Tender For Construction Of Community Hall Building Of Nandanpur High School Within Daspur-I Panchayat Samity 2Nd Phase
Tender Value
7.37 Lakhs
Estimated cost
Bid Submission
17 Nov 2022
0 days left
EMD
14750
Bank guarantee accepted
Document Fee
1500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
daspur → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Community Hall Building Of Nandanpur High School Within Daspur-I Panchayat Samity 2Nd Phase
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. Septic Tank (100 User) |
| 2 | Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity). Do - by fine sand. |
| 3 | Supplying and laying Polythene Sheet (150gm / sq.m.) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches. |
| 4 | Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work) With earth obtained from excavation of foundation. |
| 5 | Ordinary Cement concrete (mix 1:2:4) with graded stone ballast (20 mm nominal size) excluding shuttering and reinforcement. In Ground floor, Pakur variety. |
| 6 | Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per IS: 456-2000. |
| 7 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. For works in foundation, basement and upto roof of ground floor / up to 4m. Tor steel / Mild steel. |
| 8 | Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor) |
| 9 | 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineering-in-charge. |
| 10 | With prop. |
| 11 | Brick work with 1st class bricks in cement mortar (1:4). In superstructure, ground floor. |
| 12 | 125 mm. thick brick work with 1st class bricks in cement mortar (4:1) in ground floor. |
| 13 | Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. Sal |
| 14 | Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (Cost of concrete will be paid separately) 40mm X 6mm, 250mm Length. |
| 15 | Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark. 75mm X 40mm X 1.12mm. |
| 16 | Iron socket bolt of approved quality fitted and fixed complete. 150mm long x 10mm dia bolt. |
| 17 | Iron hasp bolt of approved quality fitted and fixed complete (oxidised) with 16mm dia rod with centre bolt and round fitting. 250mm long. |
| 18 | Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed With continuous plate base (Hexagonal/ Round rod) 150 mm grip x 12 mm dia rod. |
| 19 | Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings. In ground floor. 25mm thick shutters with 12mm thick panel. Local wood. |
| 20 | Labour for Chipping of concrete surface before taking up Plastering work. |
| 21 | Artificial stone in floor, dado, staircase etc with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners including raking out joints or roughening of concrete surface and application of cement slurry before flooring works using cement @ 1.75 kg/sq.m all complete including all materials and labour. In ground floor. mm. thick topping (High polishing grinding on this item is not permitted with ordinary cement). Using grey cement, 35 mm thick. |
| 22 | Plaster (to wall, floor, ceiling) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding / staging where necessary (Ground floor). |
| 23 | With 1:4 cement mortar, 10mm thick plaster. |
| 24 | With 1:6 cement mortar, 15mm thick plaster. |
| 25 | With 1:6 cement mortar, 20mm thick plaster. |
| 26 | Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc. NOTE:Cement 0.152 cu.m per100 sq.m. |
| 27 | M.S. or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in first floor. Grill weighing above 10 Kg./sq.mtr and up to 16 kg./sq.mtr.. |
| 28 | Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturer\"s specification) including cleaning and smoothning of surface. Two Coats |
| 29 | Applying decorative cement based paint of approved quality after preparing the surface including scraping the same thoroughly (plastered or concrete surface) as per manufacturer\"s specification. In Ground floor, Two coats. |
| 30 | Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 31 | Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 32 | Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary. |
| 33 | On timber or plastered surface, with super gloss (hi-gloss), two coats with two coats (with any shade except white) |
| 34 | On steel or other metal surface, with super gloss (hi-gloss) Two coats. |
| 35 | Supplying, Fitting & Fixing Factory made prelaminated P.V.C. door frame of size 50 mmx47 mm with a wall thickness of 5 mm, made out of extruded 5 mm Prelaminated PVC sheet miter cut at two corners and joined with two nos of 1.5 mm long brackets of 15 mm x15 mm M.S. square tube. The two vertical door profiles are to be reinforced with 19 mmx 19 mm M.S. Square tube of 19 gauge, weather seal to be provided through out the frame. The door frame shall be fixed with the wall using 65/100 mm M.S. Screws through the frame by using P.V.C fasteners. A minimum of 4 Nos of screws to be provided for each vertical member and minimum 2 Nos for horizontal member etc. complete as per Manufacturer?s specification and direction of Engineer-in-Charge. Gate. |
| 36 | Supplying, Fitting & Fixing 30 mm thick both side prelaminated Factory made solid Panel PVC Door Shutter consisting of outer frame made out of M.S. tubes of 19 gauge thickness and size 19 mmx19 mm for styles, top and bottom rails, M.S. frame shall have cost of steel primers of approved make and manufacture, M.S. frame covered with 5 mm th. heat moulded PVC “C” channel of size 30 mm th, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on either sides forming styles; and 5 mm th. 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm tapered in 45 degree on the inner side to form top & bottom rail and 115 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided either side of the panel with 10 mm (5 mm x 2) th.,20 mm wide cross PVC sheet as gap insert for top rail and bottom rail sheet to be fitted in the M.S. frame welded/sealed to the styles &rails with 7 mm (5 mm+2 mm) th.x15 mm wide PVC sheet beading on inner side and joined together with solvent cement adhesive. An additional 5 mm th. PVC strip of 20 mm which isto be stuck on the interior side of the “C” hannel using PVC solvent adhesive etc. complete excluding all necessary hardwares as perdirection of Engineer-in- Charge. |
| 37 | Supplying, fitting and fixing Shallow Water Closet Indian pattern (I.P.W.C.) of approved make in white vitreous chinaware in position (Excluding cost of concrete for fixing) 450 mm long. |
| 38 | Supplying fitting & fixing Foot rest for water closet of size 275 mm X 125 mm with artificial stone. |
| 39 | Add GST @ 12% |
| 40 | Add Labour Welfare CESS @ 1% |
AI Tender Summary
Tender Timeline
Nov 04, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedNov 17, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedNov 21, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender