Irrigation And Public Health Department has published Nhp Renovation Of Distt. Water Testing Lab. Dhalli Colour Washing, Painting And C / O New Granite And Marvel Shelves, Making A New Sampling Media Preparation, Incubation And Chemical Test Lab Room P / F Of Air Conditioner And Well Air Curtain Et. Submission Date for this Tender is 10-10-2022. Air Fittings and Connectors Tenders in Shimla Himachal Pradesh. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | Providingandlaying cement concrete work M25 and curing complete excluding cost of formwork and reinforcement for reinforced concrete work in all leads and lifts complete in all respect as per the direction of the Engineer-in-charge . |
| 2 | Suspended floors, roofs, landings, shelves and their supports, balconies, beams, girders, bressumers and cantilevers up to floor two level. |
| 3 | Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centring, shuttering, strutting and proppingetc. with wooden battens and bellies, height of propping and centringbelow supporting floor to ceiling not exceeding 4 mtrs.and removal of the same for insitu reinforced concrete and plain concrete work complete in all respect in all leads and lifts and to the entire satisfaction of the Engineer-in-charge. |
| 4 | Flat surfaces such as soffits of suspended floors, roofs, landings and the like. i) Floors etc. up to 200mm in thickness |
| 5 | Half brick masonry using 2nd class common burnt clay building bricks in Cement Mortar 1:4 (1 cement:4 sand) including all leads and lifts complete in all respect. |
| 6 | Above 1st floor two level. |
| 7 | 15mmcementplasterinsinglecoatonroughsideofbrick/concrete/stonewallsforinterior plasteringup to floor twolevelincludingarises internal rounded angles,chamfers and/ or rounded angles not exceeding 80mm in girth and finished even and smooth complete in all respect including all leads and lifts. |
| 8 | a) Cement Mortar 1:6 (1cement:6sand) |
| 9 | Providingandlayingmarblework (tablerubbedandpolishedin flooringin 20mmthickbasein cement mortar 1:3 (1cement: 3 Sand)includingjointingwithcementmortar 1:2 (1White Cement:2 marbledust)withanadmixtureofpigment tomatchtheshadeof the marble 20mmthickwhite makrana marble i/c all leads and lifts complete in all respect. |
| 10 | Providing steel reinforcement for RCC work including bending, binding and placing in position completeup to floor two level within allleads and lifts complete in allrespect and to the entire satisfaction of the Engineer-in-chargeTor steel. |
| 11 | Providing andlaying granite stone in flooring 20mm(average) thickness base of cement mortar1:3(1 cemet:3sand)laidover and Jointed withgrey cement slurrymixed withpigment tomatch the shade ofgranitestonei/crubbingandpolishingcomplete 20mm thick i/c all leads and lifts complete in all respect. |
| 12 | Providing and fixing anodized aluminium work for door. windows, ventilators and partitions with extruded built up standard tubular and other sections of approved make conforming to IS-733 and 1285 anodized transparent or dyed to required shade according to IS-1868 (minimum) anodic coating of grade AC-15) fixed with rawl plugs and screws or with fixing clips or with expension hold fastnersi/c necessaryfillingup of gaps at junctions,at top,bottom and sides with requiredPVC/ Neoprene felt etc. Aluminium sections shall be smooth, rust free straight mitred and jointed mechanically where ever required i/c cleat angle aluminium snap beading for glazing/panelling C P brass stainless steel screws. All complete as per the direction of Engineer-in-charge i/c all leads and lifts complete in all respect. |
| 13 | For door, windows, ventilators and glazed partitions frames. |
| 14 | Forshuttersof door , windows andventilators i/c providing and fixinghinges/pivoted and making provisions for fixing of fittings where ever required i/c the cost of PVC/neoprene gasket as required (fittingsandglazing/panellingshallbepaidforseparetely)i/callleadsandliftscompleteinall respect. |
| 15 | Providingandfixingglazinginaluminiumdoor,windows, ventilators, shutters and partition etc.with PVC/Neoprene gasket etc. complete as per architectural drawing and direction of the Engineer-in-charge costof aluminiumsnapbeadingshallbepaidinbasic items ) i/c allleads and lifts complete in all respect. |
| 16 | Glazing with glass panes of 4mm thickness (weigth not less than 10 kg/sqm ) |
| 17 | Providing & fixing aluminium Tower bolts (barreltype) anodized transparentor dyedtorequired shade and colour with screws etc. i/c all leads and lifts complete in all respect. |
| 18 | 250x10mm |
| 19 | Providing and fixing anodized aluminium sliding door bolts anodized colour and shade with bolt and nuts screws etc complete in all respect i/c all leads and lifts. |
| 20 | 300x 16mm |
| 21 | Providingand fixingaluminiumhandlesanodized transparent or dyed to required colour and shade with necessary screws etc. complete in all respect i/c all leads and lifts . |
| 22 | 125mm |
| 23 | Whiteglazedtiles 6mmthickinskirtingrisersofstepsand dado 12mm thick cement mortar1:3 (1cement:3sand) and jointed with cement slurry |
| 24 | Providing and fixing 10mm thick anti skid water proof stain and impact resistant heavy duty vetrified tiles Nitco or equalient 600x600x10mm manufacturedof approved shade and colourin flooring , treads of the steps ad landing laid over 12mm thick cement mortar 1:3( 1 cement:3 Sand) jointed with cement slurry mixed with pigment to match the shade of tilesas required complete. |
| 25 | Providing full moulding in granite work. |
| 26 | Providing and fixing Aluminium die cashbody Tublor Type Universal Hydraulic door closer (having brand Logo with ISI.IS 3564 embassed on the body,door weight up to 36 Kg to 80 Kg and door width from 701 to 1000 mm with necessary accessories. |
| 27 | Grouting the Joints of flooring tiles having joints of 3 mm width,using water proof epoxygroutmixof desiredshadeincludingfilling /groutingandfinishingcompleteasper the direction of Engineer-in-charge. |
| 28 | Size of Tile 600x600 mm |
| 29 | Providingand fixingup-downRoller typeblinds forwindows up to 2.51m widein single colour light shade as per the direction of Engineer-in-charge. |
| 30 | Providing and fixing decorative type cup board with 19mm thick both side laminated ply board with vertical and horizontal support, inner shelfsback side of 6mm thick both side laminated ply board, shutter of 19mm thick ply board one side laminated and another side 1mm thick mica, special type of slow motion hinges, edge taping and decorative type handles, locking arranement etc. including all leds and lift as per direction and satisfection of engineer-in-charge. |
| 31 | Only elevation area to be measured for payment. |
| 32 | P/F of invertor type air conditioner (hot & cold) split type 1.50 tonne capacity including all installation accessories such as copper pipe, insulation pipe, drainage pipe etc. complete making necessary holes and repair the same including all leads and lifts as per the direction of the Engineer-in-Charge. |
| 33 | Providing and fixing of 3feet wide air curtain of makeDolphy, Eureka, Mitzvah make or its equivalent with specifications , remote controlled/Sensors,220 V/50HZ, Input power 410 W , Noise (db): <52, with three blowers, 2 motors , Air speed 22m/s, Air volume 1520 (m³/h) with complete installation , testing and commissioning complete in all respects as per the satisfaction of Engineer-in-charge. |
| 34 | Providing and fixing to wall ceiling and floor galvanised mild steel tubes ( Medium Grade) tube fitting and clamps including making good the wall ceiling and floor witin all leads and lifts. |
| 35 | 15mm nominal bore. |
| 36 | Providing an fixing brass stop -cock in galvanised mild steel tube including necessary fittings such as mild steel galvanisedjam nut, socket etc. cutting and making long screws complete ( water meter and stop -cock to be measured and paid for seperately ) within all leads and lifts. |
| 37 | 15mm nominal bore |
| 38 | Providing and fixing of brass ball valve ( horizontal plunger type) high pressure with polythene plastic floats within all leads and lifts. |
| 39 | 15mm nominal bore. |
| 40 | 20mm nominal bore. |
| 41 | Providing and fixing PVC water storage tank ISI : 12701 marked , G.I. inlet and outlet connections 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting upto all heights above ground level within all leads and lifts. |
| 42 | 1000 litres net capacitytank. |
| 43 | 2000 litres net capacitytank. |
| 44 | Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making goodthe wall and floors etc. complete within all leads and lifts. |
| 45 | 110mmx75mm. |
| 46 | Providing and fixing high pressure PVC spigot and socket, waste and vanitilating pipes ISI marked including fixing with approved adhesive etc. complete within all leads and lifts. |
| 47 | 75mm dia. |
| 48 | 110mm dia. |
| 49 | Providing and fixing PVC door bend with oval access door,insertion rubber washer 3mm thick bolts and nutsISI marked complete including fixing withapproved adhesive etc. complete within all leads and lifts. |
| 50 | 110mm dia. |
| 51 | Constructing chamber 600mmx450mmx600mm inside size with double flapsurface box 400mmx200mmx200 mm ( inside) with locking arrangment & RCC top slab 1:2:4 mix( 1Cement:2 Sand:4 graded stone aggregate 20mm nominal size) 100mm thick foundation concrete 1:5:10 (1Cement:5 Sand:10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 ( 1cement:3 sand) finished with floating coat of neat cement including curing complete with 200mm thick walls of brick masonry in cement mortar 1:5(1cement:5 sand) within all leads and lifts. |
| 52 | Providing and fixing viterious chinalab sink/ wash basin with single hole for piller tap with C.I. or M.S. bracketes painted white including cutting holes in walls and making good the same but excluding fittings within all leads and lifts. |
| 53 | Flat630mmx450mm |
| 54 | Providing and fixingC.P. Brass waste for wash basin or sink within all leads and lifts. |
| 55 | 32mm dia. |
| 56 | Providing and fixing PVC waste pipe for wash basin or sink within all leads and lifts. |
| 57 | 32mm dia. |
| 58 | Providing and Fixing of Body / Eye Washer for chemical lab complete in all respects. |
| 59 | Providing and fixing water filter aqua guard complete in all respect within all leads and lifts. |
| 60 | Providing and fixingPVC connection with brass union:- |
| 61 | a) 300/450 mm length :- i) 15mm nominal bore. |
| 62 | Providing and fixing C.P. brass pillar tap with capstan head :- 15mm dia.within all leads and lifts. |
| 63 | Providing and fixing C.P. grating round of approvedquality and colour with 110mm nominal dia. |
| 64 | Supplying and fixing of following sizes of PVC conduit along with the accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required as per satisfaction of Engineer-in-charge |
| 65 | 20mm Dia |
| 66 | Supplying and fixing of G.I modular boxes of following sizes along with modular switches in recess as required as per satisfaction of Engineer-In-charge :-8 module (120mm*135mm*60mm ) |
| 67 | Supplying and fixing following rating modular switch/socket in the existing switch box/cover plate including connections etc . As required as per satisfaction of Engineer-In-charge . |
| 68 | S.P 5/6 amps one way modular switch |
| 69 | 5 pin , 5/6 amps modular socket outlet |
| 70 | S.P 15/16 amps one way modular switch |
| 71 | 5 pin , 15/16 amps modular socket outlet |
| 72 | Providing and laying of one Each aluminium conductor, PVC insulated and PVC sheathed, armoured/XLPE power cable, working voltage 1100 volts grade direct in ground; to be laid 1 meter below the ground level including excavation sand cushioning, protective covering and refilling the trench etc. of the required size:- |
| 73 | Armoured cable 6 sq. mm (twin core) |
| 74 | Supplying and fixing of following way, single pole and neutral sheet steel MCB distribution board, 240 volts, on surface / recess, complete with tinned copper bus- bar, wireset, neutral link, earth bar, din-bar, detachable gland plate ,blanking plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required:- |
| 75 | Double door-4 way |
| 76 | Supplying and erection of 6 amps. to 32 amps. rating, 10 KA breaking capacity, 240 volts, "C" curves, miniature circuit breaker of following poles in the existing MCB DB complete with onnections etc. as required:- |
| 77 | Double pole. Cat-A. |
| 78 | Distempering (two coats) with oil bond washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coatwithdistemperingprimerofapprovedbrandandmanufacture afterthoroughlybrushingthe surface free from mortar dropping and other foreign matter and also including preparing the surface evenandsandpaperedsmoothprimingcoatwithdistemper primerincludingallleadsandlifts, complete in all respect. |
| 79 | Painting one coat(excluding priming on coat)on previously painted wood and wood based surfaces with enamelpaint to given and even shade including cleaning of all dirt, dust and other foreign matter sand papering and stopping papering and stoppingi/c all leads and lifts complete in all respect . With white enamel paint |
| 80 | Provision for electric wiring |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
