Tender For Construction Of Phc Building At Jangeshu (Masoolkhana)Distt Solan
Tender Value
2.11 Crore
Estimated cost
Bid Submission
28 Oct 2022
0 days left
EMD
4.23 Lakhs
Bank guarantee accepted
Document Fee
5000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
kasauli → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Phc Building At Jangeshu ( Masoolkhana ) Distt Solan Sh C O Building Portion Rain Water Harvesting Tank Septic Tank And Site Development Work Etc
BOQ
| Sl. No. | Item Description |
| 1 | Cutting and disposal of earth work by mechanical in all heights and depths in all kinds of soils, including saturated soils comprising of pick work, jumper work and blasting work both in soft and hard rock with chiseling and wedging out of rock (where blasting is prohibited) and their intermediate classification of soils including, dewatering wherever required, setting of to therequired lines, levels as shown on the drawing and directed by the Engineer -in-charge at site., according to the HP.PWD. specification of 1990 (one thousand nine hundred ninety) volume-I (one) and sorting out useful and unuseful material and transportation of the unuseful material for disposing atdumping siteas per satisfaction of Engineer- in -charge through all modes of transportation including head load ,animal load or mechanical means along with its leveling fine dressing and with all kinds of labour, machineries, tools equipments and safety measures and incidentals necessary to complete the work by mechanical means and labour ( if required ).All the surplus excavated earth to be dumped at dumping site(dumping sites will be arranged by the contractor on his own cost). Any loss to the public and private propriety, human being, machinery during the course of execution and disposal of serviceable and unserviceable materials shall be the absolute responsibility of the contractor and shall have to be duly compensated by him in all respects including all incidental charges. |
| 2 | Earth work in excavation for structure in all depths as per drawing and technical specification for rural roads August 2004 clause 305.1 including setting out,construction of shoring abd bracing, removal of stumps and other deleterious materials and disposal in all leads and lift including dressing of sides and bottom and back filling in trenches with excavated suitable materials. All work of rockcutting by blasting shall be carried out by taking all necessary precautions against soil erosion damage to hill side water pollution etc. and to protect stability of hill side rock shall be excavated with chiseling and wedging out rock (where balsting is prohibited) all earth work in cutting/ excavation including rock excavation shall be carried out true to lines grades, side slopes, width , camber super elevation and level as shown on the drawings or as directed by the Engineer-in-charge hauling and stacking of materials useful for construction at suitable sites and safe disposal of unsuitable cut materials in specified dimension or as directed by the Engineer-in-Charge. If the foundation of the structure is in an area with stagnant water or water is met with in the excavation due to spring seepage rain and other causes it shall be remove by suitable diversion bailing out or pumping as directed and the area of the foundation or embankment shall be kept dry. All the surplus excavated earth to be dumped at dumping site(dumping sites will be arranged by the contractor on his own cost).Any loss to the public or private property during the course of excavation shall be the sole responsibility of the contractor which shall have to be dully compensated by him at his on cost in all cases. including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. |
| 3 | Supply and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete including carriage of materials in all leads and lifts as per thedirections of the Engineer-in-Charge. |
| 4 | Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concretecomplete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 5 | Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 6 | Centering and shuttering including strutting, propping etc. and removal of form for : Columns, Pillars, Piers, Abutments, Posts and Struts Circular complete ncluding carriage of material in all leads and lifts as per direction of the Engineer - in - Charge. |
| 7 | Centering and shuttering including strutting, propping etc. and removal of form for : Stairs, (excluding landings) except spiral stair cases complete including carriage of material in all leads and lifts as per direction of the Engineer - in - Charge. |
| 8 | Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers complete including carriage of material in all leads and lifts as per direction of the Engineer - in - Charge. |
| 9 | Centering and shuttering including strutting, propping etc. and removal of form for : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. including getting out the excavated soil and disposal of surplus excavated soils as directed, complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 10 | Centering and shuttering including strutting, propping etc. and removal of form for : Edges of slabs and breaks in floors and walls Under 20 cm wide complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 11 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering: All work up to plinth level including carriage of materials in all leads and lifts as per thedirections of the Engineer-in-Charge.(i)1:5:10 (One cement : five coarse sand): ten graded stone aggregate 40 mm (forty milimetre) nominal Size |
| 12 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level including carriage of materials in all leads and lifts as per thedirections of the Engineer-in-Charge.(i)1:4:8 (One cement : four coarse sand): eight graded stone aggregate 40 mm (forty milimetre) nominal Size) |
| 13 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to all level :In retaining wall etc.1:3:6 (1 Cement : 3 coarse sand): 6 graded stone aggregate 40 mm nominal size) complete including carriage of material in all leads and lifts as per direction of the Engineer - in - Charge. |
| 14 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level: i)1:1.5:3 (1 cement : 1.5 coarse sand): 3 graded stone aggregate 20 mm nominal size) complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 15 | Reinforced cement concrete work in beams, suspended floors, roofslandings, balconies, shelves, chajjas, lintels, bands, plain window sills,above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm nominal size) complete including carriage of material in all leads and lifts as per direction of the Engineer - in - Charge. |
| 16 | Reinforced cement concrete work in columns, pillars,posts and struts etc. complete, including carriage of material in all leads and lifts as per direction of the Engineer - in - Charge. |
| 17 | Reinforced cement concrete work in Stair cases ( except spiral stair case ) excluding landings but including preparing of the surface & finishing of nosing upto all floor level complete including carriage of material in all leads and lifts as per direction of the Engineer - in - Charge. |
| 18 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm nominal size) |
| 19 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto all level.Tor steel and Medium Tensile steel bars complete including carriage of material in all leads and lifts as per direction of the Engineer - in - Charge. |
| 20 | Extra for rendering smooth the top of suspended floors, landings and staircases (treads and risers) with cement mortar 1:2 (1 cement : 2 coarse sand), including a floating coat of neat cement and protecting the surface with a layer of 7.5 cm of earth laid over 15 mm of fine sand in case of suspended floor and bricks laid in mud mortar in case of landings and steps, including subsequent removal and cleaning of the same complete including carriage of material in all leads and lifts as per direction of the Engineer - in - Charge. |
| 21 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : Cement mortar 1:4 (1 cement : 4 coarse sand) complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 22 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure in : Cement mortar 1:4 (1 cement : 4 coarse sand) complete including carriage of material in all leads and lifts as per direction of the Engineer - in - Charge. |
| 23 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in Cement mortar 1:6 (1 cement : 6coarse sand) (1 cement : 6coarse sand) complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 24 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6coarse sand) complete including carriage of material in all leads and lifts as per direction of the Engineer - in - Charge. |
| 25 | Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand) complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 26 | Boulderfilling tightly hand packed under floor including watering, ramming, consolidating etc. complete including carriage of material in all leads and lifts as per direction of the Engineer - in - Charge. |
| 27 | Stone filling behind retaining walls complete including carriage of material in all leads and lifts as per direction of the Engineer- in -Charge. |
| 28 | Supplying and filling brocken/crushed stone aggregate chipping of hard stone of 40 mm size including carriage of material in all leads and lifts as per direction of the Engineer - in - Charge. |
| 29 | Providing weep holes in brick masonry/stone masonry/plain concrete/reinfoced concrete, abutment, wing walls with 100 mm dia PVC pipe extending through the full length with of the structure with the slope of I (V) : 20 (H) towards drawing face complete as per drawing and technical specifications complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 30 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. complete including carriage of material in all leads and lifts:- 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws complete including carriage of material in all leads and lifts as per direction of the Engineer - in - Charge. |
| 31 | Providing and fixing shutter of main enterance door in 2nd. Class deodar wood having top rail 10x4 cm middle rail 15x4cm bottom rail 20x4cm sash bar 4x4 cm and panel below locking rail 12mm thick phenol bonded (both side) prelaminated BWP grade particle board in matt finish ISI marked IS No. 12823 as per approved shade of Kavista or its equivalent and 5.5mm thick glass panel above lock rail, 40mm thick as per Architect drawing including carriage of material in all leads and lifts as per direction of the Engineer - in - Charge. |
| 32 | Providing and fixing 18 mm thick, 150 mm wide pelmet of coir veneer board ISI marked IS : 14842, including top cover of 6 mm coir veneer board, nickle plated M.S. Pipe 20 mm dia. (heavy type) curtain rod with nickel plated brackets, including fixing with 25x3 mm M.S. Flat 10 cm long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm on both inner side of pelmet and rawl plugs 75 mm long etc. all complete.including carriage of material in all leads and lifts as per direction of the Engineer - in - Charge. |
| 33 | Providing and fixing M.S. grills of requirepattern in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws.including carriage of material in all leads and lifts as per direction of the Engineer - in - Charge. |
| 34 | Providing and fixing 19 mm thick commercial board water proof shutter for cup boards including fixing with nickel plated piano hinges with screws etc. complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 35 | Providing and fixing 19 mm thick commercial board water proof in shelves, lining, box for cup boards with butt joints fixed with nails and screws etc complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 36 | Providing and fixing 6mm thick ply wood lining with butt jointing and nails (frame work and cover fillets to be measured and paid for separately complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 37 | Providing and fixing 0.80 mm thick coloured or plain laminated sheet (sunmica) on boards / ply wood sheets with approved adhesive and nails complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 38 | Providing and fixing square edged cover fillets (beading)19 x 6 mm section including mitring at junction with wooden screws / nails etc complete of hard wood including carriage of material in all leads and lifts. |
| 39 | Providing and fixing PGI Sheet 0.63mm thick lining with butt jointing and nails with necessary scwews complete as per Architectural drawing.including carriage of material in all leads and lifts. |
| 40 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. : 250mm x 10mm. |
| 41 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge :200 X 10 mm |
| 42 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. :125mm. |
| 43 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge:75 mm. |
| 44 | Providing and fixingaluminium sliding door bolts (Barrel type) anodized transparent or dyed to required shade and colour with bolts and nuts etc. complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge.:-300 X 16 mm |
| 45 | Providing and fixingaluminium sliding door bolts (Barrel type) anodized transparent or dyed to required shade and colour with bolts and nuts etc. complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge.:250 X 16 mm. |
| 46 | Providing and fixing oxidised M.S. double acting spring hinges with necessary screws etc. complete. ccomplete including carriage of material in all leads and lifts as per direction of the Engineer in Charge:-.150 mm |
| 47 | Providing & fixing 115 mm M.S bright finished brass hasps and stapples (safety type)with necessary screws complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 48 | Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 49 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 50 | Precast terrazo tiles 22 mm thick with graded marble chips of size upto 12 mm, laid in floors, and landings, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement:4 coarse sand) :Light shade pigment using portland cement complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 51 | Providing and fixing Precast terrazo tiles 22 mm thick with graded marble chips of sizes upto 12 mm, in skirting and risers of steps not exceeding 30 cm in height, on 12mm thick cement plaster 1:3 (1 cement : 3 coarse sand), jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing completeincluding carriage of material within all leads and lifts as per direction of Engineer-in-charge:- Medium shades pigment using ordinary cement |
| 52 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete Size of Tile 600mm X 600mm. including carriage of material within all leads and lifts as per direction of Engineer-in-charge |
| 53 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. completeSize of Tile 600mm x 600mm. including carriage of material within all leads and lifts as per direction of Engineer-in-charge |
| 54 | Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in- Charge In flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand)Acid and alkali resistant tile. |
| 55 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed ofsand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge:- 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern. |
| 56 | Providing edge moulding to 18 mm thick marble/Kotahstone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. |
| 57 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble |
| 58 | Tile work in skirting, risers of steps and dado up to 2 m height over 12 mm thick bed of cement mortar 1:3 (1 cement :3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm, including pointing in white cement mixed with pigment of matching shade complete. Glazed tiles 10 mm thick. |
| 59 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete 40 mm thick with 20 mm nominal size stone aggregate including carriage of material within all leads and lifts as per direction of Engineer-in-charge |
| 60 | Providing and fixing Garsa stone slab12.5 mm.cladding on R.C.C.surface side as on faces of Arch masonry walls etc.on 12mm. thick cement plaster 1:3 (1cement:3sand) and jointed with cement slurry i/c scaffolding etc. complete. |
| 61 | 40 mm thick fine dressed Red Mandana stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand) with joints finished flush. including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 62 | Providing and laying four courses water proofing treatment with bitumen felt over roofs consisting of first and third courses of blown bitumen 85/25 or 90/15 conforming to IS : 702 applied hot @ 1.45 Kg per square metre of area for each course, second course of roofing felt type 3 grade-I (hessian based self finished bitumen felt) and fourth and final course of stone grit 6 mm and down size or peasized gravel spread at 6 cubic decimeter per square metre, including preparation of surface but excluding grading complete with :. complete as per design approved by Engineer-in-Charge. |
| 63 | Providing and fixing 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge. |
| 64 | Providing and fixing ridges or hips 60 cm overall with 0.60mm thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer in Charges. Ridges plain (500 - 600mm) |
| 65 | Providing and fixing valley 60 cm overall 0.60mm thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia with prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-charge. ,North light curves |
| 66 | Providing and fixing Flashing 60 cm overall 0.60mm thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia with prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-charge.:-Gutter (600 mm over all girth) Flashings/ Aprons.( Upto 600 mm) |
| 67 | Providing and fixing Gutter 60 cm overall 0.60mm thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia with prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-charge.:-Gutter (600 mm over all girth)Gutter (600 mm over all girth) |
| 68 | Providing and fixing on wall face PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, Single socketed pipes complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge.:- 110mm diameter metre . |
| 69 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion:- PVC bend 87.5° 110 mm bend. |
| 70 | PVC Door bend 110 mm bend |
| 71 | PVC plain shoe 110mm |
| 72 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge.:- 110mm. |
| 73 | Providing and fixing MS BP sheet 2.00 mm thick in eves board /facia/ soffits/ ceiling including cutting fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge ( base members of steel work shall be measured and paid seperately ). |
| 74 | Providing and fixing angle iron doors frames (Single rebate) manufactured from M.S. angle section of 35x35x4mm and M.S, flat 50x5 as per design and drawing including jambs, lock jambs beeds if required angles threshold of M.S. angle 50x5mm welded or rigidly fixed by mechanical means lugs with split ends tails to each jambs including steel butt hinges 2.5mm thick with a provision of locking arrangements and shock absorbers as specified and applying coat of approved steel primer after pre-treatment of the surfaces as directed by the Engineer-in-charge |
| 75 | Providing and fixing angle iron door frames manufactured from M.S.Angle iron section 25X25X4 mm thickness including hinges jamb,lock jamb,beed and if required angle thrashold of mild steel angle 5X25 mm welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb includingsteel butt hinges 2.5 mm thick with provision for locking arrangementand shock observer as specified and applying a coat of approved steel primer after preteatment of the surface as directed by Engineer-in-Charge. |
| 76 | Providing and fixing steel window made of frame with M.S. channel 75mm X 40mm and M.S. flat 75mm X 4mmin combination welded together and standard section F-7B style of standard size with sash bar or T- section 25mm x 25mm x 3mm and angle iron 25mm x 3mm and joints metred and welded with 16mm x 3.5mm lugs 10cm long embeded in C.C. block 1 : 3 : 6 (1 cement : 3 sand : 6 stone aggregates) or with wooden plug and screw or rawl plug and screw or with clips or with bolts and nuts as required and MS iron fittings completeincluding p/f glass pan 4mm thick in glazed and wire gauge of designation 85 with 0.56mm dia in wire gauge panel with glazing clips and special metal sash putty of approved make complete and applying a coat of approved steel primer after pretreatment of the surface complete job in all respectas per architectural drawing including carriage of material within all leads and lifts as per direction of Engineer-in-charge. |
| 77 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 78 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 79 | Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge.:- M.S. tube. |
| 80 | Providing and fixing mild steel round holding down bolts with nuts and washer plates complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 81 | Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 82 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 83 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ litre. including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 84 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 85 | Wall painting withstain enamel paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 86 | 6 mm cement plaster of mix : 1:4 (1 cement : 4 fine sand) in ceiling complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 87 | 12mm cement plaster on fair side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand) completeincluding carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 88 | 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand) complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 89 | Distempering with Acrylic washable distemper of approved brand and manufacture to give an even shade :New work (two or more coats) over and including water thinnable priming coat with cement primer complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 90 | Distempering withAcrylic washable distemper of approved brand and manufacture to give an even shade in ceiling and slopy roof :New work (two or more coats) over and including water thinnable priming coat with cement primer complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 91 | Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 92 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 93 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 94 | Providing and laying Cement concrete drain with cement concrete 1:3:6( 1 cement : 3 Sand : 6 graded stone aggregate 20 mm nominal size) mechanically mixed in open mix ed in open surface drain with plinth protection having internal size 20 x 15 cm & (twenty into fifteen centimter) with side wall of 10 cm ( ten centimter) thick & inside plastering with CM 1:3 including earthwork & finished with floating coat of neat cement complete as per standard design as per HPPWDspecifiction 1990 volume -1 (one) including carriage of all labour equipments and materials to various location through complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 95 | Providing and fixing 100 mm dia M.S. pipe embeded in CC. block 1:1.5:3 (30x30x40 cm.) including carriage of material in all leads and lifts as per direction of the Engineer in Charge. (Base plate and welding charges etc. measured and paid for seprately) |
| 96 | Providing and fixing 45x45 cmM.S. bracket of frame work 50x50mm & 20mmx20mm M.S. Hollow sections alongwith 12mmx12mm solid square bars in combination as per Arch.Drg. detail i/c carriage of materials within all leads, lifts and other incidentals as per directions of Engineer- in- Charge. |
| 97 | Providing and fixing 20mm dia nominal bore G.I. pipes complete with G.I. fittings including trenching and refilling etc. complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. External work |
| 98 | Providing and fixing 15 mm dia nominal bore G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 99 | Providing and fixing 20 mm (twenty five millimetre) nominal bore G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall including carriage of material in all leads and lifts as per direction of the Engineer in Charge.:- |
| 100 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. :25 to 40 mm nominal bore |
| 101 | Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. (cost of water meter and stop cock to be paid separately). |
| 102 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) RCC. cover with frame (light duty) 455mm x 610mm internal dimensions, , R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 Fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: - Inside dimensions 455mm x 610mm and 45cm deep for single pipe line : With common burnt clay F.P.S. (non modular) bricks of class designation 7.50. including carriage of material in all leads and lifts as per direction of the Engineer in Charge |
| 103 | Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL-PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the engineer in charge. 1216 (16 mm OD) pipe |
| 104 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge.1000 lt. capacity |
| 105 | Providing and fixingPVC floor trapsISI marked ofself cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc.complete including carriage of materials within all leads andlifts:-110 mm x 90 mm |
| 106 | Providing and fixingPVC floor trapsISI marked ofself cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc.complete including carriage of materials within all leads andlifts:110 mm x 75 mm |
| 107 | Providing and fixing High pressure PVC spigot and socked , waste and ventilating pipesISI marked including fixing with approved adhesive etc. complete including carriage of materials within all leads an lifts :-110mm dia |
| 108 | Providing and fixing High pressure PVC spigot and socked , waste and ventilating pipesISI marked including fixing with approved adhesive etc. complete including carriage of materials within all leads an lifts :-75mm dia |
| 109 | Providing and laying 150 mm dia (to level or slopes) and jointing with approved adhesive high pressure PVC spigot and socket waste and ventilating pipe 150 mm dia in trenchesincluding carriage of materials within all leads and lifts. |
| 110 | Providing and fixing M.S.holder bats including steel bolts to sand cast iron/cast (spun) iron pipes embeded in and including cement concrete blocks 100mm X 100 mm X 100 mm of 1:2:4 mix including cost of cutting holder and making good the wall 75 mm dia / size pipeincluding carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 111 | Providing and fixing M.S.holder bats including steel bolts to sand cast iron/cast (spun) iron pipes embeded in and including cement concrete blocks 100mm X 100 mm X 100 mm of 1:2:4 mix including cost of cutting holder and making good the wall 110mm dia / size pipe including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 112 | Providing and fixingPVC single equal branch with oval access door , ISI marked insertion rubber washer 3mm thick bolts and nuts complete including fixing with approved adhesive complete including carriage of materials within all leads an lifts :-110 mm dia |
| 113 | Providing and fixingPVC single equal branch with oval access door , ISI marked insertion rubber washer 3mm thick bolts and nuts complete including fixing with approved adhesive complete including carriage of materials within all leads an lifts :- 75 mm dia |
| 114 | Providing and fixingPVC door band with oval access door , insertion rubber washer 3mm thick bolts and nutsISI marked complete including fixing with approved adhesive complete including carriage of materials within all leads an lifts :-110 mm dia |
| 115 | Providing and fixingPVC door band with oval access door , insertion rubber washer 3mm thick bolts and nutsISI marked complete including fixing with approved adhesive complete including carriage of materials within all leads an lifts :-75 mm dia |
| 116 | Providing and fixingPVC single equal branch plain ISI markedincluding fixing with approved adhesive complete including carriage of materials within all leads an lifts :-75 mm dia |
| 117 | Providing and fixingPVC single equal branch plain ISI markedincluding fixing with approved adhesive complete including carriage of materials within all leads an lifts :-110 mm dia |
| 118 | Providing and fixingPVC collars ISI markedincluding fixing with approved adhesive complete including carriage of materials within all leads an lifts :-75 mm dia |
| 119 | Providing and fixingPVC collars ISI markedincluding fixing with approved adhesive complete including carriage of materials within all leads an lifts :- 110 mm dia |
| 120 | Providing and fixingPVC plain bend ISI markedincluding fixing with approved adhesive complete including carriage of materials within all leads an lifts :- 75 mm dia |
| 121 | Providing and fixingPVC plain bend ISI markedincluding fixing with approved adhesive complete including carriage of materials within all leads an lifts :- 110 mm dia |
| 122 | Providing and fixing PVC cowl including carriage of materials within all leads and lifts as per direction of the Engineer in Charge. :-75 mm nominal diametre |
| 123 | Providing and fixing PVC cowl including carriage of materials within all leads and lifts as per direction of the Engineer in Charge. :- 110 mm nominal diametre :- |
| 124 | Providing and fixing sand cast iron S&S off sets as per IS: 1729:-76 mmoff sets With 75 mm dia pipe including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 125 | Providing and fixing sand cast iron S&S off sets as per IS: 1729:- With 100 mm dia pipe including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 126 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) No. 20012 with seat and lid, 10 litre low level white P.V.C. flushing cistern,No. 21001 including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 127 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) No.20004 with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x400 mmmm with integral type foot rests including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 128 | Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. :Flat back wash basin of size 550x400 mm No.10001 |
| 129 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm No.60002 with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :Single half stall urinal with 5 litre P.V.C. automatic flushing cistern including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 130 | Providing and fixing white vitreous china divison plate of IS No. 5011 for Urinalincluding making all connections excluding cost of fittings : Size 700x340 mm including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 131 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 132 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 133 | Providing and fixing PVC. 110mm size \"P\" or \"S\" trap for water closet (squatting pan) including jointing the trap with the pan and and PVC pipe with approved adhesive etc. complete.including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 134 | Providing and fixing G.I. Union for wash basin or sinkincluding carriage of material in all leads and lifts as per direction of the Engineer in Charge. :-32mm dia |
| 135 | Providing and fixing C. P. Brass S Trap for wash basin and sink including carriage of material in all leads and lifts as per direction of the Engineer in Charge. :32mm dia. |
| 136 | Providing and fixing PTMT. Bottle Trap for wash basin or sink including carriage of material in all leads and lifts as per direction of the Engineer in Charge. :-32mm dia |
| 137 | Providing and fixing C.P. brass waste for wash basin or sink including carriage of material in all leads and lifts as per direction of the Engineer in Charge.32 mm dia |
| 138 | Providing & fixing 32 mm dia, PVC waste pipe for wash basin or sink includingcheck nut including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 139 | Providing & fixing 110mm dia C.P. grating for floor or nahani / gully / floor trap including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 140 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 141 | Providing and fixing 600mm X 20mm size C.P. brass towel rail (heavy duty ISI marked IS:8931 & 8934) complete with C.P. brass brackets fixed to wooden plugs with C.P. brass screws including carriage of materials within all leads and lifts. |
| 142 | Providing and fixing 600mmx120mm glass shelf with C.P. brass bracket and guard rail complete,including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 143 | Providing and fixing charomium plated brass soap dish with C.P. brass brackets fixed to wooden cleats with C.P. brass screws including carriage of materials within all leads and lifts. |
| 144 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge :480x405 mm bowl depth 200mm. |
| 145 | Providing and fixing 15mm dia CP brassbib tap of (heavy duty ISI marked IS:8931 & 8934) including carriage of materials within all leads and lifts. |
| 146 | Providing and fixing 15mm dia CP brasspillar tap of jaquar with capstan head (heavy duty ISI marked IS:8931 & 8934) including carriage of materials within all leads and lifts. |
| 147 | Providing and fixing 15mm dia C.P.brassangle valve of jaquar with flange(heavy duty ISI marked IS:8931 & 8934) including carriage of materials within all leads and lifts. |
| 148 | Providing and fixing 15mm diaC.P.brassstop cocks including carriage of materials within all leads and lifts :- |
| 149 | Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge.:-15 mm nominal bore with 45cm length. |
| 150 | Providing and fixing brass full way valve with wheel including carriage of materials within all leads and lifts :-15mm nominal bore. |
| 151 | Providing and fixing brass full way valve with wheel including carriage of materials within all leads and lifts :-20 mm nominal bore. |
| 152 | Providing and fixing PTMT, push cock of approved quality and colour.15 mm nominal bore, 98 mm long, weighing not less than 75 gms including carriage of materials within all leads and lifts |
| 153 | Providing and instalation Electric Pump 2HP Complete including carriage of meterials in all leads and lifts. |
| 154 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :Inside size 90x80 cm and 45 cm deep including RCC cover with frame455x610 mm internal dimensions, : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 155 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :Inside size 120cm x 90cm and 90cm deep including RCC cover with frame (medium duty) 500mm internal diameter, : With common burnt clay F.P.S. (non modular) bricks of class designation 7.50 complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. |
| 156 | Providing and fixing precast reinforced cement concrete chamber cover with frame complete for man hole of internal dimension 300mm x300mm i/c carriage of materials within all leads, lifts and other incidentals. |
| 157 | Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality complete including carriage of material in all leads and lifts as per direction of the Engineer in Charge. Rectangular shape 610x455 mm internal dimensions. |
| 158 | Providing and laying cement concrete 1:4:8 (1 Cement : 4 Sand : 8 graded stone aggregate 40mm nominal size ) bedding for stoneware pipes of the following internaldiameters, necessary form work and curing complete including carriage of materials within all leads and lifts:- 150mm. |
AI Tender Summary
Tender Timeline
Oct 17, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedOct 28, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedOct 29, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender