Tender For Extension Of Office Building-Cum-Teaching Block At Anjanthali, Mhu, Karnal (Re-Invited 1St Time)
Tender Value
2.84 Crore
Estimated cost
Bid Submission
28 Nov 2022
0 days left
EMD
5.68 Lakhs
Bank guarantee accepted
Document Fee
17700
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
karnal → Haryana
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Extension Of Office Building-Cum-Teaching Block At Anjanthali, Mhu, Karnal (Re-Invited 1St Time)
BOQ
| Sl. No. | Item Description |
| 1 | Description and details |
| 2 | CIVIL WORKSHSRITEMNO. 4.14 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.4.14.1 All kinds of soil |
| 3 | HSR ITEM NO.4.32Fillingavailableexcavatedearth(excludingrock)in trenches,plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. |
| 4 | HSRITEMNO. 4.39Providing and injecting chemical emulsion for PRE- CONSTRUCTIONALanti termite treatment and creating a chemical barrier under and around the column pits, walltrenches, basement excavation, top surfaceofplinthfilingjunctionofwallandfloor,alongwiththeexternalperimetreof building, expansion joints surrounding of pipes and conduit etc, complete (plinth area of the building at groundfloor only shall be measured) using Chlorpyriphos/ Lindane emulsifiable concentrate of 20% |
| 5 | HSR ITEM NO.6.1 Providingandlayinginpositioncementconcreteofspecifiedgrade excluding the cost of centering and shuttering - All work below plinth level and upto floor IV level.6.1.61 :4: 8 ( 1 Cement : 4 coarse sand (zone-Ill) : 8 graded cum stone aggregate 40 mm nominal size) |
| 6 | HSRITEMNO.6.8 Providing and laying damp-proof course with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-Ill): 4 graded stone aggregate 12.5mm nominal size)6.8.2 40mm |
| 7 | HSRITEMNO.6.10 Providing & applying a coat of residual petroleum bitumen of sqm grade ofVG-1Oofapprovedqualityusing1.7kgpersquare metreon dampproof courseafter cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil. |
| 8 | HSRITEMNO. 6.13 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth |
| 9 | HSRITEMNO.6.14 Providing and laying in position specified grade of reinforced cementconcrete, excluding the cost of centering, shuttering, finishing and reinforcement-All work up to plinth level:6.14.1 1:1.5:3 ( 1 cement : 1. 5 coarse sand (zone-Ill): graded stone aggregate 20 mm nominalsize) |
| 10 | HSRITEMNO. 6.14.2 1 :2:4 (1 cement : 2coarse sand (zone-Ill) : 4 graded cum stone aggregate 20 mm nominal size) |
| 11 | HSR ITEM NO.6.15Reinforcedcementconcreteworkinwalls(anythickness),including attachedpilasters,buttresses, plinthandstringcourses,fillets,columns,pillars,piers, abutments, posts and struts etc. above plinth level up to floor four level, excluding cost of centering, shuttering, finishing and reinforcement :6.15.1 1:1.5:3 (1 cement : 1.5 coarse sand(zone-111) : 3 cum graded stone aggregate 20 mmnominal size) |
| 12 | HSR ITEM NO.6.16Reinforcedcementconcreteworkinbeams,suspendedfloors,cum roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor four level, excluding the cost of centering, shuttering, finishing and reinforcement with 1: 1.5:3 (1 cement : 1.5 coarse sand(zone-111) : 3 graded stone aggregate 20 mm nominal size). |
| 13 | HSRITEMNO. 6.30Centering and shuttering including strutting, propping etc. and removal of form for6.30.1 Foundations, footings, bases of columns, etc. for mass concrete |
| 14 | HSRITEMNO. 6.30.3 Suspended floors, roofs, landings, balconies and |
| 15 | HSRITEMNO. 6.30.5 Lintels, beams, plinth beams, girders, bressumers and cantilever |
| 16 | HSRITEMNO. 6.30.6 Columns, Pillars, Piers, Abutments, Posts and Struts. |
| 17 | HSRITEMNO. 6.30.7 Stairs, (excluding landings) except spiral-staircases. |
| 18 | HSR ITEM NO.6.30.15Smalllintelsnotexceeding1.5mclearspan,mouldingasin cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like |
| 19 | HSRITEMNO.6.30.16 Edges of slabs and breaks in floors and walls 6.30.16.1 Under 20 cm wide. |
| 20 | HSRITEMNO. 6.30.19 Weather shade, Chajja, corbels etc., including sqm edges |
| 21 | HSRITEMNO. 6.34 Steel reinforcement forR.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending,placinginposition, binding,wastage, overlaps, welded joints,spacer bars,chairs, stays, hangers and annealed steel wire etc. complete in all respect below plinth levelNote:-Reinforcementshallbemeasuredinlengthincludinghooks,ifany,separatelyfor differentdiametersasactuallyusedinwork,excludingoverlaps.Wastage,overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement.6.34.6 Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 22 | HSR ITEM NO.7.21Brickworkwithcommonburntclaynon-modularbricksofclass designation 10.5 in foundation and plinth in:7.21.2 Cement mortar 1:6 (1 cement: 6 coarse sand) |
| 23 | HSR ITEM NO.7.22Brickworkwithcommonburntclaynon-modularbricksofclass designation 10.5 in superstructure above plinth level up to floor IV level in all shapes and sizes in :7.22.2 Cement mortar 1:6 (1 cement: 6 coarse sand) |
| 24 | HSRITEMNO. 7.28 Half brick masonry with common burnt clay non-modular bricks of class designation 10.5 in superstructure above plinth level up to floor IV level.7.28.2 Cement mortar 1 :4 ( 1 cement :4 coarse sand) |
| 25 | HSR ITEM NO.8.26Providingandfixing18mmthickgangsawcut,mirrorpolished,premouldedandprepolished, machinecutforkitchenplatforms,vanitycounters,window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1 :4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.8.26.2 Granite of any colour & shade.8.26.2.2 Area of slab over 0.50 sqm |
| 26 | HSRITEMNO.8.27 Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.8.27.2 Granite work |
| 27 | HSRITEMNO.8.28Extrafor providingopening ofrequired size& shape for washbasin/kitchen sink in kitchen platfonn, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. |
| 28 | HSRITEMNO.9.10 Painting top of roofs with bitumen of approved quality @ 17kg per 10sqm impregnated with a coat of coarse sand at 60 cudm per 10 sqm, including cleaning the slabsurfacewithbrushesandfinallywithapieceofclothlightlysoakedinkeroseneoil complete9.10.1With residual type petroleum bitumen of grade VG -10 |
| 29 | HSRITEMNO.9.11 10 cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa @ 35 kg per cum of earth and gobri leaping with mix 1: 1 (1 clay : 1 cow dung) and covered with flat tilebricks, grouted with cement mortar 1 :3 (1 cement: 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finished neat:9.11.1 With common burnt clay non- modular brick tile of class sqm designation 10 |
| 30 | HSRITEMNO.9.17 Providing gola 75x75 mm in cement concrete 1 :2:4 (1 cement : 2 coarsesand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :9.17.1 In 75x75 mm deep chase |
| 31 | HSR ITEM NO.9.18Makingkhurras45x45cmwithaverageminimumthicknessof5cm cement concrete1 :2:4 (1 cement : 2 coarse sand :4 gradedstone aggregateof 20mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 32 | HSRITEMNO.9.47.2 GI Metal Ceiling Lay in perforated Tegular edge global whitecolour tilesofsize595x595mmand0.5mmthickwith8mmdrop;madeofGIsheethaving galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holesandhavingNRC (NoiseReductionCoefficient)of0.5,electrostaticallypolyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fibre acoustical fleece |
| 33 | HSRITEMNO. 10.1 Providing and laying of base course of floors consisting of 100 mm thick cement 1 :8: 16 and 100 mm sand or stone filling. |
| 34 | HSR ITEM NO.10.3SupplyingandprovidingofTangriRiversandunderfloorincluding watering and compaction in 25 cm layers, dressing etc. complete in all respects. |
| 35 | HSRITEMNO. 10.4 Providing and laying of screed of 50 mm thick cement concrete 1:8:16 to be laid below the topping |
| 36 | HSRITEMNO.10.30 Providing and laying of chequered precast cement concrete tiles 22 mmthick in footpath & courtyard, jointed with neat cement slurry mixedwith pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1 :4 (1 cement: 4 coarse sand).10.30.3Dark shade pigment using ordinary cement. |
| 37 | HSRITEMNO.10.50ProvidingandlayingPolishedGranitestoneflooringinrequired design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cementmortar1:4(1cement:4coarsesand)laidand jointedwithcementslurryand pointingwithwhitecementslurryadmixedwithpigmentofmatchingshadeincluding rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in- Charge.10.50.1PolishedGranitestoneslabjetBlack,CherryRed,EliteBrown, CatEyeorequivalent. |
| 38 | HSR ITEM NO. 10.51Providing and fixing granite stone in all shades 15mm to 18 mm thick in skirting /dado, risers of steps, pillars and wall facing, laid in any pattern as specified over base of 12mm thick cement coarse sand mortar 1 :3 and jointed with white cement slurry mixed withpigmenttomatchtheshadeofGraniteincludinglabourforfixingcrampspinsand dowels etc. |
| 39 | HSRITEMNO.10.58 Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS 15622 : (thickness to be specified by the manufacturer ) of approved make in all colours, shades exceptburgundy,bottlegreen,blackofanysizeasapprovedbyEngineer-in-Chargein skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1 :3 (1 cement: 3 coarsesand)[email protected] white cement mixed with pigment of matching shade complete. |
| 40 | HSRITEMNO.10.63 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4(1cement:4coarsesand),[email protected]/sqmincluding grouting the joints with white cement and matching pigments etc., complete.10.63.2 Size of Tile 600x600 mm |
| 41 | HSR ITEM NO.10.67ProvidingandlayingVitrifiedtilesindifferentsizes(thicknesstobe specified by manufacturer), with water absorption less than 0.08 % andconformingtoI.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1 :3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.10.67.2Size of Tile 600x600 mm |
| 42 | HSRITEMNO.10.70 Extra for grouting the joints of floor tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in- charge. 10.70.2 Size of Tile 600x600 mm |
| 43 | HSRITEMNO. 11.410 mm cement plaster of mix :11.4.2 1 :3 (1 cement: 3 fine sand) |
| 44 | HSRITEMNO. 11.812 mm cement plaster of mix :11.8.21 :6 (1 cement: 6 coarse sand) |
| 45 | HSRITEMNO. 11.9.2 15 mm cement plaster on rough side of single or half brick wall of mix:11.9.2 1 :6 (1 cement: 6 coarse sand) |
| 46 | HSR ITEM NO.11.17 Providingandfixingofchickenwiremeshforavoidingcracksin plaster with necessary nail/screws etc. complete in all respect to the entire satisfaction ofengineer-in-charge |
| 47 | HSRITEMNO.11.54Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. Projection. |
| 48 | HSR ITEM NO.11.58 Providingandapplyingtwocoatswhitecementbasedputtyof approved brand and manufacturer, over plastered surface and grinding the surface smooth with sand paper to get en even and smooth finish including cost and carriage of all material , labour charges, scaffolding, sundries etc. complete. |
| 49 | HSRITEMNO.11.67Apply one coat of water thinable cement primer of approved brand and manufacrture on wall surface: 11.67.1Water thinable cement primer. |
| 50 | HSRITEMNO.11.75Wall painting with premium acrylic emulsion paint of interior grade, having voe (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand andmanufacture,includingapplyingadditionalcoatswhereverrequiredtoachieveeven shade and colour. 11.75.2 Two coats |
| 51 | HSRITEMNO.11.78Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. |
| 52 | HSRITEMNO.11.94 Finishing walls with textured exterior paint of required shade 11.94.1 New work (Two or more coats applied @ 3.28 litre/10 sqm) |
| 53 | HSRITEMNO.11.98Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gmnitre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives.11.98.1Newwork([email protected]/10sqmOverandincluding priming coat of exterior primer applied @ 0.90 litre/10 sqm |
| 54 | HSRITEMNO.12.33 Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complet.12.33.2 With 12 mm mild steel U beading |
| 55 | HSRITEMNO. 12.37 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:12.37.1 35 mm thick including ISi marked Stainless Steel butt hinges with necessary screw |
| 56 | HSRITEMNO.12.12 Providing & Fixing decorative high pressure laminated sheet of plain/ wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 12.12.21.0 mm thick |
| 57 | HSRITEMNO.12.15Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters.(Area of opening for glass panes excluding portion inside rebate shall be measured). |
| 58 | HSRITEMNO.12.49 Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets:12.49.2 25 mm dia (heavy type) |
| 59 | HSRITEMNO.12.50 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.HSRITEMNO.12.50.2 Fixed to openings/Wooden frames with rawl plugs screws etc. |
| 60 | HSRITEMNO.12.89 Providing and fixing aluminium e xtruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS: 3564, embossed on the body, door weight up to 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. |
| 61 | HSRITEMNO. 12.98 Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :12.98.1 300x16 mm |
| 62 | HSRITEMNO. 12.99 Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete. 12.99.2 250x10 mm |
| 63 | 12.99.4 150x 10 mm |
| 64 | HSRITEMNO. 12.102 Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 1 O as per IS : 1868) transparent or dyed torequired colour or shade, with necessary screws etc. complete.12.102.1 125 mm |
| 65 | HSRITEMNO. 12.102 Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 1 O as per IS : 1868) transparent or dyed torequired colour or shade, with necessary screws etc. complete.12.102.2 100 mm |
| 66 | HSR ITEM NO.12.103Providingandfixingaluminiumhangingfloordoorstopper,ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.12.103.2 Twin rubber stopper |
| 67 | HSR ITEM NO.12.118.2 30mmthickfactory madePolyvinyl Chloride(PVC) doorshutter sqm made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm(:± 0.2 mm),with inbuilt decorative mouldingedgingon oneside. Thestyles andrails mitred and joint at the comers by means of M.S. galvanised/ plastic brackets of size 75x220 mmhavingwallthickness1.0mmandstainlesssteelscrews.Thestylesoftheshutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (:± 0.1mm) wall thickness.The lock rail made up of \"H\" section, a uPVC hollow section of size 100x30 mm and 2 mm (:±0.2 mm)wall thickness fixed to the shutter styles by meansof plastic/ galvanised M.S.\"U\" cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (:± 0.1 mm) wall thickness . The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod andfastenecompleteaspermanufacturer\"sspecificationanddirectionofEngineer-in- |
| 68 | HSRITEMNO. 12.119 Providing and fixing factory made P.V.C. door frame of size 50x47 mm withametrewallthicknessof5mm,madeoutofextruded5mmrigidPVCfoamsheet, mitred at comers and joined with 2 Nos. of 150 mm long brackets of 15x15 mmM.S.squaretube,theverticaldoorframeprofilestobereinforcedwith19x19mmM.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, completeas per manufacturer\"s specification and direction of Engineer- in- Charge |
| 69 | HSRITEMNO. 12.157 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and othersectionsofapprovedmakeconformingtoIS:733andIS:1285,fixingwithdash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shallbesmooth,rustfree,straight,mitredandjointedmechanicallywhereverrequired including cleat angle, Aluminiumsnap beading for glazing/ panelling, C.P. brass / stainless steelscrews,allcompleteasperarchitectural drawingsandthedirections ofEngineer-in- charge. (Glazing, panelling and dash fasteners to be paid for separately) :12.157.1 For fixed portion 12.157.1.2 Powder coated aluminium(minimumthickness ofpowder coating 50 micron) |
| 70 | HSR ITEM NO. 12.157.2 For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)12.157.2.2Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 71 | HSRITEMNO.12.158.2Providing and fixing 12 mm thick prelaminated particle board flatpressed three layer or graded wood particle board conforming to IS: 12823 Grade I Type II, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer- in-charge.Pre-laminated particle board with decorative lamination on both sides |
| 72 | HSR ITEM NO.12.159Providingandfixingglazinginaluminiumdoor,window,ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architecturaldrawingsandthedirectionsofengineer-in-charge.(Costofaluminiumsnap beading shall be paid in basic item):12.159.2 With float glass panes of 5.0 mm thickness (weight not less than 12.50 kg/sqm) |
| 73 | HSRITEMNO.12.160 Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight up to 125 kg, for doors, including cost of cutting floors, embedding in floors as required and makinggood the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.12.160.1 With stainless steel cover plate minimum 1.25 mm thickness |
| 74 | HSRITEMNO.13.4Providing and fixingM.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of requiredsize, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. 13.4.1 Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) |
| 75 | HSR ITEM NO.13.29.2Steelworkweldedinbuiltupsections/framedwork,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. |
| 76 | HSRITEMNO.13.35Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer. |
| 77 | HSRITEMNO.13.41 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes,channels,platesetc.,includingwelding,grinding,buffing,polishingandmaking curvature (wherever required) and fitting the same with necessary stainlesssteel nuts and boltscomplete,i/cfixingtherailingwithnecessaryaccessories&stainlesssteeldash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slabwith suitable arrangement asper approvalof Engineer-in- charge, (forpayment purposeonlyweight ofstainlesssteelmembers shallbeconsideredexcluding fixing accessories such as nuts, bolts, fasteners etc.) |
| 78 | HSRITEMNO.30.82 Making holes by cutting cores of appropriate dia in RCC floors and roofs of thickness up to 6\" (six inches) for passing drain pipe and repairing the hole after insertion of drain pipe etc. including finishing-complete so as to make it leak proof. 30.82.1 Drain pipe of 150mm internal dia |
| 79 | HSRITEMNO.30.82.2Drain pipe of 100mm internal dia |
| 80 | NSProviding & Fixing aluminium fittings for door and windows shutters with stainless steel or C.P brass screws of required size complete.FoldingHandle 100mm |
| 81 | PUBLIC HEALTH WORKS:-HSRITEM4.16Excavatingtrenchesofrequiredwidthforpipes,cables,etcincluding excavationforsockets,anddressingofsides,rammingofbottoms,depthupto1.5m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding20cmindepth,includingconsolidatingeachdepositedlayerbyramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m:4.16.1 All kind of soil 4.16.1.2 Pipes, cables etc. exceeding 80 mm metre dia. but not exceeding 300 mm dia. |
| 82 | HSR ITEM 6.1 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level:HSR ITEM 6.1.7 1:5:10 (1 cement : 5 coarse sand (zone-Ill): 10 graded stone aggregate 40 mm nominal size) |
| 83 | HSR ITEM 6.1 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level:HSR ITEM 6.1.2 1:2:4 (1 cement : 2 coarse sand (zone-Ill) : 4 graded stone aggregate 20 mm nominal size) |
| 84 | HSRITEM6.16Reinforcedcementconcreteworkinbeams,suspendedfloors,cumroofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor four level, excluding the cost of centering,shuttering,finishingand reinforcementwith1:1.5:3(1cement:1.5coarse sand(zone-111) : 3 graded stone aggregate 20 mm nominal size). |
| 85 | HSR ITEM 6.33 Steel reinforcement for R.C.C. work, wherenot includedin thecomplete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps,weldedjoints,spacerbars,chairs,stays,hangersandannealedsteelwireetc. complete in all respect below plinth level:Note:-Reinforcementshallbemeasuredinlengthincludinghooks,ifany,separatelyfor differentdiametersasactuallyusedinwork,excludingoverlaps.Wastage,overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement.6.33.6 Thermo-Mechanically Treated bars of grade Fe-500D kg or more. |
| 86 | HSR ITEM 7.21 Brick work with common burnt clay non-modular bricks of class designation 10.5 in foundation and plinth in:7.21.1Cement mortar 1:4 (1 cement: 4 coarse sand) |
| 87 | HSR ITEM 9.57 Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conformingto IS : 13592Type A, including jointingwith seal ringconformingto IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 9.57.2110 mm diameter |
| 88 | HSR ITEM 9.57Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conformingto IS : 13592Type A, including jointingwith seal ringconformingto IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 9.57.3150 mm diameter |
| 89 | HSRITEM9.58ProvidingandfixingonwallfaceUnplasticised-PVCmouldedfittings/ accessories forUnplasticised RigidPVC rainwaterpipesconformingtoIS:13592TypeA, includingjointingwithseal ring conformingtoIS:5382,leaving1Ommgapforthermal expansion.9.58.2 Single pushfit CouplerHSR ITEM 9.58.2.1 75 mm |
| 90 | HSR ITEM 9.58.2.2 Single pushfit Coupler 110 mm |
| 91 | HSR ITEM 9.58.3.1 Single tee with door 75x75x75 mm |
| 92 | HSR ITEM 9.58.3.2Single tee with door 110x110x110 mm |
| 93 | HSR ITEM 9.58.4.1Single tee without door 75x75x75 mm |
| 94 | HSR ITEM 9.58.4.2Single tee without door 110x110x110 mm |
| 95 | HSR ITEM 9.58.5.1Bend 87.5° 75 mm bend |
| 96 | HSR ITEM 9.58.5.2Bend 87.5° 110 mm bend |
| 97 | HSR ITEM 9.58.6.1Shoe (Plain) 75 mm |
| 98 | HSR ITEM 9.58.6.2Shoe (Plain) 110 mm |
| 99 | HSR ITEM 10.14Providing a floating coat of 1.50 mm thick neat cement laid in one operation to the topping. |
| 100 | HSR ITEM 11.1.1 6 mm cement plaster of mix: 1 :3 (1 cement : 3 fine sand) |
| 101 | HSR ITEM 11.5.1 12 mm cement plaster of mix : 1 :2 (1 cement: 2 fine sand) |
| 102 | HSR ITEM 11.52 Cement rendering on plaster 1 mm thick |
| 103 | HSR ITEM 20.25 Cutting holes up to 23 cm square through brick work in mud walls for pipes and making good induding repointing, replastering and finishing according to existing finish where required.20.25.1 11.43 cm thick wall |
| 104 | HSR ITEM 20.25.2 22.86 cm thick wall |
| 105 | HSR ITEM 21.28Providing & fixing steel bar embedded plastic steps of size 263mm x 165mmoforangecolour,confirmingtospecificationinpumpchambers,manholesetc.,having minimum 3mm thick polypropylene polymer confirming to is:10910 encapsulated on 12mm dia ribbed steel bars per IS : 1786. The rate include cost of setting the same to correct lines and levels duly embedded in 1 :2:4 cement concrete including carriage, loading, uploading, stacking, handling, re-handling etc., complete in all respect to the satisfaction of Engineer-in- charge |
| 106 | HSR ITEM 21.57 Providing masonry plugs to ends of sewers of all types with 11.43 cmthick brick wall in cement sand mortar 1 :7 with 12 mm thick cement plaster 1: 6 (as required by the engineer-in-charge).21.57.1 For Circular Sewers having internal dia meter.21.57.1.2 150 mm |
| 107 | HSR ITEM 21.84 Constructing brick masonry inspection Chamber sizes as given below up to0.60 metre average depth in cement mortar 1 :5 lime concrete with 40 per cent lime mortar 2:3 in foundation cement concrete 1 :2:4 benching 12mm thick cement plaster 1 :2 with a floating coat of 1 mm thick of neat cement R.C.C. 1 :2:4 slab 100 mm thick/cement concrete topping, 50mm thick: with 455mmx455mm / 455mm x610mm inside light duty C.I. inspection chambercoverandframeweightasper1.5.1.specification paintedwith3coats ofblack bitumastic superior paint complete as per standard design.21.84.1 Size 450 mm X450 mm inside (with 455 mm x 455 mm coverand frame light duty single seal weighing 20 kg with C.C. topping |
| 108 | HSR ITEM 21.84.2 Size 450 mm X 600 mm inside (with 455 mm x 610 mm cover and framesingle seal pattern I weighing 38 kg with C.C. topping) |
| 109 | HSR ITEM 21.85 Extra for every 0.30 metre depth of Inspection chamber21.85.1 450 mm x 450 mm inside |
| 110 | HSR ITEM 21.85.2 450 mmx 600 mm inside |
| 111 | HSR ITEM 21.93 Providing and fixing SFRC MANHOLE COVERS AND FRAMES MARKED WITHIS: 12592 including setting the same to correct lines and levels in 1 :3 cement sand mortar over manhole including carriageloading unloading stacking handling re-handling etc. complete in all respects to the satisfaction to the Engineer-in-charge.HSR ITEM 21.93.2 Type:- Extra Heavy Duty Set (EHD-20) 560MM Clear Opening |
| 112 | HSRITEM22.6.2ProvidingandfixingwhitevitreouschinawarelaboratorysinkwithC.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required: Size 600x450x200 mm |
| 113 | HSRITEM22.10ProvidingandfixingStainlessSteelAISI304(18/8)kitchensinkasper IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever requiredHSR ITEM 22.10.1.3 510x1040 mm bowl depth 200 mm |
| 114 | HSR ITEM 22.16 Providing and fixing 40mm i/d G.I. waste pipe embedded in walls up to floor level including cost of union and plumber joint |
| 115 | HSRITEM22.20ProvidingandfixinginpositionC.I. plainNahani TrapconformingtoI.S.I. specifications and of self cleaning design with C.P. brass hinged grating with frame complete. HSR ITEM 22.20.2 With 75 mm internal diameter outlet |
| 116 | HSR ITEM 22.22 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittingsandfixturescomplete,includingcuttingandmakinggoodthewallsandfloors wherever required:HSRITEM22.22.1WhitevitreouschinawareOrissapattern W.C. pan ofsize 580x440mmwith integral type foot rests |
| 117 | HSR ITEM 22.33 Providing and fixing white vitreous chinaware extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous chinawarecistern/PVCcistern(withbrassfitting) intothewallwithdualflushfitting,of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. |
| 118 | HSR ITEM 22.38 Providing and fixing 8 mm dia C.P. I S.S. Jet with flexible tube up to 1 metrelongwithS.S. triangularplate to Europeantype W.C. of qualityand makeas approvedby Engineer - in - charge. |
| 119 | HSR ITEM 22.42 Providing and fixing toilet paper holder 22.42.1C.P. brass |
| 120 | HSR ITEM 22.49 Providing and fixing in position best Indian make Whitevitreous chinaware channelofsize600mmx150mmincludinglayingandfixingincementconcrete1:2:4 complete as required by the Engineer-in-charge.22.49.1 White |
| 121 | HSR ITEM22.53 Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4mix(1cement:2coarsesand:4gradedstoneaggregate20mmnominalsize), including cost of cutting holes and making good the walls etc. :22.53.1 For 100 mm dia pipe |
| 122 | HSR ITEM 22.53.2 For 75 mm dia pipe |
| 123 | HSRITEM22.80Providingandfixingtrapofselfcleansingdesignwithscreweddownor hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors22.80.2100mminlet and 75 mm Outlet.HSR ITEM 22.80.2.1 Sand cast iron S&S as per IS - 3989 |
| 124 | HSR ITEM 22.85ProvidingandfixingChlorinatedPolyvinylChloride(CPVC)pipes,having thermalstabilityforhot&coldwatersupply,includingallCPVCplain&brassthreaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.22.85.3 25 mm dia nominal bore |
| 125 | HSR ITEM 22.85.4 32 mm dia nominal bore |
| 126 | HSR ITEM 22.86ProvidingandfixingChlorinatedPolyvinylChloride(CPVC)pipes,having thermalstabilityforhot&coldwatersupply,includingallCPVCplain&brassthreaded fittings, i/c fixing the pipe with clamps at 1.00 mspacing. This includes jointingof pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 22.86.2 20 mm dia nominal bore |
| 127 | HSR ITEM 22.86.3 25 mm dia nominal bore |
| 128 | HSR ITEM 22.86.4 32 mm dia nominal bore |
| 129 | HSR ITEM 22.91 Providing and fixing G.I. pipes complete with G.I. fittings including trenchingup to 0.30m to 1.00m depth and refilling etc.HSR ITEM 22.91.6 50 mm dia nominal bore |
| 130 | HSR ITEM 22.93 Providing and filling sand envelope of grading zone grade, 100mm all-roundthe G.I. pipes in external work: 22.93.650mm diameter pipe |
| 131 | HSRITEM22.103 Providingandfixingballvalve(brass)ofapprovedquality,Highorlow pressure, with plastic floats complete :HSR ITEM 22.103.325 mm nominal bore |
| 132 | HSR ITEM 11.107 Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work11.107.3 25 mm diameter pipe |
| 133 | HSR ITEM 11.107.5 40 mm diameter pipe |
| 134 | HSRITEM22.109ProvidingandfixingC.P.Brassextensionnipple(size15mmx50mm)of approved make and quality as per direction of Engineer-in-charge. |
| 135 | HSR ITEM 22.128.1 Providing and fixing Unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour.:15 mm nominal bore with 30cm length |
| 136 | HSR ITEM 22.128.2 15 mm nominal bore with 45 cm length |
| 137 | HSR ITEM 22.166 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:HSR 22.166.2 150 x100 mmsize Ptype With common burnt claynon- modular bricks of class designation 10.5 |
| 138 | HSR ITEM 22.181 Providing and placing on terrace (at all floor levels) polyethylene waterstorage tank, IS: 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 139 | HSR ITEM 22.212 Providing and fixing in position best Indian make coat and hat hooks fixed into wall with C.P. brass screws and rawl plugs etc. complete including cutting and making good the walls etc.22.212.1 C.P. Brass(HSR 22.212.1.1) One Way |
| 140 | HSR ITEM 22.221 Providing and fixing in position vitreous chinaware white lavatory suites ofapprovedmake(totheapprovalofEngineer-in-charge)includingRackBoltScrewPair 115mm long without CP fittings complete in all respect.22.221.9 Size 560mm x 450mm (Under counter oval) |
| 141 | HSR ITEM 22.222ProvidingandfixinginpositionsingelsocketSWRUPVCsoilwasteor antisyphonagepipesasperIS13592ofE.D.Cmanufactureorofanyotherreputedfirm including cutting, jointing, wastage, but excluding cost of jointing.Single Socket Type B.22.222.1 160mm old SWR UPVC pipe lines laid complete |
| 142 | HSR ITEM 22.222.2 110mm old SWR UPVC pipe lines laid complete |
| 143 | HSR ITEM 22.222.4 75 mm, Soil & Waste Pipe |
| 144 | NS Providing and fixing CPVC Union in CPVC pipe including cutting and pasting the pipe andmaking long screws etc. complete (New work) : 20 mm nominal bore |
| 145 | NS Providing and fixing CPVC Union in CPVC pipe including cutting and pasting the pipe and making long screws etc. complete (New work) :25 mm nominal bore |
| 146 | NS Providing and fixing CPVC Union in CPVC pipe including cutting and pasting the pipe andmaking long screws etc. complete (New work): 40 mm nominal bore |
| 147 | NSProvidingandfixingCPVCgatevalveofapprovedqualityasperthesatisfactionofengineer in charge.20 mm nominal bore |
| 148 | NSProvidingandfixingCPVCgatevalveofapprovedqualityasperthesatisfactionofengineer in charge.25 mm nominal bore |
| 149 | NSProvidingandfixingCPVCgatevalveofapprovedqualityasperthesatisfactionof engineer in charge.32 mm nominal bore |
| 150 | NS Providing and fixing UPVC Floor Trap 110 mm dia |
| 151 | NS Providing and fixing UPVC P-Trap 110 mm dia |
| 152 | NS Providing and fixing C.P. Brass Angle Valve of approved design & quality, Quarter Turn 15 mm nominal bore, Make Jaquar OR Equivalent as per the satisfaction of Engineer in Charge |
| 153 | NS Providing & fixing CP brass pillar cock of approved design & quality, Quarter Turn 15 mm nominal bore, Make Jaquar OR Equivalent as per the satisfaction of Engineer in Charge |
| 154 | NS Providing & fixing CP brass Long Body Bib cock of approved design & quality, Quarter Turn15mmnominalbore,MakeJaquarOREquivalentasperthesatisfactionofEngineerin Charge. |
| 155 | NS Providing & fixing CP brass short Body Bib cock of approved design & quality, Quarter Turn15mmnominalbore,MakeJaquarOREquivalentasperthesatisfactionofEngineerin Charge. |
| 156 | NS Providing & fixing CP brass Laboratory cock swan neck (one way) of approved design &quality, Quarter Turn 15 mm nominal bore, Make Jaquar OR Equivalent as per the satisfaction of Engineer in Charge. |
| 157 | NS Providing and fixing CP Brass towel ring of approved design & quality. Make Jaquar OREquivalent as per the satisfaction of Engineer in Charge. |
| 158 | NS Providing and fixing CP Grating (circular type) 100 mm dia of approved quality. |
| 159 | NS Providing and fixing CP Brass Soap Dish Holder of approved design & quality. Make Jaquar OR Equivalent as per the satisfaction of Engineer in Charge. |
| 160 | NSProvidingandfixingC.P.brassstopcock(concealed)ofapprovedqualityanddesign.QuarterTurn15mmnominalbore,MakeJaquarOREquivalentasperthesatisfaction of Engineer in Charge. |
| 161 | NS Providing and fixing white vitreous chinaware flat back half stall urinal of size 580x380x350 mm with white PVC flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS: 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cuttingandmakinggoodthewallsandfloorswhereverrequired:Rangeoftwohalfstall urinals (without 5 litre P.V.C. automatic flushing cistern) |
| 162 | NS Providing and fixing white vitreous chinaware flat back half stall urinal of size 580x380x350 mm with white PVC flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS: 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting andmakinggoodthe wallsand floorswherever required:Range ofthree half stall urinals (without 10 litre P.V.C. automatic flushing cistern) |
| 163 | NSProviding and fixing5 mmthick fancylooking mirror( Saintgobin/modiguard)bevelled edges fixed directly on finished wall with SS Studs & 750 C/c max. distance horizontaly on top & bottom ( of approved quality) and of required shape and size as per the drawing complete in all respect to the satisfaction of Engineer in Charge. |
| 164 | NSExtraforusingDoublechargedVitrifiedTilesofapproveddesign&makehavingsize 600*600mminplaceofsinglechargedVitrifiedTiles.makeDACIAGreenofSomanyor equivalent. |
| 165 | NS Providing and Filling Brick bats in Soak pit by mechanical/ manual means. |
| 166 | NSProvidingandfixing3MMThickACP Sheet (Aluminiumcompositepanel) False Ceiling overframeofaluminiumpipesetcincludingthecostofACP,Aluminiumpipe,silicon, necessary screws etc all complete as per direction of Engineer-in charge. |
| 167 | ELECTRICAL WORKS:-HSR ITEM 23.4.1 Wiring for Light/Fan/call bell point with modular type switch/socket and GIbox, Modular type face plate etc in 1.5 sqmm FRLS PVC insulated copper conductor cable in1.6 mm thick PVC conduit pipe.23.4.1.3 Group C |
| 168 | HSR ITEM 23.4.2 Wiring for Twin control light point with 2 nos , 2-ways, 5 amp. Modularswitch GI box and modular face plate in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe.23.4.2.3 Group C |
| 169 | HSR ITEM 23.4.3 Wiring for Light/Fan/call bell point in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe, without separate control switch.23.4.3.3 Group C |
| 170 | HSR ITEM 23.4.4 Wiring in PVC conduit system for 3-pin 5amp. Plug point by using 2 no 1.5 sqmm FRLS copper wire and 1 no 1.5 Sqmm FRLS copper wire , including providing 1 no 5/6 Amp 3/5 pin Modular type socket and 1 no 5/6 Amp Modular type switch required GI Box, modular face plate etc complete as required.23.4.4.3 Group C |
| 171 | HSR ITEM23.4.5 Wiring in PVC conduit system for 3-pin 15amp. Plug point by using 2 no 4 sqmm FRLS copper wire and 1 no 4 Sqmm FRLS copper wire for earthling , including providing 1 no 15/16 Amp 3/6 pin Modular socket and 1 no 15/16 Amp Modular switch required GI Box, modular face plate etc complete as required23.4.5.3 Group C |
| 172 | HSR ITEM 23.3.6 Wiring main and sub mains in two single core for phase and neutral wireand one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in PVC Conduit etc as required.23.3.6.9 3 run of Size 1.50 Sqmm(1/1.40mm) |
| 173 | HSR ITEM 23.3.6.10 3 run of Size 2.50 Sqmm(1.1.80mm) from DB to Switchboards |
| 174 | DSR 1.14 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.1.14.104 X 10 sq. mm + 2 X 6 sq. mm earth wire |
| 175 | DSR 1.14.11 4X 16 sq. mm + 2 X 6 sq. mm earth wire |
| 176 | HSR ITEM 23.7.6 Supply and erection of PVC CONDUIT ISImarked (Medium) recessed inwalVceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work. 23.7.6.1 PVC pipe of 20 mm dia. |
| 177 | HSR ITEM 23.7.6.2 PVC pipe of 25 mm dia. |
| 178 | HSR ITEM 23.7.6.3 PVC pipe of 32 mm dia. |
| 179 | HSR ITEM 23.7.6.4 PVC pipe of 40 mm dia. |
| 180 | HSR ITEM 23.8.10 Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects.23.8.10.1 1 & 2 Modules including combined plate for Telephone and data |
| 181 | HSR ITEM 23.8.10.2 3 Modules |
| 182 | HSR ITEM 23.8.10.4 6 Modules |
| 183 | HSR ITEM 23.8.11 Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect.23.8.11.7 step type Fan Regulator 2 modules 300 watt |
| 184 | HSR ITEM 23.8.11.8 Telephone Socket outlet modular type |
| 185 | HSR ITEM 23.8.11.11 RJ 45 Computer DATA socket outlet for CAT 6 or CAT6e cable Modulartype |
| 186 | HSR ITEM 23.8.4 Supply and erection of 10.5 cm dia M.S.Fan box including 8 mm dia 30 cm each 106 long M.S. Road made into suitable suspension hook and erected in R.C.C. slab for the erection of fan complete with all labour and material required to complete the job. |
| 187 | HSR ITEM 23.23.10 Supplying and drawing of 1 no UTP 4 pair CAT Sa LAN Cable in the existing surface/recess MS/PVC conduit as required |
| 188 | HSR ITEM 23.22.4 Supply and erection of double door sheet steel enclosure distributionboard suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work.23.22.4.6 TPN DB Horizontal type Double Door 6 way ( 8 incoming 3phase*6outgoing) |
| 189 | HSR ITEM 23.22.4.7TPN DB Horizontal type Double Door 8 way ( 8 incoming 3phase*8outgoing) |
| 190 | HSR ITEM 23.22.5 Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 23.22.5.1 6 amp. to 32 amp Single Pole |
| 191 | HSR ITEM 23.22.5.6 40 amp to 63 amp. MCB\"s Triple POLE |
| 192 | HSR ITEM 23.22.5.8 40 amp to 63 amp. MCB\"s FOUR POLE |
| 193 | HSR ITEM 23.22.6 Supply and erection double pole/Four pole Residual (RCCB/ELCB) on 240/415V, 5Hz. AC supply installed in existing sheet steel enclosures including making necessarynnections and bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work.23.22.6.2DP RCCB 30ma sensitivity , 40 A |
| 194 | HSR ITEM 23.22.6.3 DP RCCB 30ma sensitivity , 63 A |
| 195 | HSR ITEM 23.22.7 Supply and erection of blanking sheet in existing distribution board. |
| 196 | HSR ITEM 23.22.1 Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in- charge of the work.23.22.1.9 4 pole MCCB 6 amp to 100 amp , 25 KA |
| 197 | HSR ITEM 20.71SUPPLY & ERECTION OF LIGHT AND FAN FIXTURES Supply, erection, testing of Ceiling fans IS marked (as per IS code 374) with suitable GI pipe complete in all respects complete as per directions of Engineer-in-charge. 20.71.148\" (1200mm) |
| 198 | HSR ITEM 20.72 Supplying, errection, testing of Exhaust fan (as per IS code 374) having a capacity of 45 cubic metre per minute complete with suitable G.I sheet ducting in structure confirming to latest IS specifications complete in all respect to satisfaction of Engineer-in- charge. |
| 199 | HSR ITEM 23.20 Fixing of LED Tube light/ 2*2 ft square panel fitting directly on wall /ceiling or false ceiling including making connections etc as required |
| 200 | HSR ITEM 23.21 Fixing of LED Down lighter 7 to 28 Watt on ceiling or in false ceiling including cutting/making hole in ceiling including making connections etc as required. |
| 201 | HSR ITEM 24.1.3 Earthing with G.I. earth plate 600 mmx 600 mm x 6 mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) complete as required. |
| 202 | HSR ITEM 24.1.5 Extra for charcoal or coke and salt for G. I. plate or copper plate earthelectrode. |
| 203 | HSR ITEM 24.1.6 Supplying and laying 25mm x 3mm G.I. strip at 0.5 metre below ground asstrip earth electrode including soldering etc. as required. |
| 204 | HSR ITEM 24.1.7 Supplying and laying 25mm x 3 mm G.I. strip in 40 mm dia,GI pipe as/fromearth electrode including soldering etc. as required. |
| 205 | HSR ITEM 24.1.8 Providing and fixing 25 mm x 3mm G.I. strip on surface or in recess forconnections etc. as required with all labour and material. |
| 206 | HSR ITEM 24.1.14 Supply and erection of 20mm x 3 mm thick GI, tape fixed with suitable G.I.staples of same size. |
| 207 | HSR ITEM 24.1.17 Providing and fixing testing joints made of 20mm x 3mm thick G.I. strips125 mm long with 4 nos. G.I. bolts and nuts with washers complete |
| 208 | DSR 6.14 Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required. |
| 209 | HSR ITEM 24.2.2 Laying of underground cable 0. 75 metre below ground level covered withsand and bricks including excavation and refilling of trenches.:-24.2.2.3 50 Sq mm to 150 sqmm 2 to 4 Core |
| 210 | HSR ITEM 24.2.4 Laying of underground cable in pipe /existing open/closed trench etc as24.2.4.3 50 Sq mm to 150 sqmm 2 to 4 Core |
| 211 | HSR ITEM 24.2.5 Laying and fixing of cable on surface/ cable tray etc as required:-24.2.5.1 2.5 Sq mm to 10 Sq mm 2 to 4 Core |
| 212 | HSR ITEM 24.2.5.2 16 Sq mm to 35 sqmm 2 to 4 Core |
| 213 | HSR ITEM 24.2.5.3 50 Sq mm to 150 sqmm 2 to 4 Core |
| 214 | HSR ITEM 24.2.7 Supply and erection of suitable compression type brass cable glands for underground Cable :- 24.2.7.2 10 sqmm to 16s qmm Cable 2 to 4 Core |
| 215 | HSR ITEM 24.2.7.3 25 sqmm to 50 sqmm Cable 2 to 4 Core |
| 216 | HSR ITEM 24.2.7.4 70 sqmm to 95 sqmm Cable 3 to 3½ Core |
| 217 | HSR ITEM24.2.8 Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work 24.2.8.3 10 sqmm |
| 218 | HSR ITEM 24.2.8.4 16 sqmm |
| 219 | HSR ITEM 24.2.8.5 25 sqmm |
| 220 | HSR ITEM 24.2.8.7 50 sqmm |
| 221 | HSR ITEM 24.2.8.9 95 sqmm |
| 222 | HSR ITEM 24.2.10 Supply and erection of cable route marker made of 50 cm long 1 O mm dia M.S. Rod welded/riveted at the top with 1 cm dia 3 mm thick MS plate inscribed with \"cable\" word on it, having a cross arm 30 cm long of the same dia welded at the bottom, in exiting trench 45 cm below ground level. |
| 223 | HSR ITEM 23.23.6 Supply and erection of MS cable tray , duly pained as required including erection of the same on wall or ceiling with necessary fixture and other material required to complete the job in all respect up to the entire satisfaction of Engineer-in Charge of the work.23.23.6.1 MS perforated cable tray painted with powder coating 100 X 5 X 2 mm |
| 224 | HSR ITEM 23.23.6.2 MS perforated cable tray painted with powder coating 200 X 5 X 2 mm |
| 225 | HSR ITEM 23.23.6.3 MS perforated cable tray painted with powder coating 375 X 5 X 2 mm |
| 226 | HSR ITEM 23.26.1 Supply and erection of Medium Voltage caution notice plate of size200*150 each 85 mm in three languages. |
| 227 | HSR ITEM 23.26.3 Supply and erection of shock restoration chart in glass frame. |
| 228 | HSR ITEM 23.26.4 Supply & Erection of mild steel bucket stand suitable for 6 Nos. firebuckets,(but without bucket) including the cost of welding and painting of complete stand will one coat of red oxide and 2 coats of approved paint of red colour with all labour and material required to complete the job in all respect up to the entire Satisfaction engineer in charge of the work (size 6\"x4\" made of GI pipe 32mm dia). |
| 229 | DSR 17.2.1 Supplying, installation, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting not less than 240 devices (including detectors) and minimum 120 detectors per loop and loop length up to 2 km, network communication card,minimum 320 character graphics/ LCD display with touch screen or other keypad and minimum 4000 events history log in the non volatile memory (EPROM), power supply unit (230 ± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free batteries with automatic charger. The panel shall have facility to connect printer to printout log and facility to have seamless integration with analog/digital voice evacuation system (which is part of the schedule of work under SH: PA System) and shall be complete with all accessories . The panel shall be compatible for IBMS system with open protocol BACnet/ Modbus over IP complete asper specifications.17.2.1.2Two Loop Panel. |
| 230 | DSR 17.1.2 Supplying, installation, testing & commissioning of smoke detector with builtinLED and mounting base complete with all connections etc. as required. |
| 231 | DSR 17.2.5 Supplying, installation, testing & commissioning of response indicator onsurface/recessed MS Box having two LED,metallic cover complete with all connections etc as required. |
| 232 | DSR 17.2.7 Supplying, installation, testing & commissioning of fault isolator complete withbase as required. |
| 233 | DSR 17.2.10 Supplying, installation, testing & commissioning of addressable fire controlmodule complete as required. |
| 234 | DSR 17.2.14 Supplying, installation, testing & commissioning of addressable manual call pointcomplete as required. |
| 235 | DSR 17.2.15 Supplying, installation, testing & commissioning of addressable horn cum strobecomplete as required. |
| 236 | DSR 17.1.1 Supplying, installation, testing & commissioning of heatdetector operating at 54ºC/57ºC with rate of rise cum fixed temperature (dual thermistor) type with mounting base complete with all connection etc. as required. |
| 237 | DSR 17.3.1Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required. |
| 238 | DSR 17.3.2 Supplying, installation, testing & commissioning of 6W ceiling speaker completeas required. |
| 239 | DSR 17.3.6 Supplying, installation, testing & commissioning of digital audio amplifier 50Watt, 25V rms operating at 240 volt AC supply complete as required. |
| 240 | DSR 17.3.9 Supplying, installation, testing & commissioning of Voice command keypad 6zone, with microphone assembly complete as required. |
| 241 | DSR 17.5.2 Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outersheath complete as required. |
| 242 | DSR 17.5.3 Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. 17.5.3.1 speaker cable Single pair, 2-core, 1.5 sqmm |
| 243 | DSR 17.5.3.1 speaker cable Single pair, 2-core, 1.5 sqmm |
| 244 | NS SITC of 1.5Ton capacity split type air conditioner fitted with rotary compressor complete with required asserories with remote control system having Auto restart facility. The air conditioner dispatched with 3 MT copper refrigent pipe as per company term and condition etc.Make:- Hitachi,Daikin, O Genral. |
| 245 | NS Supply of Automatic Voltage Stabilizer 5KVA Make Blue bird/Blue Guard/ V Guard |
| 246 | NS Supply of wall mounted MS stand for outdoor unit AC |
| 247 | NS Supply of Copper pipe with insulation Met tub/ Man dev/ Max Flow |
| 248 | NS Supply of Copper wire 2.5mm (3 core) ISI marked Make Polycab/Havells |
| 249 | NS Supply of PVC drain pipe with insulation UPVC Polypack/Prince/Prakesh |
| 250 | NS Supply of Flexible pipe2\" white |
| 251 | NS Supplying of following sizes of 1.1 KV grade multicorealuminium conductor XLPEinsulated armoured cable conforming to IS:7098 (Part - I) complete with all amendments etc. as required 4Cx10 |
| 252 | NS 4Cx16 |
| 253 | NS 4Cx25 |
| 254 | NS 3.5Cx50 |
| 255 | NS 3.5Cx95 |
| 256 | NS Supply of 18 W linear 4ft LED integrated batten made of ultra slim co-extruded polycarbonate channel with housing part in white finish & diffuser part in reeded opal finish.White finish ABS end caps with decorative circular coloured polycarbonate cap snap fitted on the end cap to enhance the aesthetic of the fixture. These end caps are snap-fitted to the fixture.High efficiency long life LED with lumen efficacy of 130 lm/W with viewing angle of 120º.Powered by an integral isolated low THD electronic LED driver ( SMPS based constant current supply) with output short circuit protection, surge protection.Can be fixed directlyinto the wall/ ceiling by means of mounting SS clips provided with the fixture. Lumen Output of 2110 lumens with System efficacy of >105lm/W .CRI >80, Color temperature 6500K, THD<20% and PF>0.95,IP20 . Life class of 35,000 hrs @ L70, Operating Temperature:-10 TO +45DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ. |
| 257 | NS Supply of lighting fixtures of surface mounted 18W edgelit LED Round Downlighterluminaire.The LED source used shall be complying with LM80 standards & LED source efficacy >120 lm/w. Epoxy white powder coated die cast aluminium housing; Efficient PMMA front visor;. The system lumen output of the luminaireof a minimum of 90 lms/W system efficacy with color temprature of 5700 deg K (ANSI Bin) and CRI>80. Integral Driver with constant current constant voltage (CVCC), P.F >0.9, THD<20% and Surge Protection of atleast 2.5KV. |
| 258 | NS Supply of lighting fixtures of surface mounted 15W edgelit LED Round Downlighterluminaire.The LED source used shall be complying with LM80 standards & LED source efficacy >120 lm/w. Epoxy white powder coated die cast aluminium housing; Efficient PMMA front visor;. The system lumen output of the luminaireof a minimum of 90 lms/W system efficacy with color temprature of 5700 deg K (ANSI Bin) and CRI>80. Integral Driver with constant current constant voltage (CVCC), P.F >0.9, THD<20% and Surge Protection of atleast 2.5KV. |
| 259 | NS Supply of lighting fixtures of surface mounted 12W edgelit LED Round Downlighterluminaire.The LED source used shall be complying with LM80 standards & LED source efficacy >150 lm/w. Epoxy white powder coated die cast aluminium housing; Efficient PMMA front visor;Highly reflective guide plate; The system efficacy of the luminaire upto 80 lms/W with color temprature of 3000/4000/5700/6500 deg K (ANSI Bin) and CRI>80. Integral Driver with constant current constant voltage (CVCC), P.F >0.9, THD<20% and Surge Protection of atleast 2.5KV. |
| 260 | NSSupply of lighting fixtures of 10W LED IP65 Bulkhead luminaire.The LED source used shall becomplying with LM80 standards & LED source efficacy >150 lm/w. Epoxy white powder coated die cast aluminium housing; Opal polycarbonate diffuser; The system lumen output of the luminaireof a minimum of 900 lumens with color temprature of 5700 deg K (ANSI Bin) and CRI>80. Integral Driver with constant current constant voltage (CVCC), P.F >0.95, THD<10% and Surge Protection of atleast 2.5KV |
| 261 | NS Supply of lighting fixtures of 36W surface mounted square LED luminaire with epoxy coated CRCA white powder coated housing, special translucent high transmitivity non yellowing (PMMA) Diffuser. Color temperature of 5700 degree kelvin (ANSI Bin rated) and CRI>80. The LED source used shall be medium/high power complying with LM80 standards & LED source efficacy >150 lm/w. Non-integral 3 stage isolated Driver with constant current constant voltage (CVCC), P.F >0.95 and Surge Protection of atleast >3 KV. System lumen output of the luminaire of a minimum of 100 lms/W |
| 262 | NS Supply of lighting fixtures ofHi-efficiency LED Floodlight Luminaire, Body made of di-castaluminium and hi-precision optics with beam angles 60º / 90º, System power 100W, 230V, CRI>80, 327mm X 218mmX177, color temperature 3000K/4000K/5700K with IP65, THD<10%, PF>0.95 , operating voltage range: 110 - 305V, system lumen output: 14000lm, Surge protection: 5kV internal and 10kV external, Operating temperature: 0°C - 50°C, Epoxy Potted Driver for better Thermal and Electrical isolation of components, LED: Nichia/Cree/Bridgelux/Osram, IP65, IK08, driver efficiency>90%, LED burning hours:L70@50000hrs, |
| 263 | NS Supply of LED light Exit signage of double sided Green Acrylic Signage (Exit/Name of building part written and arrow marked on it) of suitable size with hanging arrangement with wall using super bright LED having power consumption of 3 watts minimum 2 hours battery back-up operating between 85-265 volts AC, making connections etc.complete as |
| 264 | NS Supply and erection of double door sheet steel enclosure vertical type distribution boardsuitable for MCCB as incomer and SP/TP MCB\"S as outgoings etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work.Vertical TPN DB Double Door 4 way ( 8 incoming 3phase*4 outgoing) |
| 265 | NS Vertical TPN DB Double Door 8 way ( 8incoming 3phase*8 outgoing) |
AI Tender Summary
Tender Timeline
Nov 12, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedNov 28, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedNov 28, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender