Construction Of Health Sub Centre Buildingat Tandi, Tehsil Thunag , Distt. Mandi ( Hp ) . ( Sh:- Construction Of Building Portion , W.S. & S.I. , Septic Tank And Rain Water Harvesting Syatem ) .
Tender Value
74.95 Lakhs
Estimated cost
Bid Submission
12 Oct 2022
0 days left
EMD
1.49 Lakhs
Bank guarantee accepted
Document Fee
2000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
janjehli → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Health Sub Centre Buildingat Tandi, Tehsil Thunag , Distt. Mandi ( Hp ) . ( Sh:- Construction Of Building Portion , W.S. & S.I. , Septic Tank And Rain Water Harvesting Syatem ) .
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means Hydraulic excavator)/manual means over areas exceeding upto any depth and width including getting out and disposal of excavated earth lead upto any lead as directed by Engineer-in-charge.All kinds of soil including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 2 | Excavation work by mechanical means (Hydraulic excavator)/ manual means infoundation trenches or drains etc. any depth including dressing of sides and ramming of bottoms, including gettingout the excavated soil and disposal of surplus excavated soils including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level. Providing and laying cement concrete 1:4:8 (one cement : four coarse sand : eight graded stone aggregate nominal size) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:5:10(one cement : five coarse sand: ten graded stone aggregate 40 mm (fourty millimetre)nominal size) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level. Providing and laying cement concrete 1:5:10 (one cement : five coarse sand: ten graded stone aggregate including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 6 | Providing and laying damp-proof course 40mm (fourty millimetre) thick with cement concrete (one cement : two coarse sand: four graded stone aggregate 12.5mm (twelve point five millimetre)including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 7 | Coursed rubble masonry (first sort) with hard stone in foundation and plinth with :Cement mortar 1:6 (one cement : six coarse sand) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 8 | C/o Dry rubble masonry in breast wall and retaining walls revetment walls and parapets etc. including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 9 | Providing weepholes in brick masonry / stone masonry /plain reinforced concrete abutment, wing wall, return wall with 100 mm (one hundred millimetre) dia PVC pipe extending through the full with of the structures with slop of 1(v):20(H) towards drawing face complete as per drawing and technical specification clauses 614, 709, 1204.3.7including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 10 | Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8 including carriage of material within all leads and lifts and other incidentals including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 11 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floorall level, excluding the cost of centering, shuttering, finishing and reinforcement with M-20 cement concrete 400 Kg nominal size including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 12 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to all level, excluding cost of centering, shuttering, finishing and reinforcement size M-20 cement concrete 400 kg per cum including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 13 | Steel reinforcement for R.C.C. work ready to use \"cut and bend\" rebars of approved make from factory/workshop to construction site including placing in position and binding all complete above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 14 | Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg (one point seven kilogram) per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 15 | 50 mm (fifty millimetre) thick fine dressed local stone flooring over 20 mm (twenty millimetre)(average) thick base of cement mortar 1:5 (one cement : five coarse sand) with joints finished flush. In Plinth Protection including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 16 | Constructing Course rubble hammer dressed \"U\" shape open surface drain with side wall. 15x22 cm (fifteen into twenty two centimetre)in cement mortar 1:6 (one Cement : six Sand) and inside plastring with cement plaster 1:3 (one Cement : three Sand) including earth work and laying 10 cm cement concrete in 1:5:10 (one Cement : five Sand : ten graded stone aggregate) of 40 mm (fourty millimetre)nominal size and 7.5 cm (seven point five centimetre) cement concrete 1:2:4 (one Cement : two Sand : four Graded stone aggregate of 20 mm (twenty millimetre) nominal size) and finished with a floating coat of neat cement complete as per standard design including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 17 | Centering and shuttering including strutting, propping etc. and removal of form for Foundation, footing basis of columns etc. and mass concrete including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 18 | Centering and shuttering including strutting, propping etc. and removal of form for Flat surfaces such as soffits of suspended floors, roofs, landings and the likeFloors etc upto anythickness including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 19 | Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 20 | Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Strutsincluding carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 21 | Centering and shuttering including strutting, propping etc. and removal of form for Stairs, (excluding landings) except spiralstaircases including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 22 | Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 23 | Centering and shuttering including strutting, propping etc. and removal of form for Edges of slabs and breaks in floors and walls in any width. Under 20 cm (twenty centimetre) wide including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 24 | Providing, hoisting and fixing above plinth level up to all level precast reinforced cement concrete in mouldings as in cornices, windows sills etc, including setting in cement mortar 1:3 (one cement : three coarse sand) cost of required centering, shuttering but, excluding the cost of reinforcement, with M-20 cement concrete 400 Kg per cumnominal size including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 25 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge . Extra for providing richer mixes at all floor levels. (Note:-Excess/less cement over the specified cement content used is payable /recoverable separately ) Providing M-30 grade concrete instead of M-25 grade BMC/ RMC. (Note:-Cement content considered in M-30 is @ 340 kg/cum) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 26 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All works above plinth level upto alllevel. Extra for providing richer mixes at all floor levels. (Note:-Excess/less cement over the specified cement content used is payable /recoverable separately ) Providing M-30 grade concrete instead of M-25 grade BMC/ RMC. (Note:-Cement content considered in M-30 is @ 340 kg/cum) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 27 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of gradeFe-500D or more. including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 28 | Stone soling/boulder filling dry hand packed in under floor including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 29 | Providing and laying autoclaved aerated cement blocks masonry with 150mm/ 230mm/300 mm (one hundred fiifty/two hundred thirty/ three hundred millimetre) thick AAC blocks in super structure above plinth level up to alllevel with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in- Charge. (The payment of RCC band and reinforcement shall be made for seperately) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 30 | Brick work with common burnt clay F.P.S. (non modular) bricks of class esignation 7.5 in foundation and plinth in: Cement mortar 1:6 (one cement : six coarse sand) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 31 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : Cement mortar 1:3 (one cement : three coarse sand) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 32 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to all level.Cement mortar 1:4 (one cement : four coarse sand) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 33 | Cement concrete flooring 1:2:4 (one cement : two coarse sand : four graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete 40 mm (fourty millimetre) thick with 20 mm (twenty millimere) nominal size stone aggregate including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 34 | 6 mm (six milimetre) cement plaster 1:3 (one cement : three fine sand) finished with a floating coat of neat cement and thickcoat of Lime wash on top of walls when dry for bearingof R.C.C. slabs and beams including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 35 | 15 mm (fifteen millimetre)cement plaster on the rough side of single or half brick wall of mix 1:6 (one cement: six fine sand) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 36 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately 2nd class deodar wood including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 37 | Providing and fixing 35 mm thick factory made laminated veneer lumber door shutter conforming to IS : 14616 and TADS 15:2001 (Part B), fixing with butt hinges of required size with necessary screws, all complete as per directions of Engineer- in-charge and panelling with panels of 12 mm (twelve millimetre)thick pre-laminated particle board (decorative lamination on both sides) grade - 1, medium density flat pressed, three layer particle board FPT- I or graded wood particle board FPT- I, conforming to IS : 3087, bonded with BWP type synthetic resin adhesive as per IS : 848 and pre- laminated conforming to IS : 12823, Grade 1, Type - II marked : including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 38 | Providing and fixing ISI marked decorativeflush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm (thirty five millimetre) thick including ISI marked Stainless sqm Steel butt hinges with necessary screws . With a peep hole of size 30x30 cm (thirty into thirty centimetre) fixed with 6 mm (six millimetre) glass as per detail including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 39 | Providing and fixing Staneless steel sliding door bolts, ISI marked , with nuts and screws etc. complete 300x16 mm(three hundred into sixteen millimetre) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 40 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 6 mm (six millimetre) thick DOUBLE glass unit, including ISI marked M.S. pressed butt hinge bright finished of required size with necessary screws. 40mm (fourty millimetre) thick 2nd class devdar wood OPENABLE SHUTTER including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 41 | Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm (one point four millimetre) in both directions with wire of dia 0.63 mm (zero point sixty three) for doors, windows and clerestory windows with hinges and necessary screws :35 mm thick shutters 2nd class Deodar wood including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 42 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 6 mm (six millimetre) thick DOUBLE glass unit with necessary screws.40mm thick 2nd class devdar wood including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 43 | Providing and fixing staneless steel tower bolts, ISI marked,with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 44 | 200X10 MM (two hundred into ten millimetre) |
| 45 | 150X10 MM (one hundred fifty into ten millimetre) |
| 46 | 100X10 MM (one hundred into ten millimetre) |
| 47 | Providing and fixing Staneless steel handles, ISI marked,, with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 48 | 125 mm (one hundred twenty five millimetre) |
| 49 | 100mm (one hundred millimetre) |
| 50 | 75mm (seventy five millimetre) |
| 51 | Providing and fixing Staneless steel hasp and staple (safety type) with necessary screws etc. complete 115 mm ( one hundred fifteen millimetre) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 52 | Providing and fixing Staneless steel hanging type floor door stopper with necessary screws, etc. complete including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 53 | Providing and fixing Staneless steel hard drawn hooks and eyes :including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 54 | 250mm (two hundred fifty millimetre) |
| 55 | 200mm(two hundred millimetre) |
| 56 | Providing and fixing ISI marked oxidised M.S. single acting spring hinges with necessary screws etc. complete 150MM (one hundred fifty millimetre) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 57 | Providing and fixing 19mm (nineteen millimetre)thick water proof termite resistant HDMR wood conforming ply wood of ACTION TESA, GREENPLY box including shelves and shutters, the back side of cup board/cabinet shall be 8mm (eight millimetre) thick prelaminated MDF board and all the cut portions of shelves and shutters shall be finished with 1mm thick pre-lamination/ 4mm (four millimetre) thick veneer pasted over shutter to be polished. All internal surfaces of cup board shall be laminated with 1mm mica of approved shade . All cut portion of the shelves shall be finished with 6mm (six millimetre) thick hard wood edging. The shutters of cup board from all sides shall be finished with 6mm/ 12mm (six millimetre/twelve millimetre) hard wood edging including piano hinges and magnetic catcher with in all accessories etc.complete as per given specification including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 58 | Providing and laying full body vitrified floor tiles (premium quality) matte finish in different sizes(thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm (twenty millimetre)thick cement mortar 1:4 (one cement : four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm (three point three kilogram per square metre) including grouting the joints with white cement and matching pigments etc., complete size 600x600 mm (six hundred into six hundred millimetre) of Asian tiles/ Johnson/ Kajaria/ Orient Bell/ Simpolo/ Nitco or its equivalent. with Granite Border 10 cm (ten centimetre) wide of app. shade including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 59 | Providing and laying full body GLAZED vitrified floor tiles (premium quality) (With VC shield technology)in different sizes(thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (one cement : four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm (three point three kilogram per square metre) including grouting the joints with white cement and matching pigments etc., complete size 605x605 mm (six hundred five into six hundred five millimetre) of Asian tiles/ Johnson/ Kajaria/ Orient Bell/ Simpolo/ Nitco or its equivalent including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 60 | Providing and laying Antiskid VITRIFIED MATTE fINISH floor tiles of size 300x300x10mm (Three hundred into three hundred into ten millimetre) thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (one Cement : four Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm(three point three kilogram per square metre) including pointing the joints with white cement and matching pigment etc., complete of Johnson/ Kajaria/ AGT Tiles/ RAK/ Orient Bell or its equivalent including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 61 | Providing and laying Exterior Grade full body vitrified floor tiles (premium quality) matte finish in different sizes(thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm (twenty millimetre) thick cement mortar 1:4 (one cement : four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm (three point three kilogram per square metre) including grouting the joints with white cement and matching pigments etc., complete size 600x600x15 mm (six hndred into six hundred into fifteen millimetre) of Asian tiles/ Johnson/ Kajaria/ Orient Bell/ Simpolo/ Nitco or its equivalent including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 62 | P/F 8 mm (eight millimetre) thick HDFLaminated wooden flooring AC-IV having a good backing layer made up of plastic laminate or melaminemade in superior water Resistant High Density hard wood fibre board make action tesa or its euivalent with all accessories complete including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 63 | Providing And fixing glazed Digital Ceramic tiles 300x600 x 8 mm (three hundred into six hundred into eight millimetre) thick of approved Shade and manufacturer in skirting risers of steps and dado 12 mm (twelve millimetre) thick cement mortar 1:3(one cement : three sand) and jointed with cement slurry including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 64 | Providing And fixing glazed Germ free Ceramic tiles 300x600 x 8 mm (three hundred into six hundred into eight millimetre)thick of approved Shade and manufacturer in skirting risers of steps and dado 12 mm (twelve millimetre) thick cement mortar 1:3 (one cement : three sand) and jointed with cement slurry including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 65 | Providing and laying antiskid full body vitrified floor tiles(premium quality) matte finish in different sizes(thickness to be specified by manufacturer), with waterabsorption less than 0.08 % and conforming to I.S.15622, of approved make, in all colours & shade, inskirting, riser of steps, over 12 mm (twelve millimetre) thick bed of cementmortar 1:3 (one cement: three coarse sand), jointing with greycement slurry @ 3.3 kg/ sqm (three point three kilogram per square metre) including grouting the joint with white cement & matching pigments etc. complete Size of Tile 600x600 mm (six hundred into six hundred millimetre) of Asian tiles/ Johnson/ Kajaria/ Orient Bell/ Simpolo/ Nitco or its equivalent including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 66 | Providing and fixing 18 mm (eighteen millimetre) thick gang saw cut,mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm (twenty millimetre) thick base cement mortar 1:4 (one cement : four coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shade Area of slab upto 0.50 sqm (zero point five zero square metre) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 67 | Providing and fixing 18 mm (eighteen millimetre) thick gang saw cut,mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over (twenty millimetre) thick base cement mortar 1:4 (one cement : four coarse sand) joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. FLAMED GRANITE of any colour and shade Area of slab upto 0.50 sqm (zero point five zero square metre) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 68 | Providing edge moulding to 18 mm (eighteen millimetre) thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 69 | Kota stone slab flooring over 20 mm (twenty millimetre) with 10 cm (ten centimetre) wide marble band (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (one cement : four coarse sand) 25 mm (twenty five millimetre) thick including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 70 | Kota stone slabs 20 mm (twenty millimetre) thick in risers of steps, skirting, dado and pillars laid on 12 mm( twelve millimetre)(average) thick cement mortar 1:3 (one cement: three coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 71 | Providing and laying antiskid Exterior gradefull body vitrified floor tiles (premium quality) matte finish in different sizes(thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (one cement : four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm (three point three kilogram per square metre)including grouting the joints with white cement and matching pigments etc, complete size 450x450x15 mm (four hundred fifty into four hundred fifty into fifteen millimetre) of Asian tiles/ Johnson/ Kajaria/ Orient Bell/ Simpolo/ Nitco or its equivalent including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 72 | Providing and fixing 12mm (twelvemillimetre) thick water proof termite resistant plywood to be cladded with 4mm (four millimetre) thick veneer of approved shade in combination with readymade panels of wood in tongue and groove joint wood to be polishedfixed over Kail wood frame work of size 40X40 mm (fourty into fourty millimetre) with decorative first class kiln seasoned teak wood beading out of size 25X12 mm (twenty five into twelve millimetre)to be polished on edges and decorative first class kiln seasoned teak wood cornice out of 75x60mm (seventy five into sixty millimetre)to be polished( wood frame work of size 40X40 mm (fourty into fourty millimetre)to be measured and paid for separately) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 73 | P/F Wood frame work of 40mm x 40mm (fourty millimetre into fourty millimetre) @ 600X600 mm (six hundred into six hundred millimetre) centre to centre Horizontally and vertically in Kail Wood including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 74 | Providing and fixing 0.62mm (Zero point six two milimetre) thick preprinterd steel sheet in roofing with hot dipped metallic zinc coasted sheet with top coat of regular modified polyester (RNP) organic coating of 20 (Twenty) microns over 5 ( five) miconsprimer coating to back coast of polyester of 5 (five) microns over 5 (five) microns primer coating including fixing with self drilling and self tapping fasten of size 5.5 mm(five point five millimetre) dia and 55 mm (fifty five millimetre) lapcomplete with all accesoriees as required as per the direction of Engineer-in-charge. |
| 75 | Providing and fixing ridges or hips 60 cm (sixty centimetre) overall with 0.60mm (zero point sixty millimetre) thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 (twenty) microns over 5 (five) microns primer coating + back coat of polyster of 5(five) microns over 5 (five) microns primer coating i/c fixing with self drilling and self tapping fasten of size 5.5 mm (five point five millimetre) dia and 55 mm (fifty five millimetre)lap complete with all accessories as required as per the direction of Engineer in Charges. |
| 76 | Providing and fixing valley 90 cm (ninety centimetre) overall 0.62mm (zero point sixty two millimetre) thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 (twenty) microns over 5(five) microns primer coating back coat of polyster of 5 (five) microns over 5 (five) microns primer coating i/c fixing with self drilling and self tapping fasten of size 5.5 mm (five point five millimetre) dia and 55 mm (fifty five millimetre)lap complete with all accessories as required as per the direction of Engineer-in-charge. |
| 77 | Providing and fixing 15 cm (fifteen centimetre) wide, 45 cm (fourty five centimetre) overall semi- circular plain G.I. sheet gutter with iron brackets 40x3mm (fourty into three millimetre) size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete. :0.80 mm (zero point eighty millimetr) thick with zinc coating not less than 275 gm/m2 including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 78 | Providing and fixing M.S. BP Sheet 1.66mm to 2mm (one point sixty six millimetre to two millimetre) thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall beincluding carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge.measured & paid separtely) |
| 79 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, kg railings, brackets, gates and similar worksincluding carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 80 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 81 | Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer.M.S. tube including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 82 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings /wooden frames with rawl plugs screws etc including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 83 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (ten millimetre) gap for thermal expansion. (i) Single socketed pipes. 110 mm (one hundred ten millimetre) diameter including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 84 | Providing and fixing 75 mm x 62.5mm (seventy five millimetre into sixty two point five millimetre) rounded Wooden hand rails in straight length complete in 1st class Indian Teak Wood including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 85 | Providing and fixing decorative teak wood balluster and post to shape out of 7.5 cm X 7.5 cm (seven point five centimetre into seven point five centimetre) of approved sample as per detail, square wrought fixed with ends housed ( square or splay) to hand rail and treads or strings complete including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 86 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 87 | Coupler: 110 mm bend (one hundred ten millimetre) |
| 88 | Single tee without door :110x110x110 mm (one hundred ten into one hundred ten into one hundred ten millimetre). |
| 89 | Bend 87.5° 110 mm bend (one hundred ten millimetre) |
| 90 | 110 mm Shoe (one hundred ten millimetre) |
| 91 | 15 mm (fifteen millimetre) cement plaster on rough side of single or half brick wall of mix: 1:6 (one cement: six coarse sand)including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 92 | 6 mm cement plaster of mix 1:3 (one cement : three fine sand) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 93 | Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives.:New work (Two or more coats applied @ 1.43 litre/ 10 sqm.(one point fourty three litre per ten square metre) Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm. (zero point ninety litre per ten square metre) : New work (Two or more coats applied @ 1.43 litre/ 10 sqm. (one point fourty three litre per ten square metre) Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.(zero point ninety litre per ten square metre) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 94 | Distempering with Water base Washable Acrylic distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat withcement primer including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 95 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm (zero point ninety litre per ten square metre)over an under coat of primer applied @0.75 ltr/10 sqm (zero point seventy five litre per ten square metre) of approved brand and manufacture including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 96 | Finishing with deluxe multi surface paint system for interior and exteriors using primer as per manufactures specification: Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm (zero point ninety litre per ten square metre) over an under coat of primer applied @ 0.80 ltr/ 10 sqm (zero point eighty litre per ten square metre) of approved brand and manufactureincluding carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 97 | French spirit polishing : Two or more coats on new works including a coat of wood filler including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 98 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 99 | Wall painting two coats with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 (fifty) grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 100 | Providing and fixing 18 mm (eighteen millimetre) thick, 150 mm (one hundred fifty millimetre) wide pelmet of coir veneer board ISI marked IS : 14842, including top cover of 6 mm (six millimetre) coir veneer board, nickle plated M.S. Pipe 20 mm (twenty millimetre) dia. (heavy type) curtain rod with nickel plated brackets, including fixing with 25x3 mm (twenty five into three millimetre) M.S. Flat 10 cm (ten centimetre) long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm (one hundred into fourty into fourty millimetre) on both inner side of pelmet and rawl plugs 75 mm (seventy five millimetre) long etc. all complete including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 101 | Providing and fixing water proofing material i.e. Dr. fixit PIDP Roof LW+ or its equivalent in cement mortar in proportion recommended by the manufacturars with in all leads and lifts of material as per direction of engineer in charge |
| 102 | Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality L D- 2.5 Rectangular shape 600x450 mm (six hundred into four hundred fifty millimetre) internal dimensions including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 103 | Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete 110 mm (one hundred ten millimetre) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 104 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 105 | 20 mm nominal bore (twenty millimetre) |
| 106 | 32mm nominal bore (thirty millimetre) |
| 107 | 15 mm nominal bore (fifteen millimetre) |
| 108 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :. 25 to 40 mm (twenty five to fourty millimetre) nominal bore including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 109 | Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete (cost of water meter and stop cock to be paid separately) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 110 | Providing and fixing Polyethelene-AluminiumPolyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the engineer in charge.Concealed work, including cutting chases and making good the wall etc including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 111 | 2532 (32 mm OD) pipe (thirty two millimetre) |
| 112 | 2025 (25 mm OD) pipe (twenty five millimetre) |
| 113 | 1620 (20 mm OD) pipe (twenty millimetre) |
| 114 | 1216 (16 mm OD) pipe (sixteen millimetre) |
| 115 | Providing and fixing Anglo Indian universal WC 2061 of with PVc Cistern 2602P CERA / Hinware or Jaquar including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 116 | Providing and fixing viterous China Water Closet 2008 of size 520x385x390 (five hundred twenty into three hundred eighty five into three hundred ninety) of Cera or equivalentcomplete including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 117 | Providing and fixing viterous China wash basin 10001 Basin In White Shade of Perryware /jaquar/ Hindware/ Ceraor equivalentincluding cutting holes & making good the same and carriage of materials within all leads and lifts :-Of Superior quality including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 118 | Providing and fixing viterous China wash basin Charlotte 1075 with 1175 half pedestal jaquar/ Hindware/ Ceraor equivalentincluding cutting holes & making good the same and carriage of materials within all leads and lifts :-Of Superior quality including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 119 | Providing and fixing vitreous China Flat backurinal 5001 in White Shade ofHindware/ Ceraor equivalentincluding cutting holes & making good the same and carriage of materials within all leads and lifts :-Of Superior quality as per direction of Engineer-Charge. |
| 120 | Providing and fixing Stainless Steel sink no. 1022-XD of praPrayag Polimers or ots equivalent with C.I. brackets and stainless steel plug 40 mm (fourty millimetre) including painting of fittings and brackets, cutting and making good the walls wherever required 510x1040 mm (five hundred ten intoone thousand fourty millimetre) bowl depth 250 including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 121 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 40mm (fourty millimetre) dia including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 122 | Providing and fixing uplasticised PVC connection pipe with brass unions 45 cm (fourty five centimetre) length 15 mm (fifteen millimetre) nominal boreincluding carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 123 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work 40mm (fourty millimetre) dia) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 124 | Providing and fixing 600x450 mm (six hundred into four hundred fifty millimetre) beveled edge mirror of superior glass (of approved quality) complete with 6 mm (six millimetre) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 125 | Providing and fixing C.P.Mixer for kitchen sink with casted swinging CON 309KN jaquar or equavalent complete In all respect including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 126 | Providing and Fixing Soap dish recessed type stainless steel AHS-1531of Jaquar or equivalentcomplete in all respect including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 127 | Providing and fixing Towel Rack with lower hangerNo. AHS-1581H of hotelier series of JAQUAR, or equivalentof superior quality including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 128 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 129 | 25mm (twenty five millimetre) |
| 130 | 20mm (twenty millimetre) |
| 131 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 132 | 15mm (fifteen millimetre) |
| 133 | 20mm (twenty millimetre) |
| 134 | 32mm (thirty two millimetre) |
| 135 | Providing and Placing on terrace (at all floor levels ) polyethylene water storage tank , IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet , outlet and overflow pipes but without fittings and the base support of tank including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 136 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 15 mm (fifteen millimetre) nominal bore including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 137 | Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete 110 mm (one hundred ten millimetre)including carriage of materials with in all leads, lifts and other incidentals asperthe direc |
| 138 | Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete 150 mm (one hundred fifty millimetre) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 139 | Providing and fixing PVC floor trap of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete. 110 mm X 90 mm (one hundred ten into ninety millimetre) including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 140 | Providing and fixing PVC door bend with ovalaccess door, insertion rubber washer 3 mm (three millimetre) thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 141 | 110mm dia(one hundred ten millimetre) |
| 142 | 150 mm dia (one hundred fifty millimetre) |
| 143 | Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 144 | 110mm dia(one hundred ten millimetre) |
| 145 | 150 mm dia (one hundred fifty millimetre) |
| 146 | Providing and fixing PVC plain double equal branch ISI marked including fixing withapproved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 147 | 110mm dia(one hundred ten millimetre) |
| 148 | 150 mm dia (one hundred fifty millimetre) |
| 149 | Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 150 | 110mm dia(one hundred ten millimetre) |
| 151 | 150 mm dia (one hundred fifty millimetre) |
| 152 | Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc.complete including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 153 | 110mm dia(one hundred ten millimetre) |
| 154 | 150 mm dia (one hundred fifty millimetre) |
| 155 | Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 156 | 110mm dia(one hundred ten millimetre) |
| 157 | 150 mm dia (one hundred fifty millimetre) |
| 158 | Providing and Fixing Paper Holder 1553 of Jaquar or equivalentcomplete in all respect including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 159 | Providing and Fixing Cloth Liner 1565 of Jaquar or equivalentcomplete in all respect including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 160 | Constructing brick masonry manhole in cement mortar 1:4 ( one cement : four coarse sand ) with R.C.C. top slabwith 1:1.5:3 mix (one cement : one point five coarse sand (zone- III) : three graded stone aggregate 20 mm (twenty millimetre) nominal size, foundation concrete 1:4:8 mix (one cement : four coarse sand (zone- III) : eight graded stone aggregate 40 mm (fourty millimetre) nominal size), inside plastering 12 mm (twelve millimetre) thick with cement mortar 1:3 (onecement : three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20 mm (twenty millimetre) nominal size finished with a floating coat of neat cement complete as per standard design : including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 161 | Inside size 90x80 cm (ninety into eighty centimetre) and 45 cm (fourty five centimetre) deep including C.I. cover with frame (Light duty) 450x610 mm (four hundred fifty into six hundred ten millimetre) internal dimentions, total weight of cover and frame to be not less than 38 kg (thirty eight kilogram) (weight of cover 23 kg (twenty three kilogram) and weight of frame 15 kg) (fifteen killogram) : including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
| 162 | Constructing soak pit 1.20x1.20x1.20 m (one point twenty into one point twenty into one point twenty millimetre) filled with brickbats including S.W. drain pipe 100 mm (one hundred millimetre) diameter and 1.20 m(one point twenty) long complete as per standard design including carriage of materials with in all leads, lifts and other incidentals asperthe directions of Engineer-in-Charge. |
AI Tender Summary
Tender Timeline
Oct 07, 2022
11:30 IST
Tender Published
Tender notice published.
CompletedOct 12, 2022
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedOct 12, 2022
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender