Military Engineer Services-MES has published Tender For Special Repairs To Lt Feeder Pillar Box And Cable, Earth Pits,Amf Panels And Connected Items At Ramnad Under Ge Tirunelveli. Submission Date for this Tender is 20-12-2022. Feeder Pillar Tenders in Ramanathapuram Tamil Nadu. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | Excavating in trenches, not exc 1.5m wide and not exc 1.5m in depth; for laying pipes and getting out in any type ofsoil, complete all as specified and as directed by the Engineer-in-Charge. |
| 2 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil, complete all as specified and as directed by the Engineer-in-Charge. |
| 3 | Removing excavated soils n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and as directed by the Engineer-in-Charge. |
| 4 | Spreading of riddled earth obtained from trenchesfor cable cushioning on top and bottom of cable as specified for cable protection complete all as specified and directed. (Note: Only punned thickness of riddled earth shall be measured) |
| 5 | Supply and laybricks in trenches , common burnt clay building bricks, subclass `B’ designation 75, old size ,with width equal to thelength of the brick; complete all as specified and directed. |
| 6 | Cutting existing bituminous road and excavating in trenches, not exc 1.5m wide and not exc 1.5m in depth by cutting existing bituminous road not exc 10 sq. m on plan and not exc 1.5m in depth and getting out in any type ofsoil, complete all as specified and as directed by the Engineer-in-Charge. |
| 7 | Demolition of Cement concrete (unreinforced) in ground floors and pavings n exe 15 cm thickness (below or above ground level) complete all as specified and as directed by the Engineer-in-Charge. |
| 8 | Material and labour for 100 mm thick cement concrete 1:2:4 type B-1, using 20mm graded aggregate for making good the disturbed road surface after laying of pipe line over returned filled and compacted earth surface to match with existing road level complete all as specified and as directed. |
| 9 | Supply and lay LT under ground cable 1100 volts grade Cross linked Polyethylene (XLPE) insulated PVC Sheathed Cables: armoured multistranded heavy duty electric cable with aluminium conductor laid in trenches/ duct / walls including cable gland and lugs on both end termination including laying, connecting to various switches inpanel board, testing and commissioning etc including taking out existing unserviceable cables of following sizes complete all as directed & as specified:- |
| 10 | (a)3.5 Core35 Sqmm |
| 11 | (b)3.5 Core70 Sqmm |
| 12 | (c)3.5 Core120 Sqmm |
| 13 | (c)3.5 Core150 Sqmm |
| 14 | Material and labour for earthing complete with galvanised steel earth plate electrode60cm×60cm× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to 32x6mm GI strip as earthing lead by means of bolts, nuts, check nuts and washers of copper all as shown in electrical plate No.3 connected to earthing test point, including 20 mm GI pipe (Medium grade) for watering and 40 mm GI pipe (Medium grade) for protection of earth strip andetc..including testing on completion ,PCC chambers in PCC1:3:6 type C1, RCC M25 type cover slab 50mm thick with 8mm dia TMT HCR/CRS steel bars at 140mm C/C both way and lifting handle GI funnel & wire mesh ,funnel, lugs and charcoal, salt etc all as applicableincluding taking down old unserviceable earthing complete for taking into creditall as specified and as directed by the Engineer-in-ChargeNote:-(i) The rates quoted is inclusive of32x6mm GI strip earthconductor upto a length of 7.5m from the earth pit. |
| 15 | Supply and lay earth continuity conductor or main earthing lead fixed to wall on batten or recess or buried in ground or drawn in conduit / conduit pipe or fixed to poles or any other indicted situation for loop earthing etc of galvanised steel earth stripof size 32 X 6mm including taking down old unserviceable earth strip complete for taking into credit complete all as specified and as directed by the Engineer-in-Charge |
| 16 | Material and labour for earthing complete with galvanised steel earth plate electrode60cm×60cm× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised steel earth wire 4mm diaas earthing lead by means of bolts, nuts, check nuts and washers of copper all as shown in electrical plate No.3 connected to earthing test point, including 20 mm GI pipe (Medium grade) for watering and 40 mm GI pipe (Medium grade) for protection of earth strip andetc..including testing on completion ,PCC chambers in PCC1:3:6 type C1, RCC M25 type cover slab 50mm thick with 8mm dia TMT HCR/CRS steel bars at 140mm C/C both way and lifting handle GI funnel & wire mesh ,funnel, lugs and charcoal, salt etc all as applicable including taking down old unserviceable earthing complete for taking into credit complete all as specified and as directed by the Engineer-in-Charge complete all as specified and as directed by the Engineer-in-ChargeNote:-(i) The rates quoted is inclusive of32x6mm GI strip earthconductor upto a length of 7.5m from the earth pit. |
| 17 | Supply and lay earth continuity conductor or main earthing lead fixed to wall on batten or recess or buried in ground or drawn in conduit / conduit pipe or fixed to poles or any other indicted situation for loop earthing etc of galvanised steel earth wire 4mm dia including taking down old unserviceable GI earth wirecomplete all as specified and as directed. |
| 18 | Supply, fix , testing in repair ofACB 4 Pole, 415 V, Manual Draw out type with microprocessor release of capacity 1250 Amps in a existing AMF Panel including modifications suitable for the new ACB and making necessary end termination in the incoming and outgoing cables complete all as specified and as directed by the Engineer-in-Charge. |
| 19 | Supply, fix , testing in repair ofAutomatic Transfer Switch with sheet metal enclosure 415 V, 160 A complete with relay panel and switch gears for automatic starting on main failure and making necessary end termination of the incoming and outgoing cables complete all as specified and as directed by the Engineer-in-Charge. |
| 20 | Supply, fix , testing in repair ofAutomatic Transfer Switch with sheet metal enclosure 415 V, 250 A complete with relay panel and switch gears for automatic starting on main failure and making necessary end termination of the incoming and outgoing cables complete all as specified and as directed by the Engineer-in-Charge. |
| 21 | Material and labour for writing letters (Block Roman, Italic or Indian) with thick paint ,stand out boldly and solidly without showing signs of brush marks, if necessary, repainted until the desired result isobtained , not exc30 cm height and painting with contrasting colour in the background of letter complete all as specified and as directed by the Engineer-in-Charge.NOTE: Colour of paint shall be decided by the Engg-in-charge. |
| 22 | Supply , installation, testing and commissioningof outdoor LT feeder pillar box panel board in replacement , CPRI Approved ,made out of CRCA sheet 3.15 mm thick vermin proof factory madewith 40 x 40 x 6 mm MS angle/channelduly painted with two coats of synthetic enamel powder coated paint over a coat of metal primer with bus bar chamber comprising of high conductivity Aluminium bus bar of capacity 600 Amps three phase andfor neutral including voltmeter, Ammeter selector switches, PCC foundationsuitable to accommodate the following as specified and as directed.:- INCOMING (a)MCCB 415 V,250 A, 4 polewith over load , short circuit protection,breaking capacity 25 KA-01 Nos (b) On-load change over switch 250 A- 01 Nos.OUT GOING (a) MCCB 160 A, 415V , 4 pole ,breaking capacity 16 KA - 01 Nos (b) MCCB 100 A, 415V 4 pole ,breaking capacity 16 KA - 01 Nos(c) MCCB 63 A, 415V , 4 pole ,breaking capacity 16 KA - 05 Nos (d) MCB 32 A, 415V- 03 NosDigital Panel Meter Multifunctional type for Amps, Volts, KWH, Power Factor and other parameters flush mounting with LED indication lamp, CT Coil complete and all as per standard practice ---8 nos Note :-(i) All MCCBs / instruments / MCBs /Bus Bar shall be housed in a separate housing with on- off latches in the housing |
| 23 | Supply , installation, testing and commissioningof outdoor LT feeder pillar box panel board in repair , CPRI Approved ,made out of CRCA sheet 3.15 mm thick vermin proof factory madewith 40 x 40 x6 mm MS angle/channelduly painted with two coats of synthetic enamel powder coated paint over a coat of metal primer with bus bar chamber comprising of high conductivity copper bus bar of capacity 400 Amps three phase andfor neutral including voltmeter, Ammeter selector switches, PCC foundationsuitable to accommodate the following as specified and as directed.:- INCOMING (a) MCCB 415 V,200 A, 4 polewith over load , short circuit protection,breaking capacity 25 KA- 01 Nos.(b) On-load change over switch 200 A- 01 Nos.OUT GOING (a) MCCB 100 A, 415V , 4 pole ,breaking capacity 16 KA - 01 Nos(b) MCCB 63 A, 415V , 4 pole ,breaking capacity 16 KA - 03 Nos (c) MCB TPN 32 A, 415V 4 pole ,breaking capacity 10 KA - 03 NosDigital Panel Meter Multifunctional type for Amps, Volts, KWH, Power Factor and other parameters flush mounting with LED indication lamp, CT Coil complete and all as per standard practice ---5 nos Note :-(i) All MCCBs / instruments / MCBs /Bus Bar shall be housed in a separate housing with on- off latches in the housing |
| 24 | Supply , installation, testing and commissioningof outdoor LT feeder pillar box panel board in repair , CPRI Approved ,made out of CRCA sheet 3.15 mm thick vermin proof factory madewith 40 x 40 x6 mm MS angle/channelduly painted with two coats of synthetic enamel powder coated paint over a coat of metal primer with bus bar chamber comprising of high conductivity copper bus bar of capacity 1600 Amps three phase andfor neutral including voltmeter, Ammeter selector switches, PCC foundationsuitable to accommodate the following as specified and as directed.:- INCOMING (a) ACB 415 V,800 A, 4 polewith over load , short circuit protection,breaking capacity 50 KA- 01 Nos. (b)On-load change over switch 800 A- 01 Nos. OUT GOING (a) MCCB 160 A, 415V , 4 pole ,breaking capacity 25 KA - 05 Nos(b) MCCB 125 A, 415V , 4 pole ,breaking capacity 25 KA - 01 Nos (c) MCCB 100 A, 415V , 4 pole ,breaking capacity 25 KA - 03 Nos(d) MCCB 63 A, 415V , 4 pole ,breaking capacity 16 KA - 06 NosDigital Panel Meter Multifunctional type for Amps, Volts, KWH, Power Factor and other parameters flush mounting with LED indication lamp, CT Coil complete and all as per standard practice ---15 nos Note :-(i) All MCCBs / instruments / MCBs /Bus Bar shall be housed in a separate housing with on- off latches in the housing complete |
| 25 | Supply , installation, testing and commissioningof outdoor LT feeder pillar box panel board in repair , CPRI Approved ,made out of CRCA sheet 3.15 mm thick vermin proof factory madewith 40 x 40 x6 mm MS angle/channelduly painted with two coats of synthetic enamel powder coated paint over a coat of metal primer with bus bar chamber comprising of high conductivity copper bus bar of capacity 800 Amps three phase andfor neutral including voltmeter, Ammeter selector switches, PCC foundationsuitable to accommodate the following as specified and as directed.:- INCOMING (a) MCCB 415 V,400 A, 4 polewith over load , short circuit protection,breaking capacity 25 KA- 01 Nos. (b) On-load change over switch 400 A- 01 Nos.OUT GOING (a) MCCB 200 A, 415V , 4 pole ,breaking capacity 16 KA - 02 Nos (b) MCCB 160 A, 415V 4 pole ,breaking capacity 16 KA - 01 Nos(c) MCCB 100 A, 415V , 4 pole ,breaking capacity 16 KA - 02 Nos (d) MCCB 63 A, 415V 4 pole ,breaking capacity 16 KA - 02 Nos Digital Panel Meter Multifunctional type for Amps, Volts, KWH, Power Factor and other parameters flush mounting with LED indication lamp, CT Coil complete and all as per standard practice ---8 nos Note :-(i) All MCCBs / instruments / MCBs /Bus Bar shall be housed in a separate housing with on- off latches in the housing complete |
| 26 | Supply , installation, testing and commissioningof outdoor LT feeder pillar box panel board in repair , CPRI Approved ,made out of CRCA sheet 3.15 mm thick vermin proof factory madewith 40 x 40 x6 mm MS angle/channelduly painted with two coats of synthetic enamel powder coated paint over a coat of metal primer with bus bar chamber comprising of high conductivity copper bus bar of capacity 500 Amps three phase andfor neutral including voltmeter, Ammeter selector switches, PCC foundationsuitable to accommodate the following as specified and as directed.:- INCOMING (a) MCCB 415 V,250 A, 4 polewith over load , short circuit protection,breaking capacity 25 KA- 01 Nos.(b) On-load change over switch 250 A- 01 Nos. OUT GOING (a) MCCB 125 A, 415V , 4 pole ,breaking capacity 16 KA - 01 Nos (b) MCCB 100 A, 415V 4 pole ,breaking capacity 16 KA - 02 Nos(c) MCCB 63 A, 415V , 4 pole ,breaking capacity 16 KA - 03 NosDigital Panel Meter Multifunctional type for Amps, Volts, KWH, Power Factor and other parameters flush mounting with LED indication lamp, CT Coil complete and all as per standard practice ---7 nos Note :-(i) All MCCBs / instruments / MCBs /Bus Bar shall be housed in a separate housing with on- off latches in the housing complete and all as per standard practice. |
| 27 | Supply , installation, testing and commissioningof outdoor LT feeder pillar box panel board in repair , CPRI Approved ,made out of CRCA sheet 3.15 mm thick vermin proof factory madewith 40 x 40 x6 mm MS angle/channelduly painted with two coats of synthetic enamel powder coated paint over a coat of metal primer with bus bar chamber comprising of high conductivity copper bus bar of capacity 800 Amps three phase andfor neutral including voltmeter, Ammeter selector switches, PCC foundationsuitable to accommodate the following as specified and as directed.:- INCOMING (a) MCCB 415 V,500 A, 4 polewith over load , short circuit protection,breaking capacity 36 KA- 01 Nos.(b) On-load change over switch 400 A- 01 Nos. OUT GOING (a) MCCB 160 A, 415V , 4 pole ,breaking capacity 16 KA - 03 Nos(b) MCCB 100 A, 415V , 4 pole ,breaking capacity 16 KA - 03 Nos (c) MCCB 63 A, 415V , 4 pole ,breaking capacity 16 KA - 04 Nos (d) MCB TPN 32 A, 415V , - 02 Nos Digital Panel Meter Multifunctional type for Amps, Volts, KWH, Power Factor and other parameters flush mounting with LED indication lamp, CT Coil complete and all as per standard practice ---7 nos Note :-(i) All MCCBs / instruments / MCBs /Bus Bar shall be housed in a separate housing with on- off latches in the housing complete |
| 28 | Supplying and layingGI pipe light grade of size 50mm diafor protection of UG cable on walls/under floors/road crossings/in trenchesincluding taking down old unserviceable earthing GI pipe for taking into credit complete all as specified and as directed by the Engineer-in-Charge complete. |
| 29 | Supplying and layingGI pipe light grade of size 80mm dia for protection of UG cable on walls/under floors/road crossings/in trenchesincluding taking down old unserviceable earthing GI pipe for taking into credit complete all as specified and as directed by the Engineer-in-Charge complete.. |
| 30 | Supply and fix danger notice plate of 1.6mm thick mild steel sheet, vitreous enameled white, with letters, figures and conventional skull and bones in signal red colour and fixed with M.S. clamps, bolts and nuts of approved size, for LT, 20x15cm size, , complete all as specified and as directed by the Engineer-in-Charge |
| 31 | Supplying and laying synthetic Rubber insulated mats 2 mm thick for voltage upto 3.3 kv for electrical purpose as per IS 15652-2006, (superseding IS 5424) suitable for electrical shock safety of sizes 2m x 1m complete all as specified and as directed by the Engineer-in-Charge. |
| 32 | Material and labour for cable route indicator 150mm dia 3mm thick made out of cast aluminum duly marked with size and type of cable fixed on 40x40x6mm angle iron support embedded in PCC 1;2:4 type B1 using 20 mm graded (300x300x400mm size) and painted with 2 coats of anticorrosive paint over a coat of red oxide primer all as specified and as directed. |
| 33 | Schedule of credit amount brought back from Ser Page No.34- Rs. 1,23,530.00 will be deducted from the above quoted amount to derive the contract sum. SIGNATURE OF CONTRACTOR |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
