|
| 1 | Automobile/ AUTOMOTIVE |
| 2 | Vernier Caliper Digital0-200 mm |
| 3 | External Micrometer (digital)Range0-25 mm |
| 4 | External Micrometer Range(Manual)25-50 mm |
| 5 | Internal Micrometer Range(Digital)25-50 mm |
| 6 | Dial Gauge (Metric System)with magnetic stand plunger type0.01 mm ( Least Count) |
| 7 | Telescopic Gauge set of 60.313-6\" |
| 8 | Bore Gauge50-150 mm |
| 9 | Feeler Gauge Metric25 blade |
| 10 | Straight Edge400 mm |
| 11 | Divider200 mm |
| 12 | Inside Caliper200 mm |
| 13 | Outside Caliper200 mm |
| 14 | Torque wrench set of 35-225 N-m |
| 15 | Digital Multi Meter0 to 1000 Ohms, 2.5to 500 V |
| 16 | Hydrometer |
| 17 | Depth Gauge Range0-50 mm |
| 18 | Bevel Gauge12\" Blade, 5 minute Vernier Resolution |
| 19 | Battery Charger6 Amp 12 Volt |
| 20 | Tyre pressure Gauge (Hand Held, Digital)0-120 PSI |
| 21 | Hydrolic Jack (Trolley Type)2 ton |
| 22 | Maintanance Tools |
| 23 | Bolts Gr 8, Gr 5, Gr 28, 10, 12, 14, 17 mm |
| 24 | NutsHex Nut , Castle Nut, Wing Nut , Locking Nut , Lug Nut , Speed Nut (Suitable size) |
| 25 | Studs |
| 26 | ScrewsMachine Screws, Sheet Metal Screws(self tapping), Set Screw – (allen wrench/no head) |
| 27 | WashersFlat Washer, Lock Washer (Suitable size) |
| 28 | Roll-pins/Spring-pins |
| 29 | C - ClipsInternal & External 10 each |
| 30 | General Purpose Tools |
| 31 | Double Ended Spanner set |
| 32 | 6 x 7 mm |
| 33 | 8 x 9 mm |
| 34 | 10 x 11 mm |
| 35 | 12 x 13 mm |
| 36 | 14 x 15 mm |
| 37 | 16 x 17 mm |
| 38 | 18 x 19 mm |
| 39 | 20 x 22 mm |
| 40 | Ring Spanner Set |
| 41 | 6 x 7 mm |
| 42 | 8 x 9 mm |
| 43 | 10 x 11 mm |
| 44 | 12 x 13 mm |
| 45 | 14 x 15 mm |
| 46 | 16 x 17 mm |
| 47 | 18 x 19 mm |
| 48 | 20 x 22 mm |
| 49 | Socket Spanner set with |
| 50 | 20 sockets10 mm onwards |
| 51 | T- Handle 12\" |
| 52 | Extension Rod 4\" |
| 53 | Extension Rod 8\" |
| 54 | Ratchet Handle 12\" |
| 55 | Rotating Union Universal Joint |
| 56 | Side Cutting Plier200 mm |
| 57 | Round Nose Plier200 mm |
| 58 | Flat Nose Plier200 mm |
| 59 | Ball Peen Hammer with Handle500 grams |
| 60 | Cross Peen Hammer with Handle200 grams |
| 61 | Screw DriverStraight tip 8\" Long |
| 62 | Screw DriverStraight tip 12\" Long |
| 63 | Phillips Screw Driver8\" Long |
| 64 | Phillips Screw Driver12\" Long |
| 65 | Hacksaw Frame fixed300 mm |
| 66 | Hacksaw bladesFor above Hacksaw Frame |
| 67 | Cold Chisel Flat10 mm |
| 68 | Allen Key set4 mm - 14mm |
| 69 | Oil Cane500 ml |
| 70 | File flat bastard300 mm |
| 71 | File Square Rough300 mm |
| 72 | File flat smooth 2nd cut250 mm |
| 73 | File Rasp Cut300 mm |
| 74 | Emery Paper/Cloth80 grit/ 120 grit/150 grit |
| 75 | Chassie Frame(LMV) (Old)DieselWith cross members. Mounted with engine, clutch, gear box, Rear axle, Front Axle, Propeller shaft and steering gear box with wheels, Motorized |
| 76 | Cut model of any engine (MPFI) Old, Motorized4 cylinders, 1.2 L Cap, Power Approx. 80 kW, with electronic fuel pump, impeller type water pump, catridge type filters, Alternator, self Starter Compressor Thermostat |
| 77 | Live Axle Assly with Differential & Final Drive/ Cut model of same,mounted on standDifferential( bevel geared, trunion, tail pinion, crown wheel) splined axle shaft, hub assly, opposed type taper roller bearing) |
| 78 | Dead Axle Assly with Stub Axle mounted on standFor light Motor Vehicle |
| 79 | Components of Suspension systemLeaf spring Front & Rear,Centre bolt, Shackle bracket, Hanger bracket, U clamp, Shackle Pin |
| 80 | Cut model of Shock AbsorberTelescopic Type |
| 81 | Components of steering System (at least each one) Mounted on standTie Rod, Rack & Pinion assembly, Complete all standard components. |
| 82 | Air Brake System with compressorWorking model with all standard components |
| 83 | Mechanical brake assemblyPedal, Linkage, Cam & Brake shoe, mounted on a board |
| 84 | Hydraulic brake assemblyMaster cylinder, Servo(Vaccum/Press ure), Wheel cylinder, Pipe lines, mounted on a board |
| 85 | Components of Automobile Electrical System (at least each one) Mounted on a board.Ignition sys,Alternator, Self Starter, lighting sys, Head Light, Rear Lights, Stop lights, Wiper motor, Horn with suitable battery standard make |
| 86 | Different coloured automobile cablesBrown, Yellow, White, Green, Blue, Black 2.5 sq mm |
| 87 | Cooling System Components (Mounted on a board)Radiator, Water pump, Cooling Fan, V – belt, Thermostat valve and Hoses. |
| 88 | Lubrication System ComponentsStrainer, Oil pump, PRV, etc. mounted on a board. |
| 89 | Compressor (in working condition)Single acting Reciprocating type, Cap 160 ltr |
| 90 | Gearbox (old) and clutch assembly. Cut SectionSynchromesh, 5 speed |
| 91 | Fuse5A, 10A, 15A, 20A |
| 92 | Some other itemrequired |
| 93 | Projector with screenStandard make with USB port |
| 94 | Working Bench2.5 X 1.20 X 0.65meters |
| 95 | Bench Vice125 mm Jaw |
| 96 | Table for Instructor4 ft. * 2.5 ft. |
| 97 | Chair For InstructorStandard make |
| 98 | Almirah Steel2.5x1.20x0.5 meter |
| 99 | Hand Grinder 55000 RPM |
| 100 | Greace GunSmall |
| 101 | Mallet Hammer500 grams |
| 102 | Screw gauge |
| 103 | Center Punch |
| 104 | Automotive Puncture Repair kitFor Tubeless and Tubed Tyre |
| 105 | Alignment Gauge (Manual)For Toe in/Toe out |
| 106 | First Aid KitWith general first aide things |
| 107 | Fire ExtinguisherABC type |
