Sales : +91-777 804 8217
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 17-12-2022 | BOQ | Other | 23-12-2022 |
| Sl. No. | Item Description |
| 1 | Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel,stoney earth and earth mixed with small size boulders SS.20B and Sand, silt or other loose soil, wet sand,or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrockrequiring blasting inclusive of shoring shuttering and baling out water and cleaning and levelling the site etc.,complete Earthwork Excavation |
| 2 | FOUNDATION |
| 3 | PLINTH BEAM |
| 4 | Supplying and filling in foundation and basement withfilling M-sand in layers of not more than 15cm.thick well rammed watered and compacted etc., completecomplying with standard specification. DATA |
| 5 | Refilling with excavated earth in layers of 30 cm watered well rammed and consolidatred conforming to standard specification including labour charges as directed by Engineer in Charge |
| 6 | Supplying and providing Anti termite pre constructiontreatment using aldrin or dealdrin or heptochlor as perrelavent IS 6313 (part II) code including cost of allmaterials, labour, hore charges for T&P etc complete. |
| 7 | Plain Cement Concrete 1:4:8 (one cement four fineaggregates and eight coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification |
| 8 | Supplying and filling the basement with Good Earth filling in layers of not more than 15cm thick well rammed watered and compacted - etc., complete complying with standard specification |
| 9 | Plain Cement Concrete 1:2:4 (one cement, two fineaggregates and four coarse aggregates) using 20mmsize ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges etc., complete as per standardspecification |
| 10 | Supplying and erecting steel centering includingnecessary supports for plane surfaces for ReinforcedCement Concrete works such as column footings,column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shallbe given after the concrete is laid) |
| 11 | Supplying and erecting centering for sides and soffitsincluding necessary supports and strutting upto 3.29 Mheight for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steelangle of size 25mm x 25mm x 3 mm for boarding laidover silver oak joists of size 10cm x 6.50 cm spaced atabote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid) |
| 12 | For plane surfaces such as RCC floor slab, roof slab,beams, lintels, bed blocks, landing slab, waist slab,portico slabs and beams, etc |
| 13 | For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc. |
| 14 | M-25 CONCRETE - Providing and laying in position,standarised design mix M-25 Grade using 20mm anddown graded hard broken granite stone jelly for all RCC items of works with minimum cement content of350Kg/m3 and maximum water cement ratio of 0.55,including admixture(plasticiser/super plasticiser) inrecommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.70 cu.m.)940.50Kg of 20mm machine crushed stone jelly and with about (2.80 cu.m.)462.00Kg of 10-12mm machine crushed jelly and with about (4.25 cu.m.)701.25Kg of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor/roof slabs wherever neccessary without clambing extra, etc. complete complying with standard specification and as directed by the departmental officers. the coarse and fine aggregates to be used should comply with the requierments of IS 383-2016. (No separate payment will be made by the department for the exces usage of materials as per design mix.) (SI No 81) |
| 15 | Foundation |
| 16 | Ground Floor |
| 17 | Providing and laying in position Standardised Concrete Mix M-25 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 325Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of sand, but excluding cost ofreinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - The Coarse and Fine aggregates to be used should comply with the requiremnents of IS staandards. (No separate payment will be made by the Department for the excess usage of materials) |
| 18 | Suppling and fabricating and placing in position MS (or) R.T.S. bar for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors. |
| 19 | Brick work in CM 1:5 (one cement & five sand) using IIclass ground moulded bricks of size 9\"X43/8\"X 2 3/4\"including finishing, curing, etc., complete complying with standard specification. |
| 20 | Ground Floor |
| 21 | Brick Partition Walls using II class ground mouldedchamber bricks of size 9\"X43/8\"X 23/4\" in C.M 1:3using hoop iron reinforcement,if found necessarystandard specification including finishing, curing,etc.,complete complying with standard specification - 10 sqm |
| 22 | Ground Floor |
| 23 | Plastering with cement mortar 1:3,10 mm ,thick in allfloors including cost and conveyance of all materilas tosite and labour charges etc,complete as per standardspecifications (S.I.306) |
| 24 | Plastering with cement mortar (1:5) 12mm ,thick in allfloors including cost and conveyance of all materilas tosite and labour charges etc,complete as per standardspecifications (S.I.306) |
| 25 | Plastering with cement mortar (1:4) 20mm thick in allfloors including cost and conveyance of all materials tosite and labour charges etc, complete complying withstandard specifications (S.I.309 |
| 26 | Providing Laying the Flooring with Anti skid colouredceramic tiles of sizes 305mm X305mm X 6mm size ofapproved make and quality and colour l Set in cementmortar 1:3 (one cement ,three sand) over 20 mm baselayer plastering and pointing with white cement neatly as directed. |
| 27 | Dadooing walls with Glazed tiles of sizes 305mmX200mm X 6mm size of approved make and quality and colour l Set in cement mortar 1:2 (one cement ,two sand) over 10 mm base layer plastering and pointing with white cement neatly as directed. |
| 28 | Painting 2 coats with approved cement paint overcement plastered wall surface, ceiling and other newsurface and including cleaning, preparing the surfaceand curing etc., complete. |
| 29 | Painting two coats with Ready Mixed Enamel Paint over the new iron works of approved quality and colourwithout priming coat including the cost all materialsetc.,complete, in all floors. |
| 30 | Paving the floor with design Rajasthan kotta tiles (colour and shade as directed) of size 610 mm x 610mm x 20mm in all floors over a base layer of cement mortar 1:3 (one cement and three sand ) 20mm thick laid in-situ and pointed with same coloured cement etc, complete asper standard specification |
| 31 | Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding,grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification. |
| 32 | Supplying, fabricating, erecting structural steel work forroofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification |
| 33 | Supplying & fixing door shutters for Mediun DensityFiber Board of exterior grade 35 mm thick,single leafconforming to IS:12406/1989 with 35x12 mmT.W.Lipping on all edges with necessary adhesives and CP screws complying with standard specifications. The rate is inclusive of threee coats of best quality varnish but excluding cost of furniture fittings.such as 300 mm tower bolt 2nos,200mm towerbolt I no. 300mm Aldrop 1 No. Alu handle ornamental type 2 Nos,and 1 No. Doorstopper etc complete. |
| 34 | Supplying and Erecting Pull and Push Type RollingShutter with ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc ROLLINGSHUTTERS (WITH ISI MONOGRAM) ManuallyOperated (up to 8 sqm. Area |
| 35 | UPVC VentilatorSpecification: Supplying and fixing UPVC (Un Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work PWD SOR Pg. No. 66 |
| 36 | Providing and fixing Bitumen Pad for Expansion joint in between pavement slabs to 12mm thick and fixed as shown in the drawing including cost and conveyence of expansion joints including shalimar pad and joint sealent etc, complete as per standard specification |
| 37 | Finishing the top of roof with one course of machinepressed tiles of size 200 mm x 200 mm x 20 mm ofapproved quality in Cement Mortar 1:3 (One Cement add three sand) 12 mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete |
| 38 | Weathering Course with Concrete Broken Brick(S.I.No.278) & ( P & D) Data 54.Jelly 20mm gauge inpure slaked lime (no sand to be added) over roofslab,the proportion of brick jelly to lime being \"32 to 12.5 well beated with wooden beaters for giving required slope and thickness as directed by the departmental officers etc., complete.-10 cum |
| 39 | Fabricating supplying and fixing of pre paintedgalvanized iron sheets with the following specification.The materials should be of PPGI tile profile with a redcolour or any other approved design 0.47 mm thick 24guage having width 1050 mm. The sheet should beG.I.base pre painted hot dipped galvanized iron sheetand to be fixed with shelf tapping screws,plasticwasher.The washer and screws to be fixed by usingminute power machine drilled with out damaging thesheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers |
| 40 | Designing the Semi Unitised Structural Glazing System with open groove joint as per design intent, preparation of shop drawings for approval, supply, fabricate, erect as per approved shop drawings at all floor levels and allfloor heights including conductingfield test as per the test criteria set out in the particularspecification (Metholodgy should be got approved by the Dept. Officials.) Design the framing system (i.e. male & Female frame) to support vision panels, spandrel panels either with glass or aluminium composite panel, openable, window panels on a continuous framing supported between floors. Also design the split framing unutilized glazing system in case of strip or punched windows with vision panel proposed with either insulated / Monolithic glass, groove width in the system both in horizontal and vertical shall not be more than 20mm. Glazing ofpanel shall be done only at factory at the controlledatmosphere |
| 41 | Supplying and laying rubberised inter locking paver block m40 grade providing and laying of 63mm thick high strength type confirming IS 15658-2006 of rubberised inter locking paver block in size of minimum compressive strength of 40N/mm2 in uniform shape of approved make to be laid in flurring bone pattern with stone dust cushion below the uniform shap of approved non skitting surface in the top and the rate including levelling the base preparation of pavers as sub base, stone dust cushion 150mm thick laying out of pavement cut the pieces to fix the edge vibring the pavers,sweeping tranporting loading unloading of laying paver block as per standard specification, |
| 42 | Providing and laying, spreading and compacting graded stone aggregate to Wet mix macadam (WMM)specification including premixing the material with water at OMC in mechanical mix plant carriage to mixed material by tipper to site laying in uniform layers with paver in sub base / base course on well preparedsurface and compacting with vibratory roller to achive the desired density complete as per clasue 406 of MORTH specifications. |
| 43 | Manufacturing, Supplying and Fixing of Stainless SteelHand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thickwelded to the railing. The supports will be grouted intothe wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete (PWD SOR P.NO :57) |
| 44 | Supply and fixing of stored pressure ABC (MonoAmmonium Phospate) Powder Type FireExtinguisher of 6 kg. capacity as per IS:15683 withpressure gauge, discharge hose & control nozzle,wall mounting bracket, safety clip etc., includingconveyance, all incidental charges, neccessaryscaffolding and re-doing the dismantled portions toits original condition wherever found neccessary etc, complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENTPWD SOR Page No. 97 Sl. No.382 |
| 45 | First Aid Box complete with all First Aid MedicinesPWD SOR Page 142. Sl.No.8c |
| 46 | 4 Nos of Fire Buckets made out of 40x40x6mm MSAngle PWD SOR Page 142. Sl.No.8e |
| 47 | Supply and fixing of Water CO2 Stored PressureType 9 litres capacity Fire Extinguisher as per newIS 15683 complete with control valve, gun metalcap, pressure gauge, operation sticker, dischargehose, wall mounting bracket, safety clip, etc., asdirected by the Departmental Officers.PWD SOR Page No. 81. Sl.No.330 |
| 48 | Providing rain water harvesting using 3 nos.of RCC well rings of 90cm inner dia (clear) with 5cm wall thickness made out of cement concrete 1:2:4 using 20mm hard broken jelly to a height of 30cm each supplying and fabricating 16 nos. of 6mm dia MS rod vertically and 3 nos. of 6mm dia MS rod circumferentially tied together with 18 guage binding wire for well rings includingnecessary earth work excavation 1m dia to a depth of1m, supplying and filling 40mm HBG inside the erected well ring to a depth of 90cm, and top covered with RCC circular perforated cover slab of 1m dia and 5cm thick which inclusive of cost and fabrication of 6mm M.S reinforcement at 15 cm spacings on both directions and one 6mm M.S rod ties at the edge of the slab circumferentially including cost of moulding, curing, finishing and well placing in position and disposing off excavated earth with all initial leads and lifts in places as shown by the Departmneal officers etc., complete in all respects. |
| 49 | Supply and delivery of Electric Monoset centrifugal pumpconforming to IS 9079:2002 as amended from time to time, with CI FG 200 Casing , hydraulically and dynamically balanced Bronze grade LTB-2 impeller, impeller ring and casing ring, stainless steel shaft capable of discharging required quantity of water against a total head noted below due to all causes. Pump shall of BEE 3 Star Rated and capable of discharging the specified quantity at the head notedat the minimum NPSHA at site conditions. The shut off head shall be atleast 25% over and above the head at duty point. The pump shall be suitable for operation in AC three phase , 415 V+/- 10% , 50 Hz +/- 5%. Squirrel cage induction motor for continuous operation. The speed of the Pump and Motor shall be not less than 2700 to 2900 RPM respectively. 500X20LPM(TWAD SOR P.NO:95) |
| 50 | Investigation charges for Geophysical survery finding of yeild to the point drilling of Borewell for all etc., complete |
| 51 | Drilling of 4 1/2\" diameter borewell by using Calyx Drillincluding transporting charges and insertion of casingpipes (excluding cost of casing pipe) FOR PLAIN AREA (TWAD SOR P.NO :280) |
| 52 | Supply and delivery of clear water vertical wet typesubmersible pump suitable for 150mm dia borewellconforming to IS 8034/2002 as amended thereafter and BEE 3 Star Rated capable of discharging noted LPM against head of water column due to all causes. The pump shall be with stainless steel shaft and dynamically balanced bronze or Cast SS impeller, brass screws and CI FG 200 grade pump bowl/diffuser with ISI mark. The pump shall be directly coupled to a continuos rated two pole suitable wet type vertical squirrel cage induction motor as per IS 9283 /1995 and as amended there after, suitable for operation in AC three phase 415 V+/- 10 %, 50 HZ +/- 5 % (50 Lpm X 60 m )(TWAD SOR P.NO : 98) |
| 53 | Labour Charges for the erection of Submersible pumpset in borewell including fixing and jointing submersible cable with proper clamps upto the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps, and erection of panel board consisting of TPICN swtiches starter voltmetre, Ammeter, three point (indicating) lamps capacitor single phasing preventor and laying and jointing the cable and twin earthing for etc., Complete and testing the pumpset and trail run for 10 days. (TWAD SOR P.NO : 287) |
| 54 | Supply and Delivery of 150mmdia PVC casing Pipesincluding cost and conveyance of materials and labourcharges etc. complete as per standard. Specifications |
| 55 | 150 mm dia pvc casing pipe (twad sor p.no :119) |
| 56 | Supply and delivery of 3 phase panel board D.O.L delta with two level guard and auto start to suitable for 5 HP submersible pumpset etc. complete (TWD SOR P.NO :110) |
| 57 | Supplying delivery of G.I and PVC Pipes and specialsof approved quality and best varity of B Class pipeincluding cost convayence of materials to work site etc., complete. |
| 58 | 50mm Dia G.I Pipe (PWD SOR P.NO 45) |
| 59 | 50mm Dia G.I Coupling (PWD SOR P.NO 47) |
| 60 | 50mm Dia G.I Elbow (PWD SOR P.NO 46) |
| 61 | 50mm Dia G.I Union (PWD SOR P.NO 46) |
| 62 | 50mm dia Gun Metal Gate Valve(PWD SOR P.NO 48) |
| 63 | Borewell M.S.Clamp set (TWAD SOR P.NO :44) |
| 64 | Borewell 8 Module Cover Plate (twad sor p.no : 182) |
| 65 | 40mm Dia PVC pipe (PWD SOR P.NO 99) |
| 66 | 40 mm Dia PVC Coupling (PWD SOR P.NO 99) |
| 67 | 40 mm Dia PVC Elbow (PWD SOR P.NO 100) |
| 68 | 40 mm Dia PVC Bend (PWD SOR P.NO 100) |
| 69 | 40 mm Dia PVC Reducer 50 x 40 mm (PWD SOR P.NO 100) |
| 70 | supply and delivery of PVC inclused and sheated 4 core 16 sq.mm. PVC Armoured UG Cable (pwd sor p.no :125) |
| 71 | supply and delivery of PVC inclused and sheated 4 Providing & fixing PVC RAIN WATER DOWN FALLPIPE of the following dia with necessary T.W.ClampsPlugs, Shoes, Bemds, other clamps, screws nails etc., complete complying with standard specification. The rate is inclusive of cost of removable iron gratings of appropriate size. The size of Teak Wood plugs used is 150X25mm in front & 200x75mm in rear (wall side) with a depth of 110mm. The pipe is to be fixed by means of \"U\" clamps at the centre of pipes to be fixed.110mm dia PVC Pipe [4 Kg/SqCm](D) |
| 72 | Supplying and fixing of 1000 litters capacity PVC tank of approved quality including cost of all materials like tank fittings, lead .lift, errection etc complete. PWD SOR PGNO:91 |
| 73 | Supplying and fixing in position first quality and approved variety of Gun Metal Gate Valve (Heavy type ) with I.S.I.mark of the following sizes including cost of Shellacthread etc,.including labour for cutting and threading of G.I.Pipes etc.,complete complying with standard specifications for both internal and external water Supply arrangements. (D) |
| 74 | 25mm Gun Metal Valve |
| 75 | 32mm Gun Metal Valve |
| 76 | Suppling and fixing in position 15mm.diameter brass /C.P screw down tap / pillar tap (heavy duty) of approved make conforming to I.S.specifications and quality including cost of shellac, thread etc.complying with standard specifications and including cutting andthreading wherever necessary (D) |
| 77 | SD Tap |
| 78 | Pillar Tap |
| 79 | P.V.C. Pipes (10Kg/SqCm) Supplying laying and jointing P.V.C pipes (10Kg/SqCm) of approved quality and best variety conforming to I.S.S & with I.S.I mark, of the following sizes including cutting , Fixing to PVC specials using Adhesive but excluding cost of such specials and fixing to wall with necessary teak - Wood Plugs,PVC Clamps and screws,making holes on the wall or drilling holes in roof and making good the dismantled portions to original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges.(D) |
| 80 | 25mm dia Pipe |
| 81 | 32mm dia Pipe |
| 82 | Supplying PVC Specials (with working pressure 10 kg. / sq.cm.) in water supply arrangements (both in internal and external water supply arrangements PWD SOR PG.NO:99 SI.NO:367 |
| 83 | Coupler |
| 84 | 25mm dia Pipe |
| 85 | 32mm dia Pipe |
| 86 | Elbow |
| 87 | 25mm dia Pipe |
| 88 | 32mm dia Pipe |
| 89 | BEND |
| 90 | 25mm dia Pipe |
| 91 | 32mm dia Pipe |
| 92 | Tee |
| 93 | 25mm dia Pipe |
| 94 | 32mm dia Pipe |
| 95 | End cap |
| 96 | 25mm dia Pipe |
| 97 | 32mm dia Pipe |
| 98 | Reducer |
| 99 | 25mm dia Pipe |
| 100 | 32mm dia Pipe |
| 101 | Reducer Tee |
| 102 | 25mm dia Pipe |
| 103 | 32mm dia Pipe |
| 104 | Reducer Elbow |
| 105 | 25mm dia Pipe |
| 106 | 32mm dia Pipe |
| 107 | Jet Nipple |
| 108 | 25mm dia Pipe |
| 109 | 32mm dia Pipe |
| 110 | Supplying and fixing in position PVC specials of thefollowing dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks,dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the ExecutiveEngineer before use on works).(D) |
| 111 | PVC Elbow |
| 112 | 110mm Dia |
| 113 | PVC Elbow With Door |
| 114 | 110mm Dia |
| 115 | PVC Tee |
| 116 | 110mm Dia |
| 117 | PVC Tee With Single Door |
| 118 | 110mm Dia |
| 119 | Supplying and fixing in position best quality approvedmake white glazed earthenware wash hand basin of size 550 X 400 mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated piller tape,32 mm diametre C.P. Waste union, 32 mm diametre P.V.C. waste pipe with rubber plug and chain, 15mm diametre G.M.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications (D |
| 120 | Supplying and fixing in position Indian water closet ofsize 580 X 440mm, white glazed earthen ware ofapproved quality with \"P\" trap or \"S\" trap confirming toIS:2556 - Part XII with sand cushion and formingflooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 ( one part of lime, two parts of sand and five parts of brick jelly) 100mm thick andfinishing the top to required slope and including givingnecessary connection to cast iron soil pipes/ PVC pipes by dismandling brick masonry, reinforced cement concrete roof/floor slab and making good the disturbed portion to original condition without leakage etc., complete complying with standard specifications and as directed by the departmental officers. |
| 121 | S/F in position of Indian Make White/Colour glazedearthen ware lipped mouth Flat Back Urinal of bestapproved quality with G.I.Pipe connection to suitablelength,32mm bell mouthed P.V.C connection ,15mm dia G.M.Wheel valve,fixing the urinal to the wall in position with necessary T.W.plugs ,clamps,screws, shellac etc.,including dismantling masonry if necessary and redoing the same to original condition ,fixing the 15mm dia. G.I.pipe connection and wheel valve ,painting the pipe with two coats of approved paint over one coat of primer and checked without any leakage complete, complying with standard specifications. - White Colour |
| 122 | Supplying and erecting in position of 250 liters capacityIndustrial Model Reverse Osmosis Water-cum-Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 - 1 No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20” Filter with Housing - 1 No., Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System inposition and intact(250lts)(PWD SOR PG NO 77 |
| 123 | Supplying and fixing in position White Glazed European Water Closet of best quality and approved make with 100mm \"P\" os \"S\"\" trap with Double flapped rigit P.V.C. seat cover with C.P. brass hinges with 12.5 litres PVC Low Level Flushing Tank with all internal fittings etc., complete complying with standard spoecifications,labor inclusive of fixing lowlevel flushing tank. (D) |
| 124 | White EWC |
| 125 | Supply and fixing of PVC. Nahini / Floor Trap withstainless Steel Gratings- 100 mm x 75 mm including all charges etc, complete as per standard specification.(D) |
| 126 | Supply and fixng of TNEB meter board suitable for 3phase 100A service connection made up of suitableangle iron frame work of size 2 feet x 1-1/2 feet usingangle iron of size 1-1/2\" x 1-1/2\" x 1/4\" rigidly fixed onwall covered with hylem sheet of size 2 feet x 1-1/2 feetof 12mm thickness with necessary bolts and nutssupports and supply and fixing of 3 Nos. 100A fuse units(500V), 1 No. neutral link, copper earth flat of size 1\" x 1/4\" with inter connection of EB meter to fuse units by 16 Sq.mm PVC insulated copper wire with earth connection complet (SD 130) |
| 127 | Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SCunsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with TW switch box and 5A FT switch with painting of suitable colour for open PVC light point / fan point (for electronic regulator) (4 points per coil) (SD 17) |
| 128 | Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SCunsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with suitable TW box in flush with wall to house the control switch regulator and covered with 3mm thick hylem sheet with painting of suitable colour with continuous earth connection of 14 SWG TC wire for open PVC fan point (for rheostatic type fan regulator)SD (34) |
| 129 | Supply and fixing of 6A 3 Pin flush type wall socket with6A flush type switch concealed in suitable MS Box inflush with wall and covered with 3 mm thick hylemsheet(SD 138) |
| 130 | Supply and fixing of 5A 3 pin and 2 pin combined flushtype wall socket with 5A flush type switch concealed insuitable MS box in flush with wall and concealed with3mm thick hylem sheet SD (135) |
| 131 | Supply and run of 2 of No.8 SWG GI wire for guardingwith cradle with No.8 SWG GI wire at the equal intervalof 1.5 metre SD (75 |
| 132 | Supplying and fixing MCB isolator 32A TP with earthconnection (Legrand (MDS/Hager (L & T make) (PWDSOR P.NO :134) |
| 133 | Earthing as per the ISI specification with an earthelectrode of 2.10 metre Class \"B\" GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry (SD233) Body Earth |
| 134 | Supply and fixing of 18W 4 Feet LED Fitting with LEDLight fitting complete with TW round blocks on ceilingwith PVC unsheathed Copper leads from terminals to the fitting (SOR Page No.114) |
| 135 | Supply and fixing of 18W LED 3000K Square typeresessed fiiitng (Philips/Havells) complete with T.Wround blocks on wall or ceiling with flu tube with PVCunsheather copper leads from terminals to the filling(PWD SOR P.NO : 115,S.NO 16.B) |
| 136 | Supply and fixing of 18W LED 3000K round typeresessed fiiitng (Philips/Havells) complete with T.Wround blocks on wall or ceiling with flu tube with PVCunsheather copper leads from terminals to the filling(PWD SOR P.NO : 115,S.NO 16.B) |
| 137 | 9 Metre Length single Bracket Pole with Base Plate (300 x 300 x 6mm) 114.30mm OD x 5.40mm Thick x5000mm Length, 88.90mm OD x 4.85mm Thick x2000mm Length, 76.10mm OD x 3.25mm Thick x2000mm Length PWD SOR P.NO 149 |
| 138 | Supply and fixing of 60W LED Street Light Fitting withLED (Philips/Havells) completePWD SOR P.NO 115 |
| 139 | Supplying and erectingof 12 Mtrs.Mini Mast TowerPolygonal Shapes. Suitable for 12 luminaries for WindSpeed up to 180 Km/hr. As per IS -875 Parts -3 Material Cons.: BSEN 10025 # Mechanical Components including Head Frame & Pulley Assay, Winch Bracket, Lantern Carriage Ring, Luminaries and C.G Box Mtg. Arms, Resting Bracket Guide Ring, Compensating Disc, Lightening Arrestor.etc. ( Each Set ) # Wire Rope, Safety Wire Rope, D Suckle Clamps, Nuts and Bolts. # Cable with termination & distribution box. # Foundation A0.45essories. # Winch Assembly # Power tool. Mast bottom Dia:415 mm. Top : 150 mm, Thk: 4,3,3 mm. Motor-1.Feeder pillar box comprising 100 ams fuse unit 24 hours timer 1-nos and contactor 1-nos outgoing MCB toggle switch and neutral link with internal wiring made of MS sheet and vermin proof.Erection and commissioning of 20 Mtr high mast on the above said concrete foundation using suitable equipments. Fixing of flood light luminaries in the lantern carriage including internal wiring & using flexible copper cable complete. HalonixLED Flood light 150W ( CW ) 12 nos (PWD SOR P.NO :151) |
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail