Tender For Special Repair To Roofing Of Godowns With Iron Profile Sheet At Fsd Kurali Under District Chandigarh
Tender Value
Ref. Documents
Estimated cost
Bid Submission
05 Nov 2022
0 days left
EMD
56692
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
kurali → Chandigarh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Special Repair To Roofing Of Godowns With Iron Profile Sheet At Fsd Kurali Under District Chandigarh
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling roofing including ridges, hips, valleys and gutters etc.and stacking the material within 50 metres lead of :: Asbestos sheet. |
| 2 | Taking out wind ties from roof including cutting out rusted bolts, nuts etc. and removing materials to any distance within compound and stacking. |
| 3 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge)0.50 mm + 0.05 %, total coated thickness with zinc coating 120 gsm as per IS: 277 in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses. |
| 4 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + 0.05 % total coated thickness, Zinc coating120gsm as per IS: 277 in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : ridgessame profile sheet (500-600mm), |
| 5 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase |
| 6 | Fixing of old wind tie with new fittings including painting two or more coats with anticorrosive bitumastic paint of approved brand & manufacture over andincluding priming coat of ready mixed zinc chromate yellow primer of approved brand. |
| 7 | Half brick masonary with common burnt clay F.P.S. (non modular) bricks of clas designation 7.5 in superstructure above plinth level up to floor V level Cement mortar 1:4 (1 cement: 4 coarse sand) |
| 8 | Supply , installation, testing & commissioning of turbo ventilators size 22” in stainless steel 430 grade with approximate weight 4.85kg .The ventilator should have air absorption of 7 kg per hour 2440 CFMwith blade length 369mm wings of 80mm,outer wings := 22”24nos inner wings 22”-6Nos, with self lubricating ball bearing etc.complete as per manufacture\"s specification and as per direction of Engineer-in-charge |
| 9 | Deduct old ACC sheets received from dismantling roof (Market Rate) |
| 10 | Deduct J hooks available from dismantling of roof of godown and veranda. (Market rate) |
| 11 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. |
| 12 | Provinding and fixing expanded metal with daigonal of rhombus 20x60 (with weight not less than 3.50 Kg per sqm), welded by gas welding to mild steel flats 18mmx3mm & fixed with screws to M.S.angle 30x30x4mm (weight not less than 1.75kg per meter) with 15x3mm lugs, 10cm long embedded in cement conrete blocks 15x10x10cm of 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screw or with fixing clips or with bolts and nuts as required as per drawing including applying including applying a priming coat of steel zinc chomate primer. |
AI Tender Summary
Tender Timeline
Oct 27, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedNov 05, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedNov 07, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender