Military Engineer Services-MES has published Addn / Altn Cum Special Repair For Upgradation Of Offrs, Jcos & Or Md Accn At Roorkee Stn. - Demolition Of Cement Concrete ( Reinforced ) Of Any Position Not Otherwise Specifically Provided For And Including Reinforcement Required To Facilitate . Submission Date for this Tender is 01-11-2022. Building Work Tenders in roorkee Uttarakhand. Bidders can get complete Tender details and download the document.
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (reinforced) of any position not otherwise specifically provided for and including reinforcement required to facilitate demolition upto and including fourth story and on the roof top/mumty/parapet and removal of debris and rubbish off premises sideMoD land complete all as specified and directed. |
| 2 | Demolition of brick work built in cement mortar in any description and position complete all as specified and directed. |
| 3 | Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc all as directed. |
| 4 | Demolition of cement concrete (un-reinforced) in Ground floors and paving n.exe 15cm thickness ( below or above ground level ) including removal of rubbish out side complex (MOD land), complete all as specifiedand directed. |
| 5 | Dismantling of RCC/ PVC water tanks exc 250 liters and n.exc 500 liters capacity of any condition or type complete all as specified and directed. |
| 6 | Dismantling of Cast Iron pipe/PVC pipeup to 100 mm bore complete all as specifiedand directed. |
| 7 | Dismantling of Cast Iron pipe/ RCC drain pipe/PVC pipeup to 150 mm bore complete all as specifiedand directed. |
| 8 | Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) laid bedded and pointed in any mortar and removal of old tiles from premises complete all as specified and directed. |
| 9 | Dismantling of floor of WC and bath not exc 300mm deep and removing out the cinder/concrete from sunken portion, cleaning of RCC surface to remove dust, loose particle with compressed air or any other suitable method depending on site conditions, grinding any sharp edges etc complete all as specified and directed. (b) Cleaning or RCC surface to remove dust, loose particle etc with compressed air or any other particles or any other suitable techniques on site conditions etc.(c) M&L for a glass fiber reinforced acrylic modified cementitious coating system with base coat@ 1.50 Kg/Sqm glass fiber reinforcement and top coat with Sika Top® Seal-107 @ 1.50 Kg/Sqm or equivalent of Fosroc or MC Bauchemie India Pvt Ltd.(d) M&L for protection plaster 15mm thick on cement mortar 1:3 admixed with appropriate integral water proofing compound with as specified.(e) M&L for providing 25mm dia GI pipe spout projecting at least 150mm beyond outer face of wall.(f) M&L for sunken portion filled with 40 mm graded brick bats and finished with 50 mm thick PCC 1:2:4 type B1 all as specified and directed.(g) The area of Each WC portion is n.exc 2.00Sqm each.(h) Cost of the above aspect shall be deemed to be included in the quoted rates of the respective item and nothing extra shall be paid on this account.Note : The work will be executed by authorised manufacturers/applicator. |
| 10 | M&L for cutting chases on brick or concrete surface for concealed water tubing or girth n.exc 10cm including making good of disturbed surfaces with PCC 1:2:4 type B0 using 12.5 mm graded aggregate cement mortar 1:3complete all as specified and directed. |
| 11 | Dismantling of Brick tiles or terracing tiles, single layer on roofs, kerbs, aprons, etc. (each layer) and removal of rubbish out of defence land complete all as specified and directed.(Note : All roots of plant on either on wall or roof to be removed and making good the disturbed surfaces. The rate quoted be the contractor is deemed to be included in the unit rates.) |
| 12 | Demolition of Mud Phuska in roofs,any thickness including plastering and leeping of any thickness upto 30cm deep complete all as specified and directed.(Note: All roots of plant on either on wall or roof to be removed and making good the distributed surfaces. The rate quoted by the contractor is deemed to be included in the unit rates including removalof mud phuska outside defence land.) |
| 13 | Taking up or down 15 mm bore GI tubing and connections including cleaning for re-fixing complete all as specified and directed. |
| 14 | All as per item No. 13 above but 20 mm bore |
| 15 | Taking down chowkhat or frames exc. 1.5 Sqm and n.exc 4 Sqm eachwith shutters (without taking off shutters from frames) complete all as specified and directed. |
| 16 | Taking down chowkhat or frames not exc. 1.5 Sqmeachwith shutters (without taking off shutters from frames)complete all as specified and directed. |
| 17 | Taking down shutters of any description exc 1 sqm and not exc 2 sqm eachcomplete all as specified and directed. |
| 18 | Taking down cement plaster, terrazzo dado in any thickness from brick or stonewalls etc including raking out joints, hacking for key, scrubbing down with water etc including removal of rubbish, vegetation etc outside complex (MOD land) complete all as specified and directed. |
| 19 | M&L for PCC (1:2:4) Ty B-0 using 12.5mm thick course aggregate as incills, steps, parapets,, copings, andthe like including weathering, slightly rounded or chamfered angles and throating, as directed |
| 20 | Dismantling structural steel work including doors, gates, railings etc, but excluding framed truss etc. |
| 21 | Supply & fixing pressed steel frames for doors with one or more rebates including necessary fitting lugs, hinges, lock strike plates etc completed size of frame 165x60mm made out of 1.25mm MS sheets including PCC 1:2:4 Ty B0 using 12.5mm graded stone aggregate as in frame complete all as specified & directed. |
| 22 | Supply & fixing pressed steel frames for doors with one or more rebates including necessary fitting lugs, hinges, lock strike plates etc completed size of frame 105x60mm made out of 1.25mm MS sheets including PCC 1:2:4 Ty B0 using 12.5mm graded stone aggregate as in frame complete all as specified & directed. |
| 23 | S&Ffactorymade mild steel shuttershallbemadeoutofangleiron35x35x5mmand 3 nos 25x25x3mm as cross support in frame of door and covered with 1.00mmthick MS sheet, running welding with frame, with locking arrangement including two coats of synthetic enamel paint over a coat of red oxide as shown on drawing all specified and directed by Engr-in -charge. |
| 24 | S&F 35mm thick Glazed and skeleton shutters using second class hard wood, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats |
| 25 | S&F30mmthickFlush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides. |
| 26 | M&Lfor built in steel cup board with pressed steel frame of size 75 mmx45mmx1.25 mm th with pressed steel shutter 1mm th Godrej pattern fixed to masonry wall by hold fast made out of 25x3 mm flat iron including ms hanging rod of 10 mm dia with bracket fixed on inner side of one leaf of shutter and on other leaf provision of ms peg set of 3 pegs including spray including locking arrangement painting with two coats of synthetic enamel paint over one coat of red oxide primer with two coats of synthetic enamel paint over one coat of red oxide primer all around on steel surface of frame & shutter and making good disturbed portion in cm 1:3 or pcc 1:2:4 complete all as specified. |
| 27 | S&Ffactorymadegaugedshuttershallbemadeoutofangleiron35x35x5mm (outer frame)and25x25x5mm (middle rail 2 nos, 150 mm apart from each other)and 1.0mmthick steel sheet covering on middle rail,10mmSquarebars@ 100mm C/C fixed vertical as grillcompletewithstainlesssteelflyproofwiremeshhaving0.63mm nominal dia wire and 1.4mm average with aperture, with locking arrangement including two coats of synthetic enamel paint over a coat of red oxide as shown on drawing all specified and directed by Engr-in -charge. |
| 28 | S&F 100 mm long(size) butt hinges, stainless steel AISI 304 grade with brass/bronze hinge pin, complete all as specified and directed. |
| 29 | All as per item No. 28 above but 75 mm long. |
| 30 | S&F 300mm long, stainless steel of AISI 304 grade,sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts complete all as specified and directed. |
| 31 | S&F Stainless steel of AISI-304 grade barrel tower bolt 200 mm long, extruded sectioncomplete all as specified and directed. |
| 32 | All as per item No. 31 above but 150 mm long. |
| 33 | S&F Extruded aluminium alloy handles, fabricated type, anodised of size 150mm size long complete all as specified and directed. |
| 34 | S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor of 140mm long complete all as specified and directed. |
| 35 | M&L Preparation of new or previously untreated wood and wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 36 | M&L Preparation of new or previously untreated steel and steel based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 37 | M&L Preparation of old untreated steel and steel based surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint.complete all as specified and directed. |
| 38 | M&Lforpowdercoatedaluminiumanodisedwindowsliding type(3shutterstype)withsashbars, aluminium sections weighing 0.55 Kg/m(min) including stainless steel wire mesh , necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws suitable anodised fittings such as, hinges, handles, including anodised aluminium frame, including S&F 5 to 6 mm thick plain glass and all as specified & directed by Engr-in-charge. |
| 39 | M&L for powder coated (50 micron thick) aluminium ventilator fixed type (partly glazed and partly gauzed) with gasket, glazing clip etc, weight of frame not less than 0.55 Kg/RM and weight of shutter frame not less than 0.425 Kg/RM including necessary joining cleats,rubber packing, anodised aluminium snap beading, screws suitable anodised fittings such as, hinges, including S&F 3 to 4 mm thick pin headed glass complete all as specified and directed. |
| 40 | S&F for powder coated (50 micron thick) aluminium grill of mesh size 50mm x50mm of 8mm thick, Complete all as specified and directed. |
| 41 | M&Lfor18to20mmthickUdaipurgreenStonefactorymadebullnosed,polished(tablerubbedand polished)asinjambs,windowcills,cookingplatformandthelikeetcincementmortar1:4including pointing in white cement (1:2) using marble dust and admixture of pigment to match with shade of stone including rubbing and polishing over and including 10 mm thick rendering in cement mortar 1:4 including rounding of edges, making hole for gas pipe complete all as specified and directed. |
| 42 | M & L brick work with sub class "B" bricks straight or curved on plan exc 6 m mean radis built in CM 1:6 |
| 43 | M&L for Brick work with "B" bricks straight or curved on plan to any radius in half brick thick wall built in CM 1:4 completeall as specified and directed. |
| 44 | M&L for mild steel TMT bars of 10 mm dia and over cut to length bent to shape required including cranking, bending etc and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 45 | M&L for providing reinforced cement concrete(1:2:4) type B-1 using 20 mm graded crushedstone aggregate as in kitchenslab and similar work all as specified and directed. |
| 46 | M&L for providing reinforced cement concrete(1:2:4) type B-1 using 20 mm graded crushedstone aggregate as inChajjas |
| 47 | Form work to sides and soffits of shelves etc including supports such as kitchen shelves, platforms and similar works rough finish surface of concrete (the thickness of slab/shelves n.exc. 100 mm) complete all as specified and directed. |
| 48 | Formwork to chullah hoods, chajjas, troughs and similar items including edges all as specified. |
| 49 | M&L Rendering 5mm thick plastering in cement mortar 1:3 as in ceiling finished even and smooth without using extra cement to match with existing surface complete all as specified and directed. |
| 50 | M&L Rendering 12 mm thick in cement mortar 1:6 on fair face of brick work/ concrete surfaces (either surfaces) of wall and finished even and smooth without using extra cement complete all as specified and directed. |
| 51 | M&L Rendering 5 mm thick in cement mortar 1:4 laid over a layer of 10mm thick rendering in cement mortar 1:6 on fair face of brick work/ concrete surfaces of wall with water proofing admixture in topping layer @ 2% Wt of cement finished even and smooth without using extra cementcomplete all as specified and directed. (WPC will be measured and paid separatly) |
| 52 | M&L Non - skid coloured ceramictiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, set and jointed in neat cement slurry and pointed in white or coloured cement over and including 15mm thick screed bed in CM 1:6 complete all as specified anddirected |
| 53 | M&L Coloured Glazedtiles 300x600 x 7 to 8mm thick,as in vertical surfaces of wall suchas dado/skirting, set and jointed in neat cement slurry and pointed in white or coloured cement over and including 10mm thick rendering in CM 1:4 completeall as specified. |
| 54 | M & L for 16-18 mm thick mirror polished Machine cut kota single piece stone slab of size 22""x22"" for flooringover cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slablaid over and including 15mm thick screed bed in CM 1:6 |
| 55 | M&L kota stone mirror polishedslab with uniform texture of 16-18 mm thick in trader of steps (to be flushed and provided with three Nosof grooves at the end on each step), riser of steps, skirting, dado and pillarsin one single piece (size decided by Engineer-in-Charge) laid over and including cement screed 10mm thick in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing andpolishing , bevelled edge of corner etc complete all as specified and directed. |
| 56 | S&F 15mm bore GI tubing medium grade with all fittings and fixed to wall and ceilingconcealled or laid in floors etc complete all as specified and directed. |
| 57 | All as per item No 56 above but 20 mm bore. |
| 58 | S& F PVC (SWR) vent cowl suitable for 75 mm pipe |
| 59 | S&F white colour Rotational moulded polyethylene water storage tank 500 liters capacity,ISIMarked white triple layer construction (cylindrical vertical closed top), hoisted & fixed in position including all fittings ISI Marked complete all as specified and as directed. |
| 60 | S&F in repair vitreous chinaware coloured wash hand basin (WHB)size 550mm x 400mm, Ist quality,including provision of pair of mild steel angle iron brackets of suitable size duly painted and cutting for and pinning in ends of brackets in walls & making good & including providing and fixing of suitable heavy duty waste pipe and waste fitting complete all as specified and directed. |
| 61 | S&F in repairs PVC duel action symphonic action type flushing cistern 10 ltr capacity, low level, white with inlet, ball valve and floatincluding brackets and flush pipe. |
| 62 | S&F in repair sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed. |
| 63 | S&F sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe,overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm Complete all as specified and directed. |
| 64 | S&F in repair Chromium platedtubular towel rail, 25mm dia, ‘D’ type 60cm long between flanges of brass chromium platedand with hooks,brackets & End caps fixed with brass screws complete all as specified and directed . |
| 65 | S&F in repair stainless steel peg set of six complete all as specified and directed. |
| 66 | S&F in repair 15 mm dia stop cock/angle cockcast copper alloy chromium plated screwed downhigh pressure with crutch or butterfly handle,with long shank and cup (concealed type), flenchscrewed both ends for iron or for union.fixed in repair (make: Cera new cat no F2002201, Jaquar cat no CON-CHR-053 KN, Pearl cat no ARI-004 ) . |
| 67 | Supply & fix wall mixer including over head shower chromium plated for mixing hot and cold water screwed for iron pipe suitable for 15mm borepipes complete all as specified and directed. (Make Jaquar Florentine FLR-CHR-5273 UPR, Pearl GPR-884, CERA-F1017401) |
| 68 | S&F in repair bib taps brass cromium plated 15 mm bore size screwed down screwedfor iron pipe or for brass ferrule (make: Cera cat no F1015151, Jaquar cat nocontinental CON-CHR-047 KN, Pearl cat no ARI-003 ) |
| 69 | S&FinrepairBrasschromiumplatedshowerrose125mmsizeallasspecifiedanddirected(make: Jaquar/cera/pearl or equivalent) |
| 70 | S&F in repair Stainless steel grating 100mm dia of best quality as approved by GEincluding fixing in CM1:4to floor/nahani traps etc complete all as specified anddirected. |
| 71 | S&F in repair Gun-metal globe or gate valves 20mm bore with iron wheel head, screwed both ends for ironcomplete all as specified and directed. |
| 72 | S&F 20 mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed (Minimum weight210 gms) complete all as specified and directed. |
| 73 | S&F in repair Looking mirror 600 x 450 mm beveled edge 5.5 mm thick selected quality glass, mounted on 6 mm thick commercial ply, aluminium frame around and fixed to wooden plug with CP brass screws and cup washerscomplete all as specified anddirected. |
| 74 | S&F in repair PVC connection 15 mm bore and 45cm long with washers complete all as specified and directed. |
| 75 | S&F in repair Stainless steel cromium plated Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed. |
| 76 | S&F PVC (SWR) pipes of 110 mm nominal outside diameter (Type B with wall thickness 3.20 to 3.80 mm) single socketed in any length with rubber ring joints including all fittings/fixtures fixed on wall or in trenches or in floor complete all as specified and directed. |
| 77 | All as per item No. 76 above but 75mm nominal outside diameter. |
| 78 | S&F PVC (SWR) junction, 110mm dia (double T) L equal or unequal provided with access door complete all as specified and directed. |
| 79 | S&F PVC (SWR) 75mm dia (single T) or unequal provided with access door complete all as specified and directed. |
| 80 | S&F 110 mm bore PVC (SWR) bends/shoes any radius completeall as specified and directed |
| 81 | All as per item No. 80above but 75 mm bore. |
| 82 | S&F in repair PVC (SWR) 110 mm Nahani trap with grating includingjointing to waste pipe in cement concrete complete all as specified and directed. |
| 83 | S&F in repair PVC (SWR) floor trap, 75mm dia plain including jointing with solvent cementwith grating includingjointing to waste pipein cement concrete complete all as specified and directed. |
| 84 | S&F in repair PVC branch piece single (equal or unequal) 110 mm bore ordinary or inverted (spigot or sockettype) or with parallel branches inclaccess door acomplete all as specified and directed |
| 85 | S&F PVC (SWR) reducers 110mm dia, complete all as specified and directed. |
| 86 | S&F in repair 110 mm pipe stackclamps out of 50mmx 5 mm flat iron includingbolts and nuts and securing ends of stays to walls or roofcomplete all as specified and directed. |
| 87 | All as per item No. 86 above but 75 mm bore pipe. |
| 88 | M&L 75mm thick cement concrete 1:3:6 type C2 (using 40mm graded stone agg). Plinth protection laid to a slope of 1 in 24 in alternate basis system. Each bay shall not exceed 3m in length. 12mm wide & 75mm deep joint shall be formed between the bays which shall be filled with mastic filling to full depth comprising a mixture of 1 part of hot blow bitumen 85/25 portion and two parts of heated badrapur sand (by volume) etc complete all as specified and directed. |
| 89 | M&L for 75mm thick cement concrete (1:4:8)type D-2,using 40mm graded stone aggregate as in sub base. |
| 90 | M&L Cement concrete1:2:4 type B0(using 12.5mm graded crushedstone agg) asin roof leveling, finished even and fair, complete all as specified and directed |
| 91 | Cutting into existing manholes for connecting new drains making good to pipe and rendering,cutting out existing benchingfor and forming branch channel (1/2 or 3/4section ) in cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate finished smooth and reforming benching as required for 100/150mm dia pipes complete all as specified and directed. |
| 92 | M&L Frame work as in door chowkhat with angle ironwelded together ends of angle shouldered and fixed to opening and welding 3 Nos mild steel butt hinges, and 6 nos hold fasts made out of FI 25x3 mm 30 cm long for fixing of chowkhat( Butt hinges paid separately)complete all as specified and directed |
| 93 | Material & labour for cleaning of concrete or plasteredsurfaces of roof and applying priming coat using with bituminous primer @ 0.30kg per Sqm followedevenly by a tack coat @ 1.20 kg per Sqm using 85/25 grade industrial hot blown bitumen, over it laid with 3mm thickAPP modified polymeric waterproofing membrane minimum weight 3.6 Kg per Sqm reinforced with non-woven polyester fabric (weightnot less than160GmperSqm)unrolled& bondedtosubstratewithsideandendlaps75mm & 100mm asper manufacturer’s instruction andapplying over it a tack coat using 85/25 grade industrial hot blown bitumen@ 1.20 kg per Sqm and finally finished the top of polymericwater proofing membrane with a coat ofbituminousaluminumpaint@0.20kgperSqmaspermanufacturer’sinstructions over,completeallas specified & directed. (including removal of existing membrane and removal of scrape from site) |
| 94 | Supply only liquid water proofing compound complete all as specified and directed. |
| 95 | M&L Cement concrete type B1-1:2:4 (using 20 mm graded crushed stone agg) in roof kerbs or mud stop rounded or chamfered on edge etc complete all as specified and directed |
| 96 | S & F 25mm MS steelcurtainrod covered with PVC coatingwithfancy typebraket andend caps completeallasspecifiedand directed. |
| 97 | M&L for complete removal of existing treatment on surfaces of walls by scrapping down with mechanical grinderon old walls as per the specification of manufacturers instructions of paints/OBD complete all as specified and directed. |
| 98 | Preparation of new plastered surface or old treated surface of wall by applying 2mm thick wall care putty and making the surface smooth and applying two coat of oil emulsiondistemper using roller for painting complete all as specified & directed. |
| 99 | M& L preparing plastered new surfaces of ceiling and applying three coats of white wash on ceiling surface |
| 100 | All as ser item No.99 above but one coat on old ceiling surface. |
| 101 | M&L Preparation of newly/old plastered surfaces of walls and applying two coats of colour wash on walls complete all as specified and directed. |
| 102 | S&F in repairs 15mm bore Pillar tap of Chromium plated high pressure screwed for iron pipe and fixed etc. complete all as specified and directed. |
| 103 | 25mm thick Flush shutters, solid core construction, withpartical board core and plywood face panels, commercial type on both sides |
| 104 | S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised with width of flap 40mm |
| 105 | Hasp and staple,mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws, 100mm |
| 106 | S & F Magic eye piece to door shutter |
| 107 | Supply and fix glass corner shelf fancy type made of 6 to 7 mm thick sheet glass of size 250mmx250mm fixed with chromium plated brackets complete all as specified and directed. Make : fortune or equivelent |
| 108 | Taking up or down 15mm bore steel tubing and connections, including cleaning and refixing old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) |
| 109 | All as per item No 108 but 20mm bore |
| 110 | S&FStainless steel 4 shelf wall mounted kitchen utensils rack, Dish rack with plate,& cutlery stand of size 18x24 inches , fixed to wall plugs andchromium plated brass screws complete all as specified and directed. |
| 111 | S&F in repair of vitreous china squatting pan ‘Orrisa pattern’ size 580 x 440 mm white with integral foot rest includingreplacementof‘P’or‘S’traplimeconcretebeddingandmakinggoodfloorcompleteallas specified and directed. |
| 112 | S&Fjoint free non skidceramic tiles coloured of7 to 8 mm (squre/ rectungular ) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors set and jointed inneat cement slurry and pointed with whiteor coloured cement over and including 15mm thick screed bed in cement mortar 1:6complete all as specified and directed. |
| 113 | All as per item No 112 above but as in skirting over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed. |
| 114 | M & L for cutting of bushes small trees (Peepal small plants etc) trunks shrubs of any dia and girth from roof projection, chajjas , wall junction parapet etc at any height by necessary demoliton of brick work etc if requriedandmakinggooddistrubedsurfacestomatchwithexistingfiniheswithandinclmaterialand laboreinCM1:4mixedwithWPC/PCC1:3:6typeB0/BkworkinCM1:4asrequiredatsiteandas directed by Engr-in-Charge |
| 115 | M&Lprecastreinforcedcementconcrete1:2:4typeB1(using20mmgradedstoneaggegrate)asin Chullahhoodchajjaandkitchen or CB shelvesetcsetincementmortar1:6.includingall neccesary formwork & finishing exposed concrete surface all as specified and directed |
| 116 | Supply and fixing PVC heavy duty waste pipes of 40/32mm bore suitable for wash hand basins/sinks/flushing cistern complete all as specified & directed |
| 117 | M&L for pre-laminated ply board 18 to 19 mm thick of density not less than 600 Kg/Cum fixed with screws & approved adhesive of good quality forcabinetcarcase and shelves as per sketch approved and both sides covered with 0.80 mm thick decorative laminates, ""Mica" type 1 of surface finished,colour and pattern as approved as per makers instructions complete all as specified & directed. |
| 118 | S&F Auto hinges for cabinet case (Make ; KARF / HETICH) complete all as specified & directed. |
| 119 | S&F 150 mm size stainless steel bright finish handle for cabinet shutter |
| 120 | Taking down old existing water proofing treatment from the top of RCC / arch slab, including taking down exsiting PCC padding or plaster and hacking the top of RCC slab, cleaning with water and disposal of rubbish off the premises complete all as specified and directed |
| 121 | Material and labour for 20mm thick cement paster in CM 1:4 mixed with WPC @ 2% by weight of cement finished even and fair withour using extra cement on roof surface and wall (WPC will be measured and paid seperately as supply only rate) |
| 122 | M&L for 75mm thick PCC (1:4:8) ty D-2 using 40mm graded stone aggregates as in levelling course below floor tiles in bathroom and WC. |
| 123 | M&L for cutting hole of 230x230x230mm in walls, filling with PCC (1:2:4) Ty B-1 using 12.5mm thick stone aggregate incl fixing of 1Nos angle iron of size 50mmx50mm x6mm, 1m long each incl running welding with other angle, incl 2 coat of synthetic enamal paint over a coat of primer over exposed steel surfaces for cooler stand,complete all as specified and directed |
| 124 | M&L for cleaning of concrete or plastered roof surfaces and applying priming coat using bituminous primer @ 0.30 kg per sqm followed evenly a tack coat @ 1.2 Kg per sqm using 85/25 grade industrial hot blown bitumen over it laid 3 mm thick APP modified polymeric water proofing membrane minimum weight 3.6 Kg per sqm reinforced with non-woven polyester fabric (weight not less than 160 gm per sqm) rolled & bonded to substrate with side and end laps 75mm & 100mm as per manufacturer"s instruction and applying over it a tack coat using industrial hot blown bitumen 85/25 grade @ 1.20 Kg per sqm and finally finished the top of polymeric water proofing membrane complete all as specified and directed. (Note:- Dismantling & Romoval of existing old water prrofing menbrane deemed to be included in quoted rate of this item) |
| 125 | M&L for 40mm thick brick tiles laid on cement mortar (1:6) and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement on mud phuskacomplete all as specified and directed. |
| 126 | All as per item 125 above but except tiles. |
| 127 | Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out soft and loose soil. |
| 128 | M & L Hard core of broken bricks, broken to gauge n exc 63 mm. |
| 129 | M & L 100mm thick cement concrete type C-2, 1:3:6 (40mm graded aggregate),as in sub base. |
| 130 | Supply and laying sand (25 mm thickness ) for cushioning to interlocking paver block complete all as specified and directed. |
| 131 | M&L Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as spfd & directed. |
| 132 | M&L for 60 mm thick Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of M-35 Grade made with grey cement and pigment complete all as specified and directed (Make:-ECO/KRISHNA) . |
| 133 | M&L Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed. |
| 134 | Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm,in soft loose soil. |
| 135 | Cement concrete (1:2:4) ty B1 using 40mm graded stone aggregate as in foundation,filling and mass concrete. |
| 136 | M&L for Aluminium sheet, 0.5 mm thick, fixed in repair with steel screws complete all as specified and directed. |
| 137 | M&L forCement concrete tiles 25cm x 25cm x 20mm thick, using gray cement with pigment, machine pressed; set jointed and pointed in neat cement slurry in floors, and cut and polished over and including 15mm thick cement mortar 1:4. |
| 138 | S&F PVC (SWR) junction, 110mm dia (Single T) or unequal provided with access door complete all as specified and directed. |
| 139 | S&F PVC (SWR) 75mm dia (Double T) or unequal provided with access door complete all as specified and directed. |
| 140 | S&F Fiber glass reinforced plastic (FRP) Flush door in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing offittings and polyurethane foam (PUF) polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameter of FRP, laminate confirming to table 3 of IS -14856 Complete all as specified by the manufacturer and as per direction of Engineer -in- charge. |
| 141 | S&FFRP doorframesthreeleggedofcrosssection90x45mmhavingsinglerebate32mmx15mm.The laminated door frame moulded with fire retardant grade unsaturated polyester resin and chopped mat. Door framelaminatedshallbe2mmthick,frameshallbe coveredwithfiberglassfromallsidesmsflatiron 25x3mm shall be provided at the bottom to steady the frame including PCC 1:2:4 Ty B0 using 12.5mm graded stone aggregate as in frame, complete all as specified and directed. |
| 142 | M&L Coloured vitrified tiles 600mm x 600mm x10 mm thick , joint free asin floors over and including 15mm thick screed bed in CM 1:6 completeall as specified and directed. |
| 143 | M&L Colouredvitrified tiles 600 mm x 600 mm x 10 mm thickas in skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 completeall as specified anddirected. |
| 144 | S & F in repairs vitreous china wash down water closet pan (Pedestal pattern) white incl "P" or "S" trap (Make : Parryware/Hindware) and making good the disturbed surface to match with the existing complete all as specified and as directed. |
| 145 | S & Fplastic water closet (EWC) seat cover white closed pattern with flat bottom and cover incl mild steel chromium plated hinging device complete all as specified and directed. (Make : Parryware/ Hindware). |
| 146 | Dismantling of RCC/ PVC water tanks exc 500 liters and n.exc 1000 liters capacity of any condition or type complete all as specified and directed. |
| 147 | S&F white colour Rotational moulded polyethylene water storage tank 1000 liters capacity, white triple layer construction (cylindrical vertical closed top), hoisted & fixed in position including all fittingscomplete all as specified and as directed. |
| 148 | M&L for Roof trusses (framed), trussed,purlins, crane gantries, rails and fastenings and heavy bracketframing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. |
| 149 | M&L for Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates specified complete all as spfd & directed. |
| 150 | M&L for writing letters of figures (Block.Roman, Italic or Indian) n exc.30 cm high |
| 151 | S & F Health Faucet 8 mm dia 1.2 mtr long flexible tube & wall hook complete all as specified and directed (Model : ALD-573, Make : Jaguar OR EQUIVALENT RANGE OF MARC, JOHNSON). |
| 152 | S & Fbrass CP mixer ( basin mixer) for mixing hot & cold water screwed down for 15 mm dia iron pipe complete all as specified and directed (Model : 8951 Make : PrayagOR EQUIVALENT RANGE OF Jaquar, JOHNSON). |
| 153 | S & F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm |
| 154 | E/M PORTION M & L for concealed Point wiring with 1.5 Sqmm(Nominal area) PVC insulated, unsheathed FRLS multi stranded copper conductor single core cable 1100 Volt grade drawn through and including PVC conduit of 20 mm diaISI marked with complete accessories, including modular type galavanised iron steel sunken 2.5mm thick boxes suitable for switches, sockets, hylum sheet of thickness 3mm, with metal junction box,also including PVC insulated and unsheathed single core multi stranded copper conductor cable of size 2.5 sqmm green in colour as earth continuity conductor connected to common earth dolly, including taking down of existing point wiring and their connected fittings & fixtures like switches, sockets, Ceiling rose, fan regulator etc and making good to disturbed surface with white wash or any type distemper as per existing colour of building , complete all as specified and directed for the following :- Note for Point wiring:- (i) The quoted rate is deemed to be include the price of G Isunken box for switches, sockets etc of any size & shape. (ii)The quoted rate is deemed to be included rate of dismantling of existing point of any type including fittings & fixtures complete. Make of Cable- Havells lifeline / polycab / Plaza, Make of PVC conduit - Kinjal /atul / plaza AKG |
| 155 | (a) One lightpointcontrolled by oneone way switch |
| 156 | (b) One fan/ exhaust fan pointcontrolledby one one way switch |
| 157 | (c) One 3/5 pin socket outlet 5 Amp on the same board with other swithes. |
| 158 | (d) One 3/5 pin 5 Amps socket outlet on independent board. |
| 159 | (e) One lightpointcontrolled by two, two way switch |
| 160 | (f) One bell pointcontrolled by one way bell push |
| 161 | Allas per item No 1 abovehere inbut with 2.5 Sqmm (nominal area) FRLS cable PVC for the 15 Amp 3/5 pinsocket power point including 2.5 Sqmm copper conductor green as colour for earth contineuity all as specified. |
| 162 | S&F switch piano flush type polycarbonate single pole one way 5 Amps.Make: Havells / Anchor PC /Legrand” |
| 163 | S&F switch piano flush type polycarbonate single pole one way 15 Amps.Make: Havells / Anchor (Penta) /Legrand” |
| 164 | S&F socket outlet polycarbonate 2 in 1, 3 pin 5 Amps flush type.Make: Havells / Anchor PC /Legrand” |
| 165 | S&F socket outlet polycarbonate 2 in 1, 3 pin 5/15 Amps flush type.Make: Havells / Anchor (Penta) /Legrand” |
| 166 | S&F 2 way switch all as speicified and directed |
| 167 | S&F electronicfan regulator 230 volts , step type (5 step) socket type ,hum free 100/300 watt complete all as specified and directed. Make: Anchor(Penta)/Havells(REO)/ Legrand |
| 168 | M&L for Ceiling rose in poly carbonate 3 terminal brass flush type 6 Amps,250 volts ACISI marked, fixing on 3 mm thick sunmica hylum plastic laminated round sheet 75mm dia complete all as specified and directed. Make: Havells (ROHS) cat part No . AHLHXCW000 orAnchor PCcat part No- 3907250916 / SSK cat part No B07QS98JCQ |
| 169 | S&Fbatten holders (metal ring) PVC / polycarbonate type with back plate, fixing on 3 mm thick sunmica hylum plastic laminated round sheet 75mm diacomplete suitable for LED bulb all as specified and directed. Make: Havells (ROHS) cat part No AHLHXAW000 orAnchor PCcat part No- 3980051170 / SSK cat part No 76 |
| 170 | Supply and fix LED bulb 12 watts with B-22 base operated on single phase AC supply complete as per Make : Wipro/Havells/Bajaj/C&S |
| 171 | Supply and fix bell din dong single phase 50Hz, 230 volt completed all as speicfied and directed as per Make : Anchor/Havells/Bajaj |
| 172 | M & L for concealed modular Point wiring with 1.5 Sqmm(Nominal area) PVC insulated, unsheathed FRLS multi stranded copper conductor single core cable 1100 Volt grade drawn through and including PVC conduit of 20 mm diaISI marked with complete accessories, including modular type galavanised iron steel sunken 2.5mm thick boxes suitable for switches, sockets, modular sheet of suitable thickness , with metal junction box,also including PVC insulated and unsheathed single core multi stranded copper conductor cable of size 2.5 sqmm green in colour as earth continuity conductor connected to common earth dolly, including taking down of existing point wiring and their connected fittings & fixtures like switches, sockets, Ceiling rose, fan regulator etc and making good to disturbed surface with white wash or any type distemper as per existing colour of building , complete all as specified and directed for the following :- Note for Point wiring:- (i) The quoted rate is deemed to be include the price of G Isunken box for switches, sockets etc of any size & shape. (ii)The quoted rate is deemed to be included rate of dismantling of existing point of any type including fittings & fixtures complete. Make of Cable- Havells lifeline / polycab / Plaza, Make of PVC conduit - Kinjal /atul / plaza AKG |
| 173 | (a) One lightpointcontrolled by oneone way switch |
| 174 | (b) One fan/ exhaust fan pointcontrolledby one one way switch |
| 175 | (c) One 3/5 pin socket outlet 5 Amp on the same board with other swithes. |
| 176 | (d) One 3/5 pin 5 Amps socket outlet on independent board. |
| 177 | (e) One light point controled by two, two way switch. |
| 178 | (f) One bell point controled by one, one way bell push. |
| 179 | Allas per item No 11 abovehere inbut with 2.5 Sqmm (nominal area) FRLS cable PVC for the 15 Amp 3/5 pinsocket power point including 2.5 Sqmm copper conductor green as colour for earth continuity all as specified. |
| 180 | S&F switch modular type single pole one way 6 Amps.Make: Havells / Anchor PC /Legrand” |
| 181 | S&F switch modular type single pole one way 16 Amps.Make: Havells / Anchor (Penta) /Legrand” |
| 182 | S&F socket outlet modular type 2/3 pin 6 Amps 2 module.Make: Havells / Anchor PC /Legrand” |
| 183 | S&F socket outlet modular type 2/3 pin 6A/16 Amps 2 module.Make: Havells / Anchor (Penta) /Legrand” |
| 184 | S&F switch 2 may moduler type06 Amps one mdoule |
| 185 | S&F electronic modular type fan regulator 230 volts , step type 2 module ,hum free 120 watt complete all as specified and directed. |
| 186 | S&F In replacement of old unserviceable light fittings LED tube light fitting20 Watt industrial batten box type withbipin holders connector block complete with all accessories internally prewired and incl connecting upthree core single wire incl 01 no. 20 wattretrofit LED tube rod T8 polycarbonate to be fixed at any height of wall/ceiling complete all as spd and directed . Make : Havells (Rod) Cat No-PHOTONULTRAE 2.01213T8SSTL20WLED865SPC Havells (Batten) Cat No- REGALBATTENT 8UPTO1X22WSSBSWH or Bajaj (Batten) Cat No- 112181 BLRB-DB 118, Bajaj (Rod) Cat No - 112481 BLRB 21W CWC or C&S LTDC0161820WLED + LT4F20WLEDT8WD. |
| 187 | S&F LED light fitting mirror type with high ourput diffuser 2 feet, 10 watt, 220 volt AC decorative type with driver holder and LED lemp including connecting up with three core flexible coper conductor cable of suitable size. |
| 188 | S&F LEDbulk head light fitting almunisum housing with poly corobate difuser of capacity 12 Watt complete all as directed Make: C&S Sirius Series Cat No LTB12WLED or equv in Bajaj/Havells |
| 189 | S & F In replacement of old unserviceable Building security light fitting versatile pressure die-cast aluminium with high power LED 25 W as light source complete with LED 25 W 5000Kincluding bracketsmade out ofGI pipe light gradepipebent to shape incl 02 Nos MS flate clamps inclnut bolts connectioncomplete all as spd and directed .Make : C&S cat part No.LTESSI25WLED or BAJAJ CAT No - 169821 BCLST 25W LED I or Wipro Cat No - D923065. |
| 190 | Taking down old sub main wiring and S & F Sub main wiring with two runs of single core FRLS PVC insulated and unsheathed multistranded, copper conductor cable of size 4.0 sqmm LT, 1100V grade, down trhough and incl adequate sizes PVC non metallic conduit of 20mm/approprite dia with accessories and fittings and one run of 4.0 sq mm single core multi stranded copper conductor cable as earth continuity conductor. Two runs of cable one run of earth wire and one run of PVC non metallic conduit of 20mm/approprite dia shall be measured as one run length, Cable required for connection to DBs shall deemed to be incl and shall not be measured separately. Earth wire shall run inside the conduit pipe (Note :- Extra length of cable required for connection to MCBs shall deemed to be included in unit rate.) Make of Cable- Havells lifeline / polycab / Plaza, Make of PVC conduit - Kinjal /atul / plaza AKG |
| 191 | All as per item No-19here in before but 6.00 Sqmm copper conductor and 6.0 Sqmm as earth continuity conductor complete all as specified. |
| 192 | S & F In replacement of old unserviceable Distribution board (DB) VTPN 4 way made out of sheet metal enclosure (CRCA sheet) dust and vermin proof IP 43 (double door) with 250 Amps rated copper bus bar neutral bar ,earth bar,triple pole and neutral , with provision for 160A MCCB as incomer and MCBs TP/DP/SP as outgoer ,flush to wall complete all as specified and directed. MAKE-LEGRAND : Cat No 5077 45 or C&S Cat No - CSDBMCCB100DD04IP43S or INDOASIAN Cat No - 811888 |
| 193 | S & F in replacement of unserviceable MCCB 100 Amp four pole, 415 volt, 25kA adjustable thermal and manetic setting including necessary connection complete all as specified and directed by Engr-in-Charge. Make: : Legrand cat part No.4200 55 or Indo Asian Cat No 830272 or C&S Cat No- CSEMX125FMU4P-A |
| 194 | S & F In replacement of old unserviceable Distribution board (DB) made out of sheet metal enclosure (CRCA sheet) dust and vermin proof SPN 8 way IP 43 (double door) with 100 Amps rated copper bus bar neutral bar ,earth bar ,single pole and neutral 250 volts ,flush to wall complete all as specified and directed MAKE-L&T Hagar Cat No - Y81082 , INDOASIAN Cat No - 811807 , LEGRAND cat No - 507611 |
| 195 | S & F In replacement of old unserviceable Distribution board (DB) made out of sheet metal enclosure (CRCA sheet) dust and vermin proof SPN 4 way IP 43 (double door) with 100 Amps rated copper bus bar neutral bar ,earth bar ,single pole and neutral 250 volts ,flush to wall complete all as specified and directed MAKE-L&T Hagar Cat No - Y81082 , INDOASIAN Cat No - 811807 , LEGRAND cat No - 507611 |
| 196 | S & F In replacement of old unserviceable MCBs double pole , 40 Amp 240 volt C-curve 10 KA, MAKE-L&T Hagar , INDOASIAN Cat No - 811174 , LEGRAND cat No - 408637 |
| 197 | S & F In replacement of old unserviceable MCBs single pole (SP), 10-32 Amp 240 volt C-curve 10 KA, MAKE- L&T/Indo Asian/Schneider |
| 198 | S&F single pole and neutralsheet metal enclosure with two pin and earth plug and socket also including MCB Single Pole 20 Amps, 240 Volt and fixed flush in wall suitable for geyser /AC connection, complete all as specified and directed.Make :Indo Asian or L&T or Schneider |
| 199 | M&L earthing complete with galvanized steel plate electrode 600 mm x 600 mm x 6 mm thick, burried directly in ground vertically in pit of depth not less than 2.25 metre below normal ground level with top edge of the earth plate at a depth not less than 1.5 metre below normal ground level surrounded from all sides with mixture of charcoal and common salt in alternate layers and electrode connected to galvanized iron wire 4mm dia size by means of GI bolts, nuts, check nuts and washers, earth strip protected by galvanized steel pipe 20 mm bore (light grade) connected to main switch board or any other electrical equipment all as shown in electrical plate No. 3 ofSSR-2009 Part I and includingnecessary excavation and earth work in any type of soil, 20 mm bore medium grade GI pipe for watering, funnel with wire mesh, PCC (1:3:6) (chamber size not less than 300x300x300mm interier diamentions), type C-1 chamber, RCC (1:2:4), type B-1, reinforced with 6 mm dia MS round bars @ 15cm c/c both way for cover and MS frame etc., complete all as specified. NOTE: The unit rate includes earth strip and protection pipe upto (maximum 7.5 metre from earth plate) earth point/test point. and chamber shall be made 0.5 mtr away from the earthing pit. |
| 200 | Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25.00 sq mm 4 core incl cable procection pipe fixing with clamp, nuts, and washersetc complete all as specified and directed |
| 201 | Excavation in trenches not exc 1.5 m wide and not exc 1.5 mtr deep in any type of soil (soft/ loose/ hard/ dense soil) for laying / taking up / taking down of electric power cable and getting out and leveling of bottom surface to required level all as specified and directed by Engr –in- Charge. |
| 202 | Returning filling, in including spreading, leveling, watering and well ramming soils in layers not exceeding 25 cm thick all as specified and directed. |
| 203 | Removing excavated material from site to a distance n exc (50 mtr away and exc 1.5 m above the starting point all as specified and directed by Engineer-in-Charge. |
| 204 | Material and labour for river washed and screened dry sand for filling in trenches below and around underground cables for cushioning of cables etc, complete all as specified. |
| 205 | Supply& lay in trenches sub class `B’ bricks having compressive strength 75 Kg/ Sqcm for cable protection etc compete all as specified and directed by Engineer-in-Charge. |
| 206 | Supply and fix electric storage water heater of 25 Litre capacity including necessary grouting screws, non return valve, and PVC connection of chromium plated wire mesh outer cover for Hot and cold water separate complete all as directed.Make: Havells Model SENZO CatNo GHWASESWH025 White-Grey |
| 207 | S&F Ceiling fan 1200 mm Sweep with complete accessories incl fan regulatorAC, 240 volt, single phase including making connection complete all as directed by Engineer - in -Charge.Note: Old unserviceable fan will be deposited to MES Store. Make : Havells Pacer white 1200 mm or equivalent in Bajaj / Havells |
| 208 | S&F metal body Exhaust fan 300 mm Sweep with louvers, 240volt, single phase including making connectioncutting holes of suitable dia for exhaust fan in any type of wall including finishing and making good as per existing surrounded wall complete all as directed by Engineer - in -Charge.Make : Havellsturbo Force SP 300 mm or equivalent in Bajaj / Havells |
| 209 | S&F PVC Ventilation (exhoust) fan 250 mm Sweep with louvers, AC 230 Volt, single phase including making connectioncutting holes of suitable size in any type of wall including finishing and making good as per existing surrounded wall complete all as directed by Engineer - in -Charge. Make : Havells Model Ventil AIR - DXZ white 250 mmor equivalent in Bajaj / Crompton |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
