. The item also includes all types of consumables such as nails, screws, fevicol, tape, etc and polishing, if required.Grooves, wherever required as per drawing, are also included in the item.complete as per drawing/design as desired by Engineer-in-Charge.
79	Providing and fixing at site the Pharmacy Counter plan dimensions as 5’-3” x 1’-101/2” and height 2’-6” with projected shelve, storage, drawers, space for legs, etc complete as per drawing. The Counter should be sturdy and stable and will comprise of knot-free teak wood, wherever required, 19mm/ 12mm/ 6mm water proof ply and 1mm laminates of Make and Colour to be approvedby Architect/ Engineer-in-charge. The item also includes hardware such as drawer channels, handles, etc of make and design to be approved by Architect/ Engineer-in-charge. The item also includes all types of consumables such as nails, screws, fevicol, tape, etc and polishing, if required.Grooves, wherever required as per drawing, are also included in the item.complete as per drawing/design as desired by Engineer-in-Charge.
80	Construction of Passage from Parking to Towards Toilet
81	Construction of embankment with good quality earth obtained from borrow pits including compensation of earth, loading, unloading, carriage to site of work, spreading, grading to required slope and compacting to meet requirement of table 300-2 as per technical clause 305 of MORT&H specifications.
82	Cement concrete 1:5:10 with 40 mm gauge stone ballast.using concrete mixing volumetric type
83	Providing and laying 60 mm thick factory made cement concrete interlocking Paving blocks of M-35 grade manufacturedby block making machine equipped with steel mould clamped to a strong vibratory table with hydraulic pressure for compaction of concrete as per IRC SP 63 -2014 and of approved size and design / shape laid in Ordinary Grey Colour and pattern over and including 40 mm thick compacted bed of coarse sand, filling the joints with fine sand etc, all complete as per directions of Engineer-in-Charge.
84	Extra Cost for using darker fast shade for interlocking pavers Tiles of any shape & thickness instead of grey colours.
85	Earth work in excavation in foundations, trenches etc. in all kinds of soil where pick jumper work is not involved and not exceeding 2.0 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation and subsequent filling around masonry in 15 cm. layers with compaction including disposal of all surplus soil as directed within a lead of 30 metres.
86	First class burnt brick work laid in cement sand mortar 1:6 in foundation and plinth.
87	Base course of floor consisting of 100mm thick cement concrete 1:8:16 with stone aggregate 40mm guage and 100mm fine sand filling using mechanical mixer for mixing of material
88	20mm thick cement plaster 1:4 in two coat work.
89	Dismantling brick or flagged stone flooring without concrete base.
90	Providing and Laying Out DoorPrecast Designer chequered tiles of any size & any shape 25mm thickness having top layer of white cement mixed with pigment, laid on 20mm thick bed of ordinary cement mortar 1:3(1 ordinary cement :3 fine sand), joints grouted with white cement slurrycontainingpigment to match the shade complete in all respect as per specifications and to the entire satisfaction of engineer- in- charge.
91	New items
92	Providing & fixing of Box type steel windows, made of various ERW section outer 60mm x 25mm, central mullion 60mm x 25mm, for shutter 50mm x 20mmhaving thickness of1.25mm (18 gauge), shash bar MS Tee 25mm x 3mmwhere required joints mitered and electrically flash-welded, with iron fittings including necessary iron handles, hinged cleat, tower bolts, iron hold fast and pintle hinges complete (excluding glazing and wire gauge) and finished with ready mixed paint red lead non setting primercomplete as per specification, Drawings and to the entire satisfaction of engineer-in-charge. (Note:- Glazing, wire gauge and grill will be paid as per respective items)
93	Wire gauge fixed in steel windows, of standard rolled steel section with 3mm thick flat iron cover moulding of 12.5 mm width, fixed with machine screws, complete in all respects
94	Extra for providing & fixing Steel beading of approved shape steel tube beading size 12mm X 12mm, 18 gauge of approved shape and section with screw for fixing of glass panes instead of glazing clips and metal slash putty in steel doors , windows & Ventilators complete in all respect
95	Providing and fixing aluminum work fordoors, windows, ventilators and partitions with extruded built up standard tubularsections/appropriate z sections and other sections conforming to Is: 733 and IS : 1285 of Jindal, Hindalco, Mahavir or equivalent make approved by Engineer in Charge , fixed with rawl plugs and screwsor with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sideswith required PVC Plug/neoprene felt etc. aluminum sections shall be smooth, rust free, straight, mitered and jointedmechanically wherever required including cleat angle, aluminum snap beading forglazing/paneling, C.P.brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer-In-Charge. (Glazing and paneling to be paid for separately) :
96	For shutters of doors, windows & ventilators including providing andfixing hinges/pivots and labour for fixing of fittings wherever requiredincluding the cost of PVC Plug / neoprene gasket required
97	Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in paneling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawingsand directions of Engineer-In-Charge. Prelaminated particle board with decorative lamination on Both side.
98	Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with PVC Plug/ neoprene gasket etc. complete as per the architectural drawings and the directionsof engineer-in-charge . (Cost of aluminum snap beading shall be paid in basic item)
99	Float glass panes of 5 mm thickness
100	Reinforced cement concrete M-20 mechanically batch mixed using batch typeconcrete mixer as per IS:1791 and vibrated by needle vibrator but excludingsteel reinforcement centring andshuttering infoundation and plinth.
101	Reinforced cement concrete M-20 mechanically batch mixed using batch typeconcrete mixer as per IS:1791 and vibrated by needle vibrator but excludingsteel reinforcement centring andshuttering in Superstructure
102	Cold twisted detormed (Ribbed/ Tor steel) Bars (Fe 500 grade as per IS 1786-2008) , for R.C.C works, where not including in the complete rate ofRCC including bending and binding placing in position complete
103	Shuttering for faces of concrete foundations and foundationbeam & plinth beam (vertical or battering)
104	Centering and shuttering for flat surfaces such as suspended floors, roofs, landings, chajjas, shelves etc.
105	Preparation of plastered or concrete surface for painting (including sand paperingthe surface) using ready mixed cement based wall putty by applying two or more coats to get required finish
106	Applying priming coat with cement primer in all shade on newly plastered or concrete exterior surface
107	Wall painting with plastic emulsion paint of approved brand and manufacturer to give an even shade (two or more coats)
108	Sub Estimate for Furniture Items
109	Chair for Receptionist & Pharmacist- Providing and supplying mid back chair with ergonomic design, comfortable & aesthetically appealing. The seat shall be made of 15mm thick hot pressed commercial plywood upholstered with high resilience moulded polyure
110	Waiting Area chair 3 seater- Supply of 3-seater airport style waiting chairs of minimum size 1695mm (L) x 620mm (D) x 775±10 mm (H), in knock down condition, having minimum weight of 35 kg with the following specifications: The chair should have two arms
111	Waiting Area chair 2 seater - Supply of 2-seater airport style waiting chairs of minimum 775±10 mm (H), in knock down condition, having the following specifications: The chair should have two arms at ends. The seat and back should be made of perforated mi
112	Doctor Table- Supplying & Placing executive table with credenza unit in completely knock down conditions with an overall size 1500-1600mm X 1600-1800mm X 750mm that is to be assembled at site. The worktop shall have the size 1950mm X 900mm made up of 25mm
113	Main chair for Doctor- Providing and supplying a high back chair with ergonomic design, comfortable & aesthetically appealing. The seat and back shall be made of 15mm and 12mm thick hot pressed commercial plywood padded with high resilience moulded polyur
114	Visitor Chair for Doctor- Providing and supplying a visitor chair with ergonomic design, user comfort & aesthetically appealing. The seat and back shall be made of 12-15mm thick hot pressed commercial plywood padded with high resilience moulded polyuretha
115	Examination Table for Doctor Room -Providing and Placing in position Examination Table. Overall size of the table shall be 1830 mm L x 560-600 mm D x 810-850 mm H. The examination table shall be made of sturdy structure and shall have a ratchet mechanis
116	Stool for Doctor, Pharmacist Room & in SamplingRoom - Revolving Stool, SS Top, Powder Coated, Height Adjustable (510mm - 690mm). complete as per sample approved by Architect & desired by Engineer-in-Charge.
117	Storage for Medicine - Providing, supplying and placing steel almirah. The overall size of the Almirah shall be 915mm (W) X 485mm (D) X 1980mm (H). The Almirah shall be supplied with 2 nos. of glass doors with4 nos. of adjustable shelves i.e. 5 loading
118	Customized Lab Table- Supplying & placing storage unit with an overall size 900mm X 600mm X 760mm. It should be made up of Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top of the shutter
119	Providing and placing moveable 3-fold screen of MS fame with green coloured curtain, having arrangements that it can be removed for washing and refixed. The overall dimension of the 3-fold screen will be 1675mmx2450mm around examination table. The MS fram
120	Providing and fixing Roller Blinds at the designated locations with fabric/ texture complete as per sample approved by Architect & desired by Engineer-in-Charge.
121	PUBLIC HEALTH SERVICES
122	Providing and fixing in position Chinaware European type water closet P trap or S trap (to the approval of the Engineer-in-charge) suite-consistingof 10 ltr. PVC flushing cisternsupportedonangleironbracket, shortbend32mmdia includingcostof solid white cover complete in all respect and totheentiresatisfactionofengineerin charge.
123	For Public Toilet
124	Providing and fixing in position vitreous chinaware white lavatory suites of approved make (to the approval of Engineer-in-charge) consisting of C.P. brass waste 32mm dia with one C.P. brass pillar tap including Rack Bolt Screw Pair 115mm long complete in all respect.
125	Size 550mm x 400mm
126	For Doctor Room toilet,Pharmacistand Public Toilet
127	Providing and fixing in position C.P. brass soap dish of approved make (to the approval of Engineer-in-charge ) fixed into wall with rawl plugs and C.P brass screws complete in all respect.
128	For Doctor Room toilet,Pharmacistand Public Toilet
129	Providing & Fixing in position 5mm thick bevelled edge mirror of superior glass (of approved make) complete with 4mm thick hard board backing fixed in with rawl plugs 50mm, C.P. brass screws and washers and S/S Studs on top complete in all respect (as required by the Engineer-in- Charge)
130	Size 600mm x 450mm
131	For Doctor Room toilet,Pharmacistand Public Toilet
132	Providing & Fixing in position stop cock / Angle valve of approved make (to the approval of Engineer-in-charge) complete in all respect.
133	C.P.brass 15mm Concealed stop cock with flange.
134	For Doctor Room toilet,Pharmacistand Public Toilet
135	C.P. brass 15mm Angle Valve without flange
136	For Doctor Room toilet,Pharmacistand Public Toilet
137	Providing & Fixing in position 15 mm i/d bib cock of approved make (to the approval of Engineer-in-charge )complete in all respect.
138	C.P. brass Bib cock long nose/ long body foam flow without flange
139	For Doctor Room toilet,Pharmacistand Public Toilet
140	C.P. brass Bib cock foam flow without flange
141	For Doctor Room toilet,Pharmacistand Public Toilet
142	Providing & Fixing in position C.P. Brass flange Dome of approved make (to the approval of Engineer-in-charge ) under various fixtures complete in all respect.
143	For Doctor Room toilet,Pharmacistand Public Toilet
144	Providing and fixing P.V.C Waste Pipe Collapsible 32mm complete in all respect.
145	For Doctor Room toilet,Pharmacistand Public Toilet
146	Providing & fixing in position PVC flexible tube connection of approved make (to the approval of Engineer-in-charge) complete in all respect.
147	PVC tube connection of size 15 mm x 450 mm with C.P. Brass nut
148	For Doctor Room toilet ,Laband Public Toilet
149	Providing & placing in position on terrace (at all floor levels) HDPE water storage tanks of approved make (to the approval of Engineer -in- charge) with cover with suitable locking arrangement and making necessary holes for inlet, outlet and over flow pipes but without fittings and base support for tank.
150	Triple Layer Tanks
151	Providingandfixing inposition towelrails/ringofapprovedmake(totheapprovalof Engineerincharge ) fixed in with rawl plugs embedded in walls with brass screws complete in all respect.
152	C.P. Brass Towel Ring
153	For Doctor Room toilet ,Laband Public Toilet
154	Providing & Fixing of position GI tank nipple of approved make in PVC water storage tanks complete in all respect.
155	GI tank Nipple 25mm i/d
156	Dismantling Sanitary Fixtures Such as European/Indian/Orissa W.C.,PVC/chinaware Cistern Wash hand Basin Urinal Pot Sinks And C.P Fittings and Disposal of Dismantled Material with in a Distance of 100 mtr Complete in all respects
157	European/Indian/Orissa W.C
158	For Doctor Room
159	PVC/ chinaware Cistern
160	For Doctor Room toilet ,Laband Public Toilet
161	Wash Hand Basin/Urinal Pot
162	For Doctor Room toilet ,Laband Public Toilet
163	CP Bib Cock/angle Cock /Stop Cock
164	For Doctor Room ,Pharmacist and Public Toilet
165	Providing and fixing jet spray with 2\"6\" long PVC pipe
166	with C.P. Brass Nut
167	For Doctor Room,Public and Pharmacist
168	Base course of floor consisting of 100mm thick cement concrete 1:8:16 and 100mm sandfilling
169	For Public Toilet
170	Providing and laying Anti skid Ceramic floor tiles of size 300x300 mm x 10 mm thick of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on flooring skirting and dado in 12.5mm thick cement plaster 1:3 in base and jointed with @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., completewhite cement slurry in joints including corners angles and beading..
171	For Public Toilet
172	Providing and fixing 1st quality ceramic glazed wall tiles Matt/Semi Matt/Glosy/Highly Gloss finish/Highlighter/emboss conforming to IS : 15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of size 200 x 300 mm, 100x200mm,200x200mm as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:4 (1 cement: 4 fine sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.
173	For Doctor Room, Pharmacist Room & Public Toilet
174	D/d Door
175	Providing & Fixing in position SWR UPVC anti Syponage pipe double socketed
176	B type 110 mm o/d
177	For Public Toilet
178	Providing & Fixingin position SWR UPVC Specials For Soil Waste vent or anti Syponage pipe.
179	For110 mm o/d
180	P Trap- Floor Trap 110x110mm
181	For Public Toilet
182	Elbow 90 Degree
183	For Public Toilet
184	Single TEE
185	For Public Toilet
186	Providing and fixing in position gully traps fixed in cement concrete 1:4:8 complete with Grating 150mm x 150mm, cover and frame clear opening 300mm x 300mm and out of side size 330mm x 330mm and chamber including cost of all bricks work in cement morter 1:5 cement concrete 1:2:4 in coping around cover and frame etc. as per standard design minimum depth of water should be 150 mm with a minimum seal 50mm.
187	100mm internal Diametre S.W.gully trap with H.C.I. grating and cast iron cover weighing approximately 7.26 kg. and frame clear opening 300mm x 300mm and out of side size 330mm x 330mm
188	For Public Toilet
189	Providing, laying, jointing, fixing and testing ISI Marked uPVC Pipe with G.I. specials as per ISI-4985, including cost of G.I. specials such as tees, bends, sockets, elbows etc. testing inside building complete.
190	uPVC Pipe 10 Kgf/cm2
191	For Public Toilet
192	CONCEALED IN WALL: Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes as per IS 15778 (ISI marked with the prior approval of Engineer-in- Charge), having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing including jointing of pipes & fittings, with one step CPVC solvent cement and testing of pipes complete as per direction of Engineer-in-Charge.
193	CPVC SDR 11 Pipe & fitting 16mmo/d
194	For Public Toilet
195	Providing & fixing in position vitreous Chinware white Indian make flat back or angular lipped front small urinals size 265x315x440mm approved make (to the approval of the Engineer-in-charge) with C.P. brass tube connection 300 mm long complete in all respect.
196	For Public Toilet
197	Construction of Septic Tank as per the detail attached.
198	For Public Toilet
199	Construction ofSoakage pit as per the detail attached
200	For Public Toilet
201	Dismantling of wall tiles at any floor of the building, laid in cement mortar including scraping of cement plaster and disposal of malba at a suitable place within a distance of 100 Mtrs of the complex complete in all respect
202	Fire Fighting Equipment
203	Providing and fixing of FIRE EXTINGUISHER CO2 type as per IS:15683 complete with all accessories as per manufactures sepcification. ISI Mark Complete in all respect.4.5kg capacity
204	Providing and fixing of FIRE EXTINGUISHER ABC powder type (Stored pressure) as per IS:15683 complete with all accessories as per manufactures sepcification. ISI Mark Complete in all respect. 6kg Capacity
205	ELECTRICAL SERVICES
206	Providing Internal Electrical Installations:
207	POINT WIRING:
208	RECESSED PVC CONDUIT PIPE WIRING SYSTEM WITH MODULAR SWITCHES: Wiring in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in heavy gauge PVC conduit pipe 20mm/ 25mm dia. (ISI Marked) recessed in wall etc., complete with powder coated/anodized concealed metal boxes (1.6mm thick with Brass lugs) required for suitable number of modules (Modular accessories) for having Step type electronic fan regulators (two module) 100watts, bell push, 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10Amp. Switches, 16/20Amp. switches with indicator etc. and covered with Frame Plate etc., PVC connector (For Fan Box and Call Bell), Steel Hooks, Sheet metal fan box (1.6mm thick shape hexagonal), Circular junction Boxes (Four way PVC 1½\" deep for walls and CI 3\" deep for ceiling), bonding to earth with PVC insulated copper conductor single core FR cable (ISI marked) 1sq. mm, 1100volts grade (For 6Amp. wall socket & plug control point) and other petty material etc., including the cost of above material, cutting and filling up of chases (with finishing the surface):-
209	Wiring fan point (without fan box )
210	Wiring light point
211	Wiring call-bell point
212	Wiring6 Amp. wall socket point
213	Wiring6 Amp. Plug control comprising wall socket point
214	Wiring16/20 amp. power plug control point
215	REPLACEMENT OF WIRES, COVER FRAMES, MODULAR SWITCHES, CONCEALED METAL BOXES AND OTHER ACCESSORIES IN THE EXISTINGRECESSEDCONDUITPIPE WIRING SYSTEM (WITH MODULAR TYPE ACCESSORIES) Derived from 34.01:Replacement of PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in existing heavy gauge welded conduit pipe 20 mm/25 mm dia (1.6mm thick) ISI Marked, recessed in wall etc., complete with powder coated/anodized concealed metal boxes (1.6mm thick with Brass lugs) required for suitable number of modules (Modular accessories) for having Step type electronic fan regulators (two module) 100watts, bell push, 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10Amp. Switches, 16/20Amp. switches with indicator etc. and covered with FramePlateetc.,PVCconnector(ForFan BoxandCallBell),PVCBush,bondingto earth with PVC insulated copper conductor singlecore FR cable(ISI marked) 1sq. mm, 1100voltsgrade(For6Amp.wallsocket& plug control point)and other petty material etc. including the cost of above material, cuttingandfillingupofchases(with finishingthesurface):-(DerivedFromCSR 34.01)
216	Wiring light point
217	RECESSED COMPUTER SUPPLY TERMINAL POINTS (USED FOR HGW, PVC CONDUIT & HDPE PIPEWIRING SYSTEM WITH MODULAR ACCESSORIES):WiringComputersupply terminalpointsrecessedinwalletc.,completewithpowder coated/anodized concealedmetalboxesrequiredforsuitablenumberofmodules(Modularaccessories)forhaving 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10/16/20Amp.Switchesandblankingplateetc.,andcoveredwithFramePlateandotherpetty materialetc.includingthecostofabovematerial,cuttingandfillingupofchases(withfinishingthe surface):-
218	Wiring Computer terminalpoint having 3 Nos. 6Amp. 2/3universal socket (shuttered), 1No. 16 Amp. switch with indicator and 1No. blanking plate (Modular accessories).
219	RECESSED AIR CONDITIONERSUPPLY TERMINAL POINT (USED FOR HGW, PVC CONDUIT & HDPE PIPE WIRING SYSTEM WITH MODULAR ACCESSORIES):Wiring air conditioner supply terminal point recessed in wall etc., complete with powdercoated/anodizedconcealed metalboxesrequiredforsuitable numberofmodules(Modular accessories) for having 25Amp. combined/ universal Socket (shuttered) andmodular motor starter 25Amp. (2Module), covered with Frame Plate and otherpettymaterialetc.includingthe cost of above material, cutting and filling up of chases (with finishing the surface):-
220	Wiring AC supplyterminal pointhaving 1No.25Amp.universal Socket(shuttered) erected at AC height and 1No. Motor starter 25Amp. erected at switchboard height.
221	RECESSEDTV,TELEPHONE&NETWORKINGSOCKETSOUTLETPOINTS(USEDFORHGW, PVC CONDUIT & HDPE PIPE WIRING SYSTEM WITH MODULAR ACCESSORIES):Supplyand erection of TV socket, Telephone socket andNetworking socketpoints inpowder coated/anodizedconcealedmetalboxesrecessedinwallrequiredforsuitablenumberofmodules (Modular accessories) for having TV sockets, Telephone sockets RJ11 & Networking socket RJ45 (one module),coveredwithFramePlate andother petty materialetc.,including thecost ofabove material, cutting and filling up of chases (with finishing the surface):-
222	Wiring Telephone socket point RJ11 (one module)
223	Wiring Networking socket point RJ45 (one module)
224	SUPPLY AND ERECTION OF WIRING ACCESSORIES:Supply and erection of switches, sockets and other accessories (flush piano type/ modular accessories) in the existing bakelite/ modular cover frame including fixing & connections and petty material etc.:-
225	Ceiling Rose (Flush Piano type)
226	Call Bell 220/230 volts AC Ding Dong
227	COPPER WIRES & CONDUIT PIPE:
228	PVC INSULATED SINGLE CORE FR COPPER CONDUCTOR CABLE:Supply and erection of PVC insulated FR single core Unsheathed copper conductor cable (ISI marked) suitableupto1100voltsgradeconfirmtoIS:694/1990leftbareinpipeorcasingofsuitablesize complete in all respect as desired by the Engineer-in-charge:-
229	Overall size 1.5sq.mm (Un-sheathed)
230	Overall size 2.5sq.mm (Un-sheathed)
231	Overall size 4sq.mm (Un-sheathed)
232	Overall size 10 sq.mm (Un-sheathed)
233	PVC, HDPE PIPES & PVC FLEXIBLE PIPES:Supply & erection of PVC Conduit Pipes (ISI marked) as per IS9537:Part-III & HDPE pipes (ISI marked) asperIS:4984:1995forwiringpurposesincludingbends,junctionboxes,Steelhooks,M.S.saddle clamps and other petty materials etc., as per PWD General Specifications:-
234	Heavy gauge PVC conduit pipe 20mm dia. (ISI marked) Flushed
235	Heavy gauge PVC conduit pipe 25mm dia. (ISI marked) Flushed
236	Heavy gauge PVC conduit pipe 40mm dia. (ISI marked) Flushed
237	Supply and erection of PVC flexible pipe complete without compression glands, lockingarrangement, check-nuts as required:-
238	PVC flexible pipe 40mm dia.
239	HEAVY GUAGE WELDED CONDUIT PIPES:Supply&erectionofHeavyguageweldedconduitpipe(ISImarked)asperIS:9537:Part-IIforwiring purposes including bends, junction boxes, Steel hooks, GI saddle clamps and other petty materials etc., where necessary including painting as per PWD General Specifications:-
240	Supply & erection of 19/20mm dia. M.S. conduitpipe (1.6mm thick), white painted suspension rod for ceiling fan.
241	Copper Earthing
242	Earthingwith8SWG(4mmdia.)electrolyticcopperwirethimbled(1No.copperthimblewithsuitable size steelbolt, washers& double nut) with 30cm x 60cm x 2mm thickcopper plate (made cylindrical) burried below ground level in the hole of excavation having bore dia. 125mm and surrounded by salt & charcoal dust mixture (20 kg.) including fixing the copper wire run through 20mm dia. G.I. pipe (A-Class) recessed in wall and in floor etc., up to suitable Length in metre (including bore Length). G.I. pipe 20mm dia. (A-class) of suitable Length should be laid in the hole of excavation 1 feet below ground level and having GI Reducer 50mm x 20mm with PVC Cap (For pouring water) fixed on the top level of the pipe. 300mm x 300mm x 300mm deep haudi of First class bricks finished with 1:4 cement plaster and haudi covered with cast iron lid having size 300mm x 300mm (Heavy) around the hole of excavation:-
243	Earthingwith8SWG(4mmdia.)copperwirethimbledwith30cmx60cmx2mmthickcopperplate burried 10.50 metre (34.44 feet) below ground level (up to 14metre in Length) with G.I. pipe 20mm dia. (A-class), 9metre long
244	Fixing additional Length of earthing with 8 S.W.G. (4mm dia.) copper wire in G.I. pipe with sockets, elbows, steel hooks and GI saddle clamps including painting etc.:-
245	MCB\"S & MCB DISTRIBUTION BOARDS:
246	MINIATURE CIRCUIT BREAKERS:Supply and erection of Miniature Circuit Breaker MCB\"s for circuit protection against overload and short circuit current fault suitable for 240/ 415 volts 50cycles AC supply with breaking capacity of 10kA, Curve CandlowwattlossesasperIS/IEC60898-1,energylimitationclass-3,truecontactindication,label holderfacilityintheexistingMCBdistributionboardasperPWDGeneralSpecificationsincluding connections with suitable size of thimbles/lugs:-
247	MCB Single Pole 6-32amp. (10kA, Curve-C)
248	MCB Double Pole 40amp. (10kA, Curve-C)
249	MCB Four Pole 50, 63amp. (10kA, Curve-C)
250	SHEET METAL DOUBLE DOOR DISTRIBUTION BOARD FOR MCB/ RCBO/ RCCB\"s:Supply and erection of sheet metal DoubleDoorDistributionBoardsIP 43- IK09 metal door (dust protected) as per IS 8623-1&3, IEC 61439-1&3 suitable for flushmountingwithfullyinsulated copper busbars, shrouded neutral bars, earth bars, cement spill protector, color- codedinterconnectingwireset,cable ties, blanking plates and circuit identifications label and of required no. of ways for mountingminiature circuit breakers/ RCBO\"s/ RCCB\"s in the distributionboard(ForSP&N distribution board with provision DP MCB\"s/ RCCB\"s/ RCBO\"s as incomer and SP MCB\"s as outgoings and for TP&N horizontal distribution board with provision TPN/ FP MCB\"s/ RCCB\"s/ RCBO\"s as incomer and SP MCB\"s as outgoings) as per PWD General specificationsincludingconnections with suitable sizeofthimbles and bonding to existing earth etc:-
251	SP&NDoubleDoorDistributionBoard12 way each
252	TP&NHorizontal DoubleDoorDistribution Board 4 way each
253	XLPEINSULATED UN-ARMOURED CABLES (LOOSE):-Supply,layinganderectionofaluminiumconductorXLPEinsulatedPVCsheathedUn-armouredand served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid loose in the existing trench or pipe as per PWD General Specifications:-
254	Overall size 16sq.mm (4 Core) Un-armoured (Loose) For PSPCL supply
255	DOUBLE WALLED CORRUGATED (DWC) HDPE PIPES:Supply and erection of Double Walled Corrugated (DWC) HDPE pipe to be laid 1mtr. below ground level including excavation placing the pipe in position and back filling with excavated soil etc. of the required size:-
256	Double walled corrugated (DWC) HDPE pipe 63/51 mm (outer/ inner dia.)
257	MCCB\"s (MOULDED CASE CIRCUIT BREAKER):SupplyanderectionofMouldedCaseCircuitBreaker(PanelmountingCubicaltype)intheexisting CubicalPanel(confirmtoIEC:60947-2)havingIcs=100%Icu,100%neutralwithspreaderlinksand relevantPWDgeneralspecificationscompletewithG.I.Bolts,Nuts&Connectiononbothsidesof MCCB with suitable size of thimbles etc:-
258	MCCB Four Pole 40/63/80/100amp., 415volts, =25kA Fixed Magnetic and Adjustable Thermal Setting
259	MS SHEET ENCLOSURE FOR MCCB\"s:Supply & Erection of indoor type MCCB enclosure of suitable size having provision for MCCB with extended rotary handle.TheEnclosureshall bemade from 14/16 SWG CRCA sheet, confirming to IS 8623/1977-82. The door should be double folded without edge and the gasket should be ‘S’ type puffed neutral rubber gasket for long life. The hinges of the door should be bolted type with double hole arrangement. The Enclosure door lock should be quick openable type spring loaded. There should not be any special tool or key to open the lock. The Enclosure will be wall mounting type having provision for cable entry from bottom/topwith cable glands etc. The sheet metal is sprayed with corrosion resistant etch primer. The finishing treatment shall be applicable with air drying paint (7/9 tank Powder coated process should present in company pemises) after necessary putty work:-
260	MSSheetEnclosurehavingprovisionfor MCCB 40-160Amp.with extended rotary handle (Approx.Size 500mmx300mmx 200mm)
261	SHEET METAL IRON CLAD CHANGEOVER SWITCHES:Supply and erection of sheet metal Iron Clad Changeover Switch on existing surface with G.I. bolts & nuts/ragboltsandnutsetc.,accordingtothesizeofholesinthebodyoftheswitchincluding connectionswithsuitablesizeofthimblesandbondingtotheexistingearthasperPWDGeneral Specifications:-
262	ICFourPole Changeover Switch 63amp., 415volts
263	AUTOMATIC VOLTAGE STABLIZER:
264	SupplyanderectionofSinglephasecopperwoundAutomaticvoltagestablizerofsuitable capacity electronically controlled circuit with input voltage 140-260 volts single phase AC supply andoutputvoltage220±5%voltssinglephaseACsupplyhavingmainsiliconcorecopper wound step up transformerwith suitable nos. of turns on primary side and secondary side the transformer should be fully insulated inside the MS sheet boxof suitable size. There should be powercontrolrelayandsinglepoleMCB(C-curve,10kA)ofsuitablecapacitycompletewith internal copper wiring along with amp. meter and volt meter, high voltage cut off 280 volt input (240 volt output) and 90 volt maximum boost and overloading protection to be provided:-
265	Automatic Voltage Stablizer 4 KVA
266	Automatic Voltage Stablizer 5 KVA
267	LED\"S FIXTURES & FANS:
268	SupplyanderectionofLEDbatten20wattLED(includingLEDdriver)with Highqualityextruded aluminiumwith efficacy ofLEDfixture minimum100 lumensper watt and operatingvoltage between 140to270volt,inputACfrequency50Hz±3%complete alongwitherectionofthesamewith connections, testing etc. complete in all respects as approved and desired by the Engineer-in-charge at site.ThecertificationandSpecificationsoftheLEDFitting\"sshouldbe asapprovedbyO/oAdvisor (Technical), Govt of Punjab vide Letter no.AT/2021/GL/1410-1422 Dated 06/05/2021.
269	Supply and erection of LED batten 40watt LED (including LED driver) withHigh quality extruded aluminium with efficacy of LED fixture operating voltage between 140 to 270 volt completealong with erection of the same with connections, testing etc. complete in all respects as approved and desired by the Engineer-in-charge at site.LED Fitting as per Specifications approved by Hon. Tech. Advisor to CM Punjab vide LetterION No:- AT/2021/GL/1410-1422 Dated:- 06.05.2021.
270	Supply and erection of Slim Surface mounted, Round downlighter 18 watt with Pressure die cast aluminium housing & polycarbonate diffuser with surge protection 10KV and efficacy of LED fixture minimum 100 lumens per watt complete in all respects as approved and desired by the Engineer in-charge at site .
271	SupplyanderectionofSlimRecessedmounted,Rounddownlighter18wattwithPressurediecast aluminium housing & polycarbonate diffuser and efficacy of LED fixture minimum 100 lumens per watt complete in all respects as approved and desired by the Engineer in-charge at site. The certification and Specifications of the LED Fitting\"s should beas approved by O/o Advisor (Technical), Govt of Punjab vide Letter no.AT/2021/GL/1410-1422 Dated 06/05/2021.
272	Supply and erection of Recessed mounted 36watt LED panel(including LED driver) with CRCA sheet having efficacy of LED fixture minimum100 lumens per wattand operating voltage between 140 to 270 volt,inputACfrequency50Hz±3%complete alongwitherectionofthesamewithconnections, testingetc.completeinallrespectsasapprovedanddesiredbytheEngineer-in-chargeatsite.The certification and Specifications of the LED Fitting\"s should beas approved by O/o Advisor (Technical), Govt of Punjab vide Letter no.AT/2021/GL/1410-1422 Dated 06/05/2021.
273	Supply and erection of LED Street Light 45 watt (including LED driver) with pressure die cast aluminium housingwithcontrolgear( IP66protection),THD<10%,CRIminimum70, HighpowerLEDwith mandatory secondary lenses, toughened glass fitting, 4 KV SPD within driver and 10KV external SPD, efficacy of LED fixture minimum 120 lumens per watt, complete in all respects as approved and desired bytheEngineerin-chargeatsite.LEDFittingsasperspecificationsapprovedbyHon\"bleTechnical Advisor to CM Punjab vide letter No. AT-2021/GL 1410-1422 Dated 06/05/2021
274	Supply and erection of Ceiling Fan 1200mm (48\") with double ball bearing including flexible wire & petty materialetc.forconnectionsandtestingcompleteinallrespectsasapprovedanddesiredbythe Engineer in-charge at site. The fan should conform to Technical Specifications attached.
275	Supply and erectionof VentileAir Fan225/230mm withaluminium louvershutter longerlife including flexible wire & petty material etc. for connections and testing complete in all respect asapproved and desired by the Engineer in-charges at site. The fan should conform to Technical Specifications attached.
276	SITC of Wall Fan Size 400MM as desired by EIC. The fan should conform to Technical Specificationsattached.
277	Supply & Installation of 12V. 150AH tubular battery including connection & testing charges etc. Complete in all respect as per entire satisfaction of the Engineer In Charge.
278	Supply & Installation of Stand for Inverter & 2 No. Batteries including connection & testing charges etc. Complete in all respect as per entire satisfaction of the Engineer In Charge.
279	Supply & Installation of 2KVA Sinewave Inverter including connection & testing charges etc. Complete in all respect as per entire satisfaction of the Engineer In Charge.
280	Providing 2Way Phone, Patient Token System,Local Area Networking :
281	Supply Installation Testing and Commissioningof10 port 10/100 PoE switch, 8*10/100 PoE port + 2 10/100uplink,powerbudget120W,IEEE802.3af/at extendedrange250mtrcomplete alongwith erection of the same with connections, testing etc. complete in all respects as approved and desired bythe Engineer-in-charge at site.
282	Supply, installation, testing &commissioning ofCategory 6 UTP, 4Pair Thiscable wellexceedsthe requirements of TIA/EIA-568-C.2 and IEC/ISO 11801. Construction: 4 twisted pairs separated by cross separator,4channel,polymerspine/fullseparator.Halfshallnotbeaccepted.Cableshouldbe Armoured.Operatesatbandwidthof250MHz,ConductorSolid BareElectronicGradeCopper. Inner jacketshouldbePVCandoutershouldbePE,suitablefordirectburial.Insulation:Polyethylene, Attenuation (< 36 db/100m), Pair – to – pair and PS NEXT, ELFEXT and PSELFEXT, Return Loss, ACR and PS ACR., Nominal Outer Diameter of Cable should be 9.70 mm and Conductor Diameter 0.56 mm (23 AWG), Cable should support operating Temperature from -20° to +60°C, Cable should come with printed sequential Length Counter on each meter, Cable support Conductor Resistance 93.5 OHMS/1000MTR@20 Degree, Mutual Capacitance of cable should be < 5.6nF/100m, Max Resistance Unbalanceofcableshouldbe5%Max,CapacitanceUnbalanceofcableshouldmax330pF/100m, CablesupportDelaySkew:<45nS,OperatingVoltage:72VandNVP:69%,ShallSupportsGigabit Ethernet (1000 base-T) standard and Operates at bandwidth of 250MHz complete along with erection of thesamewithconnections,testingetc.completeinallrespectsasapprovedanddesiredbytheEngineer-in-charge at site.
283	Supply,installation,testing&commissioningof 1KVAUPSwithInputpowerfactor-0.99,Output powerfactor-0.8,OVCDinbuilt,DCV24v,Efficiency:Above90%..completeinallrespectsas approved and desired by the Engineer-in-charge at site
284	S/I/T/C of intercom facility 1+1 Basic Plan Phone Ringer volume control switch Tone/ Pulse Switchable Redial Mute Flash Pause Intercom facility Call T, Holding the line / Music on Hold during call transfer LineuseLEDIndication,Secrecyduringconversationbetweenbothphones,includingconnectingcables
285	S/I/T/C of Token Calling Display System having screen size 4 inches, Voice calling/ Bell System, complete key pad Etc, calling display up to 60 meter cable (5 meter length included), serial communication design, Text Color Red Display Shape Rectangle,Power 5 W,Sound Type Mono Display Technology 7 Segment Voltage 220-240 V AC Suitable for Clinic, Hospital,Cash counter etc, Warranty 1 Year,220 VAC Operating Voltage Character Capacity 3 Character, Power Consumption
286	Supply and erection of Wall Mounted 6U Rack with power point and fan.
287	Providing Double Door Refrigerator,Water Dispenser and Split air conditioner:
288	Supply,Installation and Comissioning of Frost Free Double Door Refrigerator capacity 250 Ltr - 265 Ltr completeinallrespect.TheRefrigeratorshoudalsoconformtotechnicalspecificationsattached herewith.
289	SupplyInstalationTestingandcommisssioningoffloormountedHot,coldandnormalwater 3Tap dispenser.Completeinallrespectasrequired.TheWaterDispensershouldalsoconformto thetechnical Specication Attached herewith
290	Supply, Installation and Comissioning of BEE 3 STAR/4STAR2.0 Ton split air conditioner with 100% coper coil material( evaporator and condensor) complete in all respect . The Air Conditioner should alsoconform tothe technical Specication Attached herewith
291	Supply, Installation and Comissioning of BEE 3 STAR1.5 Ton split air conditioner with 100% coper coil material( evaporator and condensor) complete in all respect . The Air Conditioner should also conformtothe technical Specication Attached herewith

Need a Bussiness Loan? Apply Now!
Buy Digital Signature
Bidding Support

Also Visit

Tenders

Punjab Tenders

Construction Tenders

Civil Construction Tenders

Civil Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Conversion Of Existing Sad At Village Maur Kalan Into Mohalla Clinic District Bathinda., Bathinda-Punjab

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Conversion Of Existing Sad At Village Maur Kalan Into Mohalla Clinic District Bathinda., Bathinda-Punjab

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us