|
| 1 | Civil works |
| 2 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5m as directed by Engineer-in-Charge.All kinds of soil |
| 3 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil |
| 4 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil |
| 5 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 6 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 7 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 moutside the periphery of the area cleared. |
| 8 | Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunks and branches, removing the roots and stacking of serviceable materials and disposal of unserviceable mayerials.Above 240 cm girth |
| 9 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 Cement: 2 course sand (zone-III) : 4 graded stone aggregate 20 mm nominal size). |
| 10 | 1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size). |
| 11 | Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20mm nominal size). |
| 12 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 13 | Centering and shuttering including strutting, propping etc. and removal of form for all heights :Foundations, footings, bases of columns, etc. for mass concrete |
| 14 | Walls (any thickness) including attached pilaster, butteresses, plinth and string courses etc |
| 15 | Suspended floors, roofs, landings, balconies and access platform. with water proof ply 12 mm thick |
| 16 | Shelves (Cast in situ) |
| 17 | Lintels, beams, plinth beams, girders, bressumers and cantilevers. with water proof ply 12 mm thick |
| 18 | Columns, Pillars, Piers, Abutments, Post and struts |
| 19 | Edges of slabs and breaks in floors and wallsUnder 20 cm wide |
| 20 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 21 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 22 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately).All works upto plinth level |
| 23 | All works above plinth level upto floor V level |
| 24 | Add for using extra cement in the items of design mix over and above the specified cement content therein. |
| 25 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 26 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 27 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in Cement mortar 1:4 (1 cement :4 coarse sand) |
| 28 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand) |
| 29 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Raj Nagar Plain white marble/Udaipur green marble/Zebra black marbleArea of slab over 0.50 sqm |
| 30 | Granite of any colour and shadeArea of slab upto 0.50 sqm |
| 31 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.Marble work |
| 32 | Granite work |
| 33 | Providing and fixing 1st quality Ceramic glazed wall tilesconforming to NIS : 15622 (thickness to be specified by the manufacturer of approved make in all colours, shades, except burgundy bottle green, black of any sizes as approved by Engineer-in-Chrge, in skirting, riser of steps and dados, over 12mm thick bed of cement mortar 1:3 andjointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 34 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 35 | 25 mm thick (for cupboard) including ISI marked nickle plated bright finished M.S piano hinges with necessary screws |
| 36 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to steel windows by welding |
| 37 | Providing M.S Piano hinges ISI marked IS:3818 finished with nickle plating and fixing with necessary screws etc complete.Overall width 35 mm |
| 38 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :250 x 10 mm |
| 39 | 200 x 10 mm |
| 40 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :125 mm |
| 41 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.Single rubber stopper |
| 42 | Providing and fixing PVC rigid foam sheet 1 mm thick on existing door shutters (bathroom and W.C. doors) using synthetic rubber based adhesive. |
| 43 | Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer. |
| 44 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 45 | Steel work in built up tubular (round, square or rectangular hollow tubes etc) trusses etc including cutting, hoisting, fixing in position and applying priming coat of approved steel primer including welding and bolted with special shaped washers etc completeHot finished welded type tubes |
| 46 | Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. |
| 47 | Steel work welded in built up sections/framed work including cutting, hoisting, fixing in position and applying priming coat of approved steel primer using structural steel etc as requiredIn stringers, treads, landing etc of stair cases including use of chequered plate wherever required all complete |
| 48 | Providing and fixing hand rail of approved size by welding etc to steel ladder railing, balcony railing, stair case railing and similar work including applying priming coat of approved steel primerM.S. tubes |
| 49 | Extra for making chequers of approved pattern on cement concrete floors, steps, landing, pavement etc |
| 50 | Courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc complete on 20 mm thick bed of cement mortar 1: 4 |
| 51 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thick. |
| 52 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 53 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600x600 mm |
| 54 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 55 | Providing and fixing M.S. holder-bat clamps of approved design to C.I or S.C.I rain water pipes embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : For 100 mm diameter |
| 56 | For 150 mm diameter |
| 57 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter |
| 58 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Coupler75 mm |
| 59 | 100 mm diameter |
| 60 | Single tee with door75x75x75 mm |
| 61 | 110x110x110 mm |
| 62 | Single tee without door75x75x75 mm |
| 63 | 110x110x110 mm |
| 64 | Bend 87.5°75 mm bend |
| 65 | 100 mm bend |
| 66 | Shoe (Plain)75 mm bend |
| 67 | 100 mm bend |
| 68 | Providing and fixing precoated galvanised iron profile sheet (size, shape and pitch of corrugation as approved by engineer-in-charge) 0.50 mm (+0.05%) total coated thickness with zinc coating 120 grams per sqm as per IS:277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 micronss. Sheet should have protective guards film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as directed by engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size 5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/vertical or curved surface excluding the cost of purlins, rafter and trusses and including |
| 69 | Providing and fixing precoated galvanised Steel sheet roofing accessories0.50 mm (+0.05%) total coated thickness with zinc coating 120 grams per sqm as per IS:277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 micronss using self drilling /self tapping screws complete Ridges plain (500-600 mm) |
| 70 | Providing & fixing false ceiling at all height including providing & fixing of framework made of special section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10 x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I chanels 45 x15 x 0.90mm running at the spacing of 1200 mm c/c, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each havinglips of 10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of Calcium Silicate Board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing & finishing to a flush finish of tapered and square edges of the board with recommended jointing compounds, jointing tapes,finishing with jointing compounds in three layers covering up to 150mm on both sides of joints and two coats of primer suitable for boards, all as per manufacture\"s specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all completeas per drawings, specificaton and direction of the Engineer in chargebut excluding the cost of painting with: Code8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process. |
| 71 | 12 mm cement plaster of mix :1:4 (1 cement: 4 fine sand) |
| 72 | 15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix :1:4 (1 cement: 4 fine sand) |
| 73 | 15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix :1:3 (1 cement: 3 fine sand) |
| 74 | 6 mm cement plaster of mix :1:3 (1 cement: 3 fine sand) |
| 75 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete |
| 76 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :New work (two or more coats) over and including waterthinnable priming coat with cement primer |
| 77 | Finishing walls with water proofing cement paint of required shade :New work (Two or more coats applied @ 3.84 kg/10 sqm) |
| 78 | Painting (two or more coats) on rain water, soil waste and vent pipes and fittings with synthetic enamel paint of approved brand and manufacture and required colour over a priming coat of approved steel primer on new work.100 mm diameter pipes |
| 79 | 150 mm diameter pipes |
| 80 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work |
| 81 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) |
| 82 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge .(Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight notless than 10 kg/ sqm) |
| 83 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size580x440 mm with integral type foot rests |
| 84 | Providing and fixing white vitreous china pedestal type water closet(European type W.C. pan) with seat and lid, 10 litre low level whiteP.V.C. flushing cistern, including flush pipe, with manually controlleddevice (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls andfloors wherever required :W.C. pan with ISI marked white solid plastic seat and lid |
| 85 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :One urinal basin with 5 litre white P.V.C. automatic flushing cistern |
| 86 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brasspillar taps, 32 mm C.P. brass waste of standard pattern, includingpainting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630x450 mm witha pair of 15 mm C.P. brass pillar taps |
| 87 | White Vitreous China Flat back wash basin size 450x300 mm with single 15mm C.P. brass pillar tap |
| 88 | Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink with drain board510x1040 mm bowl depth 250 mm |
| 89 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Semi rigid pipe32 mm dia |
| 90 | 40 mm dia |
| 91 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 92 | Providing and fixing 600x120x5 mm glass shelf with edges round off supported on anodised aluminium angle frame with C.P brass brackets and guard rail complete fixed with 40 long screws, rawl plugs etc., complete. |
| 93 | Providing and fixing toilet paper holderC.P. brass |
| 94 | Providing and fixing soil, waste and vent pipes :100 mm diaCentrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 |
| 95 | Providing and fixing soil, waste and vent pipes :75 mm diameterCentrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 |
| 96 | Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.100 mm diaHubless centrifugally cast (spun) iron epoxy |
| 97 | Providing and fixing plain bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.100 mm diaSand cast iron S&S as per IS: 3989 |
| 98 | Providing and fixing plain bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.75 mm diaSand cast iron S&S as per IS: 3989 |
| 99 | Providing and fixing single equal plain junction of required degreewith access door, insertion rubber washer 3 mm thick, bolts andnuts complete.100x100x100 mm Sand cast iron S&S as per IS: 3989 |
| 100 | Providing and fixing single equal plain junction of required degreewith access door, insertion rubber washer 3 mm thick, bolts andnuts complete.100x100x100 mm Sand cast iron S&S as per IS: 3989 |
| 101 | Providing and fixing collar :100mmSand cast iron S&S as per IS - 3989 |
| 102 | Providing lead caulked joints to sand cast iron/centrifugally cast(spun) iron pipes and fittings of diameter :100 mm |
| 103 | 75 mm |
| 104 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. |
| 105 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.600 mm long towel rail with total length of 645 mm, width78 mm and effective height of 88 mm, weighing not lessthan 190 gms. |
| 106 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc15 mm nominal outer dia Pipes |
| 107 | 20 mm nominal outer dia Pipes |
| 108 | 25 mm nominal outer dia Pipes |
| 109 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.32 mm nominal outer dia Pipes |
| 110 | 40 mm nominal outer dia Pipes |
| 111 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc40 mm dia nominal bore |
| 112 | Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks ofclass designation 7.5 |
| 113 | Providing and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329 :100 mm dia Ductile Iron Class K-7 pipes |
| 114 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.With common burnt clay F.P.S. (non modular) bricks ofclass designation 7.5 |
| 115 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete300 mm dia. R.C.C. pipe |
| 116 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and |
| 117 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :15 mm nominal bore |
| 118 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore |
| 119 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.15 mm nominal bore. |
| 120 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:893115 mm nominal bore. |
| 121 | Providing and fixing PTMT grating of approved quality and colour.Circular type100 mm nominal dia |
| 122 | Electricals |
| 123 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C |
| 124 | Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulatedcopperconductorsinglecorecableinsurface/ recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 125 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 126 | 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 127 | 2 X 4 sq. mm + 1 X 4 sq. mm earth wire |
| 128 | 2 X 6 sq. mm + 2 X 4 sq. mm earth wire |
| 129 | 4 X 10 sq. mm + 2 X 6 sq. mm earth wire |
| 130 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. |
| 131 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. |
| 132 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)6 way (4 + 18), Double door |
| 133 | 8 way (4 + 24), Double door |
| 134 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole |
| 135 | Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required40A |
| 136 | 63A |
| 137 | Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required40A |
| 138 | 63A |
| 139 | Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required. |
| 140 | Supplying and laying 25 mm X 5 mm copper strip at 0.50 meter below ground as strip earth electrode, including connection/terminating with nut, bolt, spring, washer etc. as required.(Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50 mm) |
| 141 | Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required. |
| 142 | Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc.complete as required. |
| 143 | Providing and fixing of lightning conductor finial, (single prong) with base plate including holes etc.complete as required. |
| 144 | Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 Nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required. |
| 145 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.Upto 35 sq. mmAbove 95 sq. mm and upto 185 sq. Mm |
| 146 | Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required. |
| 147 | Fabrication, supplying, installation, testing and commissioning of indoor type panel, IP-42 cubical type panel suitable for 415 volt, 3 phase, 4 wire, 50 Hz AC supply, compartmentalized of depth not less than 300 mm made of 2 mm thickCRCA sheet steel, cleaning, processing, & finishing complete with 7/8 tank process for powder coating in approved shade of welded construction with necessary stiffner,suitable compartments for mounting of switch gear and and other acessories with hinged type door at front side with locking arrangement, with 200 amps capacity4 strips aluminium bus bar of high conductivity with DMC/SMC bus bar support, connection and inter connection of switch gears, proper gasketing adequate ventilation arrangement, entire panel shall have a common aluminium earth bar of size 30mm x 5mm at the rear,control wiring with 2.5 sq.mm. FRLS PVC insulated copper conductor S/C cable, cable alleys, individual cable gland plate (3mm thick), terminal block for incoming and each outgoing,and fixed on 35mmX35mmX5mm angle iron frame work leg including supplying and fixing of the following switchgear, accessories as reqd. (General arrangement and schematic diagram to be approved by the department before start of fabrication.)(Note : MCCB lcs=100% Icu) (For Building No-2)a) 100 Amp FP MCCB (36KA)(Incoming) ( Legrand/ L&T/ CG/Havells) - 1 No.b) 63Amp FP MCCB (16KA)(outgoing) ( Legrand/ L&T/ CG/Havells) - 7 Nosc) 40 Amp FP MCCB (16KA)(outgoing) ( Legrand/ L&T/ CG/Havells) -4 Nos.d) 0 - 200 Amps CT operated digitalAmmeter (96mmX96mm) with in-built selector switch (L& T/AE- make) alongwith cast resin 200/5A CT of 15 VA burden accuracy class-1 with 3 Nos 2A (10KA) SP MCB - 1Sete) 0 - 500 Volts (96mmX96mm)digital Voltmeter with in-built selector switch with 3 Nos. 2A (10 KA) SP MCB - 1 set(L & T /Kaycee)f) Phase Indication LED lamp for each phaseswith 3 Nos. 2A (10KA) SP MCB - 1 setIncoming a) 100 Amp FP MCCB having breaking capacity (36KA) thermal magnetic release (Ics=100% Icu)( Make : Legrand/ L&T/ CG/Havells) - 1 No.Outgoinga) 63Amp FP MCB 10 KA \"C \" curve( Make :Legrand/ L&T/ CG/Havells) -7 Nos.b) 40 Amp DP MCCB having breaking capacity(16KA) thermal magnetic release(Ics=Icu) (Make : L&T) -4 Nos. |
| 148 | Supplying and fixing of 1 No 4 W LED lampin the existing brass batten/angle holder including connection etc. as reqd. (Make- Havells Model no. LHLDDEECYC8U004/Bajaj/ Phillips) |
| 149 | Supplying and fixing brass batten/ angle holder withincluding connection etc. as required.(For Quarter & warden) |
| 150 | Supplying, Installation, testing and commissioning of 1 x 18 watt box type LED Tube Light Fitting with one No. 18 W LED Tube, complete with all accessories and tube etc. Directly on ceiling / wall, i/c connections with 1.5 sq. Mm. FRLS PVC insulated, copper conductor, single core cable and earthing etc. as reqd. (Make : Bajaj /Havells/Phillips / Wipro) |
| 151 | Supplying ,installation & testing of6/10 Wattround/square surface down light mounted LED luminaire with white powder coated polycarbonate housing and pressure die-cast heat sink, fixing dirrectlyon ceiling i/c connection etc.as required.(Make Havells/ Bajaj / philips) |
| 152 | Supplying ,installation & testing of24 Watt600X600mm surface down light mounted LED luminaire with white powder coated polycarbonate housing and pressure die-cast heat sink, fixing dirrectlyon ceiling i/c connection etc.as required.(Make Havells/ Bajaj / philips) |
| 153 | Supply, installation, testing & commissioning of Ceiling fan, 1200 mm sweep, Energy 5 Star complete with capacitor, canopy and down rod including electronic step regulator modular type 5 step 2 module with provision from ceiling rose/connector to fan and regulator all as specified as required. (Make Havells/ Bajaj / philips ) |
| 154 | Supply, installation, testing & commissioning of Exhaust fan 300 mm dia; 900 rpm complete with louvers and provision of cable from ceiling rose/connector to fan all as specified as per HAVELLS Turbo Force or equivalent. |
| 155 | Supplying of following size ISI marked XLPE insulated and PVC sheathed aluminium conductor armoured U.G. cable of 1.1 KV grade conforming to IS 7098(Part 1) 1988 andammended up to date as reqd. (Make : Polycab/Havell\"s) c) 3.5 Core 185 Sqm |
