Construction Of Office And Store Room For Swm Project At Gopalbati Gram Panchayat Under Balurghat Development Block. Activity Code No.- 66107987 / 22-23
Tender Value
3.89 Lakhs
Estimated cost
Bid Submission
12 Dec 2022
0 days left
EMD
7800
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
gopalbati → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Office And Store Room For Swm Project At Gopalbati Gram Panchayat Under Balurghat Development Block. Activity Code No.- 66107987 / 22-23
BOQ
| Sl. No. | Item Description |
| 1 | soil including removing vegetation inequalities not exceeding 15 cm depth and disposal of the rubbish within a lead upto 75 m as directed. |
| 2 | Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete.(a) Depth of excavation not exceeding 1,500 mm. |
| 3 | Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc.layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work)(a) With earth obtained from excavation of foundation. |
| 4 | (B) Filling in foundation or plinth by fine sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the costof supply of sand. (payment to be made onmeasurement of finished quantity) |
| 5 | Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. |
| 6 | Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes.a) Pakur Variety |
| 7 | Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes.(i) Pakur Variety |
| 8 | Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor)(f) 25 mm to 30 mm shuttering without staging in foundation |
| 9 | Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor)(a) 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In- Charge. |
| 10 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction.(a) For works in foundation, basement and upto roof of ground floor/upto 4 m(i) Tor steel/Mild SteelOther than SAIL/ TATA/RINL |
| 11 | Brick work with 1st class bricks in cement mortar (1:6)(a) In foundation and plinth |
| 12 | Brick work with 1st class bricks in cement mortar (1:6)(b) In superstructure, ground floor |
| 13 | 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor. |
| 14 | Artificial stone in floor, dado, staircase etc with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners including raking out joints or roughening of concrete surface and application of cement slurry before flooring works using cement @ 1.75 kg/sq.m all complete including all materials and labour In ground floor.3 mm. thick topping (High polishing grinding on this item is not permitted with ordinary cement). Using grey cement(ii) 25 mm. thick |
| 15 | Supplying and laying Polythene Sheet (150gm / sq.m.) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches. |
| 16 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface](i) With 1:6 cement mortar(b) 20 mm thick plaster |
| 17 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface](i) With 1:6 cement mortar(C) 15 mm thick plaster |
| 18 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface](ii) With 1:4 cement mortar(c) 10 mm thick plaster |
| 19 | Neat cement punning about 1.5mm thick in wall,dado,window sill,floor etc.NOTE:Cement 0.152 cu.m per100 sq.m. |
| 20 | Wood work in door and window frame fitted and fixed in position complete including aprotective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps.(The quantum should be correted upto three decimals).(i) Other Local Wood. |
| 21 | Panel shutters of door and window, as perdesign (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings.In ground floor.(In case of non-supply of single plank,penal rate of reduction of 20% will be made)(iii) 35mm thick shutters with 19mm thick panel of size 30to 45 Cm.(c) Other Local Wood. |
| 22 | Cement washing including cleaning and smoothening surface thoroughly (cement to be used @15 kg./100 sq.m. of surface for one coat and @25 kg./100 sq.m of surface for two coats):External surface (Ground floor)(b) Two coats (on new works only). |
| 23 | Synthetic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturer\"s specification) including cleaning andsmoothning of surface.Two Coats |
| 24 | Applying decorative cement based paint of approved quality after preparing the surface including scraping the same thoroughly (plastered or concrete surface) as per manufacturer\"s specification.In Ground floor:(iii) Two coats. |
| 25 | (a) Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 26 | (b) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 27 | (A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary :(a) On timber or plastered surface :With super gloss (hi-gloss) -(iv) Two coats (with any shade except white) |
| 28 | (A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary :(b) On steel or other metal surface :With super gloss (hi-gloss) -(iv) Two coats (with any shade except white) |
| 29 | Supplying, fitting and fixing M.S. clamps fordoor and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately)(a) 40mm X 6mm, 250mm Length |
| 30 | Supplying, fitting and fixing M.S. clamps fordoor and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately)(b) 40mm X 6mm, 200mm Length |
| 31 | Iron butt hinges of approved quality fitted andfixed with steel screws, with ISI mark.(i) 50mm. X 37mm. X 1.50mm. |
| 32 | Iron butt hinges of approved quality fitted andfixed with steel screws, with ISI mark.(iii) 75mm. X 40mm. X 1.12mm. |
| 33 | Iron catch hook of approved quality fitted andfixed to shutter and chowkat.(a) 6mm dia x 100mm long. |
| 34 | Iron socket bolt of approved quality fitted andfixed complete.(b) 100mm long x 10mm dia bolt. |
| 35 | i) Iron hasp bolt of approved quality fitted andfixed complete (oxidised) with 16mm dia rodwith centre bolt and round fitting.(a) 200mm long |
| 36 | Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed(a) With continuous plate base (Hexagonal / Round rod)(vi) 150 mm grip x 10 mm dia rod. |
| 37 | Supplying fitting approved type ventilator inposition after cutting holes in walls setting in cement mortar mending damages to wall and plaster and two coats of paint of approved brand sand shade. Payment of mending two damages of wall & plaster and painting to be made separately.(a) C.I. ventilator of 5 mm. thick(i) Upto 0.10 sq.m. area |
| 38 | Supplying, fitting and fixing Fan Hook for ceiling with 1 metre long 16mm. dia rod complete including mending damages.Payment for damage and repair to be made separately. |
| 39 | Add GST |
| 40 | Add Cess |
AI Tender Summary
Tender Timeline
Dec 02, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedDec 12, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedDec 15, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender