Tender For Repair And Renovation Of Multipurpose Hall And Sport Flooring At Netaji Stadium, Port Blair Sub Work- Repair And Maintenance Of Multipurpose Hall
Tender Value
24.67 Lakhs
Estimated cost
Bid Submission
16 Nov 2022
0 days left
EMD
49358
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
blair → Andaman And Nicobar Islands
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Repair And Renovation Of Multipurpose Hall And Sport Flooring At Netaji Stadium, Port Blair Sub Work- Repair And Maintenance Of Multipurpose Hall
BOQ
| Sl. No. | Item Description |
| 1 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 2 | 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 3 | Centering and shuttering including strutting, propping etc. and removal of form work for : |
| 4 | Foundations, footings, bases for columns |
| 5 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : |
| 6 | 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources) |
| 7 | Centering and shuttering including strutting, propping etc. and removal of form for |
| 8 | Shelves (Cast in situ) |
| 9 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. |
| 10 | Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 11 | Providing and laying Autoclaved Aerated Concrete (AAC)blocksmasonrywith 150mm to 300mm thick with Grade 1 AAC blocksof density 551 to 650 kg/cum conforming to IS: 2185 (Part 3) in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for separately). |
| 12 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. |
| 13 | Granite stone slab of all colour and texture except black, Cherry/ Ruby red(7.1.1) Area of slab over 0.50 sqm |
| 14 | Providing and fixing in wall lining medium density fibre board IS: 14587:1998 marked, Pre-laminated one side decorative lamination and other side balancing lamination, with necessary fixing arrangement and screws etc. complete. |
| 15 | 12 mm thick. |
| 16 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 17 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). |
| 18 | 1st class teak wood. |
| 19 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately). |
| 20 | Cat.-I (A) teak wood(11.1.1) 35 mm thick shutters |
| 21 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : |
| 22 | Cat.-I (A) teak wood |
| 23 | Providing and fixing bright finished brass handles with screws etc. complete: |
| 24 | 125 mm |
| 25 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. |
| 26 | Providing and fixing to existing door frames. |
| 27 | 30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of \"H\" section, a uPVC hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. \"U\" cleats.The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness . The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer\"s specification and direction of Engineer-in-charge. |
| 28 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 29 | 100 mm |
| 30 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 31 | 150x10 mm |
| 32 | Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : |
| 33 | 250x10 mm |
| 34 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : |
| 35 | 300x16 mm |
| 36 | Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 300x100x150 mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). |
| 37 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 38 | Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. |
| 39 | G.I. pipes |
| 40 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding grouting the joints with white cement and matching pigments etc., complete. |
| 41 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding grouting the joints with white cement and matching pigments etc., complete. |
| 42 | Size of Tile 600x600 mm |
| 43 | Deduct for not using 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) bedding in laying of floor tiles and jointing with grey cement slurry @ 3.3 kg/ sqm. |
| 44 | Fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3mm thickness. |
| 45 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. |
| 46 | Size of Tile 600x600 mm |
| 47 | Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately). |
| 48 | 6 mm thick Cement fiber board as per IS: 14862 |
| 49 | 12 mm cement plaster of mix : |
| 50 | 1:4 (1 cement: 4 fine sand) |
| 51 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer\"s specification. |
| 52 | Two or more coats on new work |
| 53 | Finishing walls with Acrylic Smooth exterior paint of required shade : |
| 54 | New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 55 | Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : |
| 56 | Two or more coats on new work |
| 57 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : |
| 58 | Water thinnable cement primer |
| 59 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : |
| 60 | Two or more coats on new work |
| 61 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 62 | 12 mm cement plaster finished with a floating coat of neat cement of mix : |
| 63 | 1:4 (1 cement: 4 fine sand) |
| 64 | Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below:1. The surface to be polished is rubbed with sand paper 80/ 120 no. and then with sand paper of 160/180 nos.2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs.3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs.4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.) |
| 65 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: |
| 66 | One or more coats on old work |
| 67 | Finishing walls with Acrylic Smooth exterior paint of required shade : |
| 68 | Old work (One or more coat applied @ 0.90 ltr/10 sqm). |
| 69 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. |
| 70 | With cement mortar 1:4 (1 cement : 4 fine sand) |
| 71 | DismantlingW.C.Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in-Charge. |
| 72 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : |
| 73 | Of area 3 sq. metres and below |
| 74 | Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead : |
| 75 | Thickness above 10 mm up to 25 mm |
| 76 | Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead : |
| 77 | Of sectional area 40 square centimetres and above |
| 78 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. |
| 79 | For thickness of tiles 10 mm to 25 mm |
| 80 | Providing and fixing soil, waste and vent pipes : |
| 81 | 100 mm dia(46.1.1) Sand cast iron S&S pipe as per IS: 1729 |
| 82 | 75 mm diameter :(46.2.1) Sand cast iron S&S pipe as per IS: 1729 |
| 83 | Providing and fixing bend of required degree with access door, insertionrubber washer 3 mm thick, bolts and nuts complete. |
| 84 | 100 mm dia(47.1.1) Sand cast iron S&S as per IS - 1729 |
| 85 | 75 mm dia(47.1.1) Sand cast iron S&S as per IS - 1729 |
| 86 | Providing and fixing P.V.C. waste pipe for sink or wash basin includingP.V.C. waste fittings complete. |
| 87 | Flexible pipe32 mm dia |
| 88 | Providing and fixing mirror of superior glass (of approved quality) andof required shape and size with plastic moulded frame of approvedmake and shade with 6 mm thick hard board backing : |
| 89 | Rectangular shape 453x357 mm |
| 90 | Providing and fixing PTMT grating of approved quality and colour. |
| 91 | Rectangular type with openable circular lid(50.1.1) 150 mm nominal size square 100 mm diameter of the inner hinged round grating |
| 92 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls |
| 93 | 20 mm nominal dia Pipes |
| 94 | 25 mm nominal dia Pipes |
| 95 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work): |
| 96 | 40 mm nominal bore |
| 97 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work |
| 98 | 40 mm dia nominal bore |
| 99 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : |
| 100 | 25 to 40 mm nominal bore |
| 101 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : |
| 102 | 25 mm nominal bore |
| 103 | 40 mm nominal bore |
| 104 | Providing and fixing uplasticised PVC connection pipe with brass unions : |
| 105 | 30 cm length(56.1.1) 15 mm nominal bore |
| 106 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 107 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): |
| 108 | With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) |
| 109 | Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in- charge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately). |
| 110 | Providing and fixing anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868. Minimum anodic coating of grade AC 15) sub frame work for windows and ventilators with extruded built up standard tubular sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia and size (Dash fastener to be paid for separately). |
| 111 | Providing and fixing auto closing system with built-in control cock with wall flange (Make of Jaquar PRS-073 or equivalent) as per the direction of Engineer - in - charge. |
| 112 | Providing and fixing Urinal with fixing accessories, size 375X320X620 mm (Make of Jaquar USR-WHT-13253O or equivalent) as per the direction of Engineer - in - charge. |
| 113 | Providing and fixing exposed part kit of concealed stop cock with fitting sleeve, operating lever & Adjustable wall flange with seal(Make of Jaquar COP-083KPM or equivalent) (compatible with ALD-083 & ALD-089) as per the direction of Engineer - in - charge. |
| 114 | Providing and fixing two way bib cock with wall flange: (make ORP-10041PM) Jaquar or equivalent |
| 115 | Providing and fixing Angular Stop Cock with Wall Flange of approved quality of make Jaquar COP-057PM or equivalent. |
| 116 | Providing and fixing Bib Cock with wall flange (Make of Jaquar KUP-35037PM or equivalent) as per the direction of Engineer - in - charge. |
| 117 | Providing and fixing towel ring make of Jaquar ACN-1121BN or equivalent. |
| 118 | Providing and fixing Towel Rack 600 mm long without lower hanger but with 3 hooks, Stainless Steel (Make of Jaquar ACN-1181FHS or equivalent) as per the direction of Engineer - in - charge. |
| 119 | Providing and fixing toilet paper holder (Toilet roll holder) with flap: Cat No. ACN-1151N of make Jaquar or equivalent as directed by the Engineer - in - charge. |
| 120 | Providing and fixing Overhead Shower ø105mm Round Shape Single Flow with Air Effect (ABS Body & Face Plate Chrome Plated) with Rubit Cleaning System (Make of Jaquar OHS-1709 or equivalent) as per the direction of Engineer - in - charge. |
| 121 | Providing and fixing Under Counter Basin with Fixing Accessories, Size 605X410X200 mm, Shape Rectangular (Make of Jaquar FNS-WHT-40701 or equivalent) as per the direction of Engineer - in - charge. |
| 122 | Providing and fixing (Floor mounted coupled WC) Bowl for Coupled WC with UF soft close slim seat cover, Hinges, Fixing Accessories and Accessories Set, Size: 365x630x750 mm, (Make of Jaquar FNS-WHT-40751P180UFSM or equivalent) P Trap-180mm, Cistern with cistern fittings for 40751S220UFSM (Make of Jaquar FNS-WHT-40201 or equivalent) as per the direction of Engineer - in - charge. |
| 123 | Providing and fixing Pillar Cock (Make of Jaquar DRC-37001 or equivalent) as per the direction of Engineer - in - charge. |
| 124 | Providing and fixing Click Clack Waste 32mm Size Full Thread With 80mm Height (Make of Jaquar ALD-727 or equivalent) as per the direction of Engineer - in - charge. |
| 125 | Providing and fixing Hand Shower (Health Faucet) with 8mm Dia, 1.2 Meter Long Flexible Tube & Wall Hook (Make of Jaquar ALD-573 or equivalent) as per the direction of Engineer - in - charge. |
AI Tender Summary
Tender Timeline
Nov 03, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedNov 16, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedNov 16, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender