Repair Of 10 Seater 6 Nos Mobile Toilets In M.C. Thanesar.
Tender Value
5 Lakhs
Estimated cost
Bid Submission
14 Oct 2022
0 days left
EMD
5000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
thanesar → Haryana
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Repair Of 10 Seater 6 Nos Mobile Toilets In M.C. Thanesar.
BOQ
| Sl. No. | Item Description |
| 1 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required Kitchen sink with drain board 510x1040 mm bowl depth 250 mm [HSR ITEM NO. 22.10.1.1 ] |
| 2 | Providing and fixing brass bib cock of approved quality. 15 mm nominal bore[HSR ITEM NO. 22.96.1 ] |
| 3 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): 65 mm nominal bor [HSR ITEM NO. 22.98.6 ] |
| 4 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass of approved quality complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. [HSR ITEM NO. 22.209 ] |
| 5 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete [HSR ITEM NO.13.29.1] |
| 6 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) [HSR ITEM NO. 13.41] |
| 7 | Painting over the wooden/metal surface with aluminium paint of approved brand and manufacture to give an even shade. Two or more coats on new work [HSR ITEM NO. 11.84.1] |
| 8 | Supply and erection of M.S. angle iron frame duly welded for housing M.S. sheet & main switches etc. on it, fixed on wall by means of suitable size of rag bolts with cement concrete, duly painted with three coats of approved paint including one coat of red oxide. MS STAND, BUS BAR CHAMBER AND PANELS [HSR ITEM NO. 23.24.1] |
| 9 | Providing and fixing precoated galvanised iron profile sheets (size, shape pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length up to 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete up to any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. [HSR ITEM NO. 9.33] |
| 10 | Replacing and fixing bright finished brass flush bolts with necessary brass screws etc. complete. [HSR ITEM 30.63.1] |
| 11 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) For fixed portion Anodised aluminium (anodised transparent ordyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)[HSR ITEM 12.157.1] |
| 12 | Providing and fixingtubeless tyre (600x16) of apollo make including all accessories complete. |
| 13 | Providing and fixing PTMT soap Dish Holder.[HSR ITEM NO. 22.127] |
| 14 | Providing and fixing PTMT Towel Ring.[HSR ITEM NO. 22.118] |
| 15 | Providing and fixing G.I. Pipes including complete G.I. fitings and clamps. [HSR ITEM NO. 22.89.2] |
AI Tender Summary
Tender Timeline
Oct 08, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedOct 14, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedOct 14, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender