Tender For Construction Of Community Toilet At Uttar Dalkhola At Ward No-11 Under Dalkhola Municipalityunder Dalkhola Municipality
Tender Value
7.78 Lakhs
Estimated cost
Bid Submission
05 Dec 2022
0 days left
EMD
15564
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
dalkhola → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Community Toilet At Uttar Dalkhola At Ward No-11 Under Dalkhola Municipalityunder Dalkhola Municipality
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 01-Dec-2022 | Date Extension Corrigendum | Date | 05-Dec-2022 |
BOQ
| Sl. No. | Item Description |
| 1 | Earthwork in excavation in foundation trenches or drains, in all sorts of soil( including mixed soil but excluding laterite or sandstone ) including trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water etc. as required complete.(M1) a) Depth of excavation not exceeding 1500mm. |
| 2 | Earth work in filling in foundation trenches or plinth with good earth in layers not exceeding 150mm. including watering and ramming etc. layer by layer complete ( Payment will be made on the basis of measurement of finished quantity of work.).(M1) a) Withearth obtained from excavation of foundation. Assuming 1/5 th of excavation |
| 3 | Filling in foundation or plinth by silver sand in layers not exceedng 150mm. as directed and consolidation same by through saturation with water ramming complex complete including the cost of supply of sand ( Payment to be made on measurement of compacted vollume). (M1 By silver sand.filling below floor |
| 4 | Single brick flat soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with powdered earth or local sand. (M1) |
| 5 | Supplying and laying Polythene Sheet (150gm / sq.m.) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches.Floor(M1) |
| 6 | Ordinary cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size ) excluding shuttering and reiforcement , if any , in ground floor as per releventIS codes. a) Pakur Variety. (P-24 of 315, It-4)(M1) |
| 7 | Nominal Mix M - 20 Cement concrete with graded stone chips ( 20mm size) excluding shuttering and reinforcement, if any. Pakur variety.(M1) |
| 8 | Hire and labour charges for shuttering with centering and necessary staging upto 4m. using approved stout props and thick hard wood planks of approve thickness with required bracing for concrete slabs, beams, columns, lintels curved or straight including fitting, fixing and striking out after completion of works.(M1) (f) 25 mm to 30 mm shuttering without staging in foundation |
| 9 | (a) 25 mm to 30 mm thick wooden shuttering as per decision & direction ofEngineer-In-Charge(M1) |
| 10 | Reinforcements for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc. including supply of rods, initial straightening and removal of loose rust ( if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16G black snnealed wire at every intersection, complete as per drawing and direction. (M1) |
| 11 | Brick work with 1st class bricks in cement mortar (1:4) (M1)a) In foundation and plinth |
| 12 | 125mm thick brick work with 1st class bricks in cement mortar( 4:1).(M1) a) In ground floor. |
| 13 | 25mm. thick damp proof course with cement concrete with stone chips (1:1.5:3) [with graded stone aggregate 10 mm nominal size] and admixture of water proofing compound as per manufacturer\"s specification followed by two coat of polymer based paint, (1st coat after 4 to 5 days ofconcrete laying and 2 nd coat just before brick masonry work) as directed (cost of water proofing compound & polymer basedpaint to be paid separately).( Chequering not required over concrete or painted surface).(M1) |
| 14 | Supplying, fitting and fixing Marble Slab/tile of 15 to 18 mm thickness in floor, lobby, stair, landing & treads etc. over 20 mm (av.) thck base of Cement mortar (1:2) laid with white cement slurry @ 4.4 kg/Sq.m before placing marble & jointedwith white cement slurry @ 2.0 kg/Sq.m with necessary pigments including grinding and Granite polishing as per direction of Engineering -in -Charge in Ground Floor.(b) With Chawk Dungri(iii) Area of each tile exceeding 0.6 sq.m but not excedding 1sq.m.For urinal partition |
| 15 | Extra cost of labour for prefinished and premoulded Nosing to treads of steps, railing, window sill etc. of Marble Stone. |
| 16 | Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles includingroughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc.(M1)(B) WallWith Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m. (b) Area of each tile above 0.09 Sq.m(i) Coloured decorative |
| 17 | (A) FloorWith Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m.(b) Area of each tile above 0.09 Sq.m(i) Coloured decorative (M1) |
| 18 | Collapsible gate with 40mm x 40mm x 6mm Tee as top and bottom guide rail, 20mm x 10mm x 2mm vertical channels 100mm apart in fully stretched position 20mm x 5mm M.S. flats as collapsible bracings properly rivetted and washered including 38mm steel rollers including locking arrangements, fitted and fixed in positionwith lugs set in cement concrete and including cutting necessary holes, chasing etc. in walls, floors etc. and making good damages complete. |
| 19 | Supplying, fitting and fixing windows and ventilators with or without integrated grills conforming to IS 1038-1975 and manufactured from rolled steel sections conforming to IS 7452-1974 with non-friction projecting type, box type hinges, glazing clips, lugs locking bracket,handle plate etc, including hoisting in position, straightening if required, fixing lugs in cement concrete ( 1:2:4) with stone chips 20 mm down cutting holes and mending good damages to match with existing surface complete in all respect excluding glazing. (b) Openable steel windows as per IS sizes with side hung shuttersand horizotal glazing bars. [The extra rate admissible for theopenable portion only] |
| 20 | (iii) Centre hung ventilators as per I.S. sizes 580 mm (M1) |
| 21 | (iv) Two point nose steel handle including fitting and fixing.(M1) |
| 22 | (vi) steel peg stay 300 mm long including fitting and fixing. (M1) |
| 23 | (viii) M.S. integrated grill as per approved design integrated with steel window or ventilator, joints continuously welded with M.S. flats and bars.(M1) |
| 24 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface](ii) With 1:4 cement mortar (c) 15 mm thick plaster(Outer wall) (M1) |
| 25 | (a) 20 mm thick plaster (Inner)(M1) |
| 26 | 10 mm thk (Roof)(M1) |
| 27 | Neat cement punning about 1.5mm thick in wall dado, window sill, floor etc.NOTE:Cement 0.152 cu.m per100 sq.m. (M1) |
| 28 | Making ornamental R.C. hand rail upto 160 sq.cm. cross sectional area excluding cost of reinforcement and including cost of shuttering with (1:1.5:3) cement concrete in stone chips, plastered 15 mm. thick (1:4), neat cement finishing and polishing complete as per direction of Engineer-in-charge. (Cement 10.0Kg/Mtr.) In ground floor. (E7) (p-185, It-7) |
| 29 | Supplying, Fitting & Fixing 30 mm thick Factory made solid Panel PVC Door Shutter consisting of outer frame made out of M.S. tubes of 19 gauge thickness and size 19 mmx19 mm for styles, top and bottom rails, M.S. frame shall have cost of steel primers of approved make and manufacture, M.S. frame covered with 5 mm th. heat moulded PVC “C” channel of size 30 mm th, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on either sides forming styles; and 5 mm th. 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm tapered in 45 degree on the inner side to form top & bottom rail and 115 mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided either side of the panel with 10 mm (5 mmx2) th.,20 mm wide cross PVC sheet as gap insert for top rail and bottom rail. Paneling of 5 mm th. both side PVC sheet to be fitted in the M.S. frame welded/sealed to the styles &rails with 7 mm (5 mm+2 mm) th.x15 mm wide PVC sheet beading on inner side and joined together with solvent cement adhesive. An additional 5 mm th. PVC strip of 20 mm which is to be stuck on the interior side of the “C” channel using PVC solvent adhesive etc. complete excluding all necessary hardwares as per direction of Engineer-in-Charge.In ground floor. (p-125-IT-15) (M1) |
| 30 | (a) Priming one coat on steel or other metal surface with synthetic oil bound primer (p-200, It-1) (M1) |
| 31 | A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : (b) On steel or other metal surface :(iv) Two coats (with any shade except white)(p-200, It-2)(M1) |
| 32 | Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer\"s specification and as per direction of theEIC.(a) One Coat Outer wall(p-196,It-8)(M1) |
| 33 | Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturer\"s specification)including cleaning and smoothning of surface.Two Coats Outer wall (M1) |
| 34 | Supplying, fitting and fixing PVC pipes for underground work ofapproved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted including cost of all materials ,jointing materials, cutting pipes, making threads ,cutting trenches upto 1.5 metre below surface in all sorts of soil and refilling the same as directed complete in all respect. (Payment will be made on the centre line measurement of the total pipe line including all specials No separate payment will be made for accessories, specials.) (i)15 mm dia medium quality |
| 35 | 25 mm dia |
| 36 | Supplying P.V.C. water storage tank of approved quality with closed top with lid (Black) - Multilayer(i) 500 litre |
| 37 | Supplying, fitting and fixing bib cock or stop cock. a) (i) Chromium plated Bib Cock short body (Equivalent to Code No. 511& Model - Tropical / Sumthing Special of ESSCO or similar brand).(M1) |
| 38 | (b) (i) Chromium plated Stop Cock (Equivalent to Code No. 513(A) &513(B) & Model - Tropical / Sumthing Special of ESSCO or similar |
| 39 | Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992 (ii) Double Socketed 3 Meter Length (b) 110 mm |
| 40 | Vent CowlB) 110 mm |
| 41 | Pipe Clip(b) 110 mm |
| 42 | coupler |
| 43 | plain tee |
| 44 | door tee |
| 45 | D) Solvent Cement 250 ML |
| 46 | Labour for fitting and fixing U.P.V.C. pipes for above ground work including cost of jointing materials etc. fitting and fixing all necessary specials, cutting pipes, cutting holes in walls or R.C. floor where necessary and mending good all damages excluding the cost of masonry or concrete work, if necessary, but including the cost and fitting and fixing holder bat clamps (any floor) or for underground work including cutting trenches upto 1.5 metre and refilling the same complete as per direction of the Engineerin-charge. (Payment will be made on centre line measurement of the total pipeline including specialsii) 110 MM dia(p-74It-24) (M1) |
| 47 | a) (i) Chromium plated round shower with revolving joint 100 mm dia with rubid cleaning system (Equivalent to Code No. 542(N) & Model - Tropical / Sumthing Special of ESSCO or similar brand).(p-3,It-3,a) (M1) |
| 48 | Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc.. (p-36,it-2) (M1) |
| 49 | Wash basin vitreous china of approved make (without fittings) supplied,fitted and fixed in position on 75mm X 75 mm X 75 mm wood blocks and C.I. brackets including two coats of painting of C.I. brackets.(iii) 630 mm X 450 mm size (p-41,It-1) (M1) |
| 50 | Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of pproved make in position complete excluding \"P\" or \"S\" trap (excluding cost of concrete for fixing) . (ii) 530 mm X 410 mm(p-79, It-4) (M1) |
| 51 | Supplying, fitting and fixing Flat back urinal (half stall urinal) in white vitreous chinaware of pproved make in position with brass screws on 75 mm X 75 mm X 75 mm wooden blockscomplete.(ii) 470 mm X 280 mm X 340 mm(p-80,It-6) (M1) |
| 52 | Supplying,fitting and fixing approved brand 32 mm dia.P.V.C. waste pipe, with PVC coupling at one end fitted with necessary clamps.iii) 900 mm long (p-43,It-10)(M1) |
| 53 | Supplying,fitting and fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia. (iii) 600 mm long(p-43, It-9) (M1) |
| 54 | Supplying, fitting and fixing pillar cock of approved make.a)(i) CP Pillar Cock - 15 mm. (Equivalent to Code No. 507 & Model -Tropical / Sumthing Special of ESSCO or similar brand). |
| 55 | Supplying, fitting and fixing Foot rest for water closet of size 275 mm X 125mm with(b) Porcelain of approved make. |
| 56 | Supplying, fitting and fixing best quality Indian make mirror 5.5 mm thick with silvering as per I.S.I. specifications supported on fibre glass frame of any colour, frame size 550 mm X 400 mm |
| 57 | Supplying, fitting and fixing liquid soap container. (a) Cromium plated. |
| 58 | Supplying, fitting and fixing porcelain toilet paper holder of approved make with wooden spindle as necessary.(i) Roll type size 250 mm X 125 mm |
| 59 | Supplying, fitting and fixing towel rail with two brackets. (ii) 25 mm dia. and 600 mm long |
| 60 | Construction of septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar (1:4) including two 560 mm dia. R.C.C. manhole cover(heavy type)of approved make supplied, fitted and fixed in the 100mm thick R.C.C (1:1.5:3) top slab with necessary fittings, 20mm thickcement plaster (4 : 1) with neat cement finish to the internal surfaces and 15 mm thick cement plaster (4 : 1) to outside wall upto 200 mm below G.L floor finished with 25 mm thick grey artificial stone over 100 mm thick R.C.C(1:1.5:3) bottom slab including supplying, fitting and fixing all necessry specials, fittings, S.W. tees, C.I. foot rest etc. including excavation earth in all sorts of soil, shoring, bailing out and pumping out water as necessary, ramming, dressing the bed and fefilling the sides of the tanks with earth, emoving spoils, filling up the chamber with clear water, removing foreign materials from the chamber and including constructing attached inspection pit as per approved drawing and connecting all necessary pipes, joints etc. with internal plaster work and artificial stone flooring is to be done with admixture of water proofing compound @ 0.5% by weight of cement with all costs of labour and materials. Note:- (i) Finished level of Septic Tank should be 400 mm. from Ground Level. (ii) Height of 50 mm. Ventilation pipe &Mosquito proof mesh, should be follwed as per IS:2470,Part- I.Payment will be made separetly on the basis of actual height based on relevantI.S.Code. (v) For 30 users A) With Pakur variety. (JSW/SHYAM) |
| 61 | Construction of circular soak well 2.5 metre deep in all types of sandy soils with dry brick work upto 1.6 metre from the bottom having 150 mm intermediate cement brick work (1:4) band all round and cement brick work (1:4) upto 0.90 metre from top with 20mm thick cement plastering (1:4) to inside face upto the depth of cement brick work, 15mm thick cement plaster (1:4) on outer face from top of the well upto G.L. and 6 mm thick cement plaster (1:4) on top of the R.C.C. cover slab including filling bottom 1.00 metre of inside of the well with brick metal (50 mm to 63 mm size) including R.C.C. cover slab of 100 mm thick with cement conc (1:1.5:3) with stone chips with necessary reinforcement and shuttering including one 560 mm dia. R.C.C. manhole cover (heavy type)of approved make supplied, fitted and fixed in the cover slab with necessary fittings, making nacessary rrangements for pipe connections, excavation of well including shoring, dewatering and removing the exess earth from the premises as per direction complete in all respect with all costs of labour and materials. With 250 mm thick dry brick work and 250 mm thick cement brick work (1:6) and 1.00m inside dia.(JSW/SHYAM) |
| 62 | Constructing Inspection pit of inside measurement 600mm X 600mm X upto 600mm (depth) with 250 mm thick 1st. class brick work in cement mortar (1:4) on all sides, bottom of the pit consisting of 100 mm thick cement concrete (1:3:6) with stone chips over a layer of jhama brick flat soling, 15 mm thick (1:4) cement plaster to inside walls and out-side walls upto G.L. and 20 mm.thick (1:4) plaster to bottom of the pit, providing necessary invert with cement concrete (1:3:6) with stone chips as per direction, neat cement finishing to entire internal surfaces, top of the pit covered with 100 mm thick R.C.C. slab (1:1.5:3) with stone chips and necessary reinforcements upto 1% and shuttering including 6 mm thick cement plaster (1:4) in all external surfaces of the slab and one 560 mm dia. R.C.C. manhole cover of approved make supplied, fitted and fixed in the slab with necessary fittings, necessary earthwork in excavation in all sorts of soil, filling sides of the pit with earth and removing spoils after work complete in all respect with all costs of labour and materials. ii) With Bazree (N.B Variety) (JSW/SHYAM) |
| 63 | Supplying and Planting of different plant / trees ( Supplying well grown plants bushy and healthy, minimum height as specified i.e. exposed height including all leads & lift, carriage, handling, manuring, applying presticide and fertilizer etc.x) Ficus blakii (F. Vivicon) well branched (Bushy) of height 120cm - 135 cm in earthen pot of size 30cm.(A3)(p-261 it-9 x)(A3) |
| 64 | Maintanance of trees for one year (Avenue Plants) including watering, trimming, manuring, spraying insecticide and guarding as required. This includes supply of labour, tools & plants including materials. (A3) |
| 65 | Removal of rubbish,earth etc. from the working site and disposal of the same beyond the compound, in conformity with the Municipal /Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge. |
| 66 | Signage for public toiletACPBase&reflective vinyl (E8) |
| 67 | Supplying and fixing sinage with fixingstand post for public toilet for visible to passersby (E8) |
| 68 | Glow Signboard for displayed Name & Contact details, of the following are displayed prominently- Toilet identification number , name of ULB under whose jurisdiction and manintenance authority promnently displayed for each toilet block supervisoe, Supervisor\"s agency and area sanitary Inspector (D3) |
| 69 | Odonil toilet air freshner (pack of 4 nos) (D5) |
| 70 | Standard Plastic (12L) Dustbin (E3) |
| 71 | Air Freshner (Napthalin 250gm) (D5) |
| 72 | Supplying paper Napkin (A5) |
| 73 | Supplying sanitary Napkin (Whisper or similar make 50 pcs) (A6) |
| 74 | Harpic (Blue 500 ml)(E1) |
| 75 | Harpic (Red 500 ml) (E1) |
| 76 | Gala double lip floor wiper(M1) |
| 77 | Colin glass or surface cleaner(M1) |
| 78 | Muriatic acid (M1) |
| 79 | Bleaching Powder (M1) |
| 80 | Dettol, Lifebuy or similar make liquid soap (E4) |
| 81 | rubber hand Gloves(M1) |
| 82 | Double side Plastic brush(M1) |
| 83 | Plastic broom (M1) |
| 84 | Supply roaster / register for keeping account of regular cleaning(D1) |
| 85 | SMS/any other ICT based feedback system (with number displayed on which SMS has to be sent) (A9) |
| 86 | Distribution wiring in 2 x 22/0.3 (1.5 sqmm) single corestranded \"FR\" PVC insulated & unsheathed copper wire(Brand approved by EIC) in 20mm size PVC rigid conduit \"FR\"(Precision make), with 1x22/0.3 (1.5 sqmm) single corestranded \"FR\" PVC insulated & unsheathed copper wire forECC, to light/fan/call bell points with Piano Key type switchfixed on MS CRC sheet metal (16 SWG) switch board cumJB on wall complete with 2 no. suitable size “Ph & N” copperbar incl. bakelite/Perspex (wall matching color) top cover 3mm thick and incl. 175mmx100mmx65mm inspection box,making earthing attachment, painting the MS box andmending good the damages to original finish Average run 5 mtr(PWD Sch pg no- E-14;Item no-2(a) |
| 87 | Distn. wiring with 2 x 36/0.3 (2.5 sqmm) single core strandedcopper conductor PVC insulated and unsheathed copper wire(Brand approved by EIC) in 19mm dia 3 mm thick polythenepipe with 1x22/0.3 (1.5sqmm) PVC insulated and unsheathedcoper wire as ECC, complete with all accessories embeddedin wall (for 15 A plug point/exhaust fan point) (PWD Sch pg no- E-10;Item no-5 |
| 88 | Supplying and fixing double-door SPN MCB Distribution Board with IP-42/43 protection, concealed in wall after cutting the wall & mending good the damages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthing attachment Supplying and fixing double-door SPN MCB Distribution Board with IP-42/43 protection, concealed in wall after cutting the wall & mending good the damages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthing attachment2+4 way Enclosure (607710)PWD Sch pg no- D-9;Item no-13) |
| 89 | Supply and fixing240/415 V MCB of Breaking capacity 10KA & C charateristics on din rail of existing DBs and necessary connection 6-32A SP MCB.(Legrand)PWD Sch pg no- D-6;Item no-7) |
| 90 | Supply and fixing 240/415V MCB Islator on din rail of existing DBs and necessary connection. 32A DP MCB Isolator(Legrand). PWD Sch pg no- D-5;Item no-6) |
| 91 | Supply & Delivery of GI earth Spike(1830x20mm)Non Sch rate |
| 92 | Supply of Power coated Batten for T5 28W with replacable Electronic Ballast.(Model- BATTEN EZ T5 LHIT81128032)(Make- Havells/Bajaj/Philips) Non Sch Rate |
| 93 | Fixing only single/twin Florescent light fitting complete with all accessories directly on wall/ceiling by screws etc.(PWD sch page no- c-2;Item No 14a) |
| 94 | Supply of 9 watt LED Lamp(Havells). |
| 95 | Fixing only 1no lamp holder on single HW board on wall incl.S & F single HW board( D-13,itm 22) |
| 96 | Supply ,fixing energy saving LED outdoor Street Light fitting of (Havells/Bajaj/Philips) ENDURA CITYLITE PLATINUM PLUS (Model- ENDURACITYLITEPLATINUMPLUSSL30WLED757 SASYBOPC) Non Sch Rate |
| 97 | Fixing only outdoor / street light type fluorescent light fittingcomplete with all accessories to be fixed/projected from the wall of the building incl. making holes to building, S&F 40 mm dia GI pipe (ISI-Medium) 1.50 mts. average length, with GI socket at one end and thread at the other end & suitable bend to house the fitting & making necy. connections with S&F necy. length of 1.5 sqmm PVC insulated single core stranded annealed copper wire and making connections as required and mending good damages to wall and painting) PWD Sch pg no- C-3;Item no-19) |
| 98 | Supply of 12\" domestic metal exhaust fan(Model- Trans Air 12\" Grey)(Make- Crompton/Havells/Bajaj) Non Sch rate |
| 99 | Fixing only exhaust fan after making hole in wall and making good damages and smooth cement finish etc. as practicable as possible and providing necy. length of PVC insulated wire and making connection for exhaust of following diameter: 30 cm (12\") PWD Sch pg no- C-4;Item no-28(b) |
| 100 | Fixing only louver shutter/cowl on wall with necy. bolts & nuts(6 mm dia x 62 mm long) .For 30 cm (12\") Exhaust fan . PWD Sch pg no- C-4;Item no-30(b) |
| 101 | Supply & Fixing of 0.5 HP Monoblock pump motor set (Make- Cromptop,Havells) |
| 102 | Supply & Fixing 240 V, 25 A, Modular type starter (Brandapproved by EIC) with 25A Modular switch type DP MCB (CCurve)and 4 Module GI Modular type switch board with 4Module top cover plate flushed in wall incl. S&F switch board and cover plate and making necy. connections with PVC Cu wire and earth continuity wire etc. PWD Sch pg no- E-19;Item no-17) |
| 103 | Add GST @ 12% |
| 104 | Add Cess @ 1% |
AI Tender Summary
Tender Timeline
Dec 01, 2022
11:30 IST
Tender Published
Tender notice published.
Completed
Dec 05, 2022
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
CompletedDec 05, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedDec 07, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender